Search Documents

By Y. M. Zhao

The separating performance of a pilot dry beneficiation system using a gas-solid fluidized bed was investigated with coal from South Africa. The coal used for the study has a low inherent moisture content, a moderate ash content, a moderate volatile content, a low sulphur content and a high calorific value. Its washability is moderate. Experimental results show that the separating quality of the fluidized bed drops gradually as the feed-coal particle size decreases. The probable error, E, values for 50?25mm, 25?13 mm and 13?6 mm coals were 0.04 g/cm3, 0.06 g/cm3 and 0.09 g/cm3, respectively. The cause of the differences in separating characteristics was analysed by particle dynamics and numerical modelling. Furthermore, the pilot fluidized bed was employed to separate 50-6mm coal. In this experiment the coal ash content was reduced from 23.74% to 11.79%, with a probable error, E, value of 0.07 g/cm3and a recovery efficiency of 98.26%. This indicates that the fluidized bed is applicable to the separation of coal from South Africa and has good separating performance and wide applicability. Keywords: feed-coal particle size; gas-solid fluidized bed; dry coal beneficiation; numerical simulation.

Jan 1, 2010

By R. Shen

This paper presents results of a feasibility study of recycling manganese furnace dust generated in production of ferromanganese and silicomanganese at Tasmanian Electrometallurgical Company, Australia. Dried manganese furnace dust contains about 20 wt% of carbon, in average 33.4 wt% of manganese and 1.3 wt% of zinc. Manganese in the dust is in the form of MnO, Mn3O4 and MnCO3; zinc is mainly in the form of ZnO andZnSO4. Analysis of the zinc balance with dust recycling showed that to keep zinc intake at the acceptable level, it should be partly removed from the dust. In the reduction laboratory experiments, zinc oxide was reduced to zinc vapour by tar of the dust. Reduction of zinc oxide started at 800°C and zinc removal rate increased with increasing temperature; removal of zinc was close to completion at 1100oC. Optimal conditions for removing zinc from the dust include temperature in the range 1000-1150°C, inert gas atmosphere and furnace dust fraction in the furnace dust-manganese ore mixture above 60%. In the sintering of manganese ore with addition of manganese dust in the sintering pot, zinc was reoxidised and deposited in the sinter bed. Removal of zinc in the sintering pot tests was in the range 4-17%. Up to 30% zinc removal was achieved from the bottom layer of the sinter bed. It can be concluded that zinc removal will be low during the processing of manganese furnace dust in the sinter plant. The zinc removal rate will be the highest when pelletised manganese furnace dust is added to the bottom layer of the sintering bed.

Jan 1, 2007

By P. H. S. W. Kulatilake, B. Malama

To simulate brittle rocks, a mixture of glastone, sand and water was used as a model material. Thin galvanized sheets were used to create joints in blocks made out of the model material. To investigate the failure modes and strength, both the intact material blocks as well as jointed model material blocks of size 35.6 × 17.8 × 2.5 cm having different joint geometry configurations were subjected to uniaxial and biaxial compressive loadings. Results obtained from the intact model material blocks are used to validate a new intact rock failure criterion for biaxial loading. Results obtained from both the intact and jointed model material blocks are used to develop a strongly non-linear new rock mass failure criterion for biaxial loading. In this failure criterion, the fracture tensor component is used to incorporate the directional effect of fracture geometry system on jointed block strength. The failure criterion shows the important role the intermediate principal stress plays on rock mass strength. Zur Simulation spröder Gesteinsarten wurde ein Modellmaterial aus Dentalgips, Sand und Wasser hergestellt. Daraus wurden Blöcke gegossen, in denen mittels dünnen, galvanisierten Blechen Trennflächen erzeugt wurden. Die Blöcke mit Abmessungen von 35.6 × 17.8 × 2.5 cm wurden in einaxialen und biaxialen Druckversuchen belastet. Es wurde das Versagensverhalten und die Festigkeit von intakten Blöcken sowie durchtrennten Blöcken mit unterschiedlicher Trennflächengeometrie untersucht. Aus den Ergebnissen der Versuche an intaktem Material wurde ein neues Versagenskriterium für biaxiale Belastungen validiert. Die Ergebnisse der Versuche an intakten und durchtrennten Blöcken wurden verwendet, um ein neues stark nicht-lineares Versagenskriterium für geklüftetes Gebirge unter biaxialer Belastung abzuleiten. Darin wird der Bruchtensor verwendet, um den Einfluss der Trennflächengeometrie auf die Festigkeit zu erfassen. Das Versagenskriterium stellt heraus, welche Bedeutung die mittlere Hauptspannung für die Gebirgsfestigkeit hat. Un mélange de platre dentaire, de sable et d’eau a été utilisé pour développer un matériau analogue des roches fragiles. De fines feuilles galvanisées permettent de créer des discontinuités représentatives des discontinuités naturelles dans des bloques fabriqués avec ce matériau analogue. Les modes de rupture et la résistance, tant pour le matériau intact que pour le matériau avec ses discontinuités, ont été étudiés sur des blocs de 35.6 × 17.8 × 2.5 cm soumis à des efforts de compression uniaxiaux et biaxiaux. Différentes configurations de géométrie de discontinuités ont été considérées. Les résultats obtenus à partir des blocs intacts permettent de vérifier un nouveau critère de rupture pour les roches intactes soumises à des efforts biaxiaux. Les résultats obtenus, tant avec les blocs intacts qu’avec les blocs avec discontinuités, sont utilisés pour développer un nouveau critère de rupture, fortement non linéaire, pour les massifs rocheux soumis à des chargements biaxiaux. Dans ce critère de rupture, un tenseur de fractures est introduit pour caractériser les effets directionnels de la géométrie des systèmes de discontinuité sur la résistance des blocs avec discontinuités. Ce critère de rupture démontre le rôle important de la contrainte principale intermédiaire sur la résistance des massifs rocheux.

