Search Documents

By D. J. Griffiths

Beyond doubt it is practically impossible to eliminate all chances of accidents from falls. Mother Earth is not going to give up her treasures without some sacrificing on our part. This particular question ranks among the important subjects connected with coal-mining, and has been given less attention as a factor of life- and limb-destroyer than any other cause. The single fatalities which happen create very little attention; nevertheless, when counted up at the end of the year, they outnumber the unfortunate ones that are mowed down by the wholesale by mine explosions. Fire-damp and coal dust were often considered the greatest evils in coal-mining. All records, however, prove this conclusion to be wrong. The second annual report of the Bureau of Mines gives the loss of life caused by falls of coal and roof in 1910 as 1,310, and in 1911 as 1,321. The reports of Pennsylvania mine inspectors for a period of thirty-three years show that 59.38 per cent of all the accidents underground were caused by falls of roof and coal. Also, the Bureau of Mines shows in its last issue on fatalities that accidents from fall of roof and coal killed more men than any other two causes combined, and that they account for more than half of the deaths under- ground. It seems we are getting too accustomed, taking too many things for granted, running too many risks, trusting too much for the best, and preparing too little for the worst. We must remove the cause; then the effects will cease. However, I can see that a better day is here. The main damaging factors underground are falls of roof and sides. A bad roof is tender and lacks the adhesive qualities to sustain its own weight over comparatively small areas. A roof of any character which is frequently penetrated by well-defined slips and cleats, is characterized as a treacherous roof. The carelessness of men has been one of the main causes of most of the accidents in mining as well as in any other industries. Three Grades of Miners Miners can be classified into three distinct grades, to-wit: the experienced and careful, the experienced and reckless, and the inexperienced. The accidents which the first class usually meet with occur through the carelessness of their co-workers, as well as through accidents which are termed unforeseen, such as falling roof between timbers, and between the timbers and the face of the coal. This may have 'previously given evidence of being absolutely sound and safe, but be released by invisible slips or by sudden outburst of occluded gases in large quantities, as we term big blowers or feeders,

Jan 1, 1913

By D. A. Stout

The Rouse Mine, belonging to the Colorado Fuel & Iron Company, earlier known as the Santa Clara Mine, is located at Rouse, Huerfano County, Colorado. Operations at this property started about the year 1899, after the old Rouse mine had been drowned out by a large flow of water coming from the strata underlying the Cameron seam. The present new Rouse mine was opened by a slope on what is familiarly known as the Walsen seam in the Walsenburg district. This slope has an average grade of 12 per cent bearing approximately, south 45 degrees west, and having at the present time a total length of 6300 feet. This seam has an average thickness at that property of five and one-half feet; however, there are sections of the mine where the thickness is from seven to eight feet. The mine has been developed. since the time it was opened on what is known as the Room and Pillar system ; water level entries have been driven right and left off the slope, and in some cases the rooms are driven directly up the pitch; and in other cases entries have been driven with rooms turned on water level courses. The first flow of water of which we have ally record was encountered in 1901 in what was called the "Second West Entry." This flow, however, was small, and did not require the installation of any large pump unit. From 1901 up until 1909 the flow increased normally as the field was developed. In January, 1909, the first large inflow occurred, coming from a break in the seventh west entry, making a total flow at that time of about 500 gallons per minute. This necessitated putting in larger pumps, and the first pump to be installed of the centrifugal type was a 600 gallon Worthington. By the year 1911 the water had increased, due to additional development, until it was found necessary to install an additional 600 gallon Worthington centrifugal type pump. In December, 1912, a break occurred in the eighth west entry, between the fourth and sixth cross entries, making 2000 gallons per minute. This flow decreased after a period of three weeks some 500 gallons, but on account of the quantity of water then being handled at the mine, and in view of the fact that we needed some reserve pumping equipment to take care of these flows, and additional 600-gallon Worthington centrifugal type pump was installed in June, 1913. An the latter part of 1914 a 250 gallon Reese roturbo was installed to take care of the water, which was being made in the lower workings of the slope. We found after the installation of the centrifugal pumps that the water decreased to a certain degree in the uppermost workings. This led us to believe that the field was being drained, more or less, and the head reduced ; however, our ideas in regard to this were again upset in December, 1915, when we encountered a flow in room 6 off the first cross entry on the ninth east entry. This flow was not as large as previous flows had been, but made 200 gallons per minute.

