Search Documents

By R Castedo, L. M. Lopez, J. A. Sanchidrian

In 2014 the authors presented results from 13 tests made with two blasting seismographs on a vibration exciter. They measured coupling transmissibility as function of frequency (i.e. ratio of the velocity of the sensor mount to the velocity of the ground motion) from 16 to 200 Hz at one or two vibrations levels (5 mm/s or 0.2 in/s, and 20 mm/s or 0.79 in/s) with mounts freely placed, sandbagged, and anchored to a granite slab firmly attached to the plate of a vibration exciter. As the memory capacity of one of the seismographs prevented to cover low frequencies, e.g. 4-16 Hz, a new measuring campaign has been recently made to extend the study down to 2 Hz. In this campaign, two more techniques, in which the sensor mounts were fixed with thermal adhesive or a combination of duct tape and gypsum plaster, have been also investigated from 2 to 200 Hz at 5 and 20 mm/s. Free and sandbagged mounts lead to a weak coupling of the mounts to rock, so that transmissibility depends on the characteristics of the imposed rock motion (peak velocity and frequency). Measurements are accurate only at low frequencies (below 17 Hz for free mounts and 10 Hz for sandbagged) in the tested conditions (velocities up to 20 mm/s). Above these frequencies, ground motion in the measurement can be modified by a factor of 0.16 to 1.22. Anchored, glued and plastered mounts achieve a stiff rock-to-ground coupling, ensuring consistent measurements for the frequencies commonly found in blasting independently of the vibration level and the mount characteristics

Jan 1, 2015

By He Guangyi

Combining living examples, the paper introduces the controlled chamber standing shot of more than 3000t explosives initiated at one time with Nonel under complicated circumstances and the experience obtained to keep environment safe and favour mechanical rock cleaning.

Jan 1, 1998

By Sushil Bhandari, Amit Bhandari

Drilling and Blasting are core operations in a mine. They impact all the downstream operations and their costs. Digital technologies exist for optimizing both drilling and blasting for many years. However, these technologies have largely been non-integrated and non-real time. This gap results in sub-optimal drilling and blasting operations. Also traditionally focus has been on optimizing individual areas (drilling or blasting and subsequent subsystems). Industry has largely lacked real time or near real time integration available to the user in the field and in the office. In this paper, a case study is presented of a large global cement company using a cloud and mobile based platform across 17 of their mines consistently over a large number of users over a period of over two years. The use of a blast platform is detailed which include blast designs, blast data collection and the trends in terms of results. On the drilling side, this paper describes the ability to capture drill logs, plod reports etc. Also actual drilling information in the field using a mobile device and its real time synchronization with a blast designer to provide visibility of expected fragmentation and vibration levels based on the drilling done. Key parameters such as hole ID, design depth, actual depth, hole status, designed and actual charge (length and weight), designed and actual stemming length are captured. The case study also highlights the challenges in technology adoption and implementation in mining in drilling and blasting. Making drill and blast results predictable should be the desired direction. Also digital technology tool adoption has been seen at the biggest miners – not so much in mid-sized miners or drill and blast contractors. Benefits of this platform on the safety side are highlighted including predictions on safety parameters and appropriate alerts if blast safety parameter / clearance zones are not met. The safety parameters are made available visually to the operator using maps and / or on drone images. Future possible improvements in the digital technology platform at the site are also highlighted including greater possible automation.

By Greg Wyartt

In the Pilbara region of Western Australia, an iron ore mine is undertaking a high wall cut-back to improve stability and allow access to deeper ore deposits. Several sections of the wall have been classified geologically sensitive due to unstable localised geology, and therefore an engineered approach to vibration critical blasting was required. The use of electronic detonators allowed multiple signature (seed) holes to be incorporated into a production blast adjacent to the geologically sensitive area, therefore providing baseline vibration data to be used for future modelling with the added advantage of eliminating unnecessary pit closure downtime typically associated with a signature hole program. All subsequent blast patterns also incorporated multiple signature holes to provide additional data and allow continual updating – and therefore improved accuracy - of the blast prediction model.

