Search Documents

By A. S. Geldenhuys, L. S. Leal Filho, D. A. Deglon, T. C. Souza Pinto

The Brucutu iron ore mine (Minas Gerais, Brazil), is Vale`s largest iron producing operation achieving around 21 million tons by flotation of iron ore pellet feed per annum. The run of mine is mainly composed of hematite (70%) and quartz (30%). After preparation (comminution and sizing), the slurry is submitted to reverse cationic flotation of quartz under basic conditions (pH=10.5). Corn starch (500g/t) is used to depress Fe-bearing minerals and alkyl (C10) ether amine is the collector for quartz. The flotation circuit is arranged in a “coarse” section utilizing dated 28m3 square Wemco cells, and a “fine” section utilizing modern 160m3 tank cells. The “coarse” flotation circuit treats material from the deslime cyclone underflow while the “fine” circuit treats material from the deslime cyclone overflow and the pulp product from the “coarse” circuit scavenger 2 bank. Evaluation of process performance is of high importance as even small gains can lead to large improvements for this high throughput plant. Cell-by-cell samples of the froth products, selected feed and pulp-products were analyzed for flow-rate, overall chemical composition, and particle size distribution. Bank-by-bank samples of the feed, froth and pulp products were analyzed on an assay-by-size basis. In addition, the flotation cells were hydrodynamically characterized and gas dispersion parameters assessed. The detailed experimental program resulted in a thorough characterization of the process and enough information to produce a calibrated floatability component model. Longer mainline residence time results in significant Fe2O3 losses while yielding little benefit in terms of SiO2 grade. Scavenger 2 has twice the residence time of scavenger 1 while having to treat only 10% of the SiO2; resulting in high Fe2O3 recoveries to the froth and poor separation. In addition, it is shown that the Fe2O3 exhibits true flotation behavior resulting in increased Fe2O3 losses. The detailed data collection campaign coupled with in depth data analysis and modelling gives unprecedented information and highlights avenues for optimization that was previously unknown. Keywords: Froth Flotation, Process modelling, Process evaluation, Metallurgical survey

Jan 1, 2020

By M. Smit, N. C. J. Dempers, S. Lunkov, C. Saguru, J. Nel

A common method for the recovery of copper is by heap leaching, solvent extraction, and electrowinning. During solvent extraction, the solution is continuously recycled, and it is necessary to remove impurities that build up in the raffinate. For the process investigated in this study, the main impurities include Fe, Co, As, and Zn. Recovery of these impurities can provide economic benefits while adhering to legal and environmental constraints. Such impurities are often removed by precipitation utilizing a neutralizing agent, such as limestone or lime, but it is also possible to remove the impurities by sulfide precipitation. Sodium hydrosulfide (NaHS) is used to selectively precipitate copper, arsenic, and zinc from a solvent-extraction raffinate stream. The resulting sulfide precipitate is bagged and sent to a roaster for further treatment. The design of the sulfide precipitation was investigated to optimize the processing conditions (including temperature, pressure, and residence time), the materials of construction, and the toxicity and explosive nature of the hydrogen sulfide gas produced

Jan 1, 2023

By R. Kuyvenhoven, A. Parbhakar-Fox, X. Prieto, J. Quevedo, L. V. Danyushevsky

This paper presents the results of a study focussed on determining the distribution of cobalt in different types of pyrite of the La Estrella IOCG deposit in Chile. In the IOCG mineral deposits, where copper is the main product, the quantification and distribution of cobalt is required to correctly define the technical and economic viability of recovering cobalt as a by-product. In the La Estrella mineral deposit, seven alteration and mineralisation events were recognised through both optical and automated electronic mineralogical analysis. Of these seven events, five different types of pyrites were identified, each with unique characteristics of the pyrite crystals. Through advanced elemental analysis of these five types of pyrites, it was determined that the concentration and distribution of cobalt within the pyrite crystal is dependent on the mineralisation event. The results indicate high cobalt concentrations in the early pyrite mineralisation events, associated with relatively fine pyrite grains, and cobalt generally occurring in a solid form in the pyrite core. The late pyrite mineralisation event exhibits the lowest concentrations of cobalt, with cobalt predominantly present along the outer periphery of the pyrite. These results are relevant from a metallurgical point of view because the preferential location of cobalt within the pyrite crystal will influence the maximum metallurgical recovery of cobalt. For this, a cobaltiferous pyrite concentrate must be formed which, according to the characteristics of pyrite, must be processed with the optimal solubilisation method. The overall objective is to ensure both good cobalt recovery and a high concentration of cobalt in the leach solution resulting from pyrite leaching. Keywords: Cobalt, pyrite, IOCG, copper, metallurgical recovery, solubilisation, Chile