Jan 1, 1921

The Morning Session of the Forty-Eighth Meeting of the Rocky. Mountain Coal Mining Institute convened in the Little Theater of the Broadmoor Hotel, Colorado Springs, Colorado, at 9:30 a.m., June 3, 1952, Howard B. Crandell, President, presiding. PRESIDENT CRANDELL: Gentlemen, the meeting will come to order, and I would like to introduce to you your Chairman of this meeting, Mr. John B. Hughes, General Manager of the Union" Pacific Coal Company, Rock Springs... (Applause) CHAIRMAN HUGHES: From the activities around last night, I supposed there would be quite a few that would be unable to attend this morning. I am sorry there are not more here because I am sure we have some interesting papers. First on the program this morning is, The Effect of Continuous Mining on Today's. Coal Industry by Mr. William Wearly, Vice President of the Joy Manufacturing Company. Mr. Wearly: (Applause)

Jan 1, 1952

By D. A. Stout

Mr. Chairman and Members of the Rocky Mountain Coal Mining Institute: Your Secretary has asked me to write upon a subject' which is a most interesting one, and which has a very wide scope. In view of the great need for further decreasing costs at its coal mines, the Colorado Fuel and Iron Company began early in 1924 to experiment with methods of mining which had not previously been. tried out at its mines, and which were selected because of the greater possibilities for the concentration of the work, better grouping of workmen, and increased tonnage per workman, with a resultant increased efficiency, better supervision, and lowered costs. Because of the great competition of the day, means and methods must be provided by which fewer mines can be made to produce larger tonnages and at a lower cost. Western physical conditions are such as to make our problems far more complicated and not so easy of solution as compared to many of the eastern fields where conditions are more favorable for the operation of the mines. The dry condition of our Western mines on account of a relatively low humidity, and with additional gaseous conditions, makes the problem still more difficult to solve. A study of new methods was necessary before adoption, and this was particularly true of the method of extracting the coal. Where mechanical means are used, particularly in the coking coal mines of this state, due consideration must be given to the type, and machines or conveyors should not be installed solely on the basis of their performance elsewhere, without the knowledge of local influencing factors. In trying out the newer methods of extraction at our mines, very careful consideration has been given to the question of safety and the adoption of any new methods must provide adequate means of protection to employes, and be approved by' the State Coal Mine Inspector. In any large industry there are a few outstanding operating costs, and usually the leading ones in their order are labor cost, material cost, and power cost. The things which we, hope to accomplish: 1. Reduce labor costs. 2. Reduce material costs. 3. Reduce power costs by the con 4. Reduce the amount of powder used per ton of coal produced. 5. Increase the lump percentage (particularly at the domestic mines). 6. Reduce accidents and annual compensation payment. 7. Reduce haulage costs. 8. Reduce cost for track work. 9. Reduce cost for timber and timbering, and increase the recovery of timber at a considerable additional saving. 10. Reduce the brushing costs. 11. Reduce the amount of rock hauled to the outside. 12. Reduce the cost for drainage. 13. Reduce the cost for ventilating. 14. Reduce cost of inspection and supervision. 15. Reduce the cost for shot firing. 16. Reduction of number of working places. 17. Grouping of men with increased sociability. 18. Increased tonnage per man. 19. Reduction in total number men employed. In the consideration of the methods used and now working successfully, there were three points which were considered outstanding, to make them wholly successful: ventilation, roof control, and transportation. For making the experiments, those mines were selected where conditions

Jan 1, 1925

By O .. G. Sharrer

Loading mechanically has of late become the most widely discussed subject in connection with coal mining and has even equalled. the discussion of safety measures as a topic of interest. The subject has been discussed in the various mining journals and by well. informed persons at the Mining Institutes, so it would appear; that all has been said that can be said until further experiments bring out new lines of discussion. It is, therefore, not the intention to present this article as a technical discussion of the subject of mechanical loading as a whole, but rather as a plain talk on machines with which the writer has had personal contact. In 1919, during the first period of post-war depression, a Pennsylvania coal company employing union labor became interested in the possibilities of mechanical loading with the hope of reducing their mining costs, which were and are yet too high to meet competition from the non-union fields of Somerset and Westmoreland counties. Of several loaders presented for their consideration the model of the Joy loader shown by Mr. Joseph F. Joy, seemed to hold the greatest possibilities, and after extended study, the management decided to invest in a machine of this type. A machine was built, which as far as the writer knows was the only one of its type ever put on the market. This machine arrived at one of the mines early in 1920 and was put to work immediately. It was a forerunner of the present 4-BU and 5-BU types, but differed from them very radically as to design. In general the machine consisted of the familiar Joy gathering arms and a short conveyor which discharged into a steel tank which held about four and one-half tons of coal. This tank was emptied by a second conveyor which placed the coal in the mine car. The object of this conveyor tank was to provide storage room while changing cars and to allow the machine to load on the entry while the room was short. This plan was very efficient and from our experience was worth retaining, but has been abandoned by the Joy Company on account of its making the machine unwieldy. The whole machine was mounted on caterpillar tractors which were driven by two 10-H.P. Westinghouse series wound motors, each having its own controller, the controllers being arranged in tandem so as to be operated by the same handle. This very ingenious scheme which is shown in Figure 4, was supposed to make it possible to steer the loader by the controllers. By swinging the handle one way both motors moved forward, by swinging the handle the other way both motors moved backwards and by twisting the handle as shown by arrows, one motor moved ahead and the other back, thus causing the machine to turn. This scheme proved a failure as the loader was too temperamental and erratic in its operation. After Mr. Joy, himself, narrowly escaped serious injury, this device was taken off and the controllers manipulated separately. This system never proved satisfactory and was abandoned' for

