Search Documents

By Northcutt Ely

This volume- summarizes mining and petroleum legislation in 18 European jurisdictions. Within these jurisdictions, primary attention is given to requirements that must be met in each country for acquisition of rights to permit development of mineral resources. Coverage includes: First, identitication of the controlling laws or statutes governing minerals acquisition and reference to the administrative authority; second, analysis; of the laws governing mines and quarries and their products; third, analysis of laws applicable to natural gas, petroleum, and related materials; and fourth, mention of laws regulating offshore operations. Where pertinent, sections dealing with historical background or administration have been added in countries where minerals are subject to control of States or Provinces, those areas are considered separately from the central government.

Jan 1, 1974

By R. V. Ramani

One area of study in the Coal Mine Injury Analysis project was to illustrate and enhance the ability of mine safety management personnel to apply analytical techniques to injury experience data and to justify requests for funds for safety enhancement actions on a cost/benefit and other quantitative basis. Four volumes of this final project report detail (1) the objective and scope of the mine safety management research, (2) the results of literature review, and case studies, and (3) models developed for mine safety management. The four volumes are titled as Volume III: Mine Safety Management, Volume IV: Analytical Techniques for Mine Safety Management; Volume V: Mine Safety Management Case Studies and Volume IX: Training Cost Model. In this volume, the following material is presented: (i) review of related literature, (ii) mathematical models to perform quantitative analyses of accident/ injury experience data using the tools and techniques of risk analysis, time series analysis, and the Markov process, and (iii) descriptions of the HDBSEL and ACIM programs which are used to perform accident/injury experience analyses and cost analyses, respectively.

Jan 1, 1993

By Gloyd M. Wiles

The property of the Park City Consolidated Mines Co. is situated in the northeast part of the Park City dining district 1 mile east of the town of Park City. The elevation at the collar of No. 1 shaft is 7,250 feet. Park City is a town of approximately 4,500 population lying about 30 miles east of Salt Lake City. The two are connected by an oiled State Highway, which is cleared of snow in winter and maintained in first-class con¬dition by the State throughout the year. The district is served by branches of the Denver & Rio Grande Western and Union Pacific Railroads, each operating on a daily' schedule, except Sunday. These two railroads have constructed 1 ½ miles of joint track from the town to the Park City Consolidated Mines Co. loading tipple, located 200 feet from the portal of the adit that leads to No. 1 shaft.

Jan 1, 1936

By E. G. King

The literature contains little thermodynamic information regarding inter-oxidic compounds of the ferroalloy elements and, as a result, thermodynamic considerations of extractive and utilization processes involving these elements have been hampered. As part of a Bureau of Mines program to improve this situation, this paper reports the heats of formation of three calcium vanadates and two magnesium vanadates. There were no previous similar data for any of these compounds. The experimental method was hydrochloric acid solution calorimetry, using calorimetric reaction schemes involving the vanadates and their component oxides. The results were expressed as heats of formation from the component oxides and from the elements. Corresponding free energy of formation values were calculated. The data show that the calcium and magnesium vanadates are stable with respect to all possible decompositions in which vanadium remains pentavalent. This conclusion is similar to the one drawn by Koehler6 for three sodium vanadates.

Jan 1, 1962

By Robert C. Dyni

The Bureau of Mines in cooperation with the Solution Mining Research Institute conducted surface and subsurface investigations over five solution-mined salt cavities in the Hutchinson, KS, area. The purpose of these investigations was to determine the mechanisms that lead to the formation of sinkholes above collapsed solution cavities. Of the five salt-solution cavities investigated, four had collapsed and produced sinkholes prior to the time of the investigations; the fifth cavity was considered stable. Exploratory drilling and coring operations were conducted at all five sites; surface stability monitoring was conducted at three of them. The results of these studies indicate that excessive dissolution at the salt-shale contact of each collapsed cavity produced large, unsupported roof spans that ultimately exceeded the structural integrity of the overburden. The stable cavity was not exposed to excessive dissolution at the salt-shale contact; this limited the roof span and ensured a stable cavity. The data also show that surface settlement in the vicinity of the two surface-monitored sinkholes continued for approximately 7 years after the sinkholes formed, indicating that the rubble piles of the collapsed cavities were undergoing gradual consolidation.