Jan 1, 2020

By L. Tartibu, S. Assuli, P. Nkul, A. Kabimba, W. Elongo, N. Makhotla, D. F. Verwey, F. G. Ndiitwani, J. Bilali, T. Mukongo

The presence of colloidal silica negatively impacts various hydrometallurgy processes. This paper details the nature of colloidal silica, operational issues caused by colloidal silica, as well as various mitigation measures. MMG Kinsevere observed severe phase-continuity instability, increased crud formation, and reagent consumption, and reduced current efficiency in electrowinning with a deterioration in copper quality. Historical mitigation measures were initially implemented but failed to solve the problem. MMG Kinsevere successfully achieved efficient silica removal without adverse effect on the solvent extraction with the use of DEHSCOFIX® SC12 coagulant. A week into the coagulant trial, silica concentration had dropped from > 1500 mg/L to within 500 mg/L. The solventextraction plant recovered its stability and again operated at maximum capacity. Additionally, improvement was observed on current efficiency and copper cathodes quality with use of the coagulant.

Jan 1, 2023

By K. Naidoo, M. Pelser, J. Hagemann, K. C. Sole

The copper tankhouse at Rustenburg Base Metals Refinery is an essential component of the Anglo American Platinum value chain. The tankhouse uses starter-sheet technology that was adopted in the 1980s, so dependence on manually intensive labour and overall operational excellence has a significant impact on process performance. An efficient, stable, and sustainable electrowinning process contributes to minimising energy consumption and reducing operational costs, and enables improved product quality and increased throughput. Historic performance of this tankhouse has often been suboptimum over prolonged periods. An in-depth operational review of performance from 2018–2024 was carried out to understand challenges, risks, and high-impact factors that contribute to poor performance. Implementation of adherence to fundamental operational basics identified from global best practice, such as the frequency and quality of cell cleaning and maintenance, preventing backlogged harvesting or maintenance, preserving cell-top furniture conditions and integrity of electrodes, preventing short circuits and poor current distribution, and maintaining a high level of operational discipline, has since contributed to an era of exceptional performance. Root-cause analysis fault trees pertaining to poor current efficiency and high scrap rate are summarised. Current efficiency has significantly improved since 2021, now consistently exceeding 88%. The copper scrap rate, previously believed to be limited to a minimum of 4%, achieved a historic monthly low record of 2.06% in 2023. Chemical and physical quality has considerably improved, and cathodes exhibit minimal morphological defects.

