Search Documents

By S. L. Chen

Keywords: copper, concentrate drying, steam dryer, dryers By placing additional demands on energy and gas flow, the moisture content of a copper concentrate has an adverse effect on the smelting process. Different drying technologies, such as directly heated rotary dryers, flash dryers, and steam dryers, are available to solve this problem. The energy requirements of and off-gas generated from different dryer types are compared. The performance of the steam dryer was found to be superior to that of the others. In particular, the rotary steam dryer and its benefits are discussed. Structural properties confer an advantage on the rotary steam dryer, for wear on tube elements is eliminated, and drying efficiency is improved. If steam is available, the rotary steam dryer is an excellent choice for drying copper concentrates.

Jan 1, 2006

By M. J. Little

Potgietersrust Platinums Ltd (PPRust) is Anglo Platinum?s only open pit operation. The major slope stability concern at PPRust is rapid, small-scale brittle failure on the west wall of Sandsloot open pit. In order to improve safety and mine more economically, a comprehensive slope monitoring strategy has been implemented. In the last 3 years four new state-of-the-art monitoring systems have been installed namely an ISSI microseismic monitoring system, a GeoMoS automated prism monitoring system, prismless Riegl laser scanners and a GroundProbe slope stability radar (SSR). Groundwater monitoring and visual monitoring have also been improved over the same time period. To complement the visual inspections, SiroVision digital photogrammetry is now used for predicting where future failures may occur. All these monitoring tools provide primary monitoring which is used to identify high risk areas. The SSR is then set up in that area to provide early warning of failure so evacuation can be successfully done. Fault tree analysis has proved that with this comprehensive slope monitoring strategy the geotechnical risk at PPRust is greatly reduced, allowing mining to continue safely and economically in challenging conditions.

Jan 1, 2006

By J. D. Steenkamp

"In July of 2016 and June 2017, major tap-hole repairs were carried out during the annual shutdown of two 63 MVA submerged arc furnaces producing ferrochromium in South Africa. The hot excavations of the tap-holes allowed for a study of the wear profiles. Subsequent thermodynamic calculations allowed for the quantification of the potential for chemical reaction between refractory and slag or alloy contributing to wear in the tap-hole area. Results from both wear profiling and thermodynamic calculations are reported here. IntroductionFerrochrome (FeCr) is an essential alloy in the production of stainless steel (Gasik, 2013). In 2017, 11.7 Mt of FeCr was produced (Pariser et al., 2018.). The main producers were China (39%), South Africa (29%), Kazakstan (12%), and India (8%).A number of grades of FeCr are available to producers of stainless steel, including high-carbon ferrochrome (HCFeCr) (Gasik, 2013). HCFeCr typically contains 60–70% Cr and 4–6% C (Basson and Daavittila, 2013). When the chromium content is lower (50–55% Cr) and the carbon content higher (6–8% C), it is referred to as charge chrome. Charge chrome is typically produced in South Africa due to the grades of ore available.FeCr is produced in submerged arc furnaces (SAFs) and in open arc furnaces (Mc Dougall, 2013) by carbothermic reduction of oxide raw materials. In a SAF the electrode tips are submerged in a porous charge mix. In FeCr production, the electrical energy is mainly liberated by resistive heating of the wet coke bed (Barker et al., 2007; Steenkamp et al., 2017). Thermally conductive lining design philosophies are typically applied in SAFs producing FeCr (Steenkamp, Denton, and Hayman, 2017; Coetzee, Duncanson, and Sylven, 2010; Coetzee et al., 2010).In July of 2016 and June of 2017, major tap-hole repairs were carried out during the annual shutdown of two 63 MVA SAFs producing FeCr in South Africa. The hot excavations of the tap-holes allowed for a study of the wear profiles. Both SAFs were operated on the same site, by two different operating crews, using the same raw materials. The major difference between them was that the SAF excavated in 2016 was an open SAF (referred to as Furnace A) and the one excavated in 2017 was a closed SAF (referred to as Furnace B). In an open SAF, a gap exists between the top of the steel shell and the roof, with the top of the burden being open to the atmosphere and the CO-rich off-gas being combusted as it escapes. In a closed SAF, the roof is attached to the steel shell and the CO-rich off-gas is collected from an offtake on the roof for further treatment and used in downstream processes.The paper presented here reports the macro-scale observations on refractory wear for the two SAFs, and studies the potential for chemical wear of refractory by slag and alloy as a potential contributing factor to the tap-hole wear observed."