Jan 1, 2018

By Harry Verakis, Thomas Lobb

Blasting accident data over a 30-year period (1980-2010) are summarized and presented for all types of surface and underground mining operations in the USA. The historical record of injuries from blasting accidents in all types of mines continues to show a significant decline. The overall decline in mine blasting injuries in the U.S.A. has resulted from advancements in blasting technology, training and improvements in blasting products and blasting processes. Some of the technology advancements such as safer blasting agents and computerized bulk vehicle loading, electronic detonators and remote operated blasting systems, and computerized blast design have and continue to significantly contribute to improvements in the historical blasting safety record. Also, the progress of significantly improving the safety of mine blasting has resulted from the combined efforts of miners, mine companies and operators, miners, unions, explosive and blasting product manufacturers, associations such as the International Society of Explosives Engineers and the Institute of Makers of Explosives and various government agencies.

Jan 1, 2012

By Deepak Vidyarthi

This paper deals with various measures adopted in protecting a conveyor duct (named after a Conveyor Belt that was numbered as ‘02’) housing a 1600 mm (63 inches) belt conveyor system in a large, heavily mechanized open cast iron ore mine, producing about 20.0 million tones of ore per annum.

Jan 1, 2008

By Oliver Finn

Gold dredging has made such rapid strides of late and there is such a widespread interest in this branch of mining that I venture to contribute a detailed account of the way in which a Keystone driller was used by me in California to loosen, by blasting, a very tight gravel deposit, preparatory to dredging. There is a great difference between “cemented gravel” and “tight gravel.” A truly cemented gravel is not a dredging proposition, while the tightest possible gravel, where there is no cement, can be made easy working by the following method of blasting:

Jan 1, 2008

By J. Pizarro

Any organization that subjects its activities to a continuous improvement methodology, aiming to optimize their processes and services, must be able to adequately measure the results of the implemented changes to pursue better outcomes. This is no different for mining companies. When it comes to blasting, an accurate fragmentation analysis can correlate blast design and rock mass parameters to particle size distribution, enabling us to further analyze the correspondence of specific design patterns, applied to specific rock mass properties and the result in measured fragmentation indicators. Over time, many tools were developed for us to obtain PSD data, albeit each of them had their own shortcomings. The first ones to be developed involved photographing the muck pile including a scale object, uploading those photos to a PC, and using specialized software to analyze each one. As a result, analysts would get a PSD curve that served as reference for the performance of the blast. This method, which is still used, has major shortcomings. The most obvious one is that it is only able to capture a slice of the blast, which corresponds to the exposed section of the muck pile the analyst has access to, and even there its reach is limited to the areas that are safe for getting close enough for placing the scale, which are not many. Consequently, this is a very limited way to get a fragmentation performance assess for a blast. Currently, autonomous systems are capable of taking continuous pictures of the muck pile. Installed on a shovel, conveyor belt or crusher feed, these systems can take a continuous stream of pictures that are later analyzed automatically without the need of human intervention. These systems greatly increase the volume of data and, consequently, we have a PSD curve that is more representative of the blast performance. However, this technology still had issues when trying to sample front end loaders mining operations or getting results from underground blasting due to the inherent difficulties of these operations. New algorithms used for capturing and processing data for front end loaders can overcome the harsh environment of their operations and produce PSD data in high vibration environments and difficult mining angles. For underground mining, algorithms can be used to sample each truck exiting the mine, giving a reliable source of fragmentation analysis that can be traced back to their stope of origin. The development of this technology extends the existing system’s capabilities and helps us in our efforts to improve fragmentation results with each blast.

