Search Documents

By Mark I. Copeland

The Bureau of Mines investigated the effect of up to 1 wt-pct of copper and silicon on the heat treatment response and hardness, tensile, and impact properties of hot-rolled medium-carbon steels. The steels were prepared by induction melting and fabricated into plates by forging and rolling. The tensile strength of 0.2-wt-pct carbon steels containing 0.3 wt-pct silicon was affected significantly by copper in both the hot-rolled and heat-treated (600° C) conditions, whereas the tensile strength of the 0.3-wt-pct carbon steels was less affected. A 600° C treatment was considered optimum as a post-rolling treatment to strengthen the steels by copper precipitation. Strengthening of 0.2-wt-pct carbon steels by silicon was reduced by increasing copper contents.. Optimum impact strengths occurred at about 0.3 wt-pct silicon in 0.2-wt-pct carbon steels containing 0.6 and 0.8 wt-pct copper. The impact strengths were lowest for 0.2-wt-pct carbon steels containing over 0.8 wt-pct copper and greater than 0.3 wt-pct silicon, especially in the heat-treated condition. Copper and silicon solutes and copper precipitates strengthened the steels. This effect was augmented slightly by strengthening through grain refinement by these solutes.

Jan 1, 1973

The purpose of the contract was to develop an improved coal mine dust sampler whose electrical-to-mechanical energy conversion efficiency would be superior to that of the presently available equipment. The electrical to (pressure) X (volume) conversion efficiency directly affects the size and weight of the air samplers. At least half of the mass of present equipment is composed of the rechargeable batteries. Any increase in efficiency will allow this mass to be reduced or the flow rote to be increased.

Jan 1, 1974

By R. V. Ramani

One area of study in the Coal Mine Injury Analysis project was to illustrate and enhance the ability o mine safety management personnel to apply analytical techniques to Injury experience data and to justify requests for funds for safety enhancement actions on a cost/benefit and other quantitative basis. Four volumes of this final project report detail (1) the objectives and scope of the mine safety management research, (2) the results of literature review, and case studies, and (3) models developed for mine safety management. The four volumes are titled as Volume III: Mine Safety Management, Volume IV: Analytical Techniques for Mine Safety Management; Volume V: Mine Safety Management Case Studies and Volume IX: Training Cost Model. In this volume, the application of the quantitative procedures to mine-specific accident/injury experience data is discussed in detail in the form of case studies. The accident data from three mines are analyzed, and recommendations for training are proposed for each of the mines on the basis of this analysis. The procedures to apply cost-benefit analyses are described along with the cost benefit ratios for the training program/policies for the mines.

Jan 1, 1993

By W. R. K. Wu

Studies are reported on the structure of coal and coke with the graphical , statistical densimetric method based on the relation between the molecular volume per carbon atom ( M / C ) and the atomic hydrogen - carbon ratio ( H / C ) . Previous work , mostly from chemical and physical investigations , is critically reviewed . Difficulties in evaluating the ring increment are demonstrated for coal and coke for the statistical densimetric method based on the additivity of atomic volumes of constituent elements . A new diagram is presented for the graphical method . Methods are introduced for correcting M /C and H/C for the presence of minor constituents in coal and coke . With the graphical method , the fractions of aromatic carbon atoms in the total carbon atoms are estimated for a coal , a resin , and 5 petrographic components ; the types of condensed structure in the fundamental units of molecules are discussed for these substances , 28 coals , and 6 " average " cokes at 500 ° to 1,000 ° C. It is also shown that the number of rings in the fundamental units of coal generally increases with increasing rank and that of coke , with increasing carbonization temperature .

Jul 1, 1960

By S. Peterson, E. C. Westman, P. L. Swanson

Coal bumps are brittle, violent failures associated with high stresses and competent host strata. To study bump mechanisms, conditions in the vicinity of a deep longwall mining face in bump-prone strata were monitored using three discrete systems. First, a microseismic monitoring network recorded mining-induced seismic events throughout the mine and surrounding strata. Second, pressure variations and distributions on the longwall shield legs across the face were recorded. Last, tomography surveys imaged seismic transmission properties ahead of the face. Results from the three systems were correlated in an effort to increase understanding of mining-induced stress redistribution and bump potential. An initial, one-week study showed that the correlation between averaged tomogram values and seismically active areas had a coefficient of correlation (R) of 0.89. Further results of these studies demonstrate that the tomography system is capable of imaging heavy shield-leg loading and bump-prone conditions prior to them disrupting the face operations.

