Search Documents

By Keith A. Heasley, John L. Ellenberger

The National Institute for Occupational Safety and Health (NIOSH) has continued the research role of the former U. S. Bureau of Mines to develop techniques that will reduce the hazards in the mining work place associated with coal bumps. Current research focuses on both analyzing historical seismic data from bump-prone operations and utilizing a mine-wide seismic network to investigate the exact strata failure mechanics associated with bump-prone geology. The anticipated outcome of this research will be reduced bump incidences through advanced engineering concepts and designs which implement the new understanding of strata behavior. The analysis of the historic seismic data consists of correlating observed mining seismicity with the geologic and geometric parameters at the sites. The primary seismic parameters are the timing, location and magnitude of are corded seismic event. These parameters are correlated with such mining parameters as: the overburden, the size of the immediate gob, the size of the district gob area, etc. This detailed analysis of historical seismic data has provided an informative quantifiable relationship between many of the specific mining parameters and the induced seismicity. The second aspect of the coal bump research is the instrumentation of an appropriate field site to determine the main roof, floor, and gob behavior associated with bump behavior. The chosen field site is a deep-cover longwall mine with competent geology in a historically bump-prone area. The primary field instrumentation is a three-dimensional, full-waveform, seismic array with both surface and underground sensors surrounding an active multi-panel district. The purpose of this seismic array is to determine the timing, the exact location, and the mechanism (tensile fracture, bedding plane slip, etc.) of the failure of the strata surrounding the active and multi-panel gobs. The preliminary results presented in this paper help to define the strata failure areas around the longwall panel.

By G. A. Morrison

Iron ores associated with the Oriskany formation extend from the West Virginia border to the southwestern corner of Virginia. The deposits have been mined at many places, and the district is credited with the production of approximately 13,000,000 tons of ore to 1925, when mining operations ceased (fig. 1). The Oriskany iron-ore deposits occur in the Alleghany Mountains throughout their extent in the State. The name Oriskany was originally given to the limonite ore that was supposed to occur in the Oriskany sand-stone. At present, the name applies to all iron-ore deposits occurring in the lower part of the Devonian shale, Oriskany sandstone, and Helderberg limestone. The principal ore-bearing minerals are goethite and limonite. This report deals principally with the occurrences in Allegheny, Bath, Botetourt, and Craig Counties, Va. The Bureau of Mines, as part of the strategic-minerals program, began a project to develop the reserves of the area in November 1943; and continued until December 1944. Work started near Oriskany and extended northeast for nearly three-fourths of the area of the more important deposits. During the program 163 holes were drilled, totaling 11,651 feet; 256 feet of prospect tunnels were driven; 1,346 samples were collected; beneficiation tests were performed; and bulldozer trails and trenches wore excavated. The work served to delimit and appreciably extend the reserves of several areas. Analyses of channel samples are -given in appendix A, and diamond-drill and churn-drill hole logs and sample analyses are given in appendixes B and C, respectively.

Jan 1, 1950

By A. B. Campbell

The mines in the eastern part of the now active region of the Tri-State zinc district of Missouri, Kansas, and Oklahoma have unusually acid water, which during periods of moderate or no rainfall As used in the mills to replace losses from evaporation, seepage, and tailings disposal. Its use has caused difficulties by corrosion of equipment and by interference with flotation. The growing importance of flotation- Which requires good water, and the increasing troubles caused by the corrosion of the milling equipment have prompted the Mississippi Valley Experiment Station of the United States Bureau of Mines, in cooperation with the Missouri School of Mines and Metallurgy, Rolla, Mo., to investigate the action of the waters on flotation and to undertake to develop means of obviating their harmful effects.

