Search Documents

By Robert Stefanko

A series of workshops were conducted -with invited participants from the coal mining industry to identify the most pressing research and development needs of the industry. Six workshops were held on the following subjects; Research Priorities for Mining-Oriented Universities, R&D Needs-for Surface Coal Mining, R&D Needs for Deep Coal Mining, R&D Needs for Anthracite Coal Mining, R&D Needs for Coal Mine Health and Safety, and R&D Needs far Environmental Control in Coal Mining.

Jan 1, 1975

By John E. Rourke, O&apos

This report documents the process of site selection, instrument installation, data acquisition, and preliminary data analysis followed to characterize the physical response of overlying strata to longwall mining. A system of surface, subsurface and mine level instrumentation was installed at the Allen Mine in Weston, Colorado where the overburden varied in thickness from 600 to 900 feet. Survey monuments, automatic-recording strain-meters, multi-point rod extensometers, inclinometer-extensometers, stressmeters and tape extensometer convergence stations were installed to monitor displacements and stress changes. A preliminary analysis of the data acquired up until project termination has shown the system to be operative and strata response to be similar to that reported for other subsidence monitoring case histories. Recommendations for continued monitoring of the instrumentation systems are presented.

Jan 1, 1982

By Samuel M. Bryant

The purpose of this study was to develop procedures to measure Bingham flow properties for mine tailings and to use these to predict the possible consequences of a hypothetical tailings flow failure at the Tenmile Tailings Pond at Climax, Colorado. The consequences of such a failure were found to be minimal, and the failure itself highly; unlikely. Values of Ty (Bingham yield shear strength) and np (plastic viscosity) were measured for 10 materials using results obtained from vaned coaxial viscometer tests and triaxial tests.

Jan 1, 1983

Research by the National Institute for Occupational Safety and Health (NIOSH) on multiple-seam mining has resulted in two new ground control products. Information Circular (IC) 9495 In some U.S. coalfields, particularly in central Appalachia and the West, most mines are operating above and/or beneath previously mined seams. The effects of multiple-seam interactions can include roof falls, rib spalling, and floor heave. These can seriously threaten the safety of miners and disrupt mining operations. Information Circular (IC) 9495 is a proceedings document containing a variety of papers that summarize recent knowledge about multiple-seam mining. A NIOSH study that analyzed case histories collected from 44 U.S. coal mines is described in detail. The study confirmed that overmining is much more difficult than undermining, and isolated remnant pillars cause more problems than gob-solid boundaries. The study's results were the basis for the Analysis of Multiple-Seam Stability (AMSS) software package. The proceedings also contain two papers describing the LaModel family of software. The original three-dimensional version of LaModel is essential for detailed analyses of complex multiple-seam scenarios. LaM2D implements a simplified, two-dimensional model suitable for quick approximations of the multiple-seam stresses and strains. Three papers in the proceedings focus on case histories. One describes the extensive multiple-seam experience at the Harris No. 1 Mine in West Virginia, a second contains examples of "extreme" multiple-seam mining from the central Appalachian coalfields, and a third describes interactions with regard to longwall mine experiences in Pennsylvania, West Virginia, and Utah. The final paper reports on a numerical modeling study that provided some insight into the mechanics of multiple-seam mining. [ ] AMSS Software Package NIOSH has developed a simple, user-friendly computer program called Analysis of Multiple-Seam Stability (AMSS). AMSS can help mine planners to evaluate each potential multiple-seam interaction and take steps to reduce the risk of ground control failure. AMSS begins by evaluating the pillar design. It first calculates the single-seam pillar stability factor (SF)

Jan 11, 2007

By Michael L. Clar

This volume is an annotated bibliography of published literature pertaining to the occurrence and control of surface and groundwater in underground coal mines. This literature was used to develop Volume 1 of this report, which assesses the feasibility of water diversion and overburden dewatering for underground coal mines in the Appalachian Region. Each abstract is followed by subject descriptors. the abstracts are listed alphabetically by title and are numbered consecutively. These numbers are used in the subject index to help the reader locate the appropriate articles.