Jan 1, 2024

By Rob Farnfield, Charlie Adhock

The measurement of near-field shock has always been an attractive proposition for those working in the field of explosive and blast performance. The most commonly employed technique involves the use of piezoelectric accelerometers. Although highly effective, these complicated devices are relatively expensive and are often destroyed in the blast event. This paper describes the development and field-testing of a shock sensor of sufficiently low cost to enable it to be routinely used in product blasting. This new device is based on piezoelectric wafer technology and does not require any external signal conditioning. The device is housed in a small cylindrical package with approximate dimensions of 30mm (1.2”) length and 5mm (0.2”) diameter. It has been determined that the most effective way of fixing the device to rock is in a small diameter hole with epoxy glue. Alternatively the sensor can be simply placed in holes filled with either water or bulk emulsion explosive.

Jan 1, 2005

By Ajoy K. Singh, B Mohanty, P K. Singh

A study was conducted to investigate the damage potential to underground multiseam openings caused due to vibration generated by open-pit coal mine blasting. The objective was to recommend optimal explosives weight per delay to be detonated in open-pit blasts to ensure the safety and stability of underground openings. Sixteen blasts with varying charge weights and initiation sequences were conducted at Samleshawari open-pit mine and eighty four blast vibration data were recorded in the Hingir Rampur underground colliery in India. Analysis of vibration data showed that roof of the underground openings vibrated with much higher amplitudes compared to those in pillars and floors. The amplifications of vibration in the roof at the junction were upto 4.3 times the pillar vibration. It was observed that coal chips detached from roof when the peak particle velocity reached 131 mm/s or higher. The vibration magnitude recorded was higher in upper-seam openings than in belowseam openings. Rapid attenuation of vibration was recorded in below-seam openings at similar locations. Appropriate particle velocity-charge weight-distance equations were established to calculate the safe explosive weight per delay to be detonated in open-pit mine for the safety of multi-seams workings of underground mine. The support for the galleries and junctions were further modified for the working seams to ensure greater safety.

Jan 1, 2011

By P D. Kasbanis, Lyall Workman

"The energy output of an explosive is typically calculated using an equation of state and computerapplications. Results are reported as weight and bulk strength, either in absolute terms or relative toANFO. The effect of the equation of state selected and the assumptions regarding the energy calculation are considered and interpreted for the purpose of blast design. It appears that variations in the heat of detonation which result from the selection of the equation of state and parameters associated with it are not sufficient to significantly affect blast patterns, explosive consumption and costs. However variations stemming from the use of “available energy” associated with a cut-off pressure are significant, suggesting in many cases large pattern expansions. The validity of the various approaches is discussed and blast design results based on the energy calculated by the different approaches are presented and evaluated."

Jan 1, 1996

By (Journal for the Fields of Gunpowder and Explosives) Germany (1914 Issues)

RBH Note: The following items are a deviation from the usual content of these articles, but I thought they were kind of interesting from an historical point of view (other than just explosives-history historical.) The interesting things to me are the military-related products, keeping in mind that World War I didn’t start until August, 1914, and then it was kind of an accident of political alliances gone awry. Obviously companies in Germany saw it coming. Of course, all the ads also included dynamite and safety explosives for mining and tunneling as well as the military items.

Jan 1, 2015

By Donald Thompson, Jessie Bonner, Ileana Tibuleac

Predicting ground motion from complicated mining explosions is important for mines developing blasting programs in regions where vibrations must be kept below certain levels. Additionally, predicting ground motion from explosions in complex 3D media is important for source size estimation for nuclear treaty monitoring. Both problems have been addressed under the development of a new series of programs including: 1) Generalized Fourier Methods to generate synthetic seismograms (Green’s functions) in 3D media for a moment tensor source implementation and 2) MineSeis3D, a program that simulates seismograms for delay-fired mining explosions with a linear relationship between signals from small size individual shots. To test the programs, three-component seismic recordings of three production shots at an iron mine in northern Minnesota were compared to synthetic waveforms in 3D media. Comparison of the observed and synthetic waveforms shows promising results. The shape and arrival times of the normalized synthetic and observed waveforms are similar for most of the stations. The synthetic and observed waveform amplitude fit is best for the vertical components in the mean 3D model but not as promising for the transversal components. The observed effect of spall on the waveform spectra was weak in the case of fragmentation delay-fired mining explosions. Commercial applications of the code could provide data needed for designing explosions that do not exceed ground vibration requirements posed by the United States Department of Interior, Office of Surface Mining.