By Frank Parrish

History and performance data of 17 water-injection projects in Cooke and Grayson Counties in north Texas are presented for the purpose of studying and comparing operating practices and oil-recovery techniques. Water is injected into Strawn and Canyon sands of Pennsylvanian age. The principal formation flooded is the Strawn, which ranges in depth from 725 to 6,900 ft in the projects covered. Estimated ultimate recoveries range as follows: Primary, 22 to 494 bbl per acre ft; and secondary; 63 to 296 bbl per acre ft. These figures represent the following percentages of original oil in place: Primary, 10 to 46 pct; and secondary, 8 to 23 pct. Shallower projects; 725 to 1,500 ft in depth, had higher average primary and secondary recoveries than did deeper projects. Crude-oil gravity, which ranges from 20° to 45° API, was not relatable to yield of secondary recovery oil. Analysis of the data indicates that five-spot injection patterns will yield the highest percentage of oil remaining at start of flooding; that is, 28.8 pct for five-spot injection patterns, compared with 20.8 pct for line-drive patterns and 11.6 pct for random patterns. Waterflooding in this area appears to be very successful. Secondary recoveries of most projects are expected to nearly equal primary recoveries.

Jan 1, 1963

By L. W. Brandt

The Bureau of Mines, as part of its mission to effect pollution abatement, conducted research to study various means of dewatering Florida phosphatic clay wastes and reclaiming mined lands. The work was done in cooperation with 10 Florida phosphate companies. During this work, a novel technique to effectively dewater phosphatic clay wastes was developed. The solids contained in the clay waste slurry are slowly compressed by moving wire mesh screens through the system. In a typical application, the screens were moved downward, compressing solids ahead of the screens. The rate of movement of the screens is an important variable in the process. It is believed that the moving screens distort the gel structure of the phosphatic clay system and cause the release of water. Samples of 18 clay wastes, including a high-grade attapulgite from beneficiation plants of the Florida phosphate field, were studied using the method. Typical samples were concentrated from initial solids of 4.7 and 11.9 percent to 16.8 and 25.2 percent, respectively, in 3-1/2 days. The high-grade attapulgite sample was dewatered from 2.7 percent solids to 13 percent solids in the same period.

Jan 1, 1980

By J. Walden, J. Rhoades, R. E. Miller, R. Gibbs, P. Boman

Accelerometers and pressure transducers, mounted in suspension components, can be used to monitor the ride of haulage trucks. Presently, it is difficult to tell what caused a jolt to the truck using either pressure or acceleration data alone. When information from a global positioning system (GPS) is recorded at the same time as shock pressures or acceleration data, the exact location of an event can be determined. Mine management can then determine what caused the jolt to the truck. This research is part of a National Institute for Occupational Safety and Health (NIOSH) project called "Engineering controls for reduction of jolting/jarring injuries in surface mines." NIOSH is investigating how the work environment of haulage truck drivers can be improved. The US Mine Safety and Health Administration (MSHA) notes that, between 1986 and 1995, 60% of the back injuries were to haulage truck drivers in metal/nonmetal surface mining. Personnel from Phelps Dodge suggested that combining acceleration data with information obtained from a GPS could generate results with a variety of uses. Therefore, researchers at the Spokane Research Laboratory (SRL) began investigating how to tie acceleration and GPS data together. It was originally thought that this tool would be used primarily for road and truck maintenance. However, as research progressed, it became apparent that it would also be useful in providing feedback about equipment operations and identifying unusual causes of jolting. Experimental approach Available components that function well by themselves were linked for the purpose of proof of concept. Using a Modular Mining Systems (MMS) product called Vital Signs, SRL researchers took an Aero-Marine Products (AMP) acceleration recorder and hardwired it to MMS Dispatch equipment already installed on a truck. AMP is one of several manufacturers of acceleration recorders frequently used to monitor freight during shipping. MMS Dispatch is used for production accounting and truck dispatching and uses GPS tracking. Through Vital Signs, an analog or digital alarm signal can be recorded. Steve Rhoades, of MMS, wrote unique code that links the Vitals Signs data and GPS location and stores this data in an ASCII log file. SRL researchers installed the equipment in a Caterpillar 793 haul truck. The result was a working prototype. Figures 1 and 2 show the instrument installation in the truck. Discussion From 8:30 pm on Sept. 14, 1998 until 6:50 am on Sept. 15 1998, 899 jolts above a threshold of 2 g (1 g is the acceleration of gravity. It is either 9.81 m/s2 or 32.17 ft/ s2.) were measured on the test truck. Some sections of the haulage road produced most of the events, while