Jan 1, 1925

By J. C. Rae

A Japanese mining engineer was given a year's leave of absence by his company and dispatched on a tour of inspection of all the principal coal mining regions of the world. He visited the New Castle region of England, Wales, Scotland, France, Germany and Alsatian mines, the underseas col¬lieries at Nova Scotia and Vancouver, and our own important fields of Illinois, Pennsylvania, West Virginia, Kentucky, Colorado, Utah and Wyoming. You are probably surprised to know that after seeing all these, he pronounced the Gebo mine of the Owl Creek Coal Company as the most interesting operation he had seen. The Gebo Mine is located about three miles west of Kirby on the Chicago, Burlington & Quincy Railroad in the Big Horn Basin region of Wyoming, 500 miles north of Denver and 200 miles south of Billings, Montana. The mine is working on a coal bed five or six to eleven or twelve feet' thick, dipping 22 to 23 degrees toward the northeast. The coal occurs in what is called the Eagle formation; and is found between two massive sandstones from 25 to 65 feet thick, which, weathering into bold', gray-colored cliffs, serves as a guide to the location of the coal bed. The deepest workings have an overburden of 800 feet. Cleavage planes of the coal extend at an angle of 45 degres to the pitch, and perpendicular to roof and floor. The coal itself is generally clean and not difficult to cut. It ignites readily from spontaneous combustion, however, which circumstance makes an ever-present fire hazard which must be carefully watched and guarded against. The coal is classed as sub-bituminous with analysis about as follows: Moisture 17% Volatile Matter 33% Fixed Carbon 46% Ash 4% Sulphur, about ½ % B. t. u. value a trifle under 11,000. It is known as Owl Creek coal, is one of the best domestic and steam fuels in the West, and is very popular in Montana, Idaho, Washington, Wyoming, South Dakota and Nebraska. While the coal slacks somewhat rapidly when exposed to the weather, it stores readily for months if placed under cover. On account of the somewhat isolated position of the mine as regards manufacturing establishments, there was a decided difficulty in disposing of slack, especially during the early years of the mine (1907 to 1914), and approximately 10 per cent of the entire product had to be wasted as slack during those years. This difficulty has been largely overcome since 1914, due partly to growth of manufacturing establishments in tributary territory, and also to enlarged transportation facilities. Also largely due to its isolated position, the mine has been compelled to use an extremely large proportion of box cars, much over 50 per cent of the product (in some years 75 per cent) being shipped in box cars, which, of course, entails extensive loading equipment and increases cost of loading. The output of the Gebo Mine for 1920 was 348,000 tons, for 1921, 273,000 tons; the rate of production during the year 1922 was over 1,700 tons daily, and 2,000 tons daily in January, 1923. The mine was developed by driving three openings straight down the pitch, the main slope being 12 to 14 feet wide and 3,000 feet long. A little distance from the surface a pair of level entries were turned right and left, known as the first East and first West. From these, rooms were driven up the pitch and chute mining attempted with only indifferent success: The failure of this rise-room method of mining was attributable to several

Jan 1, 1923

Briefly, the machine consists of a steel frame mounted on roller bearing wheels and axles, an electric motor, a fully enclosed speed reduction gear unit, a specially designed centrifugal pump driven through a friction clutch and silent chain, a mixture tank and agitators, and all necessary operating and control mechanism. The wheels are mounted on solid roller bearings made of special roller bearing steel, and are cast with deep chilled threads. The axles are of high carbon axle steel. A General Electric Company motor, of special design to exclude dirt and moisture, is used. It has an unusual overload capacity and a maximum torque at starting speed. Special arrangement can be also made for storage battery operation. The motor drives from one end, through a flexible coupling, to the speed reduction unit, and from the opposite end, through a similar coupling, to the pump clutch. The design of the flexible couplings is such that the drive is reversible. The speed reduction gears are enclosed in an oil and dust proof housing. All spur gears, as well as the main drive clutch, are made of steel forgings, with accurately cut teeth. An aluminum bronze worm wheel and special heat treated alloy steel worm provide the speed reduction for the traction drive. The worm shaft is mounted on Hyatt roller bearings and the thrust is taken in each direction by ball thrust bearings. The main drive shafts are of special alloy steel and operate in Hyatt roller bearings. The slow speed shafts run in extra large bronze bushings. Ample and constant lubrication is provided by splash from the gears running in oil. The Mudite pump is of special de- sign. A renewable wearing plate protects the pump casing from the natural wear of the mixture. The open runner is mounted on an extra large shaft which runs in a Hyatt roller bearing on the pump end and in Timken roller bearings on the outboard end. A special cage prevents water and grit from reaching the pump bearing. All thrust from the runner is taken on the Tim- ken bearings and these bearings also provide for the accurate and easy adjustment of the runner. The pump is driven by a silent chain, which operates on cut steel sprockets, from a friction clutch. The clutch is designed to secure long wearing qualities with minimum attention and its adjustment is easily effected. It is mounted on Hyatt roller bearings and the clutch drive shaft also runs in the same type of bearings. The pump discharges through a nozzle, which is adjustable, and controlled by the operator. The mixture tank is of approximately 650 gallons capacity. It is provided with a mixing well constructed of perforated plate screen to prevent large hard particles from getting into the valve or pump. The tank is filled through an opening in the top directly into the mixing well. On a shaft running longitudinally through the tank are arms so arranged that the mixture is thoroughly mixed and kept in continuous circulation from end to end. This shaft is driven from the speed reduction unit by a steel roller chain operating on cut sprockets. The traction drive is taken from the worm wheel shaft through steel roller chains of extra large size that run on cut steel split sprockets on both axles. An idler sprocket provides for easy chain adjustment. The axles are mounted in solid roller bearings in fully-enclosed dust proof housings, which support the frame through coil springs. These springs eliminate twisting strains on the frame on account of track irregularities and also relieve the working mechanism from road shocks. The speed reduction from the motor to the wheels is such that it gives an operating speed of approximately ninety to one hundred thirty feet per minute. The brakes are of the conventional shoe type and engage the wheels on both axles. They are operated by a hand wheel conveniently located and