Jan 1, 1932

By G. W. Center

This manual is intended to assist federal, state, and local regulatory and planning agencies, the mining industry and consulting engineers in determining the regulatory, environmental, technical and economic constraints influencing the site selection, planning, construction/operation and reclamation phases of a waste disposal facility. The information presented illustrates that factors affecting an individual site may be simple or very complex. This manual discusses methods for making future land use decisions, determining regulatory requirements, evaluating physical, chemical and structural properties of the disposed waste and selecting appropriate waste disposal methods and control techniques. Procedures and guides in the manual will assist personnel in assessing the complexities of waste disposal on a site specific basis. The major types of waste disposal systems are discussed and evaluated in terms of their advantages and disadvantages and applicability to varying site conditions and waste characteristics. Appropriate references following each chapter provide more detailed data on material presented in the text.

Jan 1, 1982

By Gregory M. Molinda

Coalbed discontinuities historically have been hazardous to mining as well as obstructions to efficient production. An effective means of mapping these features is needed in order to plan safe and efficient mine development. This Bureau of Mines report discusses the use of surface seismic techniques for this purpose. At a southwestern Pennsylvania mine, a system of coalbed discontinu-ities (paleochannels) was accurately mapped by the Bureau of Mines using borehole log methods and underground observation. This site was chosen to test the value of a high-resolution surface seismic reflection on technique for coalbed mapping. A statistical study performed at this mine indicated that the probability of accurately delineating this paleochannel system with conventional borehole methods was remote. A total of 1.47 miles of high-resolution seismic survey, comprised of four seismic profiles, was conducted in known and suspected coalbed discontinuity areas. Several test holes were drilled on the seismic lines in order to evaluate the interpretations. It was found, based on these and other existing boreholes, that it is possible to predict these dis-continuities. Paleochannel washouts were correctly predicted in several instances but in other instances were either incorrectly predicted or not predicted in areas of known discontinuities.

Jan 1, 1988

By M. Carrales

This Bureau of Mines report presents information on the sulfur content of crude oil in the United States and in some foreign countries. Data are presented for oil produced in 1971 from fields in 26 States that accounted for about 76 percent of total U.S. oil production; the foreign data cover fields in 24 foreign countries that accounted for about 64 percent of the total oil produced from these countries in 1971. Most of the data are presented in tabular form.

Jan 1, 1975

By Jr. Boyle

This report analyzes the availability of chromium in the form of ferroalloy products (high-carbon and low-carbon ferrochromium and ferrochromium-silicon) and chromite products (metallurgical, chemical, refractory, and foundry sands) in market economy countries (MEC's). A total of 873.5 Mmt of in situ material, containing 202.5 Mmt of chromium, in 10 MEC countries was analyzed for availability as of the January 1989 study date. Extraction and beneficiation of this in situ material would result in 475.4 Mmt of marketable chromite products. As analyzed, 288.5 Mmt of these chromite products would be available for export or for internal chemical and refractory use and 186.9 Mmt would be smelted in-country to produce 74.3 Mmt of high-carbon ferrochromium, 3.9 Mmt of low-carbon ferrochromium, and 2.0 Mmt of ferrochromium-silicon, all available for export. A network flow model, which includes centrally planned economy countries (CPEC's), was also constructed to analyze world chromium supply and demand interactions for the period 1986 through 1994 and to address a hypothetical North American embargo on direct imports of all South African chromium products beginning in mid-1990. The model shows capacity constraints developing in the MEC high-carbon ferro chromium industry in 1987 and a possible subsequent overreaction by the industry in terms of new capacity additions. The results suggest that sufficient chromium is available to North America should an embargo on direct imports from South Africa be imposed by its governments. However, the effect on export revenues in South Africa is relatively small, and timely increases to world ferrochromium, chemical chromite, and foundry sand chromite capacities would be required.