Jan 1, 1986

By R. G. Knickerbocker, T. E. Evans, D. R. Torgeson

"INTRODUCTION Sponge iron is a product resulting from the reduction of an iron oxide at such a low temperature that fusion does not occur, and the reduced particles retain substantially the same shape as the original ore. The removal of oxygen in the reduction process leaves the metal porous and reactive. Sponge iron may be compared in general to a chemically precipitated substance insofar as reactive properties are concerned. The high specific surface and the orientation of metallic structure are factors which probably contribute to the reactive properties of sponge iron.The term ""gaseous reduction,"" as applied to iron ores, required clarification. Strong evidence exists, for example, that ore is partly reduced to sponge iron by carbon monoxide in the blast furnace at temperatures around 800° C. at a point that may be as high as 30 feet above the tuyores. In 1923 and 1924, Sims and Wood attempted to reduce iron oxide with carbon in an Arsem vacuum furnace at 980° C. These investigators found that only 6 percent of the iron was reduced to metal when the iron oxide-carbon mixture was heated for 1 hour under evacuated conditions, whereas at atmospheric pressure 70 percent of the iron was metallized. Their results indicate that the process of iron-ore reduction at temperatures below the melting point of the ore may proceed largely, if not entirely, by the action of reducing gases even when the reducing agent is solid carbon. Therefore, the term ""gaseous reduction,"" as used heroin, is defined as a process in which iron ore is brought into intimate contact with a reducing gas produced in separate-equipment from the reduction chamber itself.A large amount of pilot-plant development on gaseous reduction of iron ores has been carried out by the Bureau of Mines at the Boulder Experiment Station and had as its objective the reduction of fine iron ore by means of producer gas. The use of use gas was prompted by two considerations: First, the possible utilization of large reserves of Western noncoking bituminous coals and lignites contiguous to iron-ore drewwing; and second, an investigation of the results that might be achieved in the pilot-plant gaseous reduction of fine iron ores by means of a relatively reducing gas. The results obtained, it was felt, would be of considerable value in indicating the direction which gaseous reduction experimentation must take for the development of a commercially practicable and economic process for the production of sponge iron."

Dec 1, 1946

By Douglas W. Fuerstenau

A detailed experimental study of breakage kinetics in a batch rod mill indicates that while the system is inherently nonlinear, the feed disappearance kinetics for the finer sizes and the coarser sizes at high holdups is well represented by first-order behavior. The set of breakage distribution functions was found to be normalizable and independent of particle holdup in the mill. The size discretized initial breakage rate functions were found to be inversely proportional to particle holdup and almost directly proportional to particle size. A linearized grinding model that results from the first-order Taylor's series expansion of the breakage rate expression was found to give good simulations of the mill product size distributions without recourse to any parameter improvement routines. Material transport through rod mills was evaluated by investigating the effect of operating variables on the holdup and residence time distribution of particulate solids flowing through the mill. Identical experiments performed in a continuous ball mill helped delineate the fundamental differences in particulate transport through these two types of mills. Mechanistic interpretations of the observed transport phenomena are presented, and their implications in the context of tumbling mill analysis and design pointed out.

Jan 1, 1980

By H. E. Powell

A laboratory investigation was conducted by the Bureau of Mines to study the magnetic characteristics and to measure the magnetic susceptibility of the mineral siderite. All susceptibility measurements were made by the method of Gouy on powdered samples and at room temperature. Specific susceptibilities of samples from 15 different locations, domestic and foreign, were determined. Values ranged from 66 to 103 (10-6) cgs electromagnetic units. The relation of susceptibility to mineral composition is discussed in this report. The specific susceptibilities of 76 minerals are tabulated in an appendix.