Jan 1, 1981

By R. A. Franks, G. F. Friel, J. C. Edwards, L. Yuan

Two mine-fire experiments were conducted in the National Institute for Occupational Safety and Health's (NIOSH) Safety Research Coal Mine (SRCM) at the Pittsburgh Research Laboratory (PRL) which demonstrated that smoke from diesel-fuel fires of 500 kW and 660 kW heat-release rates in a return airway can develop, without causing a complete air flow reversal, into a roof layer that can migrate upwind forming a counter flow to the primary airflow in a crosscut. Subsequently, smoke can penetrate into an intake airway and create a hazardous atmosphere in the intake airway upwind from the fire. Visibility conditions less than 13 m were created by the smoke in the intake airway downwind from the crosscut. Modeling of the event with a three-dimensional, time-dependent, computational fluid dynamics (CFD) program correctly represented the smoke movement.

By A. Brown

This report details work performed and results obtained in a study of the water management aspects of oil shale mining and retorting in the Piceance Creek Basin. Three specific sites were investigated, and optimal water management systems for both conventional and in-situ extraction processes were generated. Water-related legal and environmental constraints on development were identified and the water management schemes were developed in compliance with these regulations. Limitations on shale oil production implied by limited water supplies were evaluated. Potential Basin-wide effects of development were evaluated using a computer model, and mitigation strategies were developed. Recommendations for additional investigation and analyses were presented.

Jan 1, 1977

By K. A. Johnson, H. F. Yancey

"INTRODUCTION Coals vary so widely in their burning characteristics that all coals prepared for domestic stoker use cannot be burned efficiently on every type of stoker. The overfeed stoker, a large number of which are in use in the Pacific Northwest, operates satisfactorily when burning low- to high-ash, noncaking bituminous or subbituminous coals, whereas on the clinkering-type, underfeed, bituminous stoker both caking and noncaking bituminous and subbituminous coals are burned, generally with ash contents below 12 percent and ash-softening temperatures between 1,800º and about 2,600º F. Because fly ash continues to be one of the most troublesome factors in domestic underfeed stokers, noncaking coals especially must be chosen carefully with respect to size composition, particularly as regards the exclusion of excessive fines. Their formation as a result of degradation in storage handling or because of crushing in .the stoker worm will increase the fly-ash nuisence.Bituminous and subbituminous coals with higher ash-softening temperatures and, often, higher ash contents have not been able to enter the domestic stoker-coal market in the Pacific northwest because clinkers are not formed readily during clinker-type underfeed-stoker burning, especially in mild weather, and because of the labor and attendant inconvenience required in handling larger volumes of ash. The work described in this report was undertaken to enable mines producing coals of the kind described to enter the stoker-coal markets. The anthracite stoker selected was one that conveys the refuse from the ash pit of the furnace and deposits it into one of two covered, dust-tight disposal cans."

Dec 1, 1945

By William O. Vanderburg

This paper describing the mining practices at the Argonaut mine, Amador County, California, is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. The mining practices described are those used in exploiting the low-grade gold ores in the heavy and swelling ground that occurs on the Mother Lode belt. The author acknowledges the assistance of E. A. Stent, vice-president, James L. Fontenrose, cost clerk, Joseph Mohorovich, mine foreman, of the Argonaut mine, and of E. D. Gardner, supervising engineer, United States Bureau of Mines, Southwest Experiment Station, Tucson, Ariz.

Jan 1, 1930

By Joseph D. Davis

The term "fusain" was first adopted from the French by the American geologist J. J. Stevenson in 1911, according to Wheeler, (1),3 who applies it to that portion of coal resembling charcoal, which he treats as one of the four ingredients of banded bituminous coal. The term has since been adopted by American writers. The Germans use it with slightly different spelling - namely, fusit. It is the equivalent of "mother-of-coal" and "mineral charcoal" of the earlier British writers. The English word fusain is also applied to "a crayon of fine charcoal" and is derived from the Latin root fusus. OCCURRENCE OF FUSAIN IN COAL AND ITS RECOGNITION Fusain is fairly widely distributed in coals of all ranks in varying amounts. It is almost always present in very thin sheets between the bedding planes of the banded coal constituents and presents a jet-black silky appearance who n the coal is split away. As fusain has little cohesive power the coal splits readily along the planes where it occurs. Such fusain bands often attain appreciable thickness -- frequently 1/4 to 3/4 inch. -Beet (2) has reported a maximum thickness of 2 inches for fusain partings, and Sinnatt (3) has found it in the form of plates and lumps; one lump taken by him from the Peacock mine weighed 3-3/4 pounds. Bore (4) has found it in coal balls. Sinnatt (3) states that fusain occurs in two forms, "the first a hard compact variety occurring rather rarely, which can not be pulverized by pressure of the fingers the second type is the common substance" -- that is, a very friable, easily pulverized material. The writer has also found the two types of fusain in the same coal bed and has observed that the hard variety contained considerable calcium carbonate, which probably entered the material in situ by infiltration. Sinnatt further remarks that the layers of fusain (soft type) usually contain less moisture than the coal (or lose it more readily on exposure), and when exposed they quickly change to flocculent powder so that the fines of the coal as mined are likely to contain a major proportion of this substance.