Jun 1, 2019

In this study, the effects of slag compositions, slag amount, temperature, and carbon content of steel on the manganese and phosphorus distribution ratios during converter steelmaking were analysed using the classical regular solution theory, and industrial tests were performed using two 80 t top-and-bottom combined blown converters (duplex melting process). The results indicate that the slag amount, temperature, and carbon content in steel are the main factors affecting the manganese yield when converter slag compositions remain constant. The FeO content of the slag has a strong impact on the manganese distribution ratio, while the slag basicity and MgO content have no obvious effect. The calculations and experimental results show that the phosphorus distribution ratio increases sharply with increasing slag basicity R, but then decreases with the increase of MgO and MnO contents in the slag. The final slag in converter steelmaking should have the following characteristics: 3.5 < R < 4.5, 15% < (FeO) < 20%, and 6% < (MgO) < 8%. The slag amount should be controlled appropriately at the same time. The results of this investigation would be useful in deciding on the application of manganese ore in alloying and identifying the slagging regime in converter steelmaking.

Jan 1, 2014

By A. McLean, M. Iwase, K. Wakimoto, K. Katogi, Y. Kikuchi

One of the greatest obstacles to the application of physical chemistry principles to the elucidation of slag-metal reactions is a lack of knowledge of activities of the reacting species. To a large extent, oxygen potential of the slag phase governs iron and steelmaking practice. Without oxygen control by means of appropriate sensors, the behaviour of the other elements cannot be managed. In this paper, measurements of the FeO activity with various types of electrochemical FeO sensors will be described together with examples of their applications for improved strategies toward better practice for ladle metallurgy and sulphur and manganese distributions between slag and metal phases during steelmaking. Measurements of FeO activity have also been made in order to improve dephosphorization reactions. This type of work has led to significant reduction in volume of slag generated within the steelmaking vessel, which in turn has important implications for refractory wear, metal yield, alloy recovery and improved productivity. Finally, an on-line sensor is described that permits the oxygen potential to be determined for both the metal phase and the slag phase during steelmaking in the BOF.

Jan 1, 2004

By E. Machaka, A. Cornah

"Mineral resources are typically informed by multiple data sources of varying reliability throughout a mining project life cycle. Abundant data which are imprecise or biased or both (‘secondary data’) are often excluded from mineral resource estimations (the ‘base case’) under an intuitive, but usually untested, assumption that this data may reduce the estimation precision, bias the estimate, or both.This paper demonstrates that the assumption is often wasteful and realized only if the secondary data are naively integrated into the estimation. A number of specialized geostatistical tools are available to extract maximum value from secondary information which are imprecise or biased or both; this paper evaluates cokriging (CK), multicollocated cokriging (MCCK), and ordinary kriging with variance of measurement error (OKVME).Where abundant imprecise but unbiased secondary data are available, integration using OKVME is recommended. This re-appropriates kriging weights from less precise to more precise data locations, improving the estimation precision compared to the base case and to Ordinary Kriging (OK) of a pooled data-set. If abundant secondary data are biased and imprecise, integration through CK is recommended as the biased data are zero-sum weighted. CK consequently provides an unbiased estimate with some improvement in estimation precision compared to the base case."