Jan 1, 1963

By A. C. Fieldner

All technical facilities of the Bureau of Mines have been geared for more efficient use and conservation of mining equipment, developing plans for safety, improving the quality of coal through better methods of preparation, studying the problems of coal storage and utilization, and extending the uses of coal5/ for the war and postwar economy. The Bureau is now analyzing all of the coal purchased by the Army and much of that required by the Navy. Work on boiler feed water was doubled over last year to meet the increased demand made by the War Department for protecting vital boiler plants in many new camps and defense plants. Progress has been made in safely storing coal to reduce dangers of spontaneous ignition to a minimum and to preserve coking power. Mixtures of oil and coal to be used as a substitute fuel have been investigated. Technical service on the conversion of plants to other fuels has been given to government agencies and private consumers. The possibilities of making motor fuel,

Jan 1, 1944

By Jacqueline V. Rich

The relationship between surface and ground water quality and copper mining in the Globe-Miami area is investigated in this three-year study. Methods to prevent, minimize, mitigate, or treat polluted waters are identified and evaluated. Best Management Practices are incorporated in a recommended plan to manage the area's water quality.

Jan 1, 1983

By M. P. Ristenbatt

A new automated post-disaster signaling system, intended to use through-the-earth EM propagation, was demonstrated in the laboratory at an input SNR of -34 dB. The system presently available requires an input SNR of +6 dB, and uses a human-ear detector. The work here demonstrated coherent integration, for the automated system, in multiples of 17 s, up to 1088 s (18 minutes). A repeating pseudorandom (or pseudonoise) signal is used, which offers an ideal auto-correlation at the receiver matched-filter output. A novel decision-variable algorithm achieves the estimate of noise level by using those matched-filter output samples that occur between the signal auto-correlation peaks. This work included corraboration that the received signal power decreases as distance to the tenth power, for through-the-earth propagation. Thus, the above 40 dB reduction in required input SNR permits an automated system to have a range 2.5 times that of the present system. In addition, an automated system permits the possibility of operating receivers around-the-clock; this would reduce the initial-detection-time from a few hours (present system deployment time) to a few minutes (signal processing time).

Jan 1, 1981

By J. S. Hansen

To improve mine safety, the Bureau of Mines has conducted a search for better materials and systems to anchor roof bolts. This report describes a study on the ability of a gypsum-based anchoring medium to withstand short- and long-term loads. Results showed that 2-ft-long bolts anchored with gypsum that was injected as plaster slurry at a 0.370 water-cement ratio and cured for 10 min sustained pull test loads equal to the ultimate strength of the bolt steel (about 37,000 lb). For comparison, the minimum required capacity is 17,600 lb. Long-term loads of 15,500 lb were sustained with estimated 10-yr movement of less than 1/2 in. Two-foot-long bolts anchored with gypsum installed in a cartridge in which the water was contained in tiny capsules sustained a pull test load of about 30,300 lb at a 0.319 water-cement ratio and 10-min cure time. At a 0.288 water-cement ratio, load capacity was about 37,000 lb. The lower load capacities of cartridge-installed bolts resulted primarily from the remnants of the water-wax capsules. Above 10,000 lb, creep movement of cartridge-grouted bolts appears excessive, but longer bolts may be capable of resisting creep better.

