Search Documents

By D. R. Wardrop, G. Walton

Paper presented at the UK minerals industry conference held in Leeds, UK, 3-5 April 1995. A description is given of the approach that has been taken to the design of the 550 000 000 t superquarry with a planned life of 60 years that is proposed for development. The quarry has been designed to replicate a corrie and a sea loch and will include excavated slopes more than 570 m high. The main geological and physical controls on the layout and the choice of development method are outlined. The operation phasing is presented and the geotechnical constraints on slope design and the feasibility of alternative quarry limits are discussed. Environmental considerations have been dominant in planning and the quarry has been specifically designed for closure

Jul 1, 1996

During a programme to determine the suitability of the UK site for deep disposal of radioactive wastes, geostatistical methods were used to characterise rock heterogeneity on the basis of seismic and wireline acoustic-impedance data. The data were analysed to yield semi-variogram models that quantified the three-dimensional spatial heterogeneity of acoustic impedance. These models were reconciled with geological interpretations of the area and used to generate simulations of acoustic impedance, with wireline acoustic impedance as conditioning data. The three-dimensional simulated images were compared with actual seismic acoustic impedance. The variography confirmed a vertical zoning effect in the Borrowdale Volcanics, showing that it is caused by preferential clusters of high acoustic impedance values corresponding to regions of relatively low porosity. The method provided realistic three-dimensional models from sparse, one-dimensional wireline data

Jun 19, 1905

By P. Varona, L. Lorig, M. Board, E. Chacon

Geomechanical factors at the mine are important and will become even more relevant as the pit expands and deepens. To address these demands a team was assembled to collect geomechanical information and perform numerical analysis. The west wall is the largest and flattest of all the design sectors in the pit and rigorous studies were carried out on this wall. The wall behaviour is controlled mainly by a set of steeply dipping joints within the slope in the Fortuna Granodiorite and a weak zone, the Zona Plastica, that extends vertically near the pit bottom. These features lead to large toppling displacements in the upper portions of the wall. Two numerical models were used to reproduce the general features of failure observed in the wall. The modelling indicated that a toppling mode of failure results from shear on the steeply dipping joints. The toppling leads to slumping or landslides whereby the west wall flows slowly downslope as the Zona Plastica compresses

Apr 1, 1996

By C. McCall, J. T. Knight, J. R. Ridley

Gold mineralisation in the gabbro sills is mainly stratabound to quartz- and Fe-rich, granophyric-textured units and is sited in undeformed, brittle quartz vein sets, which form pipe-like orebodies. Hydrothermal wallrock alteration consists of hornblende-plagioclase-calcite-quartz with minor biotite, garnet and chlorite and with arsenopyrite and pyrrhotite as the dominant sulphides. Geothermobarometric data suggest that gold was deposited at around 520 degrees C at 2.8-3.8 bar. Mineralisation is thought to have occurred during amphibolite-facies metamorphism. Fluid inclusion and isotope data indicate that gold mineralisation was the result of deposition from a low-salinity H2O-CO2-CH4 fluid of either metamorphic or magmatic origin. Although the Three Mile Hill deposit differs from others in the area in its wallrock-alteration assemblages, peak-metamorphic timing of gold deposition and distinct geochemical associations it forms a brittle stratabound ore body which suggests structural and gold-depositional mechanisms in common with those of the other gabbro-hosted gold deposits

Jun 18, 1905

By B. Denby

Paper presented at a meeting on: Artificial intelligence in the minerals sector, held in Nottingham, UK, 20 April 1993. The design and scheduling of open pit operations are consistent problems encountered by the surface mining industry. Numerous techniques and algorithms have been developed to assist the mining engineer in the creation of optimum development strategies. Virtually all the practical techniques that have been produced have concentrated on one of the aspects (limit definition or scheduling) at the expense of the other. It has long been recognised, however, that the two activities are intrinsically linked and thus solving either problem independently of the other can only ever produce sub-optimal results as a whole. This has been termed the "circular reasoning problem". It has also been recognised that, for all practical-sized situations, solving both problems simultaneously is virtually impossible using conventional techniques due to the massive size of the search space involved. A technique is presented which is based on a self-learning genetic algorithm, which provides a combined pit limit and extraction schedule simultaneously in order to maximise the NPV (net present value) of the extraction. The theory is developed in two-dimensions and a number of examples of its application are presented. It is proposed that this approach is a highly efficient, heuristic technique offering the potential to transcend the circular reasoning difficulties of separate pit limit and extraction scheduling systems. Extension of the technique into three-dimensions and its application to realistic problem sizes are discussed

