Search Documents

Determine what diameter piping is necessary to obtain sufficient water flow to spray nozzles used for dust suppression. Approach A simplified, diagrammatic method of calculating the flow of water through a proposed system consisting of a supply line and two banks of spray nuzzles is outlined. How It Works The pressure versus flowrate of the supply at the tapping point must be known or measured. The supply curve of typical city water at a 1 ¼ -inch pipe outlet is shown by the lowest curve in Figure 1. A supply curve for a typical pump fed from an open sump is shown by the middle curve. The combination of these, the supply curve of a pump fed by the city water supply is shown by adding the lower two curves to get the upper curve. A pump supply curve showing flowrate versus pressure is usually supplied by the manufacturer. The water supply line flow curve can be determined by measuring the time required to fill a 55 gallon barrel at various valve settings to determine flow, and by measuring corresponding pressures at the valve with a gauge.

Jan 1, 1979

By C. C. Shale

A semicommercia1, high-temperature electrostatic precipitator and adjunct equipment are described, and operating characteristics at 1,470° F and 80 psig are presented for both positive and negative polarity. Removal efficiency for negative corona waS about 91 to 96 percent while that for positive corona was only about 75 to 77 percent. Results are compared with those from bench-scale investigations, and equipment limitations are discussed. Theoretical aspects of the precipitation process are related to the operating characteristics.

Jan 1, 1969

By John C. Edwards

To have the capability to predict the development of localized spontaneous heating within a porous coalbed that is subjected to forced air ventilation or in an otherwise quiescent environment in which buoyancy develops, the Bureau of Mines developed three time-dependent mathematical models, which were used to calculate the temperature increase associated with chemisorption of oxygen by the coal. In each model, spontaneous heating is driven by an Arrhenius first-order reaction between the oxygen and coal. Two models are two-dimensional, and one is one-dimensional. In the first two-dimensional model, a constant-velocity forced convection airflow is specified; and in the other, buoyant flow is allowed to develop in the absence of forced convection. The third model evaluates the airflow from Darcy's law and a specification of the pressure at the surface of a one-dimensional porous coalbed. Numerical computations demonstrated how each model could be used to predict the onset of spontaneous heating when the porous coalbed was subjected to constraints of an imposed internal heat source or a high- temperature airflow. The effects of particle size and coalbed compaction upon spontaneous heating were examined with the third model.

Jan 1, 1990

By I. D. Shah

Thermal decomposition of copper (II) sulfate (CUS04) and copper (II) oxy-sulfate (CuO?CUS04) are important steps in the overall oxidative roasting of covellite (CuS) and chalcocite (Cu2S). Nonisothermal thermogravimetric techniques were used to investigate the decomposition reactions in flowing Na and air. Thermal decomposition of CUS04 and CuO?CUS04 followed "linear" kinetics with an apparent activation energy of 55±2 and 66±3 kcal per mole decomposed, respectively. These apparent activation energies comply with those previously reported when isothermal kinetic techniques were used. The addition of oxygen decreased the rate of decomposition, while small amounts of iron which were admixed with CuO?CUS04 did not have a significant effect. Neither oxygen nor iron had any appreciable effect on the apparent activation energy of the decomposition reaction.

Jan 1, 1972

By Paul B. Harder

Round Mountain Gold (RMG) in central Nevada, reports that over a nine-year period and a million operating hours, its fleet of 150-ton and 190-ton haul trucks has averaged better than 93% availability, with some of the trucks approaching 70,000 operating hours. Repair costs have been far below industry averages. Mine operations manager Pete Kesl credits the high availability and low repair costs to a succession of Product Support Agreements between RMG and Caterpillar dealer Cashman Equipment. He adds that good equipment and a high level of trust and co­operation between all parties to these agreements have been essential to their success at Round Mountain.