Jan 1, 1925

Business meeting was opened at 9:30 a.m., June 28, 1967. President James Westfield asked that the meeting come to order. "We have some business to be taken care of this morning. First, we will have a report from the Auditing Committee." Mr. W. S. Landers read the report and said that it had been audited and approved and the motion was made and seconded that it be accepted. It was accepted unanimously. (See Index for Treasurer's Report.) The Resolutions Committee Report was read by Mr. Cliff Artis as follows:

Jan 1, 1967

By John D. Janak

Thank you for inviting me to come here and be your keynote speaker. Texas also thanks you for being included as part of the Rocky Mountain Coal Mining Institute. We'll kind of think of Texas as Baja Rocky Mountains. I've always wondered why coal miners were the only people to go to the mountains in the summer time-and now I know why. The program committee should be given a big hand for selecting this RESORT. And the golf course is stimulating to say the least. This is a very beautiful location. I was asked to talk about CHALLENGES, OPPORTUNITIES and INNOVATIONS as they affect the coal industry. I am going to do that from a Texas perspective. But first, since Texas is the newest state to belong to the Institute, I would like to give you a little background on how our coal industry got started and where we are at today. The vast majority of our coal is called lignite-it has a little lower heating value than most other coals and ranks somewhere between buffalo chips and sub- bituminous. Lignite is found In three geological formations running Northeast to Southwest through South and East Texas. In-place reserves lying within 200 ft. of the surface total 14 billion tons. This slide shows the lignite formations with cur- rent mine operations colored in RED. Mines that are planned to be built in the next 10 years are shown in BLUE. Lignite was used mostly by settlers in Texas during the 1800s. It was used as a fuel to fire locomotives during the Civil War. Between 1900-1930, about 100 mines, mostly underground, were operating in Texas producing lignite for home heating and as a boiler fuel. Here are some slides showing underground access, [lie tipple used to process the lignite, and the underground workings. This is the "BIG LUMP COAL COMPANY" as shown here. The typical underground mine was 100-150 ft. deep and each miner produced 7-10 tons per day-all by hand. In 1926, the Texas Power & Light Company built the Trinidad Power Plant and began using lignite as a boiler fuel. The lignite was mined by the McAlester Fuel Company at the nearby Malakoff Mine. Here are some slides showing a stripping shovel at Malakoff uncovering lignite. The lignite was loaded into railcars in the pit for transport to the power plant. This is a picture of the Trinidad Plant which had two 20 MW units and one 32 MW unit. At the time, Trinidad was the largest power plant in the United States using lignite exclusively as a fuel. Trinidad operated until 1942 when it was converted to natural gas that was sold to the plant for 3 ½ ¢ per MMBT'U. The mine closed after having produced 7 million tons. Lignite was mostly forgotten about until 1953 when Alcoa started an aluminum smelter. Our Company formed a subsidiary called Industrial Generating Company to operate the power plant that furnished electricity to the smelter. We also operated the nearby Sandow Mine that supplied lignite as a fuel to the power plant

