Search Documents

By R. Y. Williams

In this report an attempt is made to discuss the first cost of each of several types of mine-ventilation stoppings, as well as the total annual expense of maintaining a stopping during its required period of service. Such data furnish a basis for comparison of the efficiency of the different types, and are of great importance to an engineer planning the development of a mine. The data given were obtained through an investigation conducted under a cooperative agreement between the Bureau of Mines, the Illinois State Geological Survey, and the department of mining engineering of the University of Illinois. The report itself is published by the Bureau of Mines as a contribution to the literature on safety and efficiency in coal mining.

Jan 1, 1915

By T. E. Gray

This report describes the preparation characteristics of the signifi¬cant coalbeds in Preston County, W. Va. It is one in a series of reports planned to determine coals suitable for the production of metallurgical coke, either as mined or after beneficiation. Over 2 million tons of coal was produced in Preston County, W. Va. in 190, none of which was cleaned mechanically. Estimates as of January 1, 1959, indicate that more than 3 billion tons of coal remained in the county in beds 12 inches or more thick. The Bakerstown, Mahoning, Upper Freeport, and Upper Kittanning beds were selected by the Bureau of Mines for study based on current production and estimated minable reserves. Sample locations were selected after study of the literature, conferences with mining engineers and mining company offi¬cials in the field, and examination of available sites. Four samples were collected from the Bakerstown and Upper Freeport beds and one each from the Mahoning and Upper Kittanning beds.

Jan 1, 1961

By Foster Fraas

This report describes the application of pulsed magnetic fields derived from alternating and intermittent magnetizing currents. Application of such pulsed magnetic fields to the matrix-type separator permits (1) the complete discharge of the magnetic fraction with wet feeds and (2) the dry separation at particle sizes down to 325 mesh. At smaller particle s indications are that frequencies above 60 hertz will be required. Applications of intermittent magnetizing current to the cross-belt separator give the cross-belt-separator an advantage over the conventional constant-field cross-belt and induced roll separators; the intermittent current enables the cross-belt separator to separate matted fibrous and magnetically coagulating feeds, a type of feed that occasionally occurs with mineral, industrial, and secondary materials.

Jan 1, 1973

By G. L. Gates

The Bureau of Mines in cooperation with the City of Long Beach) Calif.) studied some physical factors effecting the deposition of barium sulfate scale in oil-well rotary pumps. Freshly formed barium sulfate was obtained by combining sulfate in sea water with barium from a barium chloride solution. The rate of scale deposition was measured quantitatively by weighing the pump impellers and diffusers. The results of the tests showed that coating the impellers with plastic significantly reduced the rate of barium sulfate deposition.

Jan 1, 1967

By Maurice Deul

A special short-term research project was initiated to develop plant design parameters for treating mine waters to yield an effluent acceptable for discharge into streams and a sludge amenable to effective and economic disposal. Neutralization was investigated to provide simple and direct treatment of ferruginous acid waters using lime; coarse limestone, and limestone followed by lime. Limestone treatment was accomplished using a small cement mixer as a simple reactor to provide abrasive agitation of limestone and mine water. Results from tests with nine mine waters encompassing a wide range of iron and acid concentrations showed that coarse limestone, one of the cheapest neutralizing agents known, is potentially useful for treating mine water discharges. However, process variables must be defined more completely before the practical applications and limitations of the process can be fully established. In all the tests a pH of >7.2 was obtained ultimately with limestone. Reaction time to reduce the iron content below 7 ppm in the water was dependent on the original ferrous iron concentration. For waters with high ferrous iron content, treatment with limestone followed by lime rapidly produced an acceptable treated water, Sludges with good settling and handling characteristics resulted when limestone was used for neutralization either alone or with subsequent treatment. Reaction rates are expressed graphically as pH change and iron depletion curves; characteristic solids settling curves are shown. The temperature dependency of ferrous iron oxidation was verified.

