Search Documents

By R. L. Virta

Common clay is a natural, fine-grained material composed of hydrous aluminum silicates. Shale is a laminated sedimentary rock that is formed by the consolidation of clay, mud or silt. Production About 160 companies produced common clay and shale in 41 states. In states not reporting production, common clay and shale probably was mined and sold for construction applications by companies not participating in the U.S. Geological Survey’s canvass of producers.

Jan 1, 2005

By Charles Stone, Madan Naik, Drupad Desai, Karel Rossler

Planning of New York’s new subway line dictated the location of shallow underground station caverns and track crossovers. Clear span openings ranging from70 feet to 100 feet and lengths in excess of 1000 feet, coupled with low rock cover ranging from 25 feet to 40 feet required judicious selection of construction methods, equipment, and proper sequencing of the excavation stages. Rock classifications alone could not predict the behavior of the rock mass during construction. A robust design procedure that considered most of the important aspects of rock behavior and elements of shallow tunnel design, minimized the negative impacts of variable geotechnical data. This paper describes the intricacies of the planning and design of the $16 billion Second Avenue Subway with insight into how to overcome the design complexities and construction challenges of the urban underground.

Jan 1, 2005

By T. C. Eisele

The use of column flotation was considered for the ?reverse flotation? of iron ore, where the gangue (quartz) was recovered in the froth product. This use of the froth for carrying the gangue mineral rather than carrying the valuable concentrate significantly changes the operational requirements of the column. The objective of this work was to determine which of several column flotation technologies would be most suitable for this type of flotation operation. Studies were carried out using both the Jameson column and the Deister column. Comparative results are presented that show the capabilities of both column types in this application relative to conventional Wemco flotation cells. Columns were demonstrated to have grade-recovery performance superior to what could be achieved with conventional cells. Two-stage flotation with the columns could produce a concentrate that was up to 70.2% Fe at 87.5% iron recovery, compared to 70.4% Fe at only 77.7% iron recovery for four stages of flotation in conventional cells. It was shown to be particularly important to operate the columns to recover a maximum of the quartz gangue into the froth. It was noted that there are often problems in scale-up of laboratory columns to plant scale, because the increase in height and the decrease in the ratio of height to diameter at the larger scale allows more axial mixing and bubble coalescence, both of which degrade the column performance. Horizontal baffling was shown to improve column performance by reducing axial mixing and breaking up large bubbles, and so the use of such baffles in the reverse flotation application was investigated.

Jan 1, 2007

By Paul M. Godlewski, Joseph P. Gildner, David S. McAllister

With construction underway on the 22.5 km (14 mile) Initial Segment of the Link Light Rail transit system in Seattle (including the one-mile EPB-driven running tunnels and mined station at Beacon Hill), the Sound Transit Board on May 20, 2004 voted on selection of a preferred route for an approximately eight-mile extension northwards from the central business district to Northgate, and authorized immediate start of advanced conceptual/preliminary engineering and geotechnical exploration programs scheduled to be completed in Spring 2005. The extension includes approximately914 m (30,000) route-feet of bored running tunnels, a mined station with platform level approximately 60 m (200 ft) below grade, three (possibly four) cut-and-cover stations and a cut-and-cover cross-over structure, as well as an aerial terminal station at Northgate and other line-section below-grade and aerial structures. All tunneling will be in glacial soils.

Jan 1, 2005

By D. Potter

In 1990, Freeport Exploration began regional reconnaissance exploration programs in Irian Jaya, the easternmost province of the republic of Indonesia (Fig. 1). Irian Jaya occupies the western half of the island of New Guinea. Freeport was awarded an initial contract of work that totaled 2.6 million hm2 (6.4 million acres). The company was subsequently awarded additional concessions that added 1 million hm2 (2.5 million acres). The concessions require work commitments and periodic relinquishments. Due to these relinquishments, Freeport’s current land position totals 1.9 million hm2 (4.7 million acres). Freeport began the exploration program to locate additional Grasberg deposits, the largest deposit in the Ertsberg district. But the company recognized that other types of deposits could be present in the largely unexplored area of Irian Jaya.