Jun 27, 2025

FEBRUARY GENERAL MEETING The January General Meeting of the Institute was held in Kelvin House, Johannesburg on 21st January, 1970, at 4.30 p.m. Mr V. C. Robinson (Vice-President) was in the Chair. There were also present eighteen Members, Messrs M. Barcza, A. R. C. Fowler, R. C. J. Goode, Prof J. de V. Lambrechts, Messrs T. C. A. Meyer, J. A. Nixon, V. C. Robinson and P. W. J. van Rensburg (Council Members), C. A. Border, D. F. H. Grave, S. D. Hill, A. F. Lee, W. L. le Roux, C. S. Macphail, D. L Starkey, S. G. Taussig, W. T. L Wayman and Dr A. Whillier. Three Associate Members, Dr M. I. Brittan, Messrs R. Hemp and M. J. Martinson. One Student, Mr R. P. W. Henrard. Two Visitors, Dr N. G. W. Cook and Mr J. B. Smith. Secretary, Mr D. C. Visser. Total present: Twenty-six. 1. OBITUARY The Vice-President: "It is my sad duty to announce the death of the following members of the Institute: Reginald Gordon McConnell, Member, who joined the Institute on 24th April, 1946 and passed away on 26th September, 1969. James Henry Moore, Member, who joined the Institute on 28th February, 1951 and passed away on 2nd January, 1970. As a mark of respect to the memory of the deceased and in sympathy with the bereaved I would ask those present to stand and observe a few moments silence." 2. MINUTES The Vice-President: "May we confirm the Minutes of the General Meetings held on 15th October and 19th November, 1969, as published in the December, 1969 issue of the Journal?" 3. MEMBERSHIP The Vice-President: "I have pleasure in announcing that the names of the under-mentioned candidates, having been published in accordance with By-Law 5.2.2, Council has elected them to membership of the Institute in the following grades: Member: Woodford Anson Gilbert. Associate Members: Michael John Harvey Tonking, Schalk Willem Vorster, Edward Alfred Cole, Johannes Godlieb Bosch. Graduate: Leonard Raymond Kilpatrick. Affiliates: Clive Frere Knight Pouiton, David Philip Ayliff, Kenneth Gillings, Edward Gilbert East. Students: Stirling Graham Low, Petrus Stephanus van der Merwe, Louis Johannes Fourie, Clive Maxwell Winterstein. MEMBERS TRANSFERRED TO A HIGHER GRADE From Associate Member to Member: Albert Arthur Hazell, Neville Martin Hayne. "I welcome the newly elected members to the Institute and congratulate the members who had been transferred to a higher grade. 4. GENERAL BUSINESS The Vice-President: "I wish to announce that except for the student prizes awarded at the November meeting, Council has decided to make no awards for 1969. Are there any further matters to raise under the heading of General? If not, we will proceed to the next item on the agenda which is the presentation of tonight's paper. 5. PAPER FOR PRESENTATION The Vice-President: "Professor Starfield may I call on you to deliver the paper entitled "A rapid method of calculating temperature increases along mine airways". After the presentation of the paper, the Vice-President said: The Vice-President: "Thank you very much, Professor Starfield. Gentlemen, I think that many of you here, who have to do with the design of mines in an age where costs and difficulties generally, are increasing at a rate which we find almost impossible to keep up with, I would agree with you that we are fortunate to have a band of people like Professor Starfield, and others who are dedicated to producing the tools, and methods which we need to sort out these problems. I am sure that you would agree with me, that the old rule-of-thumb methods are finished forever, that we can never go back to the methods which served us in the past, when we were close to the surface and had not met the conditions which we are meeting now, and which we are going to meet in an increasing degree in the future. It is to people like Professor Starfield, with these clear, completely logically described new methods, that we look for the solution of our problems in the future. I think the whole problem of layout of any mine, is one where you can reliably prognosticate what you are likely to find in a variety of circumstances to meet the wide range of things which must happen when you consider the costs in these modern operations. Thank you very much, Professor Starfield, for coming and giving us this paper. Thank you for making plain to me how these mathematical models of yours are used. I am sure that what you have said will be a very valuable addition to the archives of this Institution. Thank you very much, indeed, and Gentlemen, will you please show your appreciation in the normal way." (Applause). Professor J. de V. Lambrechts, Mr R. Hemp and Dr A. Whillier then contributed to the discussion. (These contributions will appear in a later issue of the Journal.) PAPERS OPEN FOR DISCUSSION The Vice-President: "Listed on the agenda are papers open for discussion. I would suggest that anyone wishing to contribute to these papers submit their contributions to the Secretary in writing." CONCLUSION The Vice-President: "I wish to thank members and visitors for their attendance, and now declare the meeting closed." The meeting closed at 5.30 p.m