Jan 1, 1998

This report describes magnetic field measurements in the Helvetia Coal Co. Lucene #8 Mine for purposes of deriving a mapping of the magnetic field strength covering the major haulageways which contain conductors. The measurements were performed by Terry S. Cory, P.E. under U.S. Bureau of Mines purchase order P0372716. Assisting in performance of the measurements were personnel from the Bureau of Mines, PMSRC, and Helvetia Coal Co. Acknowledgement is given to Engineer Tom Strong of Helvetia Coal Co. who accompanied the measurement team and who lended support in performing the measurements and in supplying valuable engineering information for use in evaluation of the results. The results of the testing at medium frequency show that coverage of the entire mine area containing conductors can be achieved employing wireless radio techniques whereby radio signals are coupled into and are carried by these conductors. These results confirm earlier qualitative testing of the Collins Mine Wireless Radios in this mine. These results, performed over the frequency range 71-2890 KHz, illustrate the effect of frequency on the radio propagation with the conclusion that the best overall coverage is obtained at frequencies approximating 1000 KHz. This report presents all the raw data and the reduced data in the form of magnetic field strength contour maps. Sufficient information is provided to enable independent reduction of the data. A summary of observations which can be made directly from the contour maps is given.

Jan 9, 1977

By Richard J. Mainiero, Michael J. Sapko, Marcia L. Harris

Since 1988, there have been 17 documented incidents in the United States and Canada in which carbon monoxide (CO) is suspected to have migrated through ground strata into occupied enclosed spaces as a result of proximate trench blasting or surface mine blasting. These incidents resulted in 39 suspected or medically verified carbon monoxide poisonings and one fatality. To better understand the factors contributing to this hazard, the National Institute for Occupational Safety and Health (NIOSH) carried out studies in a 12-foot diameter sphere to identify key factors that may enhance the levels of CO associated with the detonation of several commercial trenching explosives. The gaseous detonation products from emulsions, a watergel, and ANFO blasting agents as well as gelatin dynamite, TNT, and Pentolite boosters were measured in an argon atmosphere and compared with those for the same explosives detonated in air. Test variables included explosive formulation, wrapper, aluminum addition, oxygen balance, and density. Major contributing factors to CO production, under these laboratory test conditions, are presented. The main finding is the high CO production associated with the lack of afterburning in an oxygen poor atmosphere. Fumes measurements are compared with the manufacturer’s reported IME fume class and with the Federal Relative Toxicity Standard 30 CFR Part 15 in order to gain an understanding of the relative toxicity of some explosives used in trench blasting.

By E. J. Kloos

Bureau of Mines-approved self-contained breathing apparatus of the compressed air demand type were evaluated for performance at low temperature. Apparatus durations, breathing resistances, and airflow rates were measured on machine tests at room temperature and -25° F. Man tests under actual wearing conditions verified the machine test results. Many serious functional changes in apparatus performance occurred at low temperature. Pressure regulators malfunctioned when diaphragms lost flexibility. Under certain conditions frozen condensed moisture sealed exhalation valves and fogged eyepieces. High-pressure leaks, not encountered at ordinary temperature, developed at low temperature. Tests results are discussed generally and specifically for each apparatus. Recommendations are given to obtain optimum performance from demand type breathing apparatus at low temperatures.

Jan 1, 1968

By C. W. Davis

"A copper-palladium-gold-silver ore is being mined at Salt Chuck, Prince of Wales Island, Alaska, from which a concentrate is produced that contains 40 to 50 per cent copper, and considerable amounts of palladium, gold and silver. There has been much difficulty in obtaining assays for palladium, gold and silver from the mine, smelter, sampler, and umpire that check within reasonable limits. While the results for copper content have not been unusual, the results for palladium have varied as much as 0c8 oz. on 3 oz. material, results for gold differed by 0.1 oz. on 1.6 oz. materials, and for a silver content of 7 oz., results differed by as much as 4.0 oz.The Bureau of Mines was requested to determine the causes of variation in the results of the different assayers, and to develop a satisfactory procedure for analyzing such ore.Three samples of concentrate were received for analysis, two small lots that had previously been assayed by the various laboratories, and one large sample. The large sample was dried and ground in a ball mill, put through a 150-mesh screen, and then returned to the ball mill for thorough mixing. The small samples were ground to pass a 150-mesh screen and then mixed on a mixing wheel.The large sample (No. 1) was analyzed by five different procedures, one of the small samples (No.2) by three procedures, and the other (No. 3) by two procedures (the two small samples being too small for further tests). The different procedures tried and the results obtained arc presented below. The samples of concentrate were from ore mimed and milled by the Alaska palladium Co. at Salt Chuck."