Jan 1, 1985

By E. S. Longfellow, S. H. Katz

Poisonous hydrocyanic acid gas (HCN) is sometimes evolved in dangerous quantities from cyanides used in metallurgical and chemical operations. This gas is much used for fumigating buildings, ships, greenhouses, and such commodities as grain and cotton to destroy rats, mice and insect pests. Wherever cyanide fumes are evolved, thorough ventilation is necessary in order to render the sur- rounding air safe to breathe. Many persons have been killed by entering tanks and fumigated places too soon, and a simple test for this gas would promote safety. In view of the need for an easy method for quantitatively determining HCN in air, the three color reactions used originally for testing HCN in solution tions *** were modified and adapted. The reactions employ (1) picric acid (CH(NO2)3OH) which is yellow but combines with hydrogen cyanide to form a red- purple dye, isopurpuric acid****; (2) phenolphthalin (CH1604), which is a reduc- tian product of the phenolphthalein (CH4) used for acid indicator, this colorless substance is oxidized***** by presence of HCN to pink colored phenolph- thalin; and (3) guaiacum which oxidized from colorless to blue******. Phenolph- thalin and guaiacum require the presence of copper compounds which catalize the color formation by reduction of cupric cyanide. The chemical processes involved *Associate physical organic chemist, Bureau of Mines, Department of the Interior. **Assistant gas chemist, Bureau of Mines, Department of the Interior. 2014 20 *** Kohn-Abrest, E., Notice toxicologique sur les gas: Arnales des Falsifica- tions, vol. 8, 1915, pp. 215-35. (Tested air with picric acid and guaiacum papers). **** Élasiwietz, H., Ueber eine neue Zersetzungsweise der Trinitrophenylsaure: Anal. der Chemie, vol. 110, 1859, pp. 289-303. ***** Weehuizen, F., Phenolphthalin as reagent for HCN: Pharmaceutrisch weekblad, Utrecht, vol. 42, 1905, pp. 271-2. Abstract, Jour. Chem. Soc., vol. 88, part 2, 1905, p. 489. ****** Schonbein, C. F., Ueber den thatigen Zustand der Helfte des in dem Kupfer- oxydenthaltenen Sauerstoffs und ein darauf beruhendes hochst empfindliches Reagens auf die Blausaure und die loslichen Cyanmetalle: Jour. fur. Praktische Chemie, vol. 106, 1869, pp. 263-70.

Jun 1, 1923

By J. G. Kirby

The total number of petroleum refineries in the United States continued to decline during 1950, and according to the Bureau of Mines annual refinery capacity survey there were 357 refineries January 1, 1951, compared with 367 a year ago. The total throughput capacity increased 267,344 barrels daily during the year to 6,963,644 barrels daily as of January 1, 1951, continuing the trend of the past several years to increase the throughput capacity of the refineries and decrease the number of plants. The capacity of the average refinery to process crude oil increased during 1950 from 18,246 barrels daily to 19,506. The Indiana-Illinois refinery district accounted for 110,175 barrels, or 41 percent of the total crude-oil capacity increase, the Oklahoma-Kansas district, 17 percent, the California district, 14 percent, the East Coast district, 13 percent, and the Louisiana Gulf Coast district, 12 percent. Slight declines ill crude-oil capacity were reported in the Texas Inland, Texas Gulf Coast, New Mexico, And Appalachian refinery districts. The 160,100 barrels of additional crude-oil capacity that was building January 1, 1951, represents an increase of 10 percent over the year earlier figure. The only completely new refinery listed as under construct ion at the beginning of 1951 is located at Superior, Wisconsin. Other new construction involves enlargement of existing refineries. Plans for at least five additional new refineries are under consideration, and construction is expected to begin during the current year.

Jan 1, 1951

By R. Q. Shotts

Factors of geological structure and occurrence of coalbeds, plus the resulting mining conditions, have required more care in preparing coals in Alabama than in most other districts almost since mining Alabama coals began. For this reason, literature on these coals may be interesting to those in areas where prime coals have been mined out, and thinner and less regular beds must now be exploited. This literature review has been arranged in order of subject matter. Some references have been listed more than once, but each separate review is limited to the material pertaining to the subject matter being discussed. For those seeking specific information, the authors have indicated which items repeat material and which items are most complete or specific. Geology, preparation, and carbonization of coal have been reviewed the most frequently.