Apr 1, 1994

By M. L. Leblanc, J. F. Burzynski, D. J. Mossman

A strong heterogeneity in the distribution of Sb+/-Au deposits exists within the North Atlantic Acadian-Hercynian domain. This is reflected in the regional disparity in Sb production among the various producing countries. This work focuses on the nature and distribution of Sb+/-Au occurrences in the Acadian-Hercynian domain. A summary listing of the general features of Sb-Au deposits found in this area is given

Dec 1, 1991

By A. Berckmans

The key variables in the financial analysis of a mining project include the metal price and the quantities of ore and metal. In general, if the metal price drops, the cutoff grade is increased so as to increase the average grade. This causes recovered tonnages of ore and metal to drop. Discussion is presented of the development of a new method to evaluate the relationship between the cutoff grade, z, the ore tonnage above cutoff, T, and the metal quantity above cutoff, Q. Detailed information is provided on the QTz curves for lognormal and inverse gaussian (Sichel's) distributions. Both these distributions are used as models for the grades in different types of ore bodies, and they are both T-symmetric. The geometry of the QTz curves is simplified, making it easier to work out the impact of minor variation in the parameter values for each distribution

Dec 1, 1996

By B. J. Breen, C. S. Mogg

Considerable borehole investigation work has been completed at a proposed site at Sellafield in Cumbria, supplemented by seismic surveys, other geophysical sensing and geological mapping. The focussing of investigation on the rock mass itself will be achieved by means of the planned underground rock characterisation facility, giving access to depths of about 800 m in the strong, low-permeability basement rocks of the Borrowdale Volcanic Group. Characterisation work undertaken during the sinking phase and interaction with continuing surface-based exploration and monitoring should permit a firmer assessment of the long-term safety of a repository. Key considerations in the choice of a design for the repository include the waste handling method, underground inlet cell, underground vaults, vault environment and environmental effects

Aug 1, 1994

By R. Sankey, L. Gatty, F. Bizzozero, G. F. Shannon, F. Savaglio, L. McDonald

State mining regulations in Queensland stipulate that a mine be provided with an earth installed on surface and that all underground equipment that needs to be earthed should be connected via a copper conductor to this surface grounding point. The regulations further require that all exposed metal surfaces in underground substations be connected to an earth. In a study of earthing conditions at Mount Isa mine it was found that the physical anchoring of metal work at substations (with rockbolts and associated steel mesh) also provides an excellent electrical connection to the country rock. It was established that not only is the mine's earthing system grounded at numerous underground locations but also that such anchor points offer, in general, a path to ground with lower resistance than does the legally required grounding point on the surface. It is recommended that metalliferous mines should utilise a multiple-earth system and not a run earth connected to a single, above-ground earth point

May 1, 1991

By G. W. Harris, J. J. K. Daemen

Slightly shorter, modified version also published in CIM Bull., vol.94, no.1047, Feb. 2001, p.52-55. To minimise ore dilution induced by blast movement in surface mines it is necessary to quantify such movement. This will allow more accurate location of the grade boundaries on the surface of a blasted rock pile before excavation. A method has been developed and tested for measuring accurately the direction and magnitude of subsurface blast movement, using a caesium vapour gradiometer and a real-time, differentially corrected global positioning system to locate the pre- and post-blast positions of magnetically enhanced target objects placed in blastholes inside a bench. The procedure does not necessitate disturbance of the blasted rock and the movement information is available sufficiently quickly to allow for modification of the selective mining boundaries for each surveyed blast. It was found that the maximum depth of target detection was 18 m and the overall accuracy was plus or minus 1 m horizontally and 1.2 m vertically