By M. Weir, J. R. Cutland, L A. J. Pronk van Hoogeveen

"A computer system for the design of open pits to mine stratiform orebodies has been developed for use at Nchanga Consolidated Copper Mines, Ltd. The particular requirements of such a system, for example, the accuracy of representation of geological detail and the ability to follow footwalls, arc described in this paper, together with the methods that have been adopted to satisfy them.A modified version of the Open Pit Design Program of Rio Tinto Zinc Consultants, Ltd. is incorporated in the system and the geological data are converted into a form usable by the computer by means of a pencil follower. Some of the uses which have been made of the system are described, with reference to the long- and medium-term planning of the Nchanga Open Pit, the major producing pit at Chingola Division."

Jan 1, 2014

By D. Sethuram, P. G. Koppad, S. Iyengar, R. Shobha

TiB2 and CeO2 particle-reinforced Al6061 hybrid composites were manufactured using stir casting and hot rolling techniques. The base alloy and composites were hot-rolled at 500ºC and a 50% reduction was achieved through 12 passes. The effect of varying TiB2 and CeO2 particle additions on the microstructure and mechanical properties of the Al6061 matrix was studied. Scanning electron microscopy showed uniform dispersion of both the reinforcements, with good interfacial bonding. Microhardness and tensile properties like yield and tensile strength were found to be higher for hybrid composite with 2.5% TiB2 and 2.5% CeO2 compared to Al6061 alloy and other hybrid composites. The increased tensile strength is attributed to good dispersion and interfacial bonding between the particles and Al6061 matrix. Fracture analysis using a scanning electron microscope revealed ductile fracture for the Al6061 alloy and mixed characteristics of ductile-brittle fracture for hybrid composites

Oct 1, 2021

By E. J. Y., G. J. McLachlan, E. Amini, Koha

Inferring individual component flotation rates from recovery-time data of ore complexes is important in optimising and designing minerals processing plants. However, existing two-component first-order flotation models are computationally intensive to solve using conventional non-linear least squares regression. In this paper, a Convolutional Neural Network (CNN) is used to approximate the inverse function which predicts the two-component first-order model parameters using recovery-time data. This paper compares the accuracy and computation speed of the proposed CNN against traditional non-linear least squares regression on 1 million generated data based on a known two-component firstorder kinetic model. It is shown that using a CNN is possible to approximate the inverse function for the non-invertible two-component model with recovery-time as an input matrix for convolution operations. The CNN method is 450 times faster to compute than the Trust-Region (TR) non-linear least squares regression algorithm. However, the CNN model is less accurate compared to the TR algorithm overall. Keywords: Flotation kinetics, convolutional neural network, inverse problem, modelling and simulations

Jan 1, 2020

By S. Shi, X. Xia, F. Xuesai, Z. Shen, D. Han

The hydrodynamic characteristics of a mechanical flotation cell’s transportation zone have significant impact on its metallurgical performance, especially on coarse particles recovery efficiency. However, how to define and adjust the transportation zone was seldom investigated by researchers. In this paper a method will be introduced to define the boundary of the transportation zone by PIV measurement. It is found that the transportation zone can be extended upwards by enlarging the entire rotor-stator assembly from the bottom of tank and increasing the jet angle of the impeller. Two control methods have been validated in industry tests on KYF-160m3 and KYF-320m3 air-forced mechanical flotation cells. The result shows coarse particles recovery are both improved distinctly. It is suggested that enlarging the top transport boundary is able to helpful to reduce the floating distance of bubbleparticle aggregates, which contribute to improve coarse particle recovery in large flotation cells. Key Words: Flotation cell; Transportation zone; Coarse particles flotation