Jan 1, 2003

By A. Haque

The shear behaviour of infilled joints produced from ordinary gypsum plaster (gyprock) and bentonite was investigated in the laboratory under Constant Normal Stiffness (CNS) conditions. Shear tests were performed on saw-tooth profiles having Joint Roughness Coefficients (JRC) of 4.75 and 9.25 under an initial normal stress (sno) of 0.30 to 1.10 MPa, and at a normal stiffness (kn) of 8.5 kN/mm. Test data under the same sno and infill thickness to asperity height ratio (t/a) were analysed for two different sets of JRC. The peak shear stress plotted against the t/a ratio under constant sno revealed an increase in peak shear stress with the increase in JRC, up to a t/a ratio of about unity. The effect of roughness on the peak shear stress was observed to be minimal when the t/a ratio exceeded 1.40. A mathematical model for the prediction of peak shear stress due to the increased infill thickness has been developed based on a hyperbolic stress-strain relationship and energy balance principles. The model predictions are in good agreement with the laboratory observations. Le comportement de cisaillement des joints remplis produits à partir de plâtre ordinaire et de bentonite a été étudié dans le laboratoire sous des conditions de rigidité normales constantes. Des essais de cisaillement ont été réalisés sur des profils en dents de scie ayant des coefficients de rugosité des joints (CRJ) variant de 4,75 à 9,25 sous un effort normal initial (sno) de 0,30 à 1,10 MPa, et une rigidité normale (kn) de 8,5 kN/mm. Le résultat des essais conduits sous la même contrainte et épaisseur de remplissage au rapport aspérité/hauteur (t/a) ont été analysés pour deux ensembles différents de CRJ. La variation de l'effort de cisaillement maximal contre le rapport t/a sous une contrainte normale constante a indiqué une augmentation de l'effort de cisaillement maximal avec l'augmentation du CRJ, jusqu'à un rapport de t/a proche de l'unité. L'effet de la rugosité sur l'effort de cisaillement maximal a été minimal quand le rapport t/a a excédé 1,40. Un modèle mathématique pour la prévision de l'effort de cisaillement maximal dû à l'épaisseur accrue du remplissage des joints a été développé sur la base de la variation entre contraintes hyperboliques et déformation et sur des principes de bilan énergétique. Les prévisions du modèle sont en bon accord avec les observations de laboratoire. Das Scherverhalten in mit gewöhnlichem Gips und Bentonit gefüllten Klüften wurde im Labor unter Bedingungen konstanter Normalsteifheit (CNS) untersucht. Scherversuche wurden durchgefürt für Sägezahnprofile mit Werten des Fugenrauhigkeitskoeffizienten (JRC) von 4.75 und 9.25 unter Normalspannungs-werten (sno) von 0.30 bis 1.10 MPa, und bei Normalsteifheit (kn) von 8.5 kN/mm. Testresultate für gleiche Werte von sno und Verhältnis Fülldicke zu Rauhigkeit (t/a) wurden untersucht für zwei verschiedene Werte von JRC. Die Beziehung zwischen maximaler Schubspannung und und t/a Verhältnis unter konstantem sno zeigte einen Anstieg der maximalen Schubspannung mit zunehmendem JRC, bis zu einem t/a Verhältnis von etwa 1.0. Der Einfluss der Rauhigkeit auf den Maximalwert der Schubspannung war minimal solange das t/a Verhältnis den Wert von 1.40 überstieg. Ein mathematisches Modell wurde entwickelt für die Vorhersage der Schubspannung die von zusätzlicher Fülldicke erwartet werden kann, ausgehend von einer hyperbolischen Spannungs-Dehnung Beziehung und dem Energiegleichgewichts-prinzip. Die Modellvorhersagen zeigten gute Uebereinstimmung mit den Laborbeobachtungen.