Jan 1, 1993

By E. A. Mevissen

With the ever increasing consumption of mineral commodities, the vital question is not whether sufficient mineral quantities will be available, but rather can the known existing low grade resources be mined economically. Conventional conveyor systems are being used in some open pit mines to decrease haulage costs. n an effort, to take this concept one stop further, this contract study examines the use of a high angle conveying system in an open pit mine. It identifies available high angle conveying equipment and examines the haulage and crushing costs associated with both a conventional truck and shovel mining operation and a high angle conveyor operation. These costs analyses were performed on a hypothetical copper, taconite and phosphate mine. Information was gathered from a series of high angle conveying equipment and open pit mining operations in the U.S. Volume I includes a detailed review of the state-of-the-art in high angle conveying concepts, the, hypothetical mine development, and the cost analyses. Volume II includes the appendices.

Jan 1, 1981

By Jack Mantel

The goal of this 42-month contract was to increase safety in low-seam underground coal mines through development and in-mine evaluation of a temporary roof support system for roof drills and floor-riding operator compartments for a loader and shuttle car. The program was performed in three phases. During Phase I, state-of-the-art canopy technology was investigated, and preliminary design and mock-up evaluations were performed for temporary roof supports for single-and dual-boom bolters and for transverse-mounted floor-riding canopies for a shuttle car and coal loading machine. The shuttle car and loader canopies were approved for further development, and the design, fabrication, testing, and certification were completed in Phase II. In Phase III, the Bureau of Mines furnished an FMC 6L shuttle car fur use in the evaluation of the canopy for 45 shifts. The shuttle car canopy was evaluated at Virginia Crews Coal Company in West Virginia. Efforts to secure an evaluation site for the loader canopy were unsuccessful. The loader canopy was shipped to Bruceton for possible future evaluation.

Jan 1, 1985

By Edmund S. Leaver

The selection of a process for treating a gold ore is governed primarily by the characteristics of the ore under consideration. The form in which the gold occurs, its mode of association with other minerals, and the size and surface condition of the gold particles are important factors which influence materially the choice of procedure for recovering gold. A knowledge of these characteristics may be obtained by microscopic and chemical methods combined with experimental testing. Cyanidation and amalgamation, either alone or in conjunction with flotation and gravity methods, are peculiarly adapted to the treatment of gold ores, especially those of relatively low grade. Gold alloys readily with mercury provided both present clean surfaces. The presence of oils and grease, antimony and arsenic minerals, or soluble sulphides have a harmful effect. Very small, flaky particles of gold frequently are lost in amalgamation because of noncontact with the mercury. Fine gold in pyrite, or gold having rusty or contaminated surfaces, is often lost for the same reason. Grinding or some form of abrasion sometimes removes surface films of iron oxide or substances of a similar nature, and alkalies or other chemicals are used to remove grease. Gold is readily soluble in cyanide solution, and this method of treatment is particularly effective in the recovery of gold from the tailings resulting from other types of concen¬tration procedure. Cyanide solutions must contact the gold to insure recovery, and the porosity of the ore treated and the fineness of grinding required are important governing factors. The use of lime in cyanidation is necessary to protect the cyanide, to precipitate undesirable substances, and to settle slimes. Certain substances in ores are harmful in cyanidation; chief among them are those that combine with cyanide, forming cyanides, and carbon which precipitates gold from solution. Arsenic and antimony are also harmful if present in sufficient quantity. These and other difficulties encountered in cyaniding certain ores often are overcome by roasting prior to leaching. Zinc dust is used almost universally for precipitating precious metals from cyanide solutions. The refining and melting of the product may be accomplished by oxidizing the zinc before melting it in graphite pots with fluxes, although sulphuric acid is now used largely to remove the zinc before melting. Straight cyanidaticn practice is being replaced by flotation as a major process, followed by cyanide leaching of the tailings, but amalgamation is still needed as a primary process for the recovery of coarse gold before either flotation or cyanidation.