Jan 1, 1989

By F. A. Young

A description of the dry process coal cleaning plant which has been built and operated by St. Louis, Rocky Mountain & Pacific Company at their mine at Brilliant, New Mexico, should at first be a description of the special machinery which is used in this process. This equipment consists primarily of screens for sizing the coal into six different sizes all smaller than 1 ½ inch and the pneumatic machines for cleaning each size. These machines are patented and were manufactured by Sutton, Steele & Steele of Dallas, Texas, until a few months ago when all rights of sale were acquired by the American Coal Cleaning Corporation. These screens, a plan of which is now before you, are called anti-gravity screens because the coal travels up hill. The screens which we have at Brilliant are 3 feet wide and 7 feet 4 inches long. They consist of one upper deck which slopes upward in the direction of the flow of the coal, at an angle of 12 degrees. This deck is a wire mesh screen the size of which determines the size of oversize from that screen. Under this is a lower deck with a slope of 7 degrees. This is a solid bottom and is for advancing the undersize to the next screen. On account of the difference in pitch of these decks they are about 11 inches apart at the discharge end, which allows the oversize to be taken off at one or both sides and the undersize to fall only a few inches on to the following screen. This is perhaps the most valuable point in this patent as it allows any number of screens to be placed on a-level floor, tandem in a battery without elevating or rehandling the coal in any way. The length of the screens corresponds to the proper spacing of the cleaning tables which naturally operate on the floor below. I know of no other screen which can be operated in this way. The coal is caused to travel by a reciprocating motion. A shaft as shown near the center of the screen box and under it has an eccentric at each side of the screen with connecting rods attached near the rear of the screen box. The screen box is attached to the stationary under frame by means of cast iron plates extending full width across the screen box. These are placed at an angle as shown so that the forward motion of the eccentrics causes the screen box to rise as it moves forward and the backward motion drops the screen from under the coal thereby causing it to advance. The coal advancing over the screen cloth in this rolling or jumping motion causes very perfect sizing. It should be stated here that very accurate sizing is necessary for the success of the cleaning tables. The stroke is 1 inch and the speed 350 revolutions per minute. In describing the pneumatic cleaning table, I place before you a plan furnished by the makers. The basic principle is that if a film of coal one to two inches thick and all of nearly the same size pieces is placed on a flat perforated surface and a large volume of air passed through it, the lighter particles which are the clean coal will soon find their way to the top of the film, while the heavier particles, or waste, will remain on the bottom. The machine is built with a perforated deck about 4 feet square under which is an air chamber and air duct connecting with a fan which is part of the machine. The deck of the table has a reciprocating motion the same as the screens already described, which tends to advance the product up a slight slope which is adjustable. The coal is fed at one corner of the table as shown and the deck slopes also away from the feed and at right angles to the reciprocating motion. On top of the perforated deck are riffles about 2 inches apart and running parallel to the line of reciprocating motion. These riffles are about 1/2 inch high at the fan and feed side of the table and taper to nothing at the far side. When the coal is fed on to the table, the air through the perforations tends to raise it 'and roll it over these riffles down the slope toward the clean coal discharge. The heavier particles do not get over the riffles so rapidly and the reciprocating motion is constantly pushing them

Jan 1, 1923

Earl W. Baker W. P. Bigler Lyman Fearn Leslie H. Johnson V. O. Murray Max C. Scheble Fred L. Smith who left the world better for their having lived in it . . .

Jan 1, 1986

will be held at COSMOPOLITAN HOTEL DENVER COLORADO June 3,4,5, 1931

Jan 1, 1930

Jan 1, 1963

By Dan Jackson

9:00 a.m., June 28, 1983 MR. MORTENSEN: Good morning ladies and gentlemen. Again, it gives me great pleasure to welcome you to another session of the 79th meeting of the Rocky Mountain Coal Mining Institute. The thing again that has always been impressive are the activities that we've had so far. The success in the meetings has been delightfully encouraging to all of our committee people. Please welcome the chairman of the session, Charlie Margolf. MR. MARGOLF: Thank you, Vernal. Good morning, ladies and gentlemen. It would be my privilege to serve as the session chairman this morning. To allow the maximum time for our speakers, I'll turn the microphone over to Bernie Bernstrom who will introduce our first speaker. MR. BERNSTROM: Thank you. As Vernal mentioned, Dan Jackson will be our first speaker. He is the Western Editor of Coal Age Magazine. Dan really doesn't need an introduction to this group. He's belonged to the Rocky Mountain Coal Mining Institute about 25 years. Dan is a native of West Virginia and he's an ex-coal miner. He graduated form West Virginia University as an electrical engineer and worked for Amherst and West Bending Coal prior to employment by Coal Age Magazine. Back in 1972 Coal Age moved him to Denver from New York City. MR. JACKSON: When Vernal Mortensen asked me speak to the members of the Rocky Mountain Coal Mining Institute earlier this year I found it impossible to say no to the guy because of what he has contributed to western coal. Little did 1 know that the subject he had in mind would be entitled, "An Outsider's View of Western Coal." At first I asked myself-I've been associated with the coal industry for some 38 years, 12 years in national operations and 26 years reporting on it. You might say that I've been married to two industries, coal and the business press for 26 years, but today I'll put on my business press hat and try to make an impression of what an outsider might think of western coal. But at the outset, let's get one thing straight: When you say press, whether it's business press, the media or whatever, and you heard some comments yesterday as far as what the media has done .to this industry and there's been some definitions bandied around as to just what an editor is. One of the most recent ones has defined an editor as a person who can talk on any subject with an open mouth. Now that's not my case. Secondly, I don't give long talks. Several years ago I was giving a rather lengthy talk to a group similar to this and it was halfway through the talk when I noticed one guy on my right looking at his watch quite frequently. I didn't mind that too much because all of us do that once in a while, but when he looked at his watch, took it off and shook it, I thought, "My God, better cut short." But for more than a decade western coal has enjoyed substantial annual increases in production from some 30,000,000 tons in 1970 to some 264,000,000 tons in 1981, but 1982 was a different story. We lost about 6,000,000 tons of production in that year. In 1983 it's expected to be a little worse than '82. Coal historically doesn't rebound from a recession as quickly as other industries. It takes about eight to 10 months longer for us to really get moving again and I'm afraid that you'll still have to don your fighting helmets and flack jackets when you go out into the market to sell your product. Western coal, as you know, has problems and al l of them are not going away when the recession ends and they won't go away overnight. I'm sure most of you are aware of what those problems are. Carl Bagge and Jim Harris, along with other speakers, at this meeting have educated us well on those problems and I'm sure you'll hear more from Jim Watt at today's luncheon. If everyone in this room were asked to list three orfourof the most serious problems facing western coal, I'd make book that the total of the answers wouldn't vary by more than 3 to 5%, if that much. But coal is not the only mining segment in the U.S. with problems. Metal and non-metal mining has its share, too. I'd like to step back into the past for a few minutes, if I may, to a time when our problems were just beginning. Since 1979 a third of the nation's mines, including coal, metal and nonmetal have been shut down. The total volume of all mining in the U.S. in that year totaled some $24 billion. Today that figure has dropped some 21 %. The after tax rate on return for mining companies has fallen from 6'/% in 1980 to minus 3% in 1983. But that's really not where our problems began. They began 20 years ago when a profound change began taking place in the U.S. economy. Our economy had been growing at about 2'/-3% annually without exception except for the great depression. Our inflation rate was about I'/%, interest rates were running about 6%, and the federal budget was $77 billion, really great figures compared to today. From 1960 to 1980 the federal budget increased almost 1.000% and taxed paid by individual families increased by 700% during that same period. Despite the huge increases in taxes, the federal deficit kept getting larger and larger year after year and within this 20 year period the national debt climbed to a trillion dollars. Economic progress of this type can't continue indefinitely without some serious consequences. The result of that economy, well, you know what happened and there is a direct relationship of that