Jan 1, 1963

By Philip Thompson

The Bureau of Mines investigated a selective flocculation-flotation technique to remove insoluble slimes from low-grade potash ore in a continous 45-kilogram-per-hour (100-pound-per-hour) process investigation unit (PIU). This research is part of the Bureau's program to improve resource recovery from low-grade ores. Results showed that 84 percent of the insoluble slimes were removed from an ore containing 5.5 percent water-insolubles and 14 percent K20 using a Bureau-developed, cationic flocculant-glycol ester-diesel oil reagent. Subsequent potash flotation recovered 75 percent of the potash in a cleaner concentrate assaying 56 percent K20. Concentrate leaching upgraded the product to market specifications of 60 percent K2O. An economic evaluation by the Bureau suggested that the rate of return on investment, after taxes, should be about 20 percent for such an enterprise.

Jan 1, 1980

By Bing W. Jong

A bench-scale evaluation of coal and coal waste materials as aggregate materials for use in longwall mine supports was undertaken as part of the Bureau of Mines Health and Safety program on ground control. Performance data were obtained on portland cement concretes (PCC) prepared with coal and coal wastes as aggregate materials. The effects of high-early-strength accelerators on strength and creep and of superplasticizers on strength properties of PCC formulated with coal and coal waste were investigated. Concrete formulated with a high-early-strength accelerator and coal and coal waste has 20 and 40 pet greater compressive strength, respectively, than the control samples without admixture. A concrete formulated with coal waste and the high-early-strength accelerator, using four bags of cement per cubic yard and a water-cement ratio of 1.0, had the lowest creep value of all the coal- and coal-waste-formulated PCC's tested.

Jan 1, 1983

By W. H. Somerton

Many oil-producing formations contain significant amounts of clay. Because of the large surface area and reactivity of such surfaces, the response of the formations to various recovery processes may be dominated by the reactions of fine-grained minerals, including clay minerals, in the formations. Thus, the success or failure of enhanced oil recovery (EOR) methods may be controlled to a large extent by the amount and nature of these minerals in the formations to which the methods are being applied. One of the deterrents to the successful application of chemical EOR methods is the loss of chemicals injected into the formation, to non-oil recovery processes. These chemical loss processes include adsorption onto mineral surfaces, chemical reactions with rock and fluids in the formations, possibly leading to precipitation and plugging of the formation, and trapping of chemicals in parts of the rock structure so that they become unavailable for displacing oil. Chemicals that may be injected include surfactants, polymers and caustic solutions which react with organic acids in the crude oil to produce surfactants in-situ. These losses are most pronounced in fine-grained reservoir rocks containing substantial amounts of clays.

Jan 1, 1984

By C. B. Davison

One goal of the Bureau of Mines is to conserve the Nation's mineral resources by developing improved performance materials. Consistent with this goal, the Bureau conducted studies on the formation of undesirable cristobalite in seven different fire clays used as refractories. The studies employed scanning electron micrography, chemical and X-ray analyses, and pyrometric cone equivalent determinations to examine the sample clays and determine the effect of thermal history and stablilizing additives on the amount of cristobalite in various calcines. This research has indicated that as fire clay calcining temperatures increased from 1390° to 1,490° C there was a gradual decrease in the percent of cristobalite present in the calcines and a progressive development of mullite crystallization. No cristobalite was found in fire clays calcined above 1,550° C, but cristobalite reappeared when the calcines were reheated to temperatures between 1,400° and 1,500° C. The research also revealed that additions of lithium fluoride (LiF) prevented formation of cristobalite in fire clay calcines.

Jan 1, 1979

By L. L. Hirst

In 1944, the 78th congress of the United States enacted Public Law 290, which directed the Secretary of the Interior, acting through the Bureau of Mines, to furnish industry with basic information and cost data for the development of a synthetic liquid fuels industry. Recently published information with respect to the cost of synthetic liquid fuels processes indicates a wide variation in estimated results. To clarify the results and inconsistencies for the hydrogenation of coal, the Bureau of Mines has prepared preliminary designs and calculated detailed investment costs from which the operating costs to produce 30,000 barrels per day of liquid products, mainly gasoline, by coal hydrogenation were obtained.

Jan 1, 1949