Search Documents

By A. C. Smith

The U.S. Bureau of Mines developed an experimental method to evaluate the relative effectiveness of water additives on the extinguishment of coal fires. The experiments were conducted in the fire zone of the multiple-entry section of the Bureau's Bruceton Experimental Mine. Four-hundred-pound Pittsburgh Seam coalbeds were ignited and allowed to burn until well-developed fires were achieved. Extinguishing agent-water solutions were then applied to the fires, and the quantity required to extinguish the fires was compared with the quantity of water alone required to extinguish similar fires. A 20% diammonium phosphate-water solution required an average of 5.8 gal to extinguish the coal fires, while two commercially available additive-water solutions required an average of 8.1 and 8.0 gal, respectively. The average amount of water required to extinguish the fires was 7.4 gal. An analysis of covariance, using the thermal energy of the coalbed to quantify the fire at the time of extinguishment, showed that the diammonium phosphate-water solution was slightly more effective at extinguishing these coal fires than water alone, and the two commercially available additive-water solutions were statistically equivalent to water alone.

Jan 1, 2010

By M. F. Dunn

The objective of this work was to define jet fan performance in d variety of large cross-section underground mine applications and to develop guidelines for thin performance in open airways, dead headings, and multiple face areas. Measurements include common ventilation instruments, continuous recording remote electronic anemometers to measure air velocity, and sulfur hexaflouride tracer gas with chromatograph analysis to determine dilution rates and air recirculation. For open airways the following were determined: Large jet fans are leas efficient in smaller airways, but quite effective in larger open airways for achieving both uniformity end greater air entrainment, when inclined about 10° or elevated. For dead headings the following were determined: The jet fan must be placed against the rib of the heeding closest to the incoming airstream from the crosscut or recirculation will increase. The fan should be placed at the pillar corner to increase airflow. As the fan is moved closer inby, recirculation increases. Larger fans promote recirculation. Inclining fans about 12° improves airflow in large headings. For face areas the following were found: For panels having uncontrolled airflow, the fan should be placed in the incoming airflow, about one pillar inby, and directed diagonally across the faces. For panels having narrower rooms and controlled airflow, the fan should be placed alongside the panel side in the first room so as to direct or intersect the incoming airflow at the next entry or crosscut.

Jan 1, 1983

By J. P. Bennett

The Bureau of Mines investigated the dimensional changes of ceramic materials exposed to acid environments to evaluate construction materials for emerging technology in chemical and metallurgical processes. Six commercial ceramic materials (two red shale, two fireclay, one silica, and one silicon carbide (SiC» were exposed to H20, 20 and 30 wt pct HCl, 40 and 60 wt pct HN03, and 10 and 50 wt pct H2S04 at temperatures from 50° to 90° C for 300 days. Linear expansions ranged from a low of -0.02 pct for the silica to a high of 0.45 pct for the red shale. A general ranking of the volume expansion of the materials tested, (from high to low), is as follows: high-porosity red shale A and fireclay B » low-porosity red shale B and fireclay A > silicon carbide and silica. A general ranking (largest to smallest) of the effect of exposure environments is HCl > H2S04, HN03 > H20. An autoclave test method was evaluated. Data obtained from 8-to 24-h exposures were compared with data obtained from the 300-day exposures. The relative expansion trends were similar, indicating that this method could be used as an accelerated test.

Jan 1, 1988

By C. C. Shale

Current-voltage relationships for air at high temperature in negative corona are compared with relationships predicted by theory. Deviations are discussed. Eased on the latest theoretical concept of electron detachment from negative ions and recent findings in basic research on free electron gases, results of applied research show the existence of free electrons in air at high temperature and high field strength-to-pressure ratios.