Jan 1, 2003

By A. McKenzie

During the late 1990s Anglo American PLC was evaluating the Gamsberg zinc deposit in the Northern Cape Province. As the primary South African metallurgical technology provider, Mintek became involved in the evaluation of a pyrometallurgical process for the recovery of zinc from the Gamsberg deposit. eloping DC arc furnace technology for the metallurgical industry. This includes the patented Enviroplas® process for the treatment of zinc bearing waste materials. As a consequence Mintek has developed extensive expertise in the pyrometallurgical processing of zinc bearing materials. However, Mintek?s technologies stopped with the production of Prime Western Grade (PWG) zinc. Early on in the evaluation of the Gamsberg project, it became evident that the refining of PWG zinc would play an important part in the economic viability of the project. At the time the only pyrometallurgical technology available for the refining of PWG zinc to Special High Grade (SHG) zinc was the New Jersey process. This process represents 50-year-old technology and has not undergone significant refinement since the technology was developed. In order to provide a complete pyrometallurgical flow sheet for possible implementation at Gamsberg, Mintek assessed the New Jersey process with a view to either improving the technology or developing a new technology appropriate to the 21 century. In 1998 Mintek convened a consortium consisting of Mintek, the University of Cape Town, Eskom Enterprises, Bateman Metals and Anglo American PLC. The consortium successfully applied to the Innovation Fund for funding to develop a new process for the pyrometallurgical refining of PWG zinc to SHG zinc. The main aims of the project were to develop a new technology for pyrometallurgical zinc refining that conformed to the following: ?Decrease the production cost of SHG zinc metal to stimulate the development of the Gamsberg deposit. ?Be compatible with the current Enviroplas® process, preferably as an add-on to that process. ?Should use electrical energy to benefit from local price tariffs. The project commenced at the beginning of 2000 and consisted of three phases: ?an initial technology search and assessment of the fundamental aspects of zinc distillation. ?the design of a pilot plant for zinc refining. ?the manufacture, commissioning and operation of the pilot plant. A new technology based on a DC arc boiler feeding a packed distillation column was developed and during 2003 the project culminated in the successful operation of a 200 kg/h pilot plant. Ultimately, all of the aims of the project were met and the main outcome is that an advanced process for the pyrometallurgical refining of zinc (the Zincref process) has been developed. The main innovation of the technology was the switch from an energy transfer limited process to a mass transfer limited process (for which a patent has been registered).

Jan 1, 2004

By A. T. van Zyl, M. Mthenjane, M. J. Cole

Growing global concern over the impacts of climate change, attributable largely to fossil fuel energy sources, has led to the widely shared goal for a ‘just transition’ to cleaner energy and reduced dependence on carbon-based fuels. As the world’s 14th biggest CO2 emitter and being particularly vulnerable to the impacts of climate change, South Africa must embark on a just transition pathway. This paper reviews expected coal mine closures and associated community vulnerabilities and local governance challenges in South Africa. Decommissioning schedules for all coal-fired power stations and operating coal mines are plotted, and 69 mining host communities and 21 municipalities are mapped, classified, and described. Community socio-economic profiles are measured using a set of SDG indicators and census data and municipalities assessed through financial audits. Our research shows that five coal-fired power plants (8.9 GW) and 15 coal mines (29.5 Mt/a) will probably close by 2030, and a further four plants (14 GW) and 23 mines (106 Mt/a) by 2040. Thus, the shift to cleaner energy will likely occur without the premature closures implied by the just transition. The impact of mine closure on the 2.5 million residents of host communities will be significant, particularly as levels of income, employment, and education are already very low and many municipalities are in financial distress. The South African approach to the just transition needs to take local realities into account and the narrative must support an effective transition that does not undermine energy security and economic growth.

Jun 5, 2023

By H. Yilmaz

Tensile strength testing has been one of the most common physical property testing methods of thin spray-on liner (TSL) products worldwide. However, the variety of products tested has been insufficient for comparison purposes. Specimen preparation procedures and test parameters such as curing time and loading rate are not reported well. Comprehensive tensile strength testing on 20TSL products and one plain shotcrete brand was performed over 28days of curing period. Detailed information on the test procedures with particular attention on the important aspects during sample preparation and test execution are provided. As expected, the tensile strength increases with increasing curing period. The test results make the categorization and comparison of liner products possible.