Jan 1, 1929

By Francis E. Federspiel

Based on the investigation by the Bureau of Mines, tungsten is the principal metal found in the study area; gold and silver were the primary metals found at one property. Tungsten occurs in tactite zones formed near contacts of calcareous metasedimentary with granitic intrusive rock. Gold and silver were found primarily along quartz veins in granitic rocks; small amounts of those petals also occur in the tactite zones. Since 1856 approximately 200 lode claims or relocations have been recorded, mainly in the southwest corner of the study area. Tungsten production in this part of the area has been inure than 7,800 short ton units (70,800 kg) of tungsten concentrates; about 4,800 short ton units (43,500 kg) were from the Mud Lakes Mine; and 3,100 short ton units (27,200 kg) were from the Rainbow Mine 1/.

Jan 1, 1981

Coal has been mined in the central Appalachian coalfields of southern West Virginia, western Virginia, and eastern Kentucky for more than a century. The dwindling reserve base consists in large part of coal that would have been considered unmineable by earlier generations. Nearly every current operation is working on a property where coal has been extracted in the past, from seams either above, below, or both. NIOSH is conducting research aimed at helping mine planners prevent hazardous conditions due to multiple seam interactions. To-date, more than 300 case histories have been collected from underground mines, mainly from central Appalachia. This paper focuses on several of the more challenging situations that have been encountered, including: • Room-and-pillar development 20 ft (6 m) beneath full extraction workings at a depth of 1,000 ft (300m) of cover (Virginia) • Pillar recovery 45 ft above full extraction workings at 900 ft (270 m) of cover (Virginia) • Near-simultaneous room-and-pillar mining with pillar recovery with 40 ft (12 m) of interburden and 1,500-2,000 ft (450-600 m) of cover (Kentucky) • Longwall mining directly beneath main entries in overlying seams (West Virginia) • Some of these operations have been highly successful in overcoming the challenges, others less so. The lessons learned from their experience will help ensure that these and similar difficult reserves can be mined safely.

By Charles D. Haynes

Outside air for ventilating coal mines in Alabama varies considerably in both temperature and moisture content during the year. Alternate condensation and evaporation of the moisture on mine roofs may result in stresses detrimental to the strength of mine roof. It is well known that the clays in shales absorb moisture, and many investigations have noted the weakening of shales by absorption of moisture. Parker (1970) concluded that there is an annual cycle of rock deterioration in mine roof rock caused by the annual temperature-humidity cycle at the surface. He further noted that moisture reduces the strength of dry rock by one-half, that moisture added to dry rock can cause failure in compression, and that drying of wet rock causes tensile stress buildups by shrinkage. His recommendations for alleviating the moisture-temperature problem was to seal the rock in critical areas and to control ventilation so that air temperature will be lower than rock temperature. The latter recommendation will avoid condensation on the rock surfaces. Hartmann and Greenwald (1941) published the results of a very comprehensive experimental project to determine the effect of temperature and humidity changes on the behavior of mine roof. Their general conclusions included statements that roof rocks were very sensitive to moisture changes, but had low coefficients of thermal expansion. The coefficients were twice in the direction normal to the bedding plane as compared to the parallel

Jan 1, 1975

By M. D. Balen

The U. S. Bureau of Mines has undertaken the development of mineral industry cost escalation factors to enable the estimation of mineral development and extraction costs for mineralized sites in Alaska throught the use of the Bureau's Cost Estimating System v2.0 (CES 2.0). For the purposes of this document, all calculations are based on, and reflect the economic environment in Alaska in July 1992. The greater cost of mining in Alaska as compared to the contiguous-48 States can be estimated for Alaskan mining operations through (1 ) the analysis of capital and operating costs for analogous mine and mill plants in operation in the contiguous-48 States; (2) the hypothetical relocation of mine and mill plants from their actual location(s) to Alaska by making engineering modifications to the mine and mill plant design as required by the Alaskan site characteristics; (3) calculation of the cost of the required engineering modifications and; (4) the escalation of all costs to a level representative of the economic environment in Alaska at some specific point in time.

