Search Documents

By T. W. Johnson

One of the common methods of increasing recovery of oil from partly depleted oil sands is to inject natural gas, air, or air-gas mixtures into the sand, thereby supplying energy to move oil into the well bore. Where natural gas is not available, air or an air-gas mixture is used as the repressuring medium. Air-gas mixtures are obtained from the casing-heads of oil-producing wells in the areas repressured with air or air-gas mixtures and consist usually of varying amounts of the hydrocarbon gases, nitrogen, oxygen, and carbon dioxide. Laboratory experiments have been conducted by the Bureau of Mines to determine the effect of air on crude oils.4/ In these experiments the crude oils were oxidized by the air, and the degree of oxidation depended not only upon the chemical composition of the crude oil but also upon the duration and method of contact between the oil and air, the temperature of the fluids and the concentration of the oxygen. When the crude oils were oxidized the following results and changes in the oils were obtained:

Jan 1, 1937

By Ronald B. Stotelmeyer

This report summarizes studies of 28 National Forest roadless areas in Montana completed by the U.S. Bureau of Mines (USBM) in the period 1974-1993. It also briefly describes 20 areas for which field studies have not been conducted. All 48 of these roadless areas have been recommended for addition to the National Wilderness Preservation System or proposed as special management areas by the U.S. Forest Service (USFS) or the Montana congressional delegation. The Bureau studies indicate which parts of the roadless areas have a high likelihood for mineral-resource development. They also show where mineral production has occurred in the past and where abandoned mine workings (possible hazards) would be encountered. The number of mine and prospect workings found are a measure not only of surface disturbance, but of areas not wilderness in character. For the purposes of this report, mine refers to a property which produced (or is currently producing) a mineral commodity, a prospect is a property which has been explored but has no record of production.

Jan 1, 1994

By T. W. Johnson

One of the common methods of increasing recovery of oil from partly depleted oil sands is to inject natural gas, air, or air-gas mixtures into the sand, thereby supplying energy to move oil. into the well bore. Where natural gas is not available, air or an air-gas mixture is used as the repressuring medium. Air-gas mixtures are obtained from the casingheads of oil-producing wells in the areas repressured with air or air-gas mixtures and consist usually of varying amounts of the hydrocarbon gases, nitrogen, oxygen, and carbon dioxide. Laboratory experiments have been conducted by the Bureau of Mines to determine the effect of air on crude oils.4/ In these experiments the crude oils were oxidized by the air, and the degree of oxidation depended not only upon the chemical composition of the crude oil but also upon the duration and method of contact between the oil and air, the temperature of the fluids and the concentration of the oxygen. When the crude oils were oxidized the following results and changes in the oils were obtained:

Jan 1, 1937

By Nicholas P. Kripakov

The U.S. Bureau of Mines examined the applicability of existing material models to solve practical geotechnical mining-related problems by solving a yielding pillar stability problem considering confining effects on strength. Numerical difficulties normally encountered with modeling strain softening behavior were eased with a simplified computational procedure using a quasi-elastic approach to account for residual strength after initial failure. Although in agreement with a confined-core pillar design method using actual mine conditions that include mine layout geometry, overburden geology, and rock properties of the deposit and surrounding structure, the results cannot be verified because measured field data are not available at this writing.

Jan 1, 1981

By M. J. Brevoort

Research work in the Bureau of Mines cryogenic laboratory requires the use of high-sensitivity galvanometers of the d'Arsonval type in a building that is subject to unusually severe vibrations. A modified form of the galvanometer suspension described by Julius3 has damped the vibrations so successfully that a short note concerning it is thought to be desirable, The laboratory is on the site of the Amarillo helium plant near a building that houses gas engines of from 180 to 250 hp., driving compressors and electric generators. The distances from the galvanometers to the individual engines range from about 80 to 180 feet. The subsoil, consisting of black clay loam, transmits the impulses without much damping. The usual methods of protecting galvanometers from vibration were tried and proved fruitless. A Julius suspension purchased on the market was carefully installed in the hope that it would overcome the difficulty, but the conditions were too severe even for this elaborate arrangement. Several mudifications of the original Julius suspension, which were then introduced, resulted in almost complete elimination of all vibrational effects.