Jan 1, 2010

By I. Satola, J. Aromaa

In this work we have reviewed methods to classify corrosivity of ground waters. Weight loss and stress corrosion cracking (SCC) corrosion tests have been done for rebar and steel strand. No clear indication of SCC was found. The application of tensile stress to 85 % of yield strength increased general corrosion rate significantly in very corrosive waters. The effect of corrosion protection on the axial behavior of steel strands was determined by double pipe axial tests with different embedment lengths. The results showed a significant difference on behavior between epoxy-coated steel strands, galvanized steel strands and plain steel strand. Dans la présente étude, nous avons passé en revue des méthodes permettant de classifier la corrosivité des eaux souterraines. Des tests portant sur les pertes de poids et sur la corrosion FCC (la fissuration par corrosion sous contrainte) ont été effectués pour les barres d’armature et les torons. Aucune indication nette de FCC n’a été constatée. L’application d’une contrainte de traction allant jusqu’à 85 % de la limite d’élasticité a accru de manière significative la vitesse générale de corrosion dans les eaux très corrosives. L’effet de la protection contre la corrosion sur le comportement axial des torons en acier a été déterminé au moyen de tests axiaux à double tube avec des longueurs d’enrobage différentes. Les résultats ont mis en évidence une différence significative quant au comportement entre les torons en acier à revêtement époxy, les torons en acier galvanisés et les torons en acier standard. In dieser Arbeit haben wir Methoden geprüft, die korrosive Wirkung des Grundwassers einstufen. Gewichtsverlust- und SCC-Korrosionstests wurden für Stahlstäbe und Drahtlitzen durchgeführt. Es wurden keine sicheren Hinweise auf Spannungsrisskorrosionsbrüche gefunden. Bei Anwendung einer Dehnbelastung von 85 % der Streckspannung bzw.Ergebnisstärke stieg die allgemeine Korrosionsrate in stark korrosivem Wasser deutlich an. Die Wirkung des Korrosionschutzes bei axialem Verhalten von Stahldrahtlitzen wurde durch axiale Tests an Doppelleitungen unterschiedlicher Versenkungslänge determiniert. Die Ergebnisse zeigten im direkten Vergleich von epoxidbeschichteten, galvanisierten und normalen Stahldrahtlitzen beachtliche Unterschiede im Verhalten auf.

Jan 1, 2003

By S. Mudau, P. Mohasoa, M. J. Cole

Derelict and ownerless (D&O) mines in South Africa have been an ongoing concern for over a decade. While some progress has been made to rehabilitate D&O asbestos sites, significant work remains, exacerbated by the growth in illegal mining. There are concerns regarding the accuracy and transparency of the D&O database, lack of oversight, and constrained funding, and the government is increasingly looking to the private sector to fund rehabilitation. Given these challenges, a new, sustainable approach to D&O sites in South Africa is needed to bring clarity and transparency to the process, recognise responsibilities and promote partnerships, and explore economic opportunities at D&O sites to reduce the financial liability and respond to the growing demand for critical minerals. This article has three components: i) reviews of international D&O good practices; ii) it analyses South Africa’s current approach and the D&O sites; and iii) proposes a D&O framework that addresses data, risk ratings, responsibilities and rehabilitation, economic opportunities, and stakeholder engagement. The study finds that the majority of the 6,100 so-called abandoned D&O mines are quarries and mine site features, 16% are operational, at least 11% have owners, and only 752 (12%) require rehabilitation. The framework aims to bring clarity and fairness to decision-making and to assign risk and responsibility for rehabilitation and seeks to incorporate economic opportunities to reduce the financial burden of rehabilitation, create jobs for local communities, and respond to the growing demand for critical minerals for the clean energy transition.

Apr 25, 2025

By F. Dehghani

The influence of different grinding methods on the shape characteristics of magnetite particles was investigated. Also, the effect of particle shape on the flotation of the magnetite, both alone and in the presence of quartz particles, was investigated. The shape characteristics of the magnetite particles were measured and calculated from images obtained by scanning electron microscopy via an image analysis system. The flotation tests were performed using a laboratory flotation cell. Results showed that in the -250+212 µm and -106+75 µm size fractions, ball mill products have a higher elongation value than rod mill products, while in the -150+125 µm size fraction, rod mill products have a higher elongation value. Particles with higher elongation values and lower roundness values have a higher flotation kinetic constant. Furthermore, the influence of magnetite particle shape on flotation is greater, and the flotation kinetic constant is higher, in the presence of quartz particles than in the flotation of magnetite alone Keywords shape, elongation value, flotation kinetics, magnetite.