Jan 1, 1967

By F. A. Rutledge

"The W. E. Dunkle mine, sometimes called the Costello Creek coal mine, is 8 miles N. 20° W. of Colorado Station on the Alaska Railroad. The presence of coal in this area has been known since the district was extensively pros¬pected for gold between 1911 and 1915. At that time, coal from this deposit was used by miners for blacksmithing. The increased demand for coal resulting from government defense projects in Alaska led to exploitation of this deposit in 1941.The inability of Alaska coal mines to supply the quantity of coal required by public and private consumers and by the armed forces in Alaska was responsible for establishment by the Army of the Coal Procurement Section of its Alaska Department. It proposed to investigate the deposits and to expedite production from the Alaskan coal fields. The Bureau of Mines closely cooperated in this program.The quality of the Dunkle coal and the favorable location of the deposit caused it to be one of the properties chosen for investigation under a joint Army-Bureau of Mines-Geological Survey program.During July 1943, the coal area in the immediate vicinity of Costello Creek was geologically and topographically mapped. by Clyde Wahrhaftig and Jacob Freedman, geologists, U. S. Geological Survey. F. A. Rutledge, mining engineer of the Bureau of Mines examined the property July 18 to 22, 1943, and a project of trenching, diamond drilling, and sampling was initiated on August 4, 1943. During the project Clyde Wahrhaftig remained at the Dunkle mine to interprets drill cores and assist the author in planning the explora¬tory program. The project was completed October 7, 1943.Field investigations were under the general direction of R. S. Sanford, acting chief, Alaska Branch, Mining Division. Coal analyses were made by Maurice L. Sharp, coal analyst for the Alaska Railroad.Special mention is made of the cooperation and assistance received from Clyde Wahrhaftig, geologist, U. S. Geological Survey.The many courtesies received from the owner, W. E. Dunkle, and the members of the Army Coal Procurement Section, Alaska. Department, also are acknowledged.The W. E. Dunkle coal mine is in the Broad Pass region on the south slope of the Alaska Range at an altitude of 2,800 feet (fig. 1). It is situated within the Third Judicial Division, headquarters of which is Valdez, Alaska. The area is situated approximately at latitude 63° 15' N. and longitude 149° 30' W. and is connected with the Alaska Railroad at Colorado Station by an 11-mile gravel road that is passable throughout the year. This road is maintained by the Alaska Road Commission. A private telephone line to Colorado Station connects with the telephone and telegraph service of the Alaskan Railroad.The passenger rate from Anchorage, Alaska, to Colorado station is $12.10. Freight rates are $1.60 a hundred pounds for heavy machinery and $2.66 a hundred pounds for first-class freight.The Costello Creek coal basin is in an area of low relief and has been dissected by numerous creeks flowing down the south flank of the Alaska Range. The Dunkle coal mine is on Coal Creek, a small tributary of Camp Creek, 1,000 feet from their junction. About 700 feet below this junction, Camp Creek joins Costello Creek, which in turn empties into Bull River 1/2 mile above the latter's confluence with the West Fork of the Chulitna River. The location of the mine is shown on figure 1."

Oct 1, 1948

By C. H. Schack

Although viscosity is known to be important in processing and handling finely ground urea, its effect has never been fully quantified. This report describes the methods used and the results obtained in the initial phases of a broad investigation of the influence of viscosity of water suspensions of minerals in flotation, thickening, filtering, and other mineral-dressing unit operations. Several types of vis-cosimeters were tested before reliable and reproducible results could be obtained on mineral suspensions. After the viscosimeter used in the research was calibrated and standardized, tests were made on six pure minerals to study the relationship of pulp density, particle size, crystallinity, and cleavage on viscosity. An orifice-type viscosimeter equipped with a mechanical stirrer gave as good results as other types and was more flexible, faster, and simpler to operate. The orifice-type viscosimeter, when calibrated and standardized with glycerin and water mixtures, proved satisfactory over a wide range of viscosities. The accuracy and reproducibility were reasonably constant between 1 centipoise and 200 centipoises, the anticipated range in common mineral-dressing unit operations.

Jan 1, 1957

By Robert W. Ageton

Optimal planning for mining the deep, lead-zinc-silver deposits of the Coeur d'Alene mining district, Shoshone County, Idaho, could be facilitated by a knowledge of the magnitude and direction of the pressure acting in the virgin rock. The distribution of primary stresses should be considered in order to prevent possibly destructive mining-induced stress concentrations. This particular investigation was concerned with determining stress in a zone 4,000 feet below the surface and known to be ender stress concentrations due to mining operations. Disking of the stress-relief cores obtained in a vertical down hole permitted qualitative evaluation from visual observations; the results indicate that a high lateral stress existed at the time the measurements were made. Stress-ellipsoid determinations gave a compressive principal stress of -13,000 psi oriented about N 45° W and nearly horizontal, a compressive principal stress of -11,000 psi oriented about S 45° W and abut 60° off the vertical pointing away from the vein, and a compressive principal stress -5 -7,000 psi oriented N 45° E and about 60° off the vertical, pointing toward the vein. Subsequent to the overcoring stress-relief drilling, a rock burst occurred about 100 feet northwest of the test site.

Jan 1, 1967

By Curtis D. Edgerton

Miami Oölite limestone is the only significant construction mineral in southeastern Florida. Its source area coincides with that of rapid urban expansion. Two-thirds of the existing resource is already unavailable because of development. Land-use conflicts place future availability of limestone in jeopardy. However, a sufficient limestone resource to meet demand for many years is present if its extraction is not restricted. Adverse environmental effects of quarrying Miami Oölite are not severe; land values often increase following quarrying. Future availability depends upon--(l) achieving uniformity of Federal, State, county, and municipality statutory requirements governing quarry operations; (2) setting aside specific land areas for future quarrying; and (3) cooperative planning to provide for land utilization upon completion of quarrying.