Jan 1, 1967

By B. B. Letson

The heats of formation of lithium chloride and lithium oxalate were determined with the aid of a Bureau-developed, glass Dewar-type solution calorimeter which uses thermistors as its temperature sensing element. Values obtained at 298.15° K were -98.38 ± 0.54 kcal/mole for lithium chloride and -329.02 ± 0.79 kcal/mole for lithium oxalate, using graphite as the standard state for carbon.

Jan 1, 1965

By E. J. Lintner

This paper is one of a series being prepared by the United States Bureau of Mines describing clay mining and crushing methods and costs at various operations throughout the United States. These papers are designed to disseminate technical information regarding methods used. The cost tabulations represent local operating expenditures only and not total production costs. It is recognized that publication of total production costs might perhaps, in many instances, cause embarrassment to the individual operator as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called to this distinction in order that no misunderstanding of the scope of the cost tabulation shall ensue. The following report deals specifically with the methods employed by the Camp Brothers Company, Mogadore, Summit County, Ohio.

Jan 1, 1936

By Stephen C. Tadolini

The Bureau of Mines conducted field investigations in two underground mines to determine the actual loads to which bearing plates were subjected when installed in conjunction with full-column resin-grouted bolts and the roof movements generated by the applied loads. Measured loads indicate that the bearing plate is an integral part of the support system. Vertical displacement gauges installed to monitor roof displacements in the test sites show that the highest degrees of loading occur in conjunction with the largest amounts of movement.

Jan 1, 1986

By E. Morrice

The Bureau of Mines investigated methods for beneficiating platinum-palladium ores from the Stillwater Complex, Montana. Results of bench-scale and pilot-scale studies employing froth flotation to recover sulfide concentrates containing platinum-palladium values from a serpentinized ore are presented. Best results in the pilot mill were obtained with a sodium isobutyl xanthate-normal dodecyl mercaptan col-lector combination at a natural pH of 8.2. A rougher concentrate con-taining 1.7 oz/ton Pt and 4.7 oz/ton Pd was prepared. Recoveries of platinum and palladium were 96 pet and 86 pet, respectively. Batch cleaner flotation of rougher concentrates yielded concentrates contain-ing 3.7 oz/ton Pt and 9.8 oz/ton Pd.

Jan 1, 1984

By Raja V. Rarnani, Robert L. Frantz

More than 100 scientists from diverse professional backgrounds have contributed their expertise to the Dust Center as investigators. Approximately 50 researchers served as principal investigators, with responsibility for directing the work on Center projects, from experimental design and implementation in mines and in laboratories to coordination of efforts within the research infrastructure of the Center. The professional biographies which follow demonstrate the breadth and depth of research capabilities brought to the Center by its principal investigators.

Jan 1, 1995

By E. G. Davis

The Bureau of Mines made laboratory-scale experiments to examine the technical possibilities of reclaiming manganese from slags produced by oxygen lancing of high-manganese pig iron. Ferromanganese was added to molten pig iron to yield a 4-to 5-percent manganese hot metal, which simulated a product obtainable from the blast furnace. This was injected with oxygen to reduce the metal to 1 percent or less manganese and form a slag containing about 40 percent manganese. The molten slag was water-quenched, treated with H2SO4) roasted at 660° C, and water-leached to give soluble manganese and iron sulfates. The sulfates were precipitated as hydroxides, converted to the oxide form, and smelted to produce a standard ferromanganese containing 74.6 percent Mn and 0.01 percent P. As an alternate method of manganese recovery, a manganese cell feed was prepared from the leach solutions and electrolytic manganese was produced. Direct smelting of the high-manganese slag resulted in 74.2 ferromanganese meeting ASTM specifications except for phosphorus content. The high phosphorus content of the metal and high slag-to-metal ratio obtained made this approach unattractive.