Dec 1, 2013

By N. M. Skarbøvig

Safety nets have been used selectively in several South African mines over the years. Recently, however, an increased emphasis on mine safety has seen a resurgence of their utilization underground. This renewed interest has, however, also raised questions about the design and performance of these nets and their practical applications underground; these are the subjects of this paper. Generally, mine safety nets are used to protect personnel from falling rock in temporarily supported development ends, tunnels, ASGs and stopes. These diverse applications each require specific net designs, resulting in a wide product range. As a rule, however, mine safety nets need to carry specified static or dynamic loads with the least possible deformation. Because of the application-specific characteristics of mine safety nets, there is no South African national standard for them. Consequently, neither the SABS, nor the CSIR, performs standard tests on these components. In 2007, therefore, SIMRAC made available their Savuka facility for the testing of mine safety nets; the Savuka drop test became the accepted industry test standard for mine safety nets. From late 2007 to mid 2009, Norsenet, in collaboration with SRK Consulting, the designated operators of the site, conducted approximately 200 tests, which formed the core of Norsenet's database of safety net performance under various loading conditions. The test specimens comprised a wide range of net materials and config¬urations; the materials included: high density polyethylene, polypropylene, polyester, nylon, as well as a blend of polyester and polypropylene used primarily for reinforcement ropes. Net configurations encompassed the following parameters: net type, i.e., knotted nets or sewn nets; net strand type, i.e., braids, twines, or webbing; strand size; mesh size; mesh orientation, i.e., parallel or oblique to the net edge; net edge reinforcement, i.e., knotted, tied, with or without reinforcement ropes; internal reinforcement ropes, i.e., diagonal ropes and/or orthogonal ropes; as well as net attachment options, including loops and chainlinks. From the number of variables listed above, and the limited number of tests available, it can be appreciated that the findings of the test series required careful scrutiny. Nevertheless, principal performance factors clearly emerged: besides the obvious net mesh variables, such as net strand material, strand diameter and mesh size, it was the configuration of the reinforcement ropes and their attachment to the net panel which had the strongest influence on net performance. All the structural elements of a safety net need to work together to transfer the imposed load from the net panel, through the reinforcement ropes, to the net attachment points. In this load transference chain, the weakest link limits the strength of the structure. From this development work, Norsenet has gained valuable expertise to custom-design and manufacture nets to clients' specifications. The examples presented in the paper will also show the experience acquired in the installation of nets underground. Future work will include the establishment of a state-of-the-art net testing facility at Norsenet's factory in Vredenburg.. Keywords Mine safety net, safety net, protective device, mine safety, safety net design, safety net performance, safety net applications.

Jan 1, 2011

By G. M. Cresswell

The 2 360 t/h two module Phola coal preparation plant represents anew era of large plant in the Witbank coalfield designed to extend its life to 2020 and beyond. The plant uses the optimum processing model for Witbank coals, receiving a feed coal size of -50 mm, wet screening it into coarse and small coal fractions 50 x12 and 12 x0.63 mm before processing them in parallel through two primary DM cyclone sections, in order to make a 27.5 MJ/kg export floats product. The sinks are processed through a common high density DM cyclone section to produce a 21.5?23 MJ/kg thermal coal middlings product. The plant design incorporates the largest size DMS equipment used to date in South African coal preparation plants, i.e. 1 150 mm large diameter pump fed DM cyclones and 4.2 m width banana screens. The fine coal is conventionally processed by spirals, whereas the raw coal slimes are filtered using automated plate and frame filter presses and added to either the middlings or discards depending on its quality. The paper describes the database, innovative design concepts, construction, and commissioning.

Jan 1, 2010

By H. Gercek, M. Genis

In this paper, the effects of dynamic loads on the geometry of the failure zone occurring around underground openings, excavated in deep and massive rock masses, have been investigated. Following an elasto-plastic stress analysis of a two-dimensional underground opening under static conditions, dynamic loads have been applied. In the static and dynamic analyses, FLAC2D computer program has been utilized. Maximum ground acceleration value is selected as an input parameter. An index determining the relative size of the yield zone around the opening has been used for comparison of instabilities. In diesem Bericht wurden die Auswirkungen von dynamischen Lasten, auf die Geometrie der Bruchzone in der Umgebung von Untertagehohlräumen, die in tiefen und massiven Gebirge aufgefahren wurden, untersucht. Nach einer elasto-plastischen Spannungsanalyse eines zwei-dimensionalen Untertagehohlraumes unter statischen Beanspruchungen, wurden dynamische Lasten aufgebracht. Für die statischen und dynamischen Analysen wurde das FLAC2D Computer Programm verwendet. Die maximale Bodenbeschleunigung wurde als Eingabe Parameter gewählt. Zum Vergleichen der Unstabilitäten wurde ein Index verwendet, der die relative Grösse der Bruchzone in der Umgebung des Hohlraumes bestimmt. Dans ce papier, l’influence des chargements dynamique sur la géométrie de la zone en rupture observée autour des cavités profondes excavées dans des massifs rocheux ont été étudiées. Des chargements dynamiques ont été appliqués, dans le cas d’une modélisation bi-dimensionnelle de l’excavation d’une cavité profonde, sur la base d’une analyse élastoplastiques des contraintes en conditions statiques. Le code de calcul FLAC2D a été utilisé pour les analyses statiques et dynamiques. La valeur maximale de l’accélération du sol est choisie comme paramètre d’entrée. Un indice déterminant la taille relative de la zone sollicitée autour de la cavité a été utilisé pour comparer les différentes instabilités.