Jan 1, 1935

By Edmund S. Leaver

The selection of a process for treating a gold ore is governed primarily by the characteristics of the ore under consideration. The form in which the gold occurs, its mode of association with other minerals, and the size and surface condition of the gold particles are important factors which influence materially the choice of procedure for recovering gold. A knowledge of these characteristics may be obtained by microscopic and chemical methods combined with experimental testing. Cyanidation and amalgamation, either alone or in conjunction with flotation and gravity methods, are peculiarly adapted to the treatment of gold ores, especially those of relatively low grade. Gold alloys readily with mercury provided both present clean surfaces. The presence of oils and grease, antimony and arsenic minerals, or soluble sulphides have a harmful effect. Very small, flaky particles of gold frequently are lost in amalgamation because of noncontact with the mercury. Fine gold in pyrite, or gold having rusty or contaminated surfaces, is often lost for the same reason. Grinding or some form of abrasion sometimes removes surface films of iron oxide or substances of a similar nature, and alkalies or other chemicals are used to remove grease. Gold is readily soluble in cyanide solution, and this method of treatment is particularly effective in the recovery of gold from the tailings resulting from other types of concentration procedure. Cyanide solutions must contact the gold to insure recovery, and the porosity of the ore treated and the fineness of grinding required are important governing factors. The use of lime in cyanidation is necessary to protect the cyanide, to precipitate undesirable substances, and to settle slimes. Certain substances in ores are harmful in cyanidation; chief among them are those that combine with cyanide, forming cyanides, and carbon which precipitates gold from solution. Arsenic and antimony are also harmful if present in sufficient quantity. These and other difficulties encountered in cyaniding certain ores often are overcome by roasting prior to leaching. Zinc dust is used almost universally for precipitating precious metals from cyanide solutions. The refining and melting of the product may be accomplished by oxidizing the zinc before melting it in graphite pots with fluxes, although sulphuric acid is now used largely to remove the zinc before melting. Straight cyanidation practice is being replaced by flotation as a major process, followed by cyanide leaching of the tailings, but amalgamation is still needed as a primary process for the recovery of coarse gold before either flotation or cyanidation.

Jan 1, 1935

By George S. Rice

The prevention of coal-mine explosions has been one of the chief purposes of the Bureau of Mines. In facti the first Federal appropriation relating to mining methods, in 1908, authorized the investigation of the causes of mine explosions and the possible methods of preventing them. When that investigation started the mining industry had not determined the real causes of a succession of terrible coal-mine explosions in various countries, culminating in the great disasters at CoulTièl'es, France, and Monongah, W. Va. Coal dust as an agent of widespread explosions had been under suspicion, and watering to allay the dust was recommended by some mining engineers but the watering of coal-mine dust was adopted in comparatively few mines of the United States and Great Britain, and had not been introduced widely in any country except Germany. Rock dusting, another method of preventing explosions of coal dust, was early tested with success by the Bureau of Mines in its fist gallery at Pittsburgh and, beginnig in 1911, at the experimental mine, Bruceton, Pa. Several of the fist publications i of the bureau suggested that rock dust be used in gaseous or dusty bituminous mines, and in 1915 Technical Paper 842 strongly recommended it. Since that time additional tests in the experimental mine have fully confied this :ft judgment.

Jan 1, 1924

By W. M. Bangert, F. S. Boericke

"INTRODUCTION Previous investigations of the Boulder City station of the Bureau of Mines have demonstrated that low-grade domestic chromite concentrates can be roasted with carbon to obtain selective reduction of the contained iron, and that the reduced iron can be removed by acid leaching of the roasted products to produce residues with higher chromium iron ratios. Thus, some chromite ores or concentrates that originally contain too much iron to be acceptable for the production of ferrochrome can, by this treatment, be rendered marketable as ""high-grade"" chromite. 3/The present report supplements the earlier work of the Bureau and re¬cords the results of small-scale laboratory tests investigating the effects of:1. Temperature and time of the reducing roast.2. Chromite and carbon particle size.3. Ratio of carbon to chromite in the initial roast mixture.4. Variations in the alumina and silica content of the ore.5. Back-oxidation of the roast product.6. Temperature and time of leaching .of roast product.This work differs from that done previously in that particular emphasis was placed on roast mixtures containing just enough carbon for the reduction of the iron in the chromite, whereas some two and one-half times this amount of carbon was used in the earlier work.In addition to these tests, the mechanism of the production reactions was examined for the purpose of explaining the precance of acid-soluble chromium, which occurs under certain conditions of chromite reduction."