Jan 1, 1966

By K. E. Stanfield

One of the initial projects under the oil-shale research and development phase of the Synthetic Liquid Fuels Act, Public- Law 290, 78th Congress, approved April 5, 1944, was a survey of oil shales of the United States for the selection of a site for an oil-shale demonstration plant. The oil shales were assayed by the conventional Bureau of Mines retort method proposed by Karrick and described by Guthrie in a more recent publication. From previous experience and that had in making these assays, it became evident that the assay method should be modified or replaced by a more satisfactory one. There are several outstanding objections to the Bureau of Mines oil-shale assay method: (1) the oil yields are frequently smaller than those obtained by other types of assay equipment and by commercial retorts; (2) the assayed oil yield represents only a portion of the organic matter in the shale, which under more favorable conditions, may, Jae converted, more completely into oil; (3) the retorting procedure is controlled mainly by trial-and-error methods; and (4) the assay requires approximately 6 hours for completion.

Jan 1, 1949

By William D. Riley

In order to evaluate the corrosion resistance of zirconium in mineral extraction processes, such as a clay-hydrochloric acid leaching process for extracting alumina, the Bureau of Mines conducted corrosion studies in HCl-AlC13-FeC13 environments. A series of weight loss and electrochemical tests were conducted at 25° and 65° C in aluminum chloride (AlC13) plus hydrochloric acid (HCl) solutions containing 0 to 1,000 ppm ferric ion. It was determined that zirconium, which normally exists in a passive state in chloride-containing solutions, undergoes pitting attack in solutions containing more than 100 ppm of ferric ion. It is also shown that an oxide film prepared in air at high temperature offers protection in acid solutions containing levels of ferric ion from 300 to 1,000 ppm.

Jan 1, 1981

The object of this program was to extend the capabilities of visual paging systems both in size and function. The system developed uses the mine pager phone line for communication, monitoring, and remote control. A central station, using a minicomputer, transmits signals by phase inversion modulation of a 16,384 Hz carrier to as many as 999 remote units. The remote unit addressed returns An echo to indicate that it is functioning and, in the case of monitor units, to convey the monitor data. Magnetically latched display dis[c]s, which can be seen from both sides when posted, are used for visual paging. Lists of the addresses of posted pages, unanswered pages, and non-echoing units are prepared by the central station computer. The system was designed to be intrinsically safe and should operate for three months on a 12-volt lantern battery.

Jan 1, 1980

By W. B. Tarpley

This program was conducted to demonstrate the unique advantages of suppressing methane ignition in underground mines by use of Energy & Minerals Research Company's thixogel fire extinguishing system, which stably suspends dry powder extinguishing agent in thixotropically gelled liquefied gas extinguishant. As anticipated, the project demonstrated thixogel system advantages of: 1) capability to disperse state-of-the-art powders in thixogelled Halons; 2) non-agglomerating stability for dependable expulsion; 3) stability in storage for long shelf life; 4) virtually in¬stantaneous dispersion; 5) expansive cloud formation; 6) reach and re-forming around obstacles; 7) at least twice the extinguishant effectiveness; and 8) compatibility of use with Fenwal bottles and MSHA canisters. Thus, it should prove a superior explosion/fire suppressant for coal face cutters and triggered barriers, as well as for motorized equipment, electrical equipment and the like.

Jan 1, 1981

By Jack I. Paige

The Bureau of Mines conducted studies to provide data on the room temperature mechanical properties of Ti-6Al-4V alloy cast in waterglass-bonded zircon sand and to determine the effect of hot iso-static pressing (HIP) on these properties. Data on the cast and annealed Ti-6Al-4V alloy were compared with published data for forged and investment-cast Ti-6Al-4V alloy. The average Charpy V-notch impact strength compared favorably with the typical values of 17 ft?lbf for wrought material and 19.2 ft?lbf for investment-cast material. The room temperature mechanical proper-ties of cast and annealed material compared favorably with published values for investment-cast Ti-6Al-4V alloy and exceeded the specifications for (1) titanium and titanium alloy castings, grade C-5 according to ASTM B367-69, and (2) titanium alloy bars and forgings as specified in AMS4928H, except for the AMS4928H minimum requirement for reduction in area (25 pct). The minimum requirements are: tensile strength, 130 ksi; yield strength, 120 ksi (0.2 pct); and elongation, 6 pct. None of the specimens tested met the AMS4928H minimum requirement for reduction in area. The HIP process healed the internal casting porosity in the test specimens, but the fatigue strength was not significantly improved. The fatigue properties of both the cast and cast plus hot isostatically pressed castings were significantly lower than those of wrought products.