Feb 1, 1926

By William Wiehagen

This trainer?s guide is designed as a reference manual. The purpose is to offer information and examples to skills trainers to assist them in structuring training for new operators of Walk-Thru roof bolting machines. Trainers can use this manual as a resource for helping trainees learn, understand, and apply knowledge and skills. In this sense, the guide is not prescriptive. It is designed to offer information and trigger ideas on what might be done to accelerate learning to those who are new to the roof-bolting task. On-site trainers can modify this guide to fit their conditions, machines and equipment, and work procedures. They can integrate roof control plans, company policies and procedures, and operators? manuals from the manufacturers of the original equipment into this guide. Every trainee is different and will come to the job with varying levels of relevant knowledge and skills. The trainer?s decisions on where to start, how to organize the on-the-job and classroom training portions, and when and how to offer different aspects of the training will be based on (1) a pretraining assessment of the trainee?s knowledge and skills and (2) the trainer?s experience in conducting skills training. The ?Skill Check? section might be useful for deciding where training should start among miners who have underground experience but limited knowledge of roof-bolting techniques. Every job carries a learning curve and likely has a number of ?teachable moments? where significantly new knowledge and skills can be learned.

Aug 1, 2006

By Harold L. Rhodes

Vapor-liquid equilibria data for 65-34-1 and 25-27-48 mole percent helium-nitrogen-methane mixtures are presented for 12 temperatures from 76.5° to 164° K and pressures from 100 to 1,200 psia. These data were obtained in a windowed phase equilibria cell equipped with a vapor recirculating pump. Isobaric and isothermal K-values are plotted for both mixtures. Two isometric plots are included.

Jan 1, 1972

By William C. Laubengayer, Robert R. Godard, Harry Dobroski

A whole mine, computer-controlled communication and monitoring system for both normal and emergency use is installed and operating in the U.S. Steel Robena Mine complex near Uniontown, Pa. Portions of the system, including the coaxial cable and the key underground and surf ace phones, have been operating for over a year and a half. During this time the basic concept has been modified and new line amplifiers with directional switches have been developed to eliminate some problems in implementing the loopback feature. The quality of the audio and the availability of the system have been outstanding. Since early summer almost all subsystems have been completed. The experience with the telephone system itself, the pocket-pager call alert, section wireless radio, hoistphone, television, environmental monitoring, control and monitoring of equipment, voicedownlink/code uplink post disaster communications, post disaster through-the-earth monitoring, and the system center failure diagnostic routines are reviewed.

By Theodore Christos

The Bureau of Mines sponsored an investigation of the thermal oxidative degradation characteristics of certain solvents and hydraulic fluids used in underground mining operations. The following halogenated solvents were studied in view of their usefulness and their flame retardant property: tetrachloroethylene, C12C = CC12; 1, 1, 2-trichloroethane, CIH2CCHC12: and trichloroethylene, C12C = CHC1. The hydraulic fluids studied were representative of five groups approved by the Mine Safety and Health Administration for underground operation, namely: glycol-water solutions, mineral oil-water emulsions, synthetics other than phosphate esters, synthetic phosphate esters, and mixtures of phosphate esters with mineral oils and other ingredients. It was observed that the partially halogenated solvents present a greater potential toxic hazard than the fully halogenated materials, due not only to the easy production of hydrogen chloride but also to their ease of oxidation leading to the formation of phosgene and carbon monoxide. The pure phosphate esters exhibited the best thermal oxidative stability of the five groups of hydraulic fluids tested. A fluid containing phosphate esters mixed with mineral oils and other unidentified ingredients appeared to be the most hazardous On the basis that it produced very toxic acrolein and phosphine.