By J. C. Gerdeen

SAP-S information on the following element types are included in this appendix: Type 1. Three-Dimensional Truss and Bolt Element Type 4. Two-Dimensional Finite Elements Type 8. Variable-Number-Nodes Thick Shell and Three-Dimensional Elements Type 9. Two-Dimensional Joint Element (to be used with Type 4 elements) Type 10. Three-Dimensional Joint Element (to be used with Type 8 elements) Additional SAP4 elements, Types 2, 3, 5, 6, 7 and 12, are also contained in SAP-S and information on these elements is readily available in any SAP4 user's manual. These elements are as follows: Type 2. Three-Dimensional Beam Elements Type 3. Plane- Stress Membrane I-r .n Elements Type 5. Three-Dimensional Solid Elements (8 Node: Brick) Type 6. Plate and Shell Elements (Quadrilateral) Type 7. Boundary Elements Type 12. Three-Dimensional Straight or Curved Pipe Elements

Jan 1, 1976

By Harvey L. Pastan

The purpose of the investigation and analysis described in this report is to assess the data flow requirements that are required for remote supervisory control of a continuous mining system. Since these control concepts as applied to continuous underground mining are still in a formative stage at the present time during the first half of 1975, assumptions had to be made based upon engineering judgment as to what embodiment of mining machinery and control methodology seemed most feasible for achieving such a system. Based upon these assumptions and estimates of the control system's accuracy and response requirements, it was then possible to estimate the communication requirements for the assumed system configuration. 2. Approach The team members responsible for this study visited numerous coal mines to observe room and pillar mining operations in both high and low coal. The objective was to observe the methods of operating a variety of continuous mining machinery and haulage equipment with a view toward defining the problems to be overcome in the application of automation to the coal extraction process. Descriptive information concerning the mining equipment was obtained through contacts with the manufacturers. Conferences with Bureau of Mines personnel, equipment manufacturers and developers, and mine operators were held to explore the current thinking and developments being pursued toward automation and increasing both production and productivity.

Jan 1, 1975

By B. J. Moore

This Bureau of Mines publication estimates that U.S. helium resources as of January 1977 were 710 billion cubic feet. These resources are broken down into four classifications, as follows: Helium in measured natural gas resources and in storage, 201 billion cubic feet; helium in indicated natural gas resources, 150 billion cubic feet; helium in hypothetical natural gas resources, 175 billion cubic feet; and helium in speculative natural gas resources, 184 billion cubic feet.2 Most of the helium in natural gas is presently dissipated as natural gas is consumed as fuel and for other purposes. Helium resources of the United States may also be divided into three other categories: (1) Depleting and undiscovered natural gas resources, 589 billion cubic feet; (2) nondepleting natural gas, 83 billion cubic feet; and (3) storage, 38 billion cubic feet, of which 37 billion cubic feet is federally owned and 1 billion cubic feet is privately owned. The United States does not have any significant leasehold rights in the depleting fuel gas resources. However, through the Department of the Interior, it does have leasehold rights to about 70 percent of the helium found in nondepleting natural gas, and it owns over 90 percent of the helium in storage.

Jan 1, 1979

By Frank E. Cash

The work of the United States Bureau of, Mines is concerned primarily with the prevention of accidents in the mining, petroleum, and allied industries. This report analyzes the fatal accidents in the coal mines of Tennessee and gives the pertinent factors in tabular and descriptive form, with interpretations and suggestions to operators, workers, and the State Division of Mines for the future prevention or reduction of accidents in coal mines. ACKNOWLEDGMENTS This study was made possible through the cooperation of A. W. Evans, chief mine inspector of Tennessee, and his secretary, Miss Hiliary Penny, who made available the department records and assisted in the segregation and assembly of the data.

Jan 1, 1935

By A. L. Podia

The purpose of this research was to develop a system capable of detecting changes in the structure of rocks, leading to failure of mine roofs, and/or excavations. A prototype system was developed, field tested and delivered to the United States Bureau of Mines for further evaluation and research. This system is based on the analysis of acoustic signals generated on the surface of the roof by an impact device and which are reflected or backscattered by flaws and discontinuities in the rock. The specially designed impact source is capable of generating high frequency acoustic signals with excellent repeatability. The system can also be used in conjunction with conventional acoustic pulse transducers. The received signal is digitized and the data transferred to a minicomputer for processing and display. This capability allows the immediate determination of wave velocity and/or distance to a reflecting interface. Various data processing techniques such as averaging, differentiating, and comparing of different signals can be selected by entering the appropriate commands on the keyboard. Being a programmable system it is possible to implement more advanced signal processing techniques. All results as well as the signal are displayed on a CRT. Furthermore, a permanent record of the data can be generated on paper tape, which can be reentered and processed at a later date. A communications interface allows transmission of the sampled signal to a large scale re-mote computer. The system was tested extensively in the laboratory, and field tested at the York Canyon Coal Mine. These tests proved the feasibility of operation in the mining environment. Results indicate that further investigation and development will have to be undertaken to fully develop the potential of this system in satisfying the goals of this research.