Jan 1, 1983

The Annual Business Meeting of the members of The Rocky Mountain Coal Mining Institute held during the 83rd Regular Meeting of the Institute was called to order by the president, Bernard Bernstrom at 2:50 p.m. Tuesday, June 30, 1987 in the Janss Auditorium of the Snowmass Conference Center in Snowmass Village, Colorado. Thirty-one were present and a quorum was established. The president outlined the purpose of the meeting was to inform the members of the status of the affairs and activities of the corporation during the preceding year. It was moved by Leon Jeannot, seconded and carried to approve the minutes as published in the 1986 Proceedings. The chair called for reports of the various committees and these reports will by placed on file in the RMCMI Office. Bylaws and Resolutions. Chairman Loren V. Linville reported there were no bylaws revisions. He further reported that the Board had adopted three resolutions: (1) Noting the passing of members since the last convention-Benton Boyd, E. A. Hare, E. S. Moran, Jr. and Edward Prostel. (2) Of appreciation to the Executive Secretary, officers, chairman, Diamond Jubilee chairman and committees and convention committees for an outstanding job in preparing for the 83rd Regular Meeting of the Institute. (3) To recommend to all RMCMI members that, on an individual basis, they each oppose replacing coal fired generation with natural gas generation. Membership. Chairman Leon Jeannot reported that at the beginning of the 1986 fiscal year, there were 881 active or dues-paying members. During the year, 219 members were dropped for a variety of reasons such as non-payment of dues, transfer, employed elsewhere, change of address. Ninety-six new members have been recruited for an active total of 758. In addition there are 55 Life Members, 20 senior members, six scholarship winners and seven supporters for a net total of 846. The budget of RMCMI calls for 1,000 active members and we must address and plan for those short-term prospects as they will certainly impact our membership. A full report is on file in the RMCMI office. Patrons of the Institute. Chairman Ira McKeever reported that only 59 Patrons renewed their support during 1986-87. Program. Chairman Bill Balaz announced that the convention program theme "This is OUR Life", as presented in "Past", "Present" and "Future" segments was very well received. He called for additional helpers another year and suggested that next year's program format be changed to a hard hitting one. Publicity. Chairman Tom Egan reported that of the three newsletters sent members during the year, that the most effective one was the newspaper format one and recommended its use next year. RMCMI hired Bob Jacob who heads his own public relations firm to solicit advertising for the Proceedings on a contract/ commission basis. He attended the convention for this purpose and to solicit business card ads. A full report is on file in the RMCMI office. Scholarship. Chairman Keith McGinnis reported that five of the six scholarship recipients were present at the convention. Each was introduced to the membership at the Tuesday morning Scholarship Breakfast, presented a plaque and responded. The input from each winner was most favorable to the program. Each was appreciative of the many contacts made and the educational seminars and programs. The selection process started in March and was completed in May, except for one university which had difficulty in providing a candidate. It is suggested that the initial contact with the institutions be made in December and completed by April 1. This year, for the first time, three of the six universities were visited for the purpose of interviewing the candidates. They were Colorado, Utah and Wyoming. A very positive feedback was received from these schools and it is recommended that the practice continue. CONVENTION COMMITTEES Convention Arrangements. Doris Finnie presented the following report: As a professional meeting planner, this Diamond Jubilee convention was indeed a great challenge. One meal was added to the package and thus increased the individual cost. Snowmass Resort Association is unique in that they utilize a conference coordinator who acts as the middle man between myself and the usual persons we deal with, like AV personnel, the chef, the banquet director, the steak fry personnel, the Sunday tour etc. so the office had to become creative. For instance, we learned early on we could not deal with the local florists. It cost us lots less to buy our flowers wholesale in Denver, have my husband drive them up and our West Virginia daughter to arrange them! But, finally her floral arrangement class at CSU paid off! This was truly a Finnie family orchestrated convention. Our Lakewood daughter acted as Scholar-