Jan 1, 2020

By S. Stuurman

Inorganic acids such as sulphuric acid have found use together with certain reducing agents in leaching of copper-cobalt oxide ores. These reagents are not ideal due to the adverse effect the inorganic acids generally have on the environment and the high costs of the reducing agents. In this study a copper-cobalt oxide ore from the Central African Copperbelt was leached in two different environments; sulphuric acid in conjunction with hydrogen peroxide as a reducing agent and tartaric acid. The effects of acid concentration, reducing agent concentration, and temperature were independently determined for both leaching environments. The sulphuric acid concentration was varied between 0.4 M and 1.2 M and the concentration of hydrogen peroxide between 4.0 M and 6.5 M, while the tartaric acid concentration was varied between 0.15 M and 0.35 M. The temperature was varied between 20°C and 50°C. The results showed that the extraction of both copper and cobalt increased with sulphuric acid concentration, reaching a peak at approximately 0.8 M and then decreasing at higher acid concentrations. A similar increase and decrease in metal extraction was observed when the reducing agent was increased. In leaching with tartaric acid, the extraction of cobalt was much higher than that of copper, although extraction of both metals increased with acid concentration. Additions of small amounts of hydrogen peroxide were found to increase cobalt extraction in tartaric acid but had a minimal effect on copper. An increase in the solution temperature had a significant effect in the organic acid environment, with the effect on cobalt extraction being much more pronounced than on copper.

Jan 1, 2014

By X. Yang, G. D. Zhai

The prop is the most important part to ensure the proper functioning of hydraulic support. When the hydraulic support is impacted by the roof, the prop is prone to extrusion deformation, expansion, and even bursting. In order to study the stress on a doubly-telescopic hydraulic support prop under impact load, an impact simulation was carried out based on the drop weight method. First, the impact model of the hydraulic system of the prop was established in AMESim software and the dynamic response curves of the bottom and middle cylinder of the prop obtained. Then, according to the conservation of energy, the pressure formulaes in the hydraulic cylinder of the prop under impact load were derived and verified by the AMESim simulation results, and the maximum pressure on the inner surface of the hydraulic cylinder of the prop obtained. Lastly, the transient dynamic simulation of a hydraulic support prop was carried out in ANSYS Workbench software, and cloud diagrams of stress and deformation of the prop obtained using Workbench simulation. The AMESim simulation process describes the change in fluid pressure in the prop, and the pressure formulae can be used to estimate the internal pressure of the prop under impact load. The finite element analysis results show that the stress of the middle hydraulic cylinder is much greater than that on the bottom hydraulic cylinder under impact load, which can provide a reference for prop design.

Jul 2, 2022

By Y. Wang

Arsenic-bearing acidic effluent from hydrometallurgical processes contains many harmful metal ions and must be appropriately treated before discharge. In the present study, arsenic, copper, zinc, aluminum, and magnesium were co-precipitated by means of the Fenton reaction. The precipitates obtained under different conditions were investigated to determine their stability. The results indicate that pH value and hydrogen peroxide (H2O2) dosage have significant effects on the removal of various elements. Arsenic, copper, zinc, and aluminum (but not magnesium) can be removed at pH 5–6 and anH2O2/As mole ratio of 2 at ambient temperature. The precipitates were mainly amorphous and granular with particle size in the micrometre range. The arsenic concentration in leachate from the toxicity characteristic leaching test was 3.6 mg/L, which proves that the precipitates are effective in fixing arsenic.

Aug 3, 2023

By M. -B. Kime

This study applies attainable region analysis to optimise cobalt recovery from oxidised ores via reductive leaching with sulphur dioxide and sulphuric acid. The attainable region framework enables systematic visualisation of trade-offs between cobalt yield and sulphur dioxide loss, guiding reactor network design beyond conventional mass balance modelling. Experimental column leaching trials, supported by validation runs, were conducted under controlled flow and reagent conditions. Kinetic parameters for cobalt dissolution and sulphur dioxide consumption were used to simulate reactor trajectories and construct attainable region envelopes. To ensure hydrodynamic realism, residence time distribution tests confirmed partial plug flow behaviour with dispersion effects, justifying the use of hybrid reactor models in the attainable region simulations. The results revealed that increasing recirculation ratios improves cobalt yield while reducing sulphur dioxide losses, with attainable efficiencies exceeding 90% cobalt recovery and < 20% sulphur dioxide loss. Importantly, the study proposes practical reactor network configurations for future implementation, including staged percolation columns with intermediate mixing zones, oscillatory flow reactors, and modular fluidised bed systems. These designs offer scalable pathways to translate attainable region-based optimisations into industrial practice. Compared to traditional modelling, attainable region analysis provides a geometric decision support tool that captures multi-objective trade-offs and reactor interactions, offering novel insights for continuous leaching system design. This work advances the application of attainable region methodology in minerals engineering by bridging theoretical optimisation with practical reactor design, supporting sustainable cobalt recovery from both primary ores and recycled feedstocks.