Jan 1, 1999

By Roy Woodall

Successful mineral exploration is the lifeblood of the mining industry. Contrary to what the environmental lobby would have the world believe, the industry is replacing the metals it is extracting. The reserve base has not changed significantly in 20 years (Fig. 1.) Mineral exploration is a research activity. First there is the idea, the vision or the intuitive thought. The experiments follow. These involve repeated phases of data gathering, data interpretation and concept testing through drilling. For many companies, exploration is the main investment in scientific research. Each mineral exploration experiment may involve years of costly work. Despite the improving tools of science and technology, the investment remains high-risk. Only the promise of high rewards, or desire to survive as a mining company, will stimulate the necessary commitment and level of investment. Confidence that an economic return can be achieved, confidence in the science and technology being applied and confidence in the people involved are the foundations upon which successful mineral exploration is built (Woodall, 1984). The challenges facing the explorationist in the 1990s fall into two categories: - the challenge to make the activity economic; and - the challenge to make the activity socially and, therefore, politically acceptable.

Jan 1, 1992

By G. C. Presley

Estimated domestic production of pumice and pumicite in 2004 increased about 23 percent since 2003, according to the U. S. Geological Survey (USGS). The USGS estimate of domestic production of 687 kt(757,000 st) for 2003 turned out to be 870 kt (959,000 st)of actual production. The USGS estimated the value of pumice and pumicite sold or used in the United States to be $26 million in 2004, up $4 million from the value in 2003. There was an estimated decrease in the mine, or mill, average price to $24.14/t ($21.90/st) in 2004 from $25.19/t ($22.85/st) in2003.

Jan 1, 2005

By Z. Konstantinovic, M. Ahrens

Due to the large installed electrical power and the large number of electric drives in minerals and mining plants power factor compensation and harmonic filtering has always been an important issue. For the design of harmonic filter and power factor compensation installations several approaches can be taken. The paper describes different concepts and their advantages and analyzes special requirements and design considerations for minerals and mining plants. It also highlights areas where problems can occur and which points need to be addressed carefully. Optimized designs and solutions are discussed in case studies and the resulting energy savings and benefits for the plant operation are shown.

Jan 1, 2007

By P. Mills

The four top barite-producing countries in the world are China, India, Morocco and the United States. China is currently the largest exporter of barite followed by India. More than 95 percent of the barite mined today is used by the petroleum industry as driller’s mud. The rest is used in the industrial market and the medical field. Most of the barite mined in the United States is in Nevada. This year, mining activity has increased due to an increase in oil exploration/development. This was caused by an increase in the crude oil prices.

Jan 1, 2005

By Bruce Cavender

Historically, the processing function has been regarded as efficiently managed as long as production costs were kept low, recovery was adequate and sufficient plant capacity was avail-able. In this paradigm, processing is viewed as capable of making only a limited contribution to a company?s competitive advantage. However, the processing function can provide a primary vehicle for building critical competitive capabilities. Processing organizations should be encouraged to become so accomplished they generate new opportunities for other functional groups and thereby influence a company?s overall strategy. This requires a deep shift in processing?s role, in its self-image and in the expectations of it held by managers in other functions. Specific plant improvement techniques ? total productive maintenance (TPM), loss control, etc. ? should be viewed primarily as means for building strategically valuable processing capabilities. Different improvement strategies create different kinds of capabilities and present new strategic options. Broadly speaking, a mineral-producing company seeks competitive advantage through two principal activities: the development of new mineral production and reserves and the optimization of existing operations. These lead to increases in ore reserves, production levels and cash flows that are manifested in increased profitability and, hopefully, increases in the price of the firm?s stock. The profitability of a minerals company is a function of the overall profitability of the industry sector in which the company participates and the firm?s competitive position within that sector relative to those of its competitors. Competitive advantage within the industry comes from two sources: the ability to maintain lower prices than competitors for the same product (cost leadership), or from the sale of products with unique properties that justify higher prices (product differentiation; Porter, 1980). Most mineral companies produce fungible commodities that are sold to anonymous customers, and sustainable cost advantage is the only long-run strategy available to these companies to enhance profitability.