Jul 1, 1945

By David Montgomery

The feasibility of building a calibrator for the DuPont D-100 audio dosimeter is discussed. The desired specifications are used as guidelines but the possibility of their relaxation is also considered. Commercially available equipment is surveyed and found to not satisfy the guidelines. Several alternate concepts are investigated, and recommendations for further work are presented.

Jan 1, 1974

By Richard V. Ageton, Harry E. Tufft, E. A. Holbrook

When an underground excavation is made, the rock surrounding the sides and top of the opening is deprived of its natural support and tends to fall. Whenever caving takes place, the time and extent of the caving depend on the character and condition of the rock. In strong homogenous rock, such as solid granite, even a large chamber may stand indefinitely, whereas a soft material, such as clay or a loose material like unconsolidated sand, falls immediately if not supported. Weaknesses in the rocks induced by structural features, such as joints, :fissures, bedding and cleavage planes, and fractures produced by blasting, will cause the falling of insecure blocks or slabs unless means are provided to support these in place. In an unsupported mine opening, as a tunnel, the first slight settling or adjusting movement of the rocks (the "initial creep" or "set") is caused by the great weight of overlying material pressing down the rock masses above and around the roof and sides of the opening until they key together in roughly the form of an arch. The rock, after it has adjusted itself to this shape, becomes. selfsupporting. Timbering is necessa.ry in all mining only to support, therefore, those comparatively small blocks or pieces of rock which tend to loosen from the top and sides of the opening during or after the formation 'of the natural rock arch, and which lie between this natural rock arch and the opening. This statement, of course, has its limitations. For example; a layer of strong rock, like limestone, may act as a beam; then only the material under the limestone will need support. Timbering is not, as is commonly supposed by the layman, used to supp!ort the huge mass of rock between the back (roof) of an underground opening and the surface. It would be impossible to place enough timbers in a:ny underground opening to support such a mass. This fact is not'·perceived by all miners.

Jan 1, 1923

By John R. Troxell

"INTRODUCTION The Ahles iron mine, also known as the Pequest mine, in Warren County, N. J., was operated continuously for 15 years and was still in ore when it closed in 1916.Tie property was examined by an engineer of the Bureau of Mines in March 1943. 3/ This examination led to an investigation of the deposits by the Bureau by diamond drilling two holes under the old workings to determine whether the extends downward.This report describes the work done at the Ahles mine by the Bureau and presents the data obtained.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. The Mining Division, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual investigative work, and prepares the final report.The Metallurgical Division, O. C. Ralston, chief, analyzes samples and performs beneficiation tests.The investigation was under the general supervision of J. B. Zadra, acting regional engineer, and under the immediate supervision of G. D. Jermain, district engineer for the States of Pennsylvania, New Jersey, Maryland, and Delaware. The author was in direct charge of the project.The chemical analyses for the project were performed at the College, Park, Md., laboratories of the Bureau of Mines under the direction of M. S. Sheftel. The ore-dressing tests were conducted at College Park under the direction of Frank Lamb. Preston E. Hotz, of the Federal Geological Survey, logged and interpreted the drill cores."