Jan 1, 2015

By S. E. Olsen, M. Tangstad, G. Tranell, K. Berg, S. Gaal

In this study, the reduction behaviours of MnO and SiO2containing slags by solid carbonaceous materials was investigated in both small and larger-scale laboratory experiments. Five types of carbonaceous material were investigated: 2 graphites, industrial coke, anthracite and eucalyptus charcoal. The effects of the reductant type/properties on the reduction kinetics, metal composition and metal yield, have been quantified. Results show that the reduction rate is highly dependant on the type of carbon used. It was found that the reductant type significantly influenced the SiO2reduction while it did not seem to have a large effect on the MnO reduction. This may be due to the different CO2and SiO reactivities of the materials.

Jan 1, 2004

By A. S. Macfarlane

Mineral resource management (MRM) practice has developed in South Africa over the course of the last ten years, with the purpose of integrating previously isolated technical functions into a value chain aligned, process organization, responsible for mine planning and optimization. The implementation of MRM within various companies has met with varying degrees of success, often resulting in incremental improvements in the planning process and, conversely, often becoming the scapegoat for poor delivery on plans and projects. The reason for this has been, amongst others, a lack of a suitable metric to define the success rate of MRM in the business at hand, in terms of its contribution to the bottom line. This paper is the result of extensive research by the author into this subject, which has resulted in the conclusion that economic value added is an appropriate measure that will lead to real optimization and value creation in mining companies, if applied within a new, holistic model

Jan 1, 2006

By A. T. Visser

"SynopsisAlmost 20 years have passed since the cutting-edge research by Thompson and Visser on the design and management of opencast mine haul roads was conducted in South Africa. This system is based on three principles, namely the structural ability to support the ultra-heavy truck loads, the selection of vehicle and environmentally friendly riding surface, and an appropriate level of maintenance to counteract wear and tear. Obviously, proper layout and geometry are essential.These principles have been implemented worldwide, and it is useful to review the lessons learned. The objectives of this paper are to present a critical review of the status of mine haul road design and management, and the impact that these principles have made on operations, particularly the cost-effectiveness. The paper briefly reviews the principles of the haul road design and management and the extent to which they are applicable. Case studies of a number of implementations are presented to demonstrate that the principles are sound and have been applied effectively. For example, at an international operation the transport cost of coal was 40% more expensive than anticipated in the feasibility stage, and this made the mining operation uneconomic. Correction of this problem resulted in a viable enterprise. Although designed for opencast operations, the principles are equally valid for underground operations, and initial development work will be discussed.The main conclusions are that the research approach is valid and its effectiveness has been demonstrated in a number of applications. The anticipated financial benefit has been derived, and has made the mining operations that used the principles more effective. Of major importance is the application of opencast haul road design principles to the future thrust of using driverless vehicles in opencast and underground mining, where the road quality is not negotiable as there is no driver that can avoid obstacles or severe road deterioration.IntroductionAlmost 20 years have passed since the cutting-edge research by Thompson and Visser on the design and management of opencast mine haul roads in South Africa (Thompson and Visser, 1996a, 1996b, 1998, 1999, 2000a). This system is based on three principles, namely the structural ability to support the ultra-heavy truck loads, the selection of vehicle and environmentally friendly riding surface, and an appropriate level of maintenance to counteract wear and tear. Obviously, proper layout and geometry are essential."

Jan 1, 2015

By C. V. O?Keefe

Volumetric flow and mass flow are two of the critical process parameters needed to understand and control flotation processes, with others being levels, densities, and metal analyses. Both volumetric flow and density measurements can be adversely influenced by entrained air, which will result in artificially high flow readings and artificially low mass flow calculations. Array-based instrumentation has been used successfully to accurately measure both volumetric flow of aerated slurry and the quantity of air entrained within the slurry. The latter measurement has been used to correct density measurements, thus providing an accurate mass flow calculation. A case study involving the use of this technology to measure both flow rates and air entrainment levels at Eland Platinum processing facility (concentrator) will be covered in detail. In addition, with certain traditional flow meters such as electromagnetic meters, erroneous volumetric flow rates can be recorded in the presence of paramagnetic or ferromagnetic material. The use of this array technology to avoid spikes in measurements due to steel fragments passing through the pipe will also be discussed.