Jan 1, 2008

By W. G. Brunner

The slurry wall technique has undergone an evolution from its invention to its today’s status. In the early stages slurry walls were built with cable grab, later on with much stronger hydraulic grab and last but not least with the use of the cutter technique. The cutter allows thick walls with high verticality to extreme depths through hard soil and rock formations. With the rising demand of the construction of watertight diaphragm walls different joint systems have been developed. In addition to the rapid development of excavation systems it was necessary to improve slurry treatment and desanding plants, especially in conjunction with high performance trench cutters. Deep mixing methods can be used economically for the construction of cut-off or excavation support walls where other systems such as traditional soldier beams and lagging walls would yield unsatisfactory performance, where the installation of vibrated or driven sheet piles could cause vibration induced settlements and where concrete diaphragm walls would be time consuming and expensive. The new CSM method can largely replace the more conventional single or multiple auger methods of soil mixing or jet grouting. The cutter tool is similar to a cutter used in diaphragm walls or cut-off walls and is operated with a Kelly mounted on a drilling rig or rope suspended on a crane jib or mast of a base carrier. With this system much deeper walls can be installed and even hard soil layers can be penetrated.

Jan 1, 2007

By Philip Weaver

The MIDAS project is funded by the European Commission (DG Research) and began on the 1st November 2013. The project will investigate the environmental impact of deep-sea mineral and energy extraction: specifically, polymetallic sulphides, manganese nodules, cobalt-rich ferromanganese crusts and the potential mining of rare earth elements. As deep-sea mining becomes ever closer, and the International Seabed Authority begins to develop its regulatory framework for exploitation of deep-sea minerals, MIDAS is well timed to provide fundamental scientific information. The MIDAS partnership represents a unique combination of scientists, industry, social scientists, legal experts, nongovernmental organisations and small and medium enterprises. MIDAS is carrying out research into the nature and scales of the potential impacts of mining including 1) physical disturbance of the seabed by mining, the creation of mine tailings; 2) the potential effects of particle-laden plumes in the water column, and 3) the possible toxic chemicals that might be released by the mining process. Key biological unknowns, such as connectivity between populations, impacts of the loss of biological diversity on ecosystem functioning, and how quickly the ecosystems will recover will all be addressed. The plan is to use this information to aid development of recommendations for best practice in the mining industry. A key component is the involvement of industry within the project and through stakeholder engagements to find feasible solutions. The project will work closely with European and international regulatory organisations to take these recommendations forward into legislation. A major element of MIDAS will be to develop methods and technologies for 1) preparing baseline assessments of biodiversity, and 2) monitoring activities remotely in the deep sea during and after exploitation, including ecosystem recovery. To carry out this work MIDAS is conducting a number of research cruises to examine the above issues at potential sites for exploitation of SMS and nodule deposits. This talk will present some of the recent findings of the project.

Sep 1, 2014

By Juan P. Camus

Mining is one of the oldest industrial activities. Its products are essential to modern civilization. Paradoxically, and despite a deep-rooted belief to the contrary, mining is not a lucrative industry— at least not in the aggregate. This assertion is true not only for recent years, one of the weakest periods in terms of metal prices, but also for a long time past. In 1776,Adam Smith said in The Wealth of Nations: “Of all those expensive and uncertain projects, how-ever, which bring bankruptcy upon the greater part of the people who engage in them, there is none perhaps more perfectly ruinous than the search after ... mines. It is perhaps the most disadvantageous lottery in the world... Projects of mining, instead of replacing the capital employed in them, ... commonly absorb both capital and profits.”

Jan 1, 2002

Inn mining communities throughout the western United States, cows have always been part of the landscape as they graze on surrounding rangelands. Until recently, mining companies regarded these animals as something to be kept off their properties — especially any freshly reclaimed lands. During the last few years, though, this situation has begun to change. Today, cattle can be seen in a handful of mine settings, moving up and down the slopes of mine tailings and waste rock. These animals are being used by several companies to do some of the reclamation work once performed by large earth-moving equipment, mechanical spreaders, rippers and seed drillers. This is because cows can contour slopes more naturally and produce and spread soil nutrients in ways that tractors and ripping machines cannot.