Jan 1, 2003

By R. Poisel, C. Scavia, Preh A., W. Roth, M. Pirulli

ABSTRACT: Two methodologies for the three-dimensional simulation of the run out of rock avalanches are presented: one based on a granular approach and the other based on a continuum equivalent approach. An evaluation of the possible run out area of the Oselitzenbach landslide (Carnic Alps, Austria) has been carried out applying the two methodologies. The combined use of these two approaches makes it possible a comprehensive assessment of the run out area. RESUME: Deux méthodologies pour la simulation tridimensionnelle de la propagation des avalanches rocheuses sont présentées: la première est basée sur un modèle de type granulaire et la deuxième sur un modèle du continu équivalent. Une évaluation de la propagation éventuelle de l’avalanche de Oselitzenbach (Alpes Carniche, Autriche) a été réalisée en utilisant les deux méthodologies. Les résultats obtenus montrent que la combinaison des deux approches rend possible une analyse plus complète de la phase de propagation. KURZFASSUNG: Für die dreidimensionale Modellierung eines Felsmassensturzes (sturzstrom) werden zwei Methoden, eine granulare und eine kontinuumsmechanische Methode, vorgestellt. Beide Methoden wurden zur Abschätzung der Ausbreitung (runout) der Massenbewegung Oselitzenbach (Karnische Alpen, Österreich) herangezogen. Die kombinierte Anwendung beider Methoden ermöglichte eine umfassende Beurteilung des möglichen Ausbreitungsbereichs.

Jan 1, 2003

By R. Hope, C. van Heerden

In any process or organization inefficiencies are costly. In times of abundance this reality often does not receive much attention. During such times the focus is rather on increasing capacity to increase production. However, there is a growing awareness in the world of tougher economic, social as well as environmental conditions, and enterprises find themselves facing greater demands for accountability towards shareholders, the environment and the public, as well as growing competition for market share and limited global resources. This reality is no different in ensuring a sustainable mineral sands operation. In order to achieve this, any operation needs to be stripped of all process as well as operational inefficiencies. In this context it has become essential for any Mineral Separation Plant (MSP) to have the necessary process monitoring and control systems in place to continually monitor and optimize the production of on-spec products and maximize operational efficiency and consistency. The MSP Grade Control Solution developed by Crusader Systems and running on top of the CSense platform contributes towards these goals by improving the consistent production of on-grade product. This allows the process to operate closer to the maximum allowable product grade constraint, which in turn maximizes production.

Jan 1, 2003

By H. Krogerus, P. Niemelä, P. Oikarinen

High carbon ferrochromium is produced by carbon reduction. No replacement for carbon as reductant has yet been developed. The reduction creates a considerable amount of CO-gas. In open and semi-closed furnaces the gas is burned when leaving the burden. In closed furnaces the formed gas is sucked out by a fan, washed and utilised as fuel. The formation of carbon monoxide is presented briefly starting from thermodynamic considerations up to solid and liquid state reduction. The volume, composition and energy content of the furnace gas are discussed, focusing on the raw materials and pre-treatment processes of the furnace feed as well as on the process equipment and control. Outokumpu has been using closed and sealed furnaces and utilising the CO-gas in its Tornio Ferrochrome Works since 1968. Today in Tornio with an annual ferrochromium production of 260 000 t CO-gas production is 186 million m3, representing 68 MWh an hour. At the same time the furnace power input is 95MW. About 98 % of the CO-gas is utilised, whereof 30% in the ferrochrome production itself. This paper focuses on the characteristics and utilisation of CO-gas. CO-gas is secondary energy, which on one hand saves primary electric and fossil fuel energy in ferrochromium production and, on the other, replaces other fossil fuels at the adjacent steel works. The characteristics of the fuel, requirements for utilisation as well as health and safety aspects are discussed. Utilisation of the gas has a high impact on the total dust and gaseous emissions and on the energy optimisation at the ferrochromium and steel works.