Jan 1, 1931

By Sidney Katell

Tonnage oxygen plants are or can be made available in sizes ranging from 150 to 1,000 tons per day. Capital requirements are estimated from $5,400 to $14,700 per daily ton, depending upon size of plant, cycle employed, and purity and discharge pressure of the product. Similarly, operating costs before return on investment will range from $4.80 to $10 per ton. INTRODUCTION Several processes4 5/ that can be used to convert coal to synthetic liquid fuels, synthetic pipeline gas, or hydrogen require high-purity oxygen as one of the basic raw materials. Depending on the and product and its specific use, the oxygen required will be of 95 or 99.5 percent purity. The quantity required, in turn, depends on the process for which the oxygen will be used and the size of the processing plant and will range from 150 to 4,000 tons per day.

Jan 1, 1960

By S. P. Sandoval

The U.S. Bureau of Mines investigated the separation of aluminum from copper dump leaching liquors using a supported liquid membrane. Aluminum was selectively transported through porous polypropylene impregnated with di (2-ethylhexyl) phosphoric acid in an aliphatic diluent. The effects of variables, such as solution composition, temperature, and extractant concentration, were measured with a three-level fractional factorial experimental design. Experimental results were used to derive equations for predicting transport rates for aluminum, iron, and copper. The major variables influencing aluminum transport were solution temperature, feed solution pH, aluminum concentration in the feed solution, and extractant concentration. Copper and iron transport rates were almost zero when aluminum transport rates were high. Measured aluminum transport rates under the best conditions of 55° C, pH 3.0, 16 g/L A13+, and 65 pct extractant solution confIrmed the predicted value of 210 f.'g/(cm2.h). Transport rates for iron and copper were less than 5 ug/(cm2.h) under these conditions. Aluminum was recovered from the stripping solutions by sparging with gaseous hydrogen chloride to crystallize aluminum chloride hexahydrate, which was calcined to alumina. Sparging crystallization regenerated the stripping acid for recycle.

Jan 1, 1989

By Alden H. Emery, J. J. Forbes

"IntroductionThe data contained in this paper were collected during the course of an investigation which covered 15 representative coal mines in 6 coal-mining States. The purpose of the investigation was to determine by atmospheric sampling how much dust was raised into the air during the various operations of coal mining, such as undercutting with machines, loading coal by hand, and transporting it from the working face to the surface. The data thus obtained were considered from two angles - namely, the possible physiological effect of inhalation and the explosion hazard of the dust. No attempt will be mode to discuss the former factor in this paper.CONDITIONS OF MININGThe mines in which this investigation was conducted were considered representative, and it is believed that the results obtained will suffice for the average dustiness encountered in most coal mines. .All of the coal mined was bituminous, from beds 30 to 120 inches thick. Only the ordinary room-and-pillar system of mining was employed. Daily production ranged from approximately 700 to 1500 tons and the men employed from 150 to 450. Coal was undercut by short-wall mining machines in all mines, with the exception of one in which pick mining was employed. Loading at the face was done by miners; none of the mines used mechanical loaders. Electric drills, both for brushing roof and for shooting coal, were commonly used although some roof work was done with jack-hammers and a. little of both with augers. Coal was hauled by motor, mule, or rope power in end-gate cars with capacities ranging from 1600 to 3600 pounds. With few exceptions, coal was won at the face by dry methods - that is to say, no water was employed fox wetting down the dust either during undercutting, loading, or transportation."