Jan 1, 1973

By Paul G. Swanson

This investigation was conducted to identify the principle causes of spoil instability problems in the Eastern Coal Province. The study was also conducted to develop a matrix to predict the strength and groundwater parameters necessary to conduct stability analyses on a proposed reclamation scheme. Suggestive methods to reduce spoil instability potential are also included. Numerous physical property, strength, compressibility, chemical and mineralogical tests were conducted on mine spoil samples obtained from 11 different surface mine sites. Site characteristics that influence the position of the post reclamation groundwater table were identified. Distinct regions within the Eastern Coal Province with high incidences of surface mine slides or high landslide susceptibility were identified. The application of the predictive matrices developed in this study is for surface mine sites mined and reclaimed in general accordance with the Surface Mine Reclamation Control Act of 1977. A review of current mining practices and the relative effect on spoil stability is included.

Jan 1, 1983

By Jose P. T. Agapito

Several underground coal mines currently operating in the Beckley District of West Virginia are experiencing serious roof and floor problems. A significant portion of the estimated two billion tons of coal resources may be lost as a result of these ground control problems. Preliminary studies by the Bureau of Mines indicated that these problems are due in part to a high horizontal stress field. During this contract study, a field program was conducted to quantify the horizontal in situ stress. A total of 14 overcoring sites (using the Bureau of Mines strain-relief overcoring technique) in five mines were drilled producing 53 data sets. Analysis of the data was done to provide in situ horizontal stresses for each of the five mine, and for the district as a whole. Stress data indicate horizontal stresses far in excess of that predicted by theory and in some cases, up to six times the estimated vertical stress. In addition to the field testing, a detailed computer modeling study was conducted using finite element and boundary integral (displacement discontinuity) methods. Verification of in situ stresses was obtained by the models and analysis of various development geometries, mining methods and remedial techniques were conducted. Recommendations for reducing ground control problems and future studies are presented.

Jan 1, 1980

By E. D. Gardner

This paper is the third of a series of three on placer mining in the western United States. The first paper4 discusses the history of placer mining in the Western States and the production of placer gold, geology of placer deposits, location of placer claims on public lands, sampling and estimation of gold placers, and classification of placer-mining methods, together with hand-shoveling and ground-sluicing. The second papers deals with hydraulicking, sluice boxes and riffles, recovery of gold and platinum from placer concentrates, treatment of amalgam, and marketing of placer gold. The discussion of sluice boxes and subsequent subjects in the second paper applies to all forms of placer mining. The present paper treats of dredging and other forms of mechanical handling of placer gravels, and drift mining.