Jan 1, 1999

By Steve Chorley

Open-type, or main beam, tunnel boring machines (TBMs) can achieve impressive rates of production. This type of TBM typically outperforms other types of TBMs currently in use around the world. In good ground conditions, main beam machines have achieved production rates of more than 1 km/month (0.6 miles/month). However, installing effective ground support in poorer rock conditions on main beam machines can be a major cause of concern. The design of main beam machines is such that installation of ground support equipment, particularly at the front of the machine in what is commonly known as the L1 support zone, has traditionally been limited to rock drills and basic working platforms. Personnel working in the L1 zone have, until recently, been protected by roof supports and extended fingers, often with restricted access to working areas.

Jan 1, 2011

By William Reininger

Microtunneling provides a necessary solution for multiple utility crossings associated with the New York Metropolitan Transportation Authority Capital Construction Company?s (MTACC) Eastside Access Project for the Long Island Rail Road. Construction of four TBM tunnels and their approach structures at the eastern end of the project in Sunnyside, Queens required significant modification and expansion of the railroad infrastructure at this location. Maintenance of railroad traffic during project construction is a principal requirement. As a consequence fourteen (14) utility crossing segments are being installed under active traffic by microtunneling methods. Microtunnels were installed in a variety of conditions including depths, types of soils and construction restraints.

By S. F. Diehl

Drill cores from uranium roll-front deposits, hosted in lower Cretaceous strata, were examined from the proposed Dewey Burdock in-situ uranium recovery site in the northern part of the Edgemont uranium district, South Dakota. Uraninite (UO2), coffinite U(SiO4)0.9(OH)0.4, and doloresite (H8V6O16) occur as pore-occluding cements within the Fall River Formation in the Dewey area. In contrast, within the Lakota Formation in the Burdock area, uranium (with very little vanadium) is absorbed onto woody fragments and amorphous carbonaceous material in pressure-solution seams. Both areas have typical uranium roll-front mineralogy with 0.5 wt. % pyrite in the reduced solid phase and no pyrite in the oxidized solid phase. The groundwater at the ore zone is not oxygenated, so the uranium is relatively insoluble. Uranium in solution in ground waters is <10µg/L at Dewey and <22 µg/L at Burdock. Micromineralogic and geochemical data are being used to understand water/rock interactions, uranium distribution and movement, and as input factors for predictive reactive transport models.

Feb 27, 2013

By Janet A. Flinn, David G. Fileccia

Machine guidance and control systems have become more pervasive in the mining industry in recent years but not always from mining-experienced providers. Dozers, motor graders, scrapers, excavators, shovels, draglines, drills and haul trucks are just a few examples of the types of heavy machinery now equipped with global positioning system (GPS)-aided guidance systems. While equipment manufacturers are offering their own software, many only supply solutions for the machines they produce. The proliferation of GPS equipment manufacturers entering the machine guidance and control arena has resulted in a multitude of makes and models of GPS receivers. Some of these companies also produce their own guidance software. But they usually just specialize in a narrow range of heavy machinery. So customers are forced to use multiple systems and face new challenges in implementation, training, reporting and inter-system communication.

Jan 1, 2006

A series of gas inrush events occurred during development at Grosvenor mine resulting in exposure to elevated levels of methane at the production face. A total of 22 gas inrush events occurred releasing between 15 and 130 m3 of methane during each event. The presence of an undrained seam in the immediate floor, geotechnical characteristics of the floor, and the stress environment all contributed to these dynamic floor events, while the geological characteristics of the seam below, such as the seam thickness and ash content of 75%, prevented effective pre-drainage. However, events only occurred in headings mined parallel to the principal horizontal stress direction. In cut-throughs (C/Ts) perpendicular to the principal stress direction, no events occurred, and higher methane levels were observed at the production face.

Jan 7, 2020

By Wolfgang Roth

In 1990, a residential area above the North Outfall Sewer (NOS) tunnel constructed in 1924, experienced subsidence. After sewage was diverted into the North Outfall Replacement Sewer (NORS), soil probing from within the tunnel was conducted, soil-improvement options were developed, and a preferred grouting scheme was analyzed by numerical modeling to evaluate the stability of the 80-year+ old tunnel liner under grouting-induced loading conditions. This paper discusses the initial field investigation and the development and analysis of a grouting scheme originally intended to be implemented before relining of the tunnel. The scheme was later modified, and the new liner was installed before the final probing and grouting work was done.

Jan 1, 2008