Feb 1, 1927

By C. E. Augustine, B. A. Landry, P. Nicholls

"Wien bituminous coal is burned in a hand-fired up-draft boiler used for heating purposes it has a decided tendency to produce smoke. A design of furnace and a method of firing and attendance that are satisfactory for fuels low in volatile matter, as anthracite or coke, are not necessarily Satisfactory for bituminous coals. It is therefore becoming common practice to use a special design of furnace for bituminous coals, in order to facilitate the combustion of the volatile matter and soot. This is done by (1) providing a larger combustion space to give more time for the combustion, (2) construction that will produce a better mixing of the gases and secondary air supplied over the fuel bed, or (3) keeping the gases at a higher temperature by preheating the secondary air, as may be done by surrounding them with refractory surfaces, or causing them to pass through a fuel bed of hot coke. A furnace may be built to use any or all of these methods of smoke prevention.In Bureau of Mines Technical Paper 303, Blizard5 and others give tests on a large heating boiler when burning coke, anthracite, and bituminous coal. Certair alternative furnace arrangements were used, but there was no material change in the furnace design for the various fuels. Since that time the manufacturer has made modifications in design to adapt it for use of bituminous coal, and additional tests have been made to determine how this change affected the production of smoke and the efficiency of the boiler."

Jun 1, 1929

By Charles H. Parr

A testing program was conducted to determine the suitability and reliability of adhesives and polycarbonate lenses for extended use in luminaires in mine environments. Polycarbonates were exposed, for periods up to 36 months, to four environments including ultraviolet light, humidity, intermittent water spray, and heat of either 180°F or 407 in various combinations. Rod impact tests on the exposed lens material indicated, that polycarbonate functions well under all 180°F environments and could be used with confidence for periods exceeding the test period, for as long as ten years, with a suit) able safety factor employed in design. The specimens exposed at 240°F showed decreased toughness after 24 months' exposure. Extrapolation of these data was deemed to be risky. A 462-day compatibility test between polycarbonate and six hydraulic fluids was run on stressed PC beams. One fluid caused beam breakage in less than one day, while three caused breakage at intermediate times. Two fluids exhibited essentially no effect on the PC when compared to a control. Epoxy and silicone adhesives were tested as lens adhesives and sealants. Three epoxy combinations tested showed low and erratic failure stresses. A room-temperature-cure silicone adhesive functioned extremely well for time periods up to 36 months and temperatures u2 to 240°F.

Jan 1, 1985

By H. D. Jacobs

The Federal Bureau of Mines, as part of a program to insure future raw material needs for the iron and steel industry, undertook research to beneficiate the oxidized taconites from the western Mesabi range in Minnesota. The data presented were obtained by applying the Bureau-developed selective-flocculation/cationic-flotation process to the second of three oxidized taconite samples. These three samples are representative of an estimated 10 billion tons of ore analyzing 30 to 40 pct iron. The experimental work was performed in a 900-lb/hr pilot plant. Treating the ore sample (36.1 pct Fe) with the Bureau's process produced commercially acceptable concentrates averaging 63.5 pct Fe and 4.3 pct SiO2, with an average iron recovery of 84.6 pct.

Jan 1, 1980

By Robert M. Koerner

The feasibility of using small-scale models to simulate residential masonry foundation walls subject to fatigue loading was investigated. Five wall segments were modeled in one-quarter scale using dynamic similitude equations. The walls were dynamically loaded using a sinusoidal base motion and wall accelerations were monitored. The stiffness, natural frequency response, and damping characteristics were measured. The number of cycles of testing necessary to cause initial visible cracking was recorded. Analysis of the data indicated the importance of the relationship between the forcing function and the natural frequencies of the structure in influencing cracking damage.

Jan 1, 1980

By G. R. Hopkins

[A new record in fuel efficiency at petroleum refineries was established in 1939, when a the average e B.t.u. requirements per barrel of crude oil processed declined to a new low of 557,000 B.t.u. (see fig, 1).]

Jan 1, 1941

By W. J. McKenna

This paper, describing the milling practice at tine lead-zinc concentrator of the International Smelting Co., is one of a series of papers on milling methods being prepared by the United States Bureau of nines. The concentrator is operated as a unit of the International Smelting Co. and is located about 40 miles southwest of Salt Lake City, at Tooele, Utah. The Tooele Valley Railroad, operating between the plant and Warner, Utah, a distance of 6.5 miles, makes connection with both the Union Pacific and Denver & Rio Grande Railroads.