Jan 1, 2012

By K. Drescher

Excavations in deep level hard rock mines show rheological or time-dependent deformation responses to mining-induced stresses. These are generally not as dramatic as those seen in soft rock environments, such as potash and salt mines, but these deformations can nevertheless become substantial in time. It is usual to see total excavation closure at a much earlier stage than predicted by numerical models, and real-time measurements underground have confirmed that closure takes place on a more-or-less continuous basis, with highest closure rates observed after a blast and then slowly diminishing with passing time. This paper describes laboratory tests to determine the time-dependent response of hard rocks to loading, the results of the tests, and then quantifies these effects to explain the time-dependent phenomena observed underground. The primary intention of this work is to help explain the various time-dependent deformation processes around typical deep level hard rock tabular excavations. Three mechanisms were investigated in two typical hard rock types present in the deep level gold mines in South Africa, namely Ventersdorp Lava and Elsburg Quartzite. Uniaxial compression creep studies were done as the first part of the study followed by shear creep studies on discontinuities where crushed lava and crushed quartzite as well as a natural gouge were used as infilling. The last part of the study consisted of triaxial post-failure relaxation tests. The compression creep tests and the triaxial post-failure relaxation tests showed that the amount of energy dissipated by the lava is significantly less than for quartzite. For mines operating at depths greater than 2000 m the implication is that the lava must show a greater rockburst-proneness than the quartzite. Since the lava shows a lower post-failure stress relaxation, it can store sufficient energy for multiple rockbursts, which is seen in the clustering of multiple seismic events in the deep level mines. This study provides the first data available for energy change calculations in fractured rock masses, and provides the first general indications for rockburst intensities ahead of active mining faces.

Jan 1, 2003

By M. Berger

The ‘Metallurgical Operations’ Department of Grinaker-LTA Process Engineering (GLTA) currently undertakes then primary mining as well as the re-deposition of tailings forTicor South Africa (Ticor) at their Hillendale mine near Empangeni, KwaZulu-Natal, South Africa. The mining plant, which was designed by GLTA on a Build, Own, Operate and Transfer (BOOT) basis, is capable of mining 780 000 tons per month of ROM material which is then pumped to the Primary Wet Plant for treatment by Ticor. Hydraulic mining via high pressure water cannons and subsequent transfer of the heavy mineral slurry at an RD of between 1.35 and 1.48, has never before been undertaken successfully at this level of production on an in situ reserve. The presentation will take the form of a case study in which the unique site operating conditions will be detailed and discussed, as will the innovative process and engineering solutions employed by GLTA to overcome the engineering and production challenges encountered. In order to protect the intellectual property involved in this operation, this paper is fairly general in nature, and attempts merely to provide the reader with a broad perspective understanding of the operation, and some of the difficulties encountered during the early stages of production.

Jan 1, 2003

By A. V. Roschin, V. E. Roschin

Composite ores are more often used for production of iron in connection with reserve depletion of traditional ore crude in the regions with developed metallurgy. In particular, the majority of perspective ferrum-ore deposits of the Urals are presented by titanferous magnetite ores which contain a significant amount of titanium and vanadium alongside with ferrum. Thus, the deposits of titanferous magnetites of the Southern Urals on the average contain about 20 % of Fe, 8,7 % TiO2 and 0,24 % V2O5. Due to a high content of titanium oxides it is impossible or it is inexpedient to process such ores in blast furnaces. During work just on titanferous magnetite ore refractory titanium-containing slags are formed in a blast furnace, and in case of its dilution by ores of different types the titanium due to the small content in slag is thrown out. It is often impossible to separate such ores into ferriferous and titanferous concentrates because ferrum and titanium are present in the same minerals. This work attempts to selectively reduce ferrum in solid oxide and to separate metallic iron from titanferousslag with fast fusion. Solid-phase reduction of ferrum has been carried out with carbon at temperature of 1000? 1300°?. In products of solid-phase reduction the extremely disperse mix of metal iron and only partially reduced titanium oxides have been achieved. It is impossible to separate such a mix mechanically. However, the fast fusion of the mix allowed separating it into cast iron and slag with the high content of titanium. Thus the cast iron contained less than 0,1 % of titanium, and the slag did not contain practically any ferrum.