Jan 1, 1980

By Suzann C. Ambrosio

The mineral industry in Burundi continued to be a minor contributor to the 1980 gross domestic product (GDP) estimated at $293 million in constant 1970 prices.2 Mineral export revenues, primarily from cassiterite, increased by a factor of 15 between 1979-80, reaching approximately $434,000 by yearend 1980. Gold, bastnasite, colombite-tantalite, and wolfremite continued to be exploited on a small scale, using manual and semimechanical methods. Despite a sharp decline in mining activities during 1979, attributed to a lack o? profitability and shortage of construction materials, the mining sector exhibited signs of recovery during 1980. The mineral exploration budget grew 32% over 1979 levels and was equivalent to approximately $42,000 in 1980. In addition, the Burundi Geographical Institute (IGE BU) was created in September 1980 and given responsibilities to collect cartographic, topographic, hydrogeologic, and other geomorphological data., SONIBUROM, the Burundian and Romanian Government joint mineral corporation, conducted mineral deposit inventories during 1979-80 and has been charged with exploiting some of these as yet unspecified resource areas. Another Burundian-Romanian effort, called Mabaya-Butahana, was initiated to search for gold deposits. Meanwhile on the Ruzizi plain, alluvial gold prospecting, with an estimated grade between 0.2 to 1.0 gram per ton, was carried out on a small scale.

Jan 1, 1982

By Paul B. Harder

Round Mountain Gold (RMG) in cen­tral Nevada, reports that over a nine-year period and a million operating hours, its fleet of 150-ton and 190-ton haul trucks has averaged better than 93% availability, with some of the trucks approaching 70,000 operating hours. Repair costs have been far below industry averages. Mine operations manager Pete Kesl credits the high availability and low repair costs to a succession of Product Support Agreements between RMG and Caterpillar dealer Cashman Equipment. He adds that good equipment and a high level of trust and co­operation between all parties to these agreements have been essential to their success at Round Mountain.

Jan 1, 1998

By J. H. Russell

As part of its efforts to maximize resource recovery, the Bureau of Mines conducted studies to recover valuable byproducts from Western phosphate beneficiation tailings. Potential byproducts include phosphorus, vanadium, and uranium. The objective was to determine roasting and leaching conditions for maximum dissolution of vanadium from tailings containing approximately 13 pct P205 and 0.23 pct V. Sulfuric acid leaching tests were conducted with the tailings either as a dilute suspension dried, or in a roasted condition with or without NaCl added during roasting. More than 90 pct of the vanadium was dissolved by roasting at 850° C for 120 min with 8-pct NaCl and leaching at 75°C for 120 min with an excess of 2N H2S04, By roasting without NaCl and avoiding the difficulties of the chloride impurity, nearly 80-pct vanadium dissolution was achieved with an 800° C roast for 180 min. Quadratic regression equations were derived to relate vanadium dissolution to roasting and leaching conditions.

Jan 1, 1982

By L. A. Haas

The feasibility of removing sulfur dioxide by carbon monoxide reduction in a fixed-bed catalytic reactor was investigated by the Bureau of Mines. The reduction rate of sulfur dioxide with carbon monoxide was significantly dependent upon the iron and alumina content of the mixed catalyst. Maximum catalytic activity was obtained with about 40 percent iron-alumina mixture with a nominal gas mixture of 10 percent carbon monoxide, 5 percent sulfur dioxide, and the balance nitrogen. The synergistic effect of this catalyst mixture was explained by a dual reaction site mechanism, with both iron and alumina augmenting their specific sites at their interparticle contacts. The catalytic activity also increased with decreasing catalyst pellet size. With O.7-mm pellets, the entire pellet appeared to be catalytically active in a 2-gram catalyst bed. The apparent activation energy of the reaction was 18.3 kcal per mole in the temperature range of 350° to 600° C. Carbonyl sulfide (COS) was produced by the interaction of carbon monoxide and sulfur. The amount decreased with decreasing CO concentration. The ratio of COS formed per SO2 removed reached a maximum at about 400° C. The reaction rate appeared to be independent of S02 concentration in the range of 0.2 to 16 percent. The rate, however, increased directly with the CO concentration in the range of 5 to 20 percent. The presence of CO2 (<15 percent) had no appreciable effect on the rate. However, not over 0.5 percent oxygen could be tolerated. This method appears feasible for removing S02 from waste gas if the oxygen is removed prior to the catalytic S02 reduction process.