Mar 30, 2026

By C. Aldı, O. Yaral

For the more economical excavation of tunnels in underground mining activities, the selection of mechanised excavation machines (such as roadheaders, electro-hydraulic drills, etc.) and the analysis of performance prediction that can be used in estimating machine energy consumption have been subjects of research from past to present. One of the parameters to be considered in studies examining these methods, is the grinding process. The success of increasing efficiency in grinding is expressed by a reduction in energy consumption. The goal of a grinding process is to maximise the grinding amount at the appropriate grinding size while minimising the energy consumption per tonne of the fragmented material. Today, the depletion of high-grade ore deposits has largely directed the mining industry towards low-grade but large reserve ore deposits. This shift has particularly increased the importance of the grinding process, as it is dependent on particle liberation. Grinding is a critical step in reducing the mineral to the appropriate size, and energy consumption poses a significant challenge in this process. As a result, researchers have conducted various studies focusing on energy efficiency and cost optimisation in this field. In this study, the grindability of 7 different coal environment rocks (sandstone, siltstone) from the Zonguldak Basin, Uzulmez Region was investigated. For this, Hardgrove Grindability Index and Bond Work Index tests were conducted. While determining the relationships between grindability and other parameters, the results obtained from the Hardgrove Grindability Index (HGI) test were used. The energy values found in the Bond Work Index (BWI) test were used to evaluate the excavatability of the rocks. Additionally, tests for strength, hardness, drillability, and abrasiveness were conducted to observe the impact of other parameters on grindability. Considering the results obtained from the experiments, significant relationships were found between the grindability of the rocks and other parameters.

Mar 30, 2026

By F. M. L. Mulaudzi

Metal dusting is a corrosion phenomenon that occurs in strongly carburizing gas atmospheres at elevated temperatures. Reaction kinetics and product characterizations of Alloys 602CA and 800 were examined by scanning electron microscopy with energy dispersive X-ray analysis (SEM-EDX) and X-ray diffraction (XRD).The results showed that Alloy 602CA is more resistant to metal dusting than Alloy 800. Visual examination and SEM surface analysis showed that Alloy 800 suffered metal dusting attack after a relatively short exposure period. The amount of coke deposits increased on Alloy 800 with increased exposure from 96 to 336 hours. X-ray diffraction on the reacted surfaces identified graphite and austenite in both alloys and some iron oxides/spinel for Alloy 800.

Jan 1, 2012

By D. F. Malan, T. E. Oates

A recent experimental pillar extraction project at a UG2 bord-and-pillar mine presented a unique opportunity to compile a new pillar database. Currently, the South African hard rock bordand- pillar mines are designed using the Hedley and Grant formula with a modified K-value. This empirically derived formula was developed for uranium mines in the Elliot Lake district of Canada. The use of this formula for the design of pillars in South Africa is questionable. Very few pillar failures have nevertheless been observed and its current calibrations for the various reef types are possibly too conservative. A new UG2 pillar database of 66 pillars, of which seven are classified as failed, was compiled by the authors. This enabled a revised ‘first-order’ calibration of the K-value for the Hedley and Grant formula. The new estimated value for the UG2 is K = 75 MPa. This gives a pillar strength that is more conservative than the PlatMine formula. This work should nevertheless be considered as only a preliminary calibration as the database was small. Further work is also required to determine whether the exponents in the formula for the width and height parameters are appropriate for UG2 pillars.