Jan 1, 1987

D. HARRINGTON: Owing to lack of funds, the United States Bureau of Mines have made no experiments in the Bruceton mines in the use of mudite. MR. McAULIFFE: I doubt that mudite cam be delivered at fifty cents a ton and that a mile of heading can be treated with mudite for ten dollars. You could not dig a ton of sand out of a sand hank for that money. L. C. CLARE: The tram road leading to Wattis mine crosses a shale bed and it is easy to screen the shale through a %-inch sieve and load it into a mine car. W. J. REID: A slow trip passing through a mudited entry will dislodge practically no dust, a rapid trip will make air disturbance enough to coat the cars with fine dust. MR. PRYDE: We have used mudite on stoppings around a fire in Reliance and for two months thought they were getting good results, but the fire was found to be drawing air and to be spreading. This mudite was smeared over the stoppings with a trowel. After this apparently failed we used dry adobe.

Jan 1, 1925

By John M. Jennings

The Hiawatha pitmouth is located at the head of the middle fork of Miller creek, at an altitude of approximately 8,100 feet. The coal is lowered to the tipple down a gravity tram two miles long, in 16 car trips which carry about 60 tons net. The average running time of the trip is about nine minutes. At the bottom of the tram there are two tracks for the loads and two for the empties. The trip, after being cut off the rope, is dropped by gravity onto a feeder, where the cars are uncoupled and fed one at a. time across the pitcar scales and into the dump. The dump is of the full revolution type, friction driven. On passing out of the dump the cars are returned by a kickback onto the empty car haul. They are caught at the bottom by a brake which consists of a pair of steel squeeze blocks operated by heavy springs. The empties are elevated to the double tracks, where the trips are made up. The feeder, scales, dump and empty car haul are all built on the solid ground of the hillside instead of being incorporated in one structure with the screening plant. The coal is dumped into a small hopper with a capacity of about 15 tons, whence it is fed by a reciprocating feeder onto a scraper conveyor which takes the coal over to the screening plant, a distance of 120 feet. This conveyor is 48 inches wide and travels at 120 feet per minute. The screen itself is interesting. It is of the Marcus Horizontal type.