Jan 1, 2007

By E. Hakami

The objective of the study was to estimate the largest shear displacement that could be expected on a pre-existing fracture located in the repository area, due to the heat release from deposited waste. Two-dimensional numerical analyses using UDEC have been performed. The maximum shear displacement, at the fracture centre, amounts to 0.2 – 13.8 cm depending on fracture parameters. The fracture extension, friction angle and shear stiffness are found to be the most important. Le but de cette étude est de déterminer le déplacement maximal en cisaillement qui puisse se développer le long d&apos;une fracture préexistante en réaction à la chaleur dégagée par les déchets radioactifs enfouis dans la roche. Les analyses numériques ont été réalisées à l&apos;aide du code 2D UDEC. Le déplacement maximal en cisaillement enregistré au centre de la fracture varie entre 0.2 et 13.8 cm en fonction des propriétés de la fracture. L&apos;ouverture, l&apos;angle de friction et la rigidité au cisaillement semblent avoir une influence dominante sur les résultats. Zielsetzung der Studie war die Abschätzung der maximalen Scherverschiebung, die auf einer innerhalb des Endlagergebietes existierenden Rissfläche infolge der Wärmeabstrahlung des eingelagerten Materials zu erwarten war. Es wurden zwei-dimensionale numerische Berechnungen mit UDEC durchgeführt. Die maximale Scherverschiebung im Zentrum der Rissfläche beträgt 0.2-13.8 cm, abhängig von den Risseigenschaften. Dabei hat sich herausgestellt, dass Rissgrösse,Reibungswinkel und Schersteifigkeit den grössten Einfluss haben.

Jan 1, 2003

By D. Chetty

The characterization of platinum group minerals (PGMs) from concentrator flotation circuits provides valuable information towards understanding PGM recovery under given milling and flotation conditions. Additional mineralogical characterization also provides information on ore variability, which may affect recovery. Considering the low grades involved, automated scanning electron microscopy (SEM) characterization of PGMs has enabled relatively quick analyses, compared with older, time consuming and less accurate optical microscopy methods. Over the years, parameters, such as species, size distribution, liberation, gangue and base metal sulfide (BMS) associations, have been used to characterize the PGMs in a process mineralogical context, to aid metallurgical interpretation. This paper considers whether flotation indices determined for PGMs can be empirically validated, using initial results from analysis of PGMs in a concentrate bank from a South African concentrator treating UG2 ore from the western limb of the Bushveld Complex. The aim is to determine whether floatability is adequately described by these parameters, or whether other mineralogical factors must be considered when assessing PGM floatability, and hence accounting for recovery vs. losses to tails. The data obtained to date, show that flotation parameters (including liberation index, BMS/gangue relationships and size distribution) have merits where large changes in PGM concentration occur, as observed in the first four cells of the concentrate bank. Larger data sets, however, are required to assess floatability, particularly where concentrate cell grades are similar, as observed in the last six cells of the concentrate bank. Furthermore, the floatability indices could be enhanced by the incorporation of selected associated gangue mineral information, chief amongst these being the content and mode of occurrence of naturally floatable talc and associated orthopyroxene.