Jan 1, 2004

By L. A. Thompson, A. J. Linington

"Copper–cobalt extraction is a reagent-intensive process resulting in acid consumption greatly contributing towards production costs, which in the current market conditions curtail profitability. Nanofiltration (NF) membranes have become an attractive approach in the mining and minerals industry for product concentration and reagent recovery based on the ability of the membrane to separate monovalent ions from divalent ions. NF membranes can selectively separate acids from metals and salts allowing acid to be recycled as well as the concentration and purification of product streams. Membrane technology in the field of copper–cobalt processing focusses on the concentration of Cu2+ and Co2+ in the pregnant leach solution, recovery of acid from waste streams to neutralization, recovery of valuable metals from waste ponds and process water recovery. This paper aims to provide insight into the potential applications of NF membranes in copper–cobalt processing circuits as well as a brief overview of the effects of process conditions on membrane performance and process development. INTRODUCTION The copper–cobalt industry commonly uses inorganic acids, such as sulfuric acid, in large quantities for primary leaching of copper–cobalt oxide ores and releaching during product purification (Stuurman et al., 2014). This results in numerous acidic intermediate streams containing high metal concentrations and acidic waste streams with low metal concentrations. Acid consumption typically accounts for 10–15% of the operating costs of mines in the Democratic Republic of Congo (DRC) and Zambia (Acid Plant Database, 2015). Due to remote mine locations, poorly maintained roads and cross-border conflict, the cost of sulphuric acid can range between USD 300 and 400 per ton. The pivotal role of acid in the copper–cobalt extraction process has driven many mines to build sulphuric acid plants on site to ensure a reliable acid supply, however elemental sulphur still needs to be imported which faces similar logistical challenges and contributes towards operating costs."

Jan 1, 2015

By P. Syrjänen, Lovén. P.

Because geostatistics together with block modeling has not been studied in detail before in the rock mechanics, a two-year research program to investigate the practical use of geotechnical modeling was started in Finland in 1999. According to research work results block modeling gives good estimate of overall rock mass quality but it can not identify individual structures like faults and narrow weakness zones. Weakness zones and faults should be mapped from drill cores, surface mapping, geophysical methods etc. and manually generate 3-D structural model. Rock mechanical 3-D modeling can be used for preliminary stope dimensioning and preliminary reinforcement design. Detailed design needs rock quality mapping from drifts during excavation work. La géostatistique associée à la modélisation par blocs n'ayant pas été étudiée en détail jusqu'à présent dans la mécanique des roches, un programme de recherche sur deux ans visant à examiner l'utilisation pratique de la modélisation géotechnique a été lancé en Finlande en 1999. D'après les résultats des travaux de recherche, la modélisation par blocs donne une bonne estimation de la qualité générale de la masse rocheuse mais elle ne permet pas d'identifier les structures individuelles comme les failles et les zones géologiquement dégradées étroites. Ces zones et failles devraient être cartographiées à partir de carottes de sondages, d'une cartographie de surface, de méthodes géophysiques, etc. et générer manuellement un modèle de structure 3D. La modélisation mécanique des roches en 3D peut être utilisée pour un dimensionnement de la chambre et un plan d'armature préliminaires. Un plan détaillé nécessite l'élaboration d'une cartographie de la qualité des roches des galeries lors des travaux d'excavation. Da man früher Geostatik und Block-Modellieren in der Gebirgsmechanik nicht detailliert untersuchte, wurde 1999 in Finnland ein zweijähriges Untersuchungsprogramm in Angriff genommen. Aufgrund der Untersuchungsergebnisse ergibt das Block-Modellieren eine gute Beurteilung der gesamten Gebirgsmassenqualität, kann jedoch einzelne Strukturen wie Verwerfungen und kleine Schwachzonen nicht identifizieren. Schwachzonen und Verwerfungen müssen demnach aus Bohrkernen, oder mit Hilfe von Oberflächenkartierung, geophysischen Verfahren usw. ermittelt und danach ein 3-D-Strukturmodell manuell erstellt werden. Felsmechanisches 3-D-Modellieren ist für die vorbereitende Abbaudimensionierung und für die vorbereitende Bewehrungsplanung verwendbar. Ein detaillierter Entwurf benötigt die Kartierung der Gesteinsqualität aus den Gesteinsstrecken während der Ausbrucharbeiten.