Jan 1, 1984

By J. F. Barkley

Two major problems in the operation of air preheaters for boilers are corrosion and the accumulation of deposits on the heating surfaces. Corrosion or loss of metal necessitates replacement of parts; the accumulation of deposits decreases the size of the gas and air passages, resulting in increased pressure drop for the same gas flow, and also affects the heat transfer. These items, either singly or together, limit the capacity and efficiency at which the equipment can be operated and affect its availability, even causing undesirable shutdowns under extreme conditions The field and laboratory work on regenerative air preheaters described in this report covers research on the relative corrosion resistance of different materials, such as various metals, special metal coverings, and fired clays, and studies on deposits, their nature, analyses, and corrosive effects. This is the first report on cooperative work of The Air Preheater Corp., of New York City, and the Federal Bureau of Mines.

Jan 1, 1953

By N. A. Eilertsen, Rolf S. Paine

The Bureau of Mines studied the presplitting technique used for controlling overbreakage in the walls of a vertical shaft at the U.S. Army Corps of Engineers Littleville Dam project near Huntington, Mass. The periphery of the shaft, the dimensions of which were 16-1/2 feet wide by 21 feet long and 52 feet deep, was presplit (cracked) in the solid to a depth of 48 feet prior to full-depth sinking. Presplitting prevented overbreak in a fairly soft schist and provided sound self-supporting walls which required very little scaling.

Jan 1, 1965

By D. H. Hileman

Economic investigations indicate that bituminous coal can be mined underground in the Uinta region and marketed at a cost competitive with that of other energy sources in the West. A selling price of $3.90 per ton of coal was calculated from a cost analysis of a projected coal mine in the Emery coal- field of Utah. Although mines in some of the coalfields have extremely difficult mining conditions and cannot compete in the energy market at this price level, at least two other coalfields in the Uinta region contain coal reserves that could be mined and sold at a price of approximately $3.90 per ton. Projections by power companies and other coal-consuming industries indicate a strong future market for the large coal reserves in the Uinta region.

Jan 1, 1970

By E. E. Donath, L. L. Hirst, L. C. Skinner

Two processes are available for the production of synthetic fuels from coal high-pressure hydrogenation and the carbon monoxide-hydrogen synthe- sis. This paper presents some ideas and new developments in coal hydrogen- ation that have been incorporated in an estimate for the production of 30,000 barrels per day of liquid fuels, mainly gasoline. A few comparisons of the processes will be helpful before discussion of the details of pro- posed improvements in the hydrogenation process. The principle of the high-pressure hydrogenation process ie the addi- tion of hydrogen at pressurea in the range of 3,000 to 10,000 p.s.i. to coal at elevated temperature and with the help of catalysts. On the other hand, the principle in the Fischer-Tropsch synthesis is the complete break-down of coal into a mixture of carbon monoxide and hydrogen, followed by the catalytic combination of these two gasse into hydrocarbons or suitable catalysts. For the synthesis, moderately elevated pressures of about 350 p.8.1. will bo used in the immediate future, although it can be carried on at atmosphoric pressure with certain catalysts. The products of these two processes using coal as raw material are almost as differont as hydrocarbons can be. The products of the high-pres- sure hydrogenation of coal reflect the original constitution of the coal. They are, therefore, rich in ring compounds, both aromatic and naphthenic, but, due to the action of highly comprcesed hydrogen and catalyst, are satu- rated and very stable. These constituents give the gasoline a high octane number and excellent rich-mixture performance, combined with good gum and storage stability. Therefore, this gasoline is suitable for aviation gaso- line or base stock. The Diesel fuel can be hydrogenated to a centane number of 45 or higher, which is entirely satisfactory for operating normal Diesel

Dec 1, 1948