Jan 1, 1974

By F. E. Brantley

Blister copper was successfully deoxidized with any of a variety of reducing gases; lancing techniques or a vertical-column furnace were used to contact the copper and gases. Of the gases tested, butane, when used to lance molten copper at about 1,200° C, reaction temperature, was slightly more effective than propane, natural gas, carbon monoxide, or reformed gas for deoxidizing copper from about 1.0 to less than 0.1 percent oxygen content, Laboratory-scale tests revealed that the vertical furnace, composed of a heated column packed with silicon carbide chips or hollow carbon cylinders, was significantly faster and more efficient than the lancing technique for deoxidizing molten copper with any of the gases tested. Comparison of the gaseous-reduction method with the conventional poling method suggests that the gaseous method has important technical and economic advantages for deoxidizing blister copper to any readily controlled amount of residual oxygen content.

Jan 1, 1962

By Graham W. Marks

The general positions of the absorption maxima of aqueous solutions of the violet and green isomers of chromic sulfate the visible spectral region have long been known, but, to the knowledge of the writer, no comprehensive studies have ever been made. To gain further knowledge concerning these inorganic complexes and to investigate the possibilities of developing an analytical method for determining the concentrations of the violet and green isomers in a mixture, a more complete investigation was made in the spectral range from 325 to 850 millimicrons.

Jan 1, 1951

By F. E. Block, Stephen D. Hill

The necessity for measuring radiation dose is encountered in studying both the beneficial and damaging effects of ionizing radiation on materials . It is also necessary to know the radiation dose absorbed by the reactants in order to evaluate the efficiency of reactions or processes that are promoted by radiation . Thus , a significant effort was made at the Albany cobalt 60 facility to investigate techniques by which the exposure radiation dose can be determined . Methods including ferrous sulfate , ceric sulfate , and methyl methacrylate chemical dosimeters , ion chamber dosimetry , and an absolute radiation calorimeter were investigated . Isodose curves were constructed for several standard source configurations using the dosimetry techniques which were investigated .

Jan 1, 1964

By A. B. Needham

This paper, which describes mining practices at a mine in the Cave- in-Rock, Illinois, fluorspar district, is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. Ore deposits in the southern Illinois-western Kentucky fluorspar dis- trict are of two general types (1) the flat-bedded, lenticular replacement and (2) the relatively narrow, rather steeply dipping fault or fissure filling. This paper describes production methods used and results obtained in mining one of the bedded lenticular ore bodies that are prevalent in the northeast portion of the district near Cave-in-Rock.

Aug 1, 1949

By S. P. Sandoval

Previous research by the U.S. Bureau of Mines demonstrated that nonionic surfactants increased the leaching rate of copper in the flask leaching of chalcopyrite with ferric sulfate if sufficient ferric sulfate was present. This research was continued by the Bureau in Part 2 to further explore the application of nonionic surfactants to the dump leaching of chalcopyrite. A polyoxyethylene lauryl ether was selected as the superior nonionic surfactant tested at 25° and 50° C. The addition of the surfactant increased copper leaching by 116 pct at 25° C and 1.0 pct solids and by 61 pct at 50° C and 0.5 pct solids at Fe 3+ concentrations greater than 1 g/L. At 0.1.0 g/L Fe 3+ and below, the addition of the surfactant produced as much as a 35 pct decrease in leaching. Each of the nonionic surfactants studied was found to be heavily adsorbed by a typical chalcopyrite ore, which poses a serious barrier to the application of nonionic surfactants in an actual chalcopyrite dump.

Jan 1, 2010

By Larman J. Heath

Liquid incendiaries were burned within the interstices of several different types of sandstone cores to determine the technical feasibility of increasing sandstone permeability by this method. Fuel-oxidant mixtures were tested in 186 cores; six cores exploded when ignited. In virtually all instances, the explosion completely pulverized the sandstone cores. In addition n those cores damaged by explosions, 24 cores were fractured so severely that permeability tests were impossible. Although combustion gener¬ally increased the permeability, specific mixtures at given pressures were inconsistent in their ignition and burning behavior. Tests indicated that the heat of burning incendiaries significantly increased sandstone permeability. The improved permeability ratios were usually less than 2, but one was 10.3. Permeability alteration by other in situ methods was not as effective as that by flame propagation.