Apr 1, 1948

By Gabriel S. Esterhuizen, Anthony T. Iannacchione

The roof rock in underground limestone mines in Northern Appalachia can be subject to high horizontal stresses in spite of the shallow depth of the workings. The high stresses can cause roof stability problems. The National Institute for Occupational Safety and Health staff have observed a distinctive asymmetrical mode of failure at the pillar-roof contact in two underground stone mines, which is different from the typical failure mode observed in response to excessive levels of horizontal stress. A dip of greater than 5° was identified as a possible cause of this mode of failure. Numerical model experiments showed that an increase in the dip of the workings can cause an increase in the stress at the up-dip corner of the roof beam. A case study is presented in which failure at the pillar-roof contact was observed where the dip of the workings was 7° in a high horizontal stress field. Numerical modeling showed that the relatively small dip of the workings could have induced stresses changes in the immediate roof that would explain the failures. The model results also showed that this mode of failure is less likely to occur if the limestone pillars contain weak bedding planes that provide stress relief. In addition, the results showed that for the conditions at the case study site, the stress in the roof beam was not sensitive to the thickness of the roof beam or to the excavation span. The high horizontal stresses at this site are an important contributing factor to the observed failures.

By Robert M. Doerr

Isothermal oxidation kinetics were determined for three grades of Ni and for 99.99 percent Co in Ca and in air from 800° to 1,200° C. The oxidation reactions followed approximately the parabolic rate law. For 99.99 percent Ni in 02 at 1,200° C, the parabolic rate constant was 2 mg cm-2 hr-2. For 99.99 percent Co in dry air, the constant ranged from 1 mg cm-2 hr-2 at 800° C to 18 mg cm-2 hr-2 at 1,200° C; for 99.99 percent Co in 02 the constant was 2 mg cm -2 hr-2 at 800° C and 10 mg cm-2 hr-2 at 1,000° C. For 99 percent Ni in dry air, the constant ranged from 0.2 mg cm 2 hr-2 at 800° C to 3 mg cm 2 hr-2 at 1,200° C. By X-ray diffraction measurements, only divalent oxides were found in the scales. Volumetric and quartz-helix gravimetric methods were used. The volumetric apparatus was designed to permit less stringent restrictions on the corrosion specimens; it was also more convenient to use. The agreement between the weight gain determined gravimetrically and the 02 consumption determined volumetrically was not good enough for direct comparison of gravimetric and volumetric results.

Jan 1, 1963

By James J. Snodgrass

A new technique was used to obtain detailed sonic logging data in drill holes above the water table at a coal mine site in northeastern New Mexico. The equipment was developed under contract to the Bureau of Mines and the U.S. Department of Energy to indirectly evaluate the in situ structural properties of coal and overburden. The system comprises a hydraulically operated, wall-clamping downhole probe compatible with standard four-conductor logging cable, and a surface control module. Resolution of layering is 0.6 meter (2.0 ft), and a redundancy of data from separate receivers provides accurate timing measurements. Preliminary results in the settled overburden of an excavated long-wall panel indicated a low average velocity zone, extending approximately 18 meters (60 ft) into the immediate roof of the coal seam. Subsequent measurements improved the field and recording procedures to produce high quality waveforms from which both P and S arrivals may be visually interpreted. Over a representative section of interbedded sandstone, siltstone, shale, and coal, Vp and Vs varied considerably even within lithologic units. Compressional wave velocity in the coal seam, Vp = 1,740 m/sec (5,700 ft/sec), was in the range of variability of published data.

Jan 1, 1982

By R. K. Zipf

A method is presented for creating realistic numerical models for practical coal mine ground control. The method includes procedures to collect the necessary mechanical input parameters from a geologic core log, procedures to set up a model and procedures to interpret calculation results. The input parameters come from a detailed geologic core log and extensive point load tests of estimate rock layer strength. A suite of material property input parameters is proposed which allow the user to go from core log to numerical model inputs. Rock bolt anchorage properties are also linked to the material properties of each geologic layer in the model. Following this procedure leads to very realistic calculations of the rock failure process and rock support system behavior. These calculations in turn enable realistic comparison of the effectiveness of alternative rock support systems.