Jan 1, 2005

By William Reisz

Over the years as surface mining operations have become more sophisticated, angle drilling has become a more popular blast design technique, especially in areas where overburden and stripping ratios have increased. Another method of blast design is the staggered pattern, which greatly improves explosives distribution within the blast. While both methods present some engineering challenges, this paper will discuss how the two methods can be combined to enhance fragmentation, improve cast percentage, drill production ratios and highwall control. A practical engineering approach will be presented as well as a discussion on the discipline required to maintain a quality blasting plan.

Jan 1, 2002

By Frank Sames

Ground vibration levels are generally predicted using equations such as the USBM equation implementing the scaled distance concept and describing geological and blast design parameters in a ground transmission constant.

Jan 1, 1995

The common approach of designing blasts on a trial and error basis is quickly coming to an end. When utilizing the full scale blast environment, trial and error can quickly become cost prohibitive and leaves much to be desired in terms of true blast diagnostics. In these situations testing is usually only continued until a perceived improvement is achieved and when the gross undesirables in blast results are removed. This does does not preclude, however, that further improvements of up to 100% or more can not be obtained.

Jan 1, 1991

By Brian W. Stump

Seismic networks provide the primary technology for monitoring compliance with a comprehensive test ban treaty. The design goal of the network is the identification of possible clandestine explosions detonated below the earth’s surface and possible in the oceans. Complementary technologies such as infrasonic, hydroaccoustic and radionucleide (particulates and noble gases) monitoring supplement the seismic monitoring covering explosions in the atmosphere and oceans. Seismic sources that will produce detectable signals will be both natural and man made in origin. Naturally occurring events include earthquakes, many of which are beneath the oceans or deeper than it is possible to drill, and volcanic eruptions. Accurate locations of such events to depths of beyond 10 km precludes consideration of these events further.

Jan 1, 1995

By J. Lindenau

One of the significant benefits of electronic detonators is their safety, especially their relative insensitivity to extraneous electrical energy. The various brands of electronic detonators on the market have different resistance to electrical stimuli, but all have safety structures designed to afford a significant level of protection. A common source of extraneous electrical energy is lightning. This paper discusses the nature of the energy that occurs with a lightning strike and the resistance offered by electronic detonators. Four actual cases of exposure of electronic detonators to lightning strikes are considered. Electronic detonators, like other initiation systems, are vulnerable to very close or direct lightning strikes. The incidents are a reminder that all blast patterns need to be vacated on the approach and during the progress of a lightning storm. 1. Orica

Jan 1, 2008

By Daniel Roy

This paper introduces a new, safer bulk emulsion loading system for underground mining operations. The features and benefits of the equipment, along with the use of Dyno Nobel Inc. patented gassed emulsion technology, is summarized in the application of a stope blast with very difficult and complex ground conditions. The paper describes methods used to optimize the amount of energy required to break the ore while protecting the integrity of the surrounding backfilled pillar.

Jan 1, 2003

By Mohsen Sanai, Paul Gefken

"SRI International has developed and patented* a castable dilute explosive tile @ET) that offersunique advantages over conventional high explosive. The primary advantages of DET are that itsdetonation pressure can be adjusted over a wick range and its impulse can be controlled independently by adjusting its thickness and configuration. Because DET has a much lower detonation velocity than conventional explosives, the pulse duration produced by DET is as much as 10 times longer than the pulse duration produced by conventional explosives for equal explosive weights. These features of DET present several advantages to the mining industry. For example, DET can be tailored so as to control fragment size and distribution to enhance extraction of desired elements from ore or breakup of specific regions."

Jan 1, 1995