May 3, 2023

By L. Zhou, J. Qiu, M. Tang, J. Wang, G. Dai

Coal spontaneous combustion in longwall gobs is a major concern in coal mines. In comparison to other hazards, this phenomenon is difficult to detect. Fifteen factors influencing coal spontaneous combustion in longwall gobs were identified from the literature. The logical relationships between these factors were evaluated and quantified by decision-making trial and evaluation laboratory (DEMATEL) and interpretive structural modelling (ISM) methods. A four-level hierarchical structure model was established. The research shows that combining DEMATEL and ISM can reveal the key factors that influence coal spontaneous combustion in longwall gobs and establishthe interactions and relationships among these factors. The results can provide the basis for preventing and controlling coal spontaneous combustion in longwall gobs.

Jun 10, 2024

By Turgay Gurun

"Digital simulation can be used as an analytical tool to optimize the design of crushing plants without need for large-scale experimental programs.General mathematical description of a crushing operation permits the simulation of a crushing plant flowsheet under various operating conditions. The process model encompasses multistage open- and closed-circuit crushing of hard and soft rock. Crushing balances are analyzed in the light of crusher and screen performance and a comparison of different closed-circuit arrangements is made in terms of process and layout criteria.The simulation model allows comparison of process alternatives to be made in terms of equipment selection and capital and operating cost estimation. It thus provides the pertinent practical information to maximize plant efficiency, and to minimize expenditures in such items as equipment, structures, power consumption, and so on."

Jan 1, 2014

By F. P. Janse van Rensburg, P. J. Le Roux

"There are numerous factors that affect open stope stability and often result in falls of ground. These falls of ground can be attributed to factors such as beam failure due to a larger than normal roof area (hydraulic radius too large), adverse ground conditions, seismicity, the stress-strain environment, absence of support, and poor drill-and-blast practices. The effect of time on the stability of open stopes is sometimes underestimated and is relatively unknown, especially on Target Mine. Actual data was collected from open stopes at Target and analysed to show the effect of time on open stope stability. The benefits of this analysis will include improved understanding of time-dependent failure, which can assist in reducing dilution and the risk of sterilization of future mining blocks. IntroductionTarget Mine is situated adjacent to the town of Allanridge, some 20 km from Welkom in South Africa’s Free State Province, and is the most northerly mine in the Welkom Goldfields area (Figure 1). The mine consists of a single surface shaft system with a sub-shaft (Target 1C shaft) and a decline. Ownership was attained by Harmony Gold Mining Company Limited in May 2004 (Harmony Gold Mining Company Limited, 2010). Before discussing the selection of open stopes for the back-analyses, a brief explanation of open stoping as practiced at Target Mine will be given. The orebody is some 180 m in thickness and 270 m wide and comprises multiple reefs overlying one another. The 180 m thick reef package is termed the Eldorado Reefs, as shown in Figure 2. The Eldorado Reefs suboutcrop against the Dreyerskuil Reefs, as shown in Figure 3. The dip of the reef varies from as low as 10° in the west to 75° in the east.Compared with most Australian and Canadian open stoping mining operations, Target Mine is unique. In most Australian and Canadian mining operations the hangingwall and footwall of the open stopes comprise waste rock, and the orebody dips relatively steeply. Due to the depth of Target Mine, some 2300 m to 2500 m below surface, a destress slot (Figure 4) is mined to create an artificial, shallow mining environment whereby the field stress is managed and kept at values of around 60 MPa. The destress slot comprises a narrow tabular stope with an average width of 1.5 m, and is mined on the Dreyerskuil Reefs.At Target Mine the hangingwall, sidewalls, and footwall of the open stopes all comprise reef of different grades, except for the EA1, where the EB footwall is waste rock. If a stope, for example, is mined alongside an existing old stope, the western sidewall of this stope will consist of backfill. The general mining direction of open stopes is from the lowest position of the reef on the west, progressing up towards the east as shown in Figure 5."

Apr 1, 2019