Jan 1, 1925

At the Annual Meeting of the RMCMI Board of Directors held June 29, 1985, the following amendments to the corporation bylaws Article III were made: Section 2. Advisory Board. There shall be an Advisory Board of Directors which shall be com- posed of all former presidents of the corporation and of the unincorporated association, also known as The Rocky Mountain Coal Mining Institute, of which the corporation is the successor. The Advisory Board shall periodically review the philosophy and policies of the corporation and make recommendations concerning the same to the Board of Directors. The Advisory Board shall hold an annual meeting at the same place as and immediately pre- ceding the annual meeting of the members in each year and written notice stating the place, day, and hour of the meeting shall be given or mailed to each member of the Advisory Board at least thirty days prior to the date fixed for such annual meeting. The annual meeting of the Advisory Board shall be for the purpose of electing a chairman from among its members and the person so elected chairman shall also serve as a member of the Board of Directors of the corporation. The Advisory Board shall meet at such other times and conduct its affairs in such a manner as it shall determine from time to time by resolution. Section 4. Regular Meetings. A regular meeting of the Board of Directors shall be held immediately following the annual meeting of the members, at the site of the annual meeting of the members, the day and time to be fixed by the Board of Directors at its annual meeting immediately pre- ceding the annual meeting of the members in each year, without the necessity of any other or advance notice. Such regular meeting of the Board of Directors shall be for the purpose of considering committee appointments, and for the transaction of such other business as may come before the meeting. A regular meeting of the Board of Directors shall also be held in the Fall of each year following the annual meeting of the members and written notice stating the place day and hour of the meeting shall be given or mailed each member of the Board of Directors at least thirty days prior to the date fixed for such regular meeting. Such Fall regular meeting of the Board of Directors shall be for the purpose of receiving the treasurer's annual financial report of the previous fiscal year as reviewed and approved by the auditor, to take action on the budget, and for the transaction of such other business as may come before the meeting. Section 8. Standing Committees. The Board of Directors may create by resolution adopted by a majority of the entire Board of Directors, a Bylaws and Resolutions Committee, a Nominating Committee, a Finance Committee, and one or more other committees each of which shall consist of two or more directors and which shall have and may exercise such authority in the management of the corporation as shall be provided in such resolution or in these bylaws. Section 9. Ad Hoc committees. The Board of Directors from time to time may by resolution create a Membership Committee, a Scholarship Committee, an Education Committee, various convention committees, and one or more other committees each of which shall consist of members of the corporation and which shall have and may exercise such authority, other than in connection with the management of the corporation, as the Board of Directors may determine. MINUTES of the Rocky Mountain Coal Mining Institute 81 st Member Annual Business Meeting July 2, 1985 The 81st Annual Business Meeting of the mem¬bers of The Rocky Mountain Coal Mining Institute was called to order by the president, Charles W. Margolf at 1:35 p.m. Tuesday, July 2, 1985 in the Windom Peak Room of the Tamarron Resort near Durango, Colorado. Thirty members were present and a quorum was established. It was moved by Bill Balaz, seconded and car¬ried to dispense with the reading of the minutes as these were published on pages 67 thru 77 of the 1984 issue of the Proceedings. The chair called for reports of the various com¬mittees and these reports will be placed on file in the RMCMI Office. Bylaws and Resolutions. Chairman Loren V. Linville reported that the Board of Directors had adopted changes to Article III, Sections 2, 4, 8 and 9 calling for clarification of Ad Hoc and Standing Committees as well as setting forth a purpose for the Advisory Board meetings and stating a time for an annual meeting. He further reported that the Board had passed three resolutions: (One) Noting the passing of these members since the last conven¬tion - Einar M. Arentzen, Gerhardt A. Benne¬witz, Claude P. Heiner, Raymond A. Johnson, Vard H. Johnson, P. T. Schonstrom, Augusta F. Whiteside and Edward Wiemann; (Two) Of appreciation to the officers, chairmen and their commit-

Jan 1, 1985

The sixth Annual RMCMI Mine Rescue Evaluation was held during the 1997 Institute convention at Sheraton Steamboat Resort, Colorado. The Mine Rescue committee, co-chaired by Becki Boam and Gary Cook, is one of 18 committees of the Institute. In 1997 the largest number of teams participated in the program. There were nine: BHP Minerals - La Plata Mine, BHP Minerals - Navajo Coal Co., BHP Minerals - San Juan Coal Co., Bridger Coal Co., The Coteau Properties Co., General Chemical Co., The Sabine Mining Co., Solvay Minerals and Western Energy Co. Professional evaluators who provided challenging scenarios for the 80 participants were Jack Knight of Milton, Florida; Wilson Begay, Chris Saxon, and Gaylon Yazzie all of Western States Security; Mary Bailey, Bailey Associates; Tom Bass, California Department of Corrections; and Art Saenz, BDC. Seven members made up each team plus one or more trainers and represented the states of Montana, New Mexico, North Dakota, Texas and Wyoming. Ten different scenarios were presented during the two day evaluation. Each team was given the pertinent information to solve the problem as they assembled at the site. Mine Rescue families and friends participated as victims providing realistic scenarios to simulate the stress of an actual rescue incident. Each team was unaware of the circumstances until arriving at the various scenes in and around the Sheraton resort. [ ] These teams are providers of prompt rescue and medical care for accident victims at their respective properties. The members act with immediate and professional knowledge to save lives and prevent further injuries. Sponsors who contributed financially to the 1997 program are: Argo Industrial, Antelope Construction, Fisher Safety Supply, Flanders Electric Motor Service, Inc; Intermountain Electronics, Inc.; King Energy Services, Inc.; Rocky Mountain Electric Motors, LS.; TerraMatrix and Triune Inc. On Saturday evening, June 28, a reception was held for all mine rescue participants and spouses who had advance registered for this social event. The RMCMI Board of Directors was invited to attend and meet with the teams. As convention attendees, all mine rescue participants and registered families attended the Monday night country western reception and Bar-B-Q. This was followed by an adult western melodrama. [ ] Glass awards with the RMCMI logo and a Mine Rescue figure were presented at the Tuesday Mine Rescue buffet breakfast to all nine teams, each of which had achieved proficiency at level 3. Captains of the teams pictured below are (from left standing): Ron Neff, BHP-San Juan; Ted Laughline, Bridger, Terry Davis, Coteau; Jim Knutson, General Chemical (from left kneeling): Dan Allerdings, Rosebud; Ron Miller, BHP-Navajo; Jonathan Sorrell, BHP-La Plata and Ray Blaisdell, Solvay. Gary Cook is to be commended for his solo last minute supervision of the Mine Rescue program, due to Becki Beam's unavoidable absence. The teams look forward to the 1998 convention at Snowmass Village Resort, Colorado Thursday and Friday, June 25 and 26.

Jan 1, 1997

Jan 1, 1921