Jan 1, 2011

By Harry W. Campbell

A Bureau of Mines investigation identified no mineral deposits in the Lost Creek RARE II area. Sand and gravel has been mined from alluvial flood plain deposits just outside the RARE II boundary. An oil and gas lease application which includes the eastern portion of the RARE II area is pending. Abundant basalt in the area can be crushed and used as aggregate; but it could not compete with similar deposits in more favorable locations, or with cheaper substitutes such as volcanic cinders or sand and gravel which are available outside the study area closer to major markets. No indication of coal or geothermal energy resources was found. INTRODUCTION Location and Access The Lost Creek RARE II area encompasses 8,300 acres (3,400 ha) of Lassen National Forest in north-central California, about 20 mi (30 km) north of Lassen Peak. The closest city is Redding, California, 50 air mi (80 km) southwest. Peripheral access is provided by State Highway 89 passing near the western RARE II boundary (fig. 1). The Pacific Crest Trail traverses the western margin of Hat Creek Rim adjacent to the eastern boundary of the area.

Jan 1, 1983

By George A. Savanick

This paper reviews advances in the art of borehole (slurry) mining made by the Bureau of Mines from 1974 to 1980. The design of a proto-type borehole-mining tool (BMT) developed by the Bureau of Mines is pre-sented along with production data, reclamation data, and an application of the BMT to the mining of coal, uraniferous sandstone, oil sands, and phosphate ore. The BMT was first used near Wilkeson, WA, where steeply pitching metallurgical coal was mined at 8 st/h from a depth of 25 to 75 ft. Next, 940 st of uraniferous sandstone was mined at 8 st/h from a depth of 75 to 100 ft in Natrona County, WY. One thousand short tons of oil sands was mined in Kern County, CA, at the rate of 14 st/h from a depth of 110 to 150 ft in 1979. Most recently, 1,700 st of phosphate ore was produced at 25 st/h from deep (230-to 250-ft) deposits in St. Johns County, FL. Progressive improvements were made in the borehole mining technique. These include the use of the hydrostatic head of a water-filled borehole for roof support, and the development of methods to survey and backfill mined-out cavities.

Jan 1, 1987

By Thomas Gales

Longwall mining has a high potential for producing bulk production from a single face. Production is interrupted for a considerable time when it is necessary to move the equipment to a new block of coal. The frequency of such moves can be reduced by increasing the dimension of the block to be moved. Merely doubling the tonnage in a block to be mined may increase production by more than 21,000 tons per year. The time taken to move the equipment can be reduced by careful preplanning, industrial engineering analysis, and specially designed equipment. Reducing its move time from 30 days to five days can increase production by more than 25,000 tons per year. Increasing the panel dimensions and reducing the move time can give an increase in pretax profits of more than $600,000. A comprehensive bibliography is included.

Jan 1, 1977

By Robert P. Vinson

This Bureau of Mines report presents the results of tracer gas studies conducted at three facilities where bagger hoods had been installed several years ago to remove airborne silica dust from the vicinity of the bagging operator. The studies indicated that for optimum benefits makeup air must be evenly dispersed, the hood enclosures and duct systems must be as airtight as possible, the average intake air velocity of each hood should be at least 200 fpm, and the hoods and duct systems must be properly maintained.

Jan 1, 1981

By E. P. Youngman

This paper is one of a series of digests of foreign minim legislation and court decisions that is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries. This interpretation of the minim lams of Ceylon has been prey tired from the best available information in Washington and is released subject to amplification and correction, if necessary, by United States foreign-service officers. INTRODUCTION Ceylon has no basic mining law; the general rules governing the granting of mineral concessions and affecting legal titles of concessionaires are laid down in Ceylon Government ordinances or are found in the authorized forms for licenses and leases. The material available in the preparation of this digest is as follows:

Jan 1, 1933

By William R. Wessels

This report describes a field survey and laboratory investigation into the causes of failure of resiliently clad screen decks applied to coal preparation plants. Blinding of screen deck perforations and delamination of the resilient cladding are studied and mechanisms responsible for these failure modes are hypothesized. A laboratory test program to simulate the mechanisms was begun and abandoned when it became apparent that meaningful test results would require a substantially redirected effort. No meaningful test data was obtained from the laboratory simulation.

Jan 1, 1982