Jan 1, 1971

By G. E. Rennick

An oil well penetrating the Pittsburgh bituminous coalbed in northern West Virginia was plugged and safely mined through 3 months later. A sensitive chemical tracer, introduced into the oil reservoir before the test, was not detected in the mine air following the plugging and during mining of the pillar and penetration of the well. Effectiveness of the plugging in preventing reservoir gas from entering the mine through the well hole was verified by continuous monitoring of the mine air for indications of sulfur hexafluoride, an inert gas detectable in amounts as minute as 1/2 part per billion. Expandable cement and fly ash-gel-water slurry were utilized to seal the well above and below the coal seam. Three other wells were also plugged using various techniques.

Jan 1, 1972

By Lawrence K. Requa

The property being worked by the Lewiston dredge of Placer Development (Ltd.) is on the Trinity River in Trinity County, Calif., about 9 miles north of the town of Lewiston (see fig. 1). The nearest rail point is at Rending, Calif., which is exactly 50 miles bar road from the dredge camp. Recently a very good section of State highway has been constructed from Redding to Weaverville, and it is now possible to use this highway for 35 miles of the distance between the dredging property and Redding. The remaining 15 miles, however, are over ordinary dirt road. No trouble is experienced in reaching the property except for a few weeks during the middle of the winter when snowstorms may make travel difficult but not impossible. At present the property consists of about 500 acres of patented land, which extends for about 3 miles along the main Trinity River and Stuart's Pork. It is being worked with one 7-cubic foot, Bucyrus-type dredge, which has an average monthly capacity of about 100,000 cubic yards. To the end of 1931 approximately 10,000,000 cubic yards of gravel had been dredged.

Jan 1, 1932

By Thomas M. Barczak

This U.S. Bureau of Mines (USBM) report evaluates the load supporting characteristics of grout columns used as point supports for mine subsidence abatement. The cone-shaped columns were constructed with sodium silicate and cementitious grout in both wet and dry environments. The scope of work included the testing of seven full-scale grout columns in the USBM's Mine Roof Simulator from which the load-deformation and failure characteristics were determined. The performances of grout columns are analyzed with respect to (1) the amount of roof contact established during column construction, (2) shape effects produced by the truncated cone geometry, (3) size effects in reference to grout strength and full-scale column capacity, (4) the effect of wet environments on grout strength, (5) the effect of the sodium silicate on the grout strength and full-scale column behavior, and (6) the stiffness of the grout column. Limited tests were also conducted on cylindrical columns constructed in fabric bags. Recommendations for point support construction using sodium silicate technology and the need for additional research to develop improved containment devices for column construction are addressed in the report.

Jan 1, 2010

By G. Richards Gwinn

In modern warfare, mica is truly indispensable. Coordination of combatant units necessitates maintenance of intricate communications equipment, in the construction of which high-grade sheet mica is essential. Scrap, ground, and the poorer qualities of block mica, which are less essential to the military program, are not considered in this paper. Furthermore, as the paper is designed primarily to assist mica miners, mica derivatives, Such as splittings and films, also are excluded from discussion. The paper therefore relates solely to block mica of strategic quality. Understanding of t e many factor involved in marketing mica is definitely advantageous to mica, miners. The nature and detrimental effects

Jan 1, 1943

By G. R. Hopkins

Although many small refineries were dismantled in 1934 the total number of plants, including a few under construction, increased from 604 at the beginning of the year to a new high of 638 on January 1, 1935. The capacity also reached a new record, the total of 4,072,400 barrels of crude oil daily being about 45,000 barrels higher than the previous high of January 1, 1932. The number of refineries increased materially in 1933, following construction in east Texas and the building of many small plants in the Rocky Mountain district and elsewhere. Most of the new plants of 1933 were built to provide an outlet for crude or because the ratio between crude oil and gasoline prices appeared conducive to profits However, low gasoline prices and increased costs in 1934 dispelled the hopes for profits; many plants were shut down, and some were dismantled. The number of operating plants declined from 454 on January 1, 1934, to 435 on January 1, 1935, but the number of inactive plants increased from 137 to a new high of 196 during the same period. As indicated above, new construction was at a minimum in 1934, and on January 1, 1935, only 7 plants were being built.

Jan 1, 1935

This is the fourth in a series of reports on properties of commercial motor fuels, made in accordance with a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of Mines of the Department of the Interior. The first report gave data on motor gasolines sold during the winter of 1935-363/. The second report gave the same data? for motor gasolines sold during the summer of 19364/. The third report of the series gave the same data for motor gasolines sold during the winter of 1936-375/. This report covers 63 brands of gasoline represented by 1,136 samples excluding the Pacific Coast. Those from the Pacific Coast were averaged by the Pacific Coast technical group before being submitted and are published exactly as they were submitted. In some areas reports were received from five or six companies on the same brands of gasoline, whereas in other areas only one company reported on a brand. Thus, it can be seen that some of the data are more representative than others.

Jan 1, 1937