Jan 1, 2003

A wide range of drill holes and process streams are sampled for resource estimation, grade control, and contractual purposes in the minerals industry. However, despite the availability of training courses, conferences and both national and international standards on correct sampling practices, it is still surprising how often little attention is given to ensuring that representative samples are collected for analysis. The reason for this is that the responsibility for sampling is often entrusted to personnel who do not appreciate the significance and importance of sampling, with cost being the main driving force rather than whether the sample is representative of the material from which it was extracted. This seriously undermines the precision and accuracy of the analyses subsequently generated and can render the analysis process a total waste of time and money and expose mining companies to serious, potential, financial losses. Company management needs to reverse this situation and ensure that sampling is given the attention it deserves to generate representative samples for analysis.

Jan 1, 2010

By D. R. Tesarik, F. M. Jones, J. B. Seymour

As part of safety and stability studies at three underground mines in the United States, researchers installed earth pressure cells and embedment strain gauges in cemented rockfill to measure stress and strain changes as mining progressed and the rockfill was loaded. Data from these instruments were used to calculate the in situ modulus of the rockfill for two of the mines. A three-dimensional numerical model of a cemented rockfill cap was validated with data from extensometers anchored in the mine roof and sill; this model was then used to estimate deformation modulus at the third mine because the earth pressure cells and embedment strain gauges recorded negligible changes. Rockfill binder used at these mines ranged from 4 to 8 per cent of the dry components by weight, the water-to-cement ratio was from 0.42 to1.0, and the largest aggregate size in the three mixes ranged from 5 to12 cm (2 to 4.7 in). The range of the calculated in situ deformation modulus values was large, but as expected, it was bracketed by modulus values for cemented tailings and roller-compacted concrete with similar cement contents and water-to-cement ratios. Dans le cadre d’études sur la sécurité et la stabilité de trois mines souterraines situées aux États-Unis, les chercheurs ont installé des palpeurs de pression des terres et des extensomètres d’encastrement dans les remblais cimentés afin de mesurer les variations relatives à l’effort et à la déformation des terrains durant l’exploitation minière et le chargement du remblai. Les données recueillies à l’aide de ces instruments ont servi au calcul du module in situ du remblai dans deux de ces mines. Le modèle numérique tridimensionnel de la semelle d’un remblai cimenté a été validé à partir des données recueillies par les extensomètres ancrés dans la voûte et dans la semelle de ces mines; ce modèle a ensuite été utilisé pour estimer le module de déformation à la troisième mine, étant donné que les palpeurs de pression des terres et les tensiomètres enfouis avaient relevés des variations négligeables. La matière d’agrégation de l’enrochement utilisée dans ces mines comportait entre 4 % et 8 % des composantes sèches par poids; le rapport eau-ciment se situait entre 0,42 et 1,0; et la taille des agrégats les plus gros dans ces trois mélanges était de 5 cm à 12 cm (2 po à 4,7 po). L’écart entre les valeurs calculées des modules de déformation in situ était grand, mais comme on s’y attendait, cet écart a été compensé par les valeurs modulaires des résidus cimentés et du béton tassé au rouleau avec des teneurs en ciment et des rapports eau-ciment semblables. Als Teil der Sicherheits- und Stabilitätsstudien an drei Bergwerken in den Vereinigten Staaten von Amerika installierten Forscher Erddruckgeber und Einbindungsdehnungsmesser in zementierter Steinschüttung, um Spannungs- und Dehnungsveränderungen während der fortlaufenden Bergarbeiten und der Belastung der Steinschüttung zu messen. Daten von diesen Instrumenten wurden dazu verwendet, das In-Situ-Modul der Steinschüt-ung für zwei Gruben zu berechnen. Ein dreidimensionales numerisches Modell einer zementierten Steinschüttungsschwelle wurde mit den Daten von den im Grubendach und in der Schwelle verankerten Extensometern validiert; dieses Modell wurde dann dazu eingesetzt, um das Deformationsmodul in der dritten Grube zu schätzen, da die Erddruckgeber und Einbindungsdehnungsmesser nur geringfügige Messabweichungen feststellten. Das in diesen Gruben verwendete Steinschüttungsbindemittel variierte zwischen vier und acht Prozent an Trockenkomponenten nach Gewicht, der Wasser-Zementfaktor betrug zwischen 0,42 und 1,0 und die größte Zuschlagstoff-größe in den drei Mischungen schwankte zwischen fünf und zwölf Zentimetern. Die Reichweite der berechneten Werte des In-Situ-Deformationsmoduls fiel etwas breit aus, aber es fand erwartungsgemäß eine Klammerung der Modulwerte zwischen den Zemen-trückständen und dem durch Walzen verdichteten Beton mit ähnlichem Zementanteil und Wasser-Zementfaktor statt.

Jan 1, 2003