Jan 1, 1933

By G. R. Hopkins

[A new record in fuel efficiency at petroleum refineries was established in 1939, when a the average B.t.u. requirements per barrel of crude oil processed declined to a new low of 557,000 B.t.u. (see fig. 1). The average fuel requirement per barrel of crude oil refined has remained virtually stationary for the past 3 years. Thus in 1937 the average was 562,000 B.t.u., in is it rose to 567,000 B.t.u., and in 1939 it declined to 557,000 B.t.u. she largest gains in fuel economy cane a decade or so ago on the widespread introduction of heat exchanges and pipe stills. In recent years many successful innovations in heat saving have been adopted, but the combined effect of those is completely masked by the degree to which the capacity is utilized. Some heat requirements are relatively inelastic, so the average consumption per barrel of crude oil refined tends s to increase when the operating ratio (crude runs divided by capacity) declines and vice versa. In 1939 crude runs to stills increased 6 percent (from 1,165,015,000 barrels in 1938 to 1,237,840,000 in 1939) compared with a decline of about 2 percent in 1938. The operating ratio in 1939 was 82 percent compared it's 78 percent in 1938.]

Jan 1, 1941

By Cheryl Hill, Michael Keane, Pamela Mike, Raghoottma Pandurangi, William Wallace, Mohindar Seebra, Val Vallyathan

"Dipalmitoyl glycerophosphorylcholine (lecithin) dispersed in physiologic saline, a model of the primary component of pulmonary surfactant, is adsorbed by respirable quartz and aluminosilicate dusts. Dust cytotoxicity as measured by erythrocyte bemolysis and pulmonary macrophage enzyme release is suppressed by this adsorption. The degree of suppression of hemolytic potential versus specific adsorption of lecithin from dispersion in saline by respirable quartz and kaolin dusts are compared with dusts' BET specific surface areas to interpret the prophylactic effect of lecithin adsorption. Dust hemolytic potential versus medium pH is presented. Fourier transform infrared spectroscopy and photo-acoustic spectroscopy of lecithin on quartz and of lecithin on kaolin are presented and reviewed with results of studies of the time course of removal of lecithin adsorbed on mineral surfaces by digestion by phospholipase enzyme. Results are discussed in terms of a model of prompt neutralization of respired mineral dusts by pulmonary surfactant, and a gradual re-toxification by digestive processes acting on the adsorbed prophylactic surfactant coating following phagocytosis. INTRODUCTIONQuartz dust of respirable size is well known to cause fibrotic lung disease, but numerous questions persist in the understanding of the initiation and progression of this disease. Our approach concentrates on physical and chemical aspects of mineral dusts early-on in their interactions with living organisms, and we have chosen simplified models to investigate that interaction.In the alveolar ·spaces of the lung, tissue is coated with a surface-active material (pulmonary surfactant), which, among other functions, mechanically stabilizes the lung from collapse by reducing the surface tension of water in the alveolar sacs.1 This surfactant is also the material that is first contacted by a mineral particle that is transported to an alveolus and is impacted there. This surfactant material has been studied extensively. The primary components are known to be proteins (about 11 % in dog lavage fluid), and phospholipids (about 88%).2 Pbosphatidyl cholines constitute roughly 80% of the phospholipid fraction; about 70% of the phosphatidyl choline fraction is dipalmitoyl lecithin (DPL).2 Respirable aluminosilicate particles are capable of adsorbing dipalmitoyl lecithin from dispersion in physiologic saline, a model for a possible initial event occurring upon deposition of a particle in a pulmonary alveolus. As may be seen from Figure 1, the DPL molecule has several fixed charges at neutral pH; a positive charge on the trimethylamine (choline) moiety, and a negative charge on the phosphate group. Also evident are the two fatty acid residues of palmitic acid, which are bonded through ester likages to the glycerol segment of the molecule. The fatty acid moieties of phosphatidyl choline make the molecule inso1uble in aqueous solutions under normal conditions, but a colloidal unit of aggregated molecules called a micelle is usually formed spontaneously above a certain minimum concentration. Small micellar vesicles are generally formed in the laboratory by using ultrasonic agitation or by solvent evaporation methods."