Jan 1, 2009

Paper written on project work carried out in partial fulfilment of BSc Engineering (Mining) The aim of this project is to determine whether certain pillars occurring within the no. 1 shaft and no. 2 sub-shaft ground are feasible for extraction. The extraction of these pillars is essential in prolonging the life of Kloof Main Shaft as its VCR resource becomes depleted. Extraction of these pillars will require a combination of designs and factors, with rock mechanics and ventilation being the main considerations. Primarily for the pillar extraction, an initial production target of150 kg gold, mine able in one year from commencement of ?opening up? was set. The planned target has been exceeded and the feasible pillars identified are expected to yield an additional 1 390 kg of gold to the shaft?s production profile. However, not all the required ventilation designs have been completed to date, the reason being that at the time of the project, many of the pillar areas were inaccessible and thus ventilation conditions are unknown. This project is therefore an ongoing process and will require further design once all targeted pillar areas have been opened up. A preliminary costing analysis of the pillar mining was performed and it was found that all targeted pillars with the exception of 38?61 pillar are profitable.

Jan 1, 2005

If you have problems or questions relating to the installation of this disc, please either telephone Document Transformation Technologies at (+27 12) 667 2074, or e-mail: nigel@doctech.co.za Si vous avez des problèmes relatifs àl?installation de ce disque, veuillez appeler Document Transformation Technologies au (+27 12) 667 2074, ou nous écrire par courrier électronique: nigel@doctech.co.za Produced by: / Produitpar:Document Transformation TechnologiesP O Box 560 ?Irene ?0062 ?South Africa.Tel: (012) 667 2074; Fax: (012) 667 2766; International Code (+27 12) e-mail: doctech@doctech.com website: http://www.doctech.co.za

Jan 1, 2004

By M. Kumral

A mining system consists of many sub-systems such as drilling, blasting, loading, hauling, ventilation, hoisting and supporting. During mining operation, these sub-systems may experience various problems that stop the operation because of possible environmental equipment and safety issues. In order to ensure delivery contracts in the required quality and safe mining medium, the operation should be, at least, performed in the specified reliability level of the system. If the system reliability decreases below the specified level, there will be safety and financial losses for the mining company. Therefore, the mine should be maintained by a reconstruction procedure to guarantee the operation continuity. Given that each sub-system has a different reliability function and maintenance cost, the determination of reconstruction time will be a complicated decision making problem. In this paper, the determination of reconstruction time is formulated as a nonlinear optimization problem and solved by genetic algorithms (GA). A case study was conducted to demonstrate the performance of the approach for an underground operation. The results showed that the approach could be used to determine the best action time. Keywords: mining system; genetic algorithms; reconstruction time; reliability analysis

Jan 1, 2009

By P. Mbele

Iron ore concentrate is not easily transported to, or processed in, ironmaking plants, therefore it is necessary to agglomerate. This paper will determine the possibility of agglomerating Sishen concentrate into suitable ironmaking feedstock. Pelletizing is one of the conventional and preferred agglomeration processes for iron ore concentrate investigated at Kumba Value-In-Use Laboratories. Sishen concentrate was mixed with binder, and then pelletized using a laboratory pelletizing disc; afterwards the green pellets were indurated at high temperatures to give strength high enough to survive handling and lessen disintegration in the shaft during ironmaking. Sishen pellets have satisfactory physical and metallurgical properties which make them suitable feedstock for the direct reduction processes. These were tested under Midrex shaft operational conditions and performed well, with a metallization of 94.47% being attained.

Jan 1, 2012

By S. Vorberg, J. Preussner, B. Fischer, U. Glatzel, R. Völkl, M. Wenderoth

Pt-Al-X alloys have shown good mechanical properties and adequate oxidation resistance. Starting from a promising Pt-Al-Cr alloy, the influence of Ni additions was investigated. After ageing finely dispersed precipitates are observed. Nb, Ta, Ti and Re increase strength when added as partial substitute for Al. Minor additions of B increase creep resistance and rupture time remarkably, owing to strengthening of the grain boundaries. The evolution of the alloy development programme as well as selected properties of the multi-component Pt-base alloys are presented.

Jan 1, 2006