Jan 1, 1934

By B. M. O'Harra

Zinc smelting is frequently termed a ba.ckward art. The term is hardly true, for great progress has been made in recent years in the design and in the thermal efficiency of the retort furnace, in the quality of retorts, in the recovery of zinc, and in the ability to treat more impure and complex ores. The fact remains, however, that the peculiar physical and chemical properties of zinc have delayed such immense advances-large smelting units, high recovery, lowunit costs, and ability to treat low-grade ores-as have been made in the metallurgy of lead and copper. In current retort-smelting practice, the ores, if carbonates, are calcined to remove carbon dioxide; or, if sulphides, are roasted to remove sulphur. The sulphur must be eliminated as completely as possible, usually to less than 1 per cent. This means that the roast must be continued for a long time at a high temperature, with resulting high cost and small capacity per furnace. The roasted ore is mixed with about 50 per cent of its weight of reducer, which may be fine coke, anthracite, or nonbituminous coal. This mixture is charged into horizontal fire-clay retorts. The retorts used in this country are about 8 inches in internal diameter by 4 feet in length and hold 50 or 60 pou~ds of ore. The diameter of the retort is limited by the tirrie required for the heat to penetrate to the center of the charge; the length by the strength of the retort, which at the high temperature employed can not support the weight of the charge if the span is more than about 50 inches. The retorts are heated externally by coal, natural gas, qr ·producer gas to a temperature of 1,200° C. or more. The zinc oxide is reduced to zinc, which is volatile at this temperature, and passes into a conical fire-clay condenser. attached to one end of the retort, where it conde_nses to liquid zinc and is removed. Twenty-four hours are required for distillation, and because of the low heat conductivity of the retort walls 11.nd of the ore charge itself, the heat efficiency even of the most modern regenerative furnacei;; is only about 12 per cent. The retorts have a short life, 30 to 6Q days, at the high temperature required-; zinc losses are heavy, usually 10 per cent or more; and the proportion of impurities in the retort charge must be carefully controlled to prevent the rapid corrosion of retorts. For these reasons, much work has been done in an e:ff ort to, find cheaper and more efficient methods o.f recovering zinc from its ores. Various methods have been proposed for smelting in the blast furnace. Some of these contemplated the production of zinc vapor and its condensation to liquid; others attempted to produce liquid zinc directly by smelting under pressure. It is now realized that fundamental difficulties render these proposals impracticable. The electric furnace for smelting offers obvious advantages in the way of the efficient utilization of energy, large units, easy attainment of high temperatures, and the possibility of treating complex ores. E. H. and A. H. Cowles first suggested a design for an electric furnace for the reduction of zinc ores and patented their process in 1885. Their attention was soon directed to other uses for their furnace and nothing further of importance was done in the electric smelting of zinc until about 1900. Several investigators then started work upon various processes and had more or less success. The chief difficulty they encountered was the impossibility of obtaining more, than a small amount of the zinc as liquid metal because most of the zinc vapor condensed as blue powder. Interest in the electrothermic metallurgy of zinc increased, many patents on processes and furnace design were taken out, and the literature on the subject grew, until in 1914 and 1915 the problem seemed to be approaching solution. About this time the hydrometallurgy of zinc, the development of which had been lagging somewhat behind that of the electrothermic metallurgy, sprang into the limelight and a commercial process was soon perfected. This rapid development, perhaps aided by the war premium on the high-grade spelter produced by electrolytic deposition, distracted attention from electric smelting to some extent, though progress continued. With the perfection and standardization of the electrolytic process has come a better realization of its limitations, especially the necessity for large-scale operation ·and the difficulty of obtaining high extraction. Because of these limitations the electrothermic metallurgy of zinc still has a field of its own and in fac-t promises to become a strong competitor of both hydrometallurgy and retort smelting except under conditions highly favorable to the latter methods. Because of the imperfections of the retort and electrolytic processes and the promise that the electric furnace offers in overcoming these imperfections, the. United States Bureau of Mines, in cooperation with the Missouri School of Mines and Metallurgy, has undertaken a study of the electrothermic metallurgy of zinc.

Jan 1, 1923

By Tuncel M. Yegulalp

The objective of this study was to categorize mining operations in the stone, and sand and gravel industries into areas of similar ground control functions and define initial factors affecting operational safety in each area, by means of utilizing publicly available data, telephone interviews and on site observations. The findings and recommendations presented in this report are based on the information collected during the two phases of the project. They also contain, in part, the collective qualitative opinion of the operators with respect to government rules and regulations on ground control safety and the implementation of these rules and regulations by government inspectors.

Jan 1, 1981

By J. R. Thoenen

In Progress Report 1,4/ a number of facto mere demonstrated and conclusions drawn from experimental tests and records made during commercial blasting operations at a number of quarries. For example, the tests showed (1) that vibrations received on outcrops were of comparatively

Jan 1, 1938

By Clark F. Grain

These investigations were undertaken as part of the Bureau of Mines program for the development and evaluation of high temperature nonmetallic materials. This report consists of thermal expansion and phase inversion measurements by high-temperature X-ray diffractometry on the principal oxides of beryllium (BeO), calcium (CaO), titanium (TiO2 ), zirconium (ZrO2 ), hafnium (HfO2), and thorium (ThO2); all were high-purity commercially available oxides. Thermal expansion values were calculated from unit cell dimensions measured at selected temperatures. Expansion was determined parallel to each major crystallographic axis for the anisotropic oxides: BeO, TOi2, ZrC2, and HfO2. Combined random and systematic errors in the thermal expansion values are considered to be less than 3 percent of the total expansion at 500° C. and approximately 2 percent at 1,000° C. No hysteresis in the expansion curves was noted between heating and cooling cycles. The Bureau's values were compared with published expansion measurements obtained by X-ray diffraction, dilatometric, interferometric, and telemicroscopic techniques. For anisotropic oxides, average linear expansion values were calculated from the volume expansion.

Jan 1, 1962