Jan 1, 1990

By W. W. Agey

As a result of a field examination made during the Bureau of Mines intensive manganese program, three lots of ore were procured from the famous old Paymaster District, 7 miles from Midway Wells, Imperial County, Calif. This district is an old producer and shipped approximately 10,000 tons of 45-percent manganese ore during World War I. A 2-ton lot of ore was taken of a Bureau engineer from the exposure of a small fissure vein in conglomerate on the Turtle Group of claims; 1 mile east of the Pacific Coast Manganese Corp. claims. The vein material consisted of manganese oxides, calcite, and quartz in fairly coarse association.

Jan 1, 1949

By L. E. Schultze

Experiments were conducted by the U.S. Bureau of Mines to verify enhancements due to chloride and surfactant additions in the leaching system of chalcopyrite with ferric sulfate and sulfuric acid. A statistical experimental design was used and equipment was designed to eliminate contributions from changes in solution electrochemical potential during the course of the measurements. Results confirmed that chloride additions increased chalcopyrite leaching by as much as 94 pct over the electrochemical potential versus hydrogen electrode range of 630 to 750 mV at pH 1.7 and 50°C. Total iron concentration had no effect over the range of 1 to 5 g/L. The effect of surfactant addition was less well defined. While additions of LA 790 (a polyoxyethylene lauryl ether) resulted in increased copper leaching in several of the tests, the differences were too small to be statistically significant. No interaction effect could be verified.

Jan 1, 2010

By R. H. Grau, A. Sainato, S. J. Schatzel, T. M. Kohler, A. T. Iannacchione

This Bureau of Mines research study found gas emission rates from an advancing face, and flows and pressure of gas from an exploration drill hole were dependent upon the geology of salt encountered in a domal salt mine. Normal production-grade "pure" salt adjacent to an anomalous' zone was found to have a methane emission rate of less than 5 ft3/ ton (0.1 m3/t) of mined salt from a room advanced by a continuous miner. Extremely low gas flows [less the 4 ft3/h (0.1 m3/h)] and lack of pressure buildup were also observed from this normal salt in a 154-ft (47-m) exploration drill hole. These data indicate that methane emissions should not be a problem when mining in this type of salt. In the adjacent anomalous zone, methane emission rates ranged from 15 to 70 ft3/ton (0.4 to 1.8 m3/t) of mined salt from an advancing face. Gas flows of approximately 42 ft3/h (1.2 m3/h), and pressures in excess of 900 psig (6,200 kPa) were observed in an exploration drill hole when the anomalous zone was encountered. This information suggests a greater methane emission hazard from the anomalous zone than from the associated normal salt. If this trend of increasing emissions problems associated with anomalous zones of salt is common with similar anomalous zones encountered or observed in other domal salt mines, then special control strategies should be employed to minimize this potential mining hazard.

Jan 1, 1984

By B. P. Martinez

In response to a request from the President, the Department of the Interior joined with other agencies in a comprehensive study of the land and water resources of the New England-New York region. As part of this study, chemical engineers of the Bureau of Mines have visited 1,025 mineral-industries plants to inventory the waterborne wastes of mineral origin, discharged by the mineral industries of the New England-New York region. Four-hundred and sixty-two of these plants disposed their wastes to a public sewer of some type, but waste control remains a problem for moat of them. The 1,025 plants are discussed in main industry groups according to their production: Chemical and allied products. Stone, clay, and glass products. Iron and steel and their products (except machinery). Nonferrous metals and their products. Electrical machinery. Machinery (except electrical). Transportation equipment. Miscellaneous mineral industries.

Jan 1, 1956