Jan 1, 1971

By Michael S. Wieland

The work-principle from thermodynamics was used to formulate a model for predicting toxic fumes from mining explosives in underground chamber tests, where rapid turbulent combustion within the surrounding air noticeably changes the resulting concentrations. Two model constants were required to help characterize the reaction zone undergoing rapid chemical transformations in conjunction with heat transfer and work output: a stoichiometry mixing fraction and a reaction-quenching temperature. Rudimentary theory with an unsteady uniform concentration gradient was taken to characterize the combustion zone, yielding 75% for the mixing fraction. Four quenching temperature trends were resolved and compared to test results of ammonium nitrate compositions with different fuel-oil percentages (ANFO). The quenching temperature 2345 K was the optimum choice for fitting the two major components of fume toxicity: carbon monoxide (CO) and total nitrogen oxides (NOx). The resulting two-constant model was used to generate comparisons for test results of ANFO compositions with additives. Though respectable fits were usually found, charge formulations which reacted weakly could not be resolved numerically. The work-principle model yields toxic concentrations for a range of charge formulations, making it a useful tool for investigating the potential hazard of released fumes and reducing the risk of unwanted incidents. Keywords: Toxicity; Fumes; Explosives

Objective To develop and evaluate the effectiveness of safety training tools specific to underground metal/nonmetal mining. Background In a series of stakeholder meetings held in the western United States beginning in 1998, participants identified a critical lack of appropriate training materials applicable to metal/nonmetal mining. Participants in the meetings provided many insights into what types of training materials are most effective in dealing with both experienced and inexperienced miners. Most important was that the materials should be realistic and interesting and that some way should be found to capture the wisdom and expertise of older miners before they retired. In response, training videos that focus on safe practices during the mining cycle are being produced. Two videos one on handling explosives underground and one on identifying roof hazards and proper scaling techniques were completed during1999, and a third video is now available. This video, entitled “Ground Support...It’s Important, or Miner Mike Saves the Day,” presents information on why ground supports work and how to install them properly. Approach The new video, “Ground Support…It’s Important,” presents a scenario in which two young miners make a bad decision to leave some supports out in order to catch up in their mining cycle. An expert miner, “Miner Mike,” sees this potentially disastrous situation and educates the young miners about what could happen if they continued to leave supports out. He introduces the young miners to several expert miners, who explain how to install different types of supports correctly, as well as share what experience has taught them over the years. How It Works All footage was taken in operating, underground mines, using14 experts to provide the teaching. Because of the wide variety of supports used underground, it was necessary to focus on those types more common to hard-rock mining. While more complex support systems, such as shotcrete and cable bolts, are mentioned, detailed material is not included. In the course of educating young miners Jeff and Jason, Miner Mike provides information on— •Why supports are necessary in underground mines. •The main types of supports commonly used in underground hard-rock mines. •How supports work. •How holes for bolts are drilled correctly using jacklegs, drill jumbos, and bolting jumbos.• How wire mesh, wire panels, metal mats, and different types of bolts, including mechanical bolts, friction bolts, grouted bolts, and cable bolts, are installed properly. •How to recognize that supports have failed and what to do about it.

Jun 1, 2000

By A. May

Florida has accumulated about 400 million tons of phosphogypsum, a mineral process waste generated in the production of fertilizer, and is adding 30 million tons to this annually. To minimize storage of this waste and reduce potential environmental effects, the Bureau of Mines conducted research into utilizing the phosphogypsum, by identifying and developing high-volume uses for this material. Admixtures of phosphogypsum, fly ash, and lime that could produce a coarse aggregate suitable for road construction were investigated. Using phosphogypsum with asphalt, cement, cement-kiln dust, silica, clays, and oxychlorides to pro-duce aggregate was also examined.

Jan 1, 1985