Jun 21, 1905

By D. Witchard, G. C. Penny

An important conclusion of the study is that altering the properties of the granulation water is a practical way of improving the sintering performance of blends that contain porous ores, and more work is under way to investigate other additives. Previous studies of iron ore blends containing pisolite ore showed that losses in sintering productivity were a result of deteriorating green-bed permeability. Pisolite ores are extremely porous and absorb a proportion of the water added during granulation. Although increased water addition could be used to counteract losses in productivity, the current study examined methods of inhibiting water absorption by pisolite ore as a means of improving productivity. Additives were used to alter the properties of the granulating water. With no increase in mix moisture contents pilot-scale sintering studies showed that sugar-based additives gave productivities that are higher than those obtained for a comparable ore blend containing haematite rather than the pisolitic ore. Several techniques of adding the sugar to the sinter mix were examined and found to increase productivity to varying degrees. Theoretical considerations, in some cases supported by experimental results, indicate that sugar-based additives not only inhibited water absorption by porous ore particles but also improved the permeability of the sintering bed. The study also suggested that, contrary to some commonly held views, the highly reactive nature of Yandi ore from Western Australia is beneficial for sintering. Porous ores enabled the formation of a strong sinter at fast flame-front speeds-both good strength and a short sintering time are requirements for high-productivity operation

Jun 18, 1905

By T. B. Colman

Paper presented at the MEP '89 conference held in Madrid, 13-15 November 1989. Britain has sustained an important metalliferous mining industry over many centuries. Recently, new geological concepts and exploration techniques have indicated that there is considerable potential for the discovery of a variety of deposit styles, often in previously neglected areas. The recent discoveries at Aberfeldy (Ba-Zn-Pb), Gairloch (Cu-Zn) and Cononish (Au-Ag)in Scotland and Curraghinalt (Au-Ag) and Lack (Au-Ag-Pb) in Northern Ireland are illustrations of this potential. Some of the prospective areas for future exploration are described and an indication is given of the legislative framework within which mineral exploration and development are carried out

Jan 1, 1991

By S. G. Beattie, N. Mojtabai

A study was carried out which aimed to: determine the effects of blasting on excavation perimeters and nearby slopes; establish a low-cost blast monitoring and field observation programme to determine peak particle velocities and blast damage; and to develop criteria for observable blast damage that are based on the peak particle velocity. Full-scale production blasts in a large open pit copper mine were monitored and studied to develop damage criteria for various rock types. Better blast designs can be achieved by correlating the results of blast monitoring with field observations of damage at the pit walls and on benches. Back-break and damage are related to blast-induced ground vibration. Peak particle velocity is accepted as a reliable measure for the prediction of ground vibration levels. Empirical models for the estimation of rock damage can be developed and used for blast design. The models are used to determine the zones of damage within the rock face. Rock damage models can also be used to design trim shots to achieve further reduction of back-break in more critical areas

Apr 1, 1996

By J. K. Whyatt, W. P. Blake, T. J. Williams

A study at the Idaho mine revealed that, despite the apparent randomness of seismic events, common characteristics defined five recurring types. These characteristics included the geological structure that slipped, the first-motion pattern and the location and intensity of damage. Many large events caused little or no damage, and where it did occur it was concentrated at intersections between slipping structures and mine openings. Of 39 events between 1989 and 1994 with local magnitudes of 2.5 or more, 10 were caused by slip on bedding planes in the southern limb of the mine, 6 occurred near the vein along a set of near-vertical faults that form the central shear zone, 8 were strike-slip events on the Southern Control Fault, 4 were by slip on the vein itself and 10 involved strike-slip and/or dip-slip movement along the North Control Fault. Strategies for control of mining-induced seismicity need to consider all five types of event, lest a strategy to reduce one type increases others

Jun 19, 1905

By J. Konnerup-Madsen, T. Unlu, H. Stendal

Paper presented at the conference Economic geology in Europe and beyond II, models for mineral deposits in sedimentary basins, held in Keyworth, UK, 13-14 April 1994. The region includes the Deveci siderite/goethite deposit and the Hasancelebi, Karakuz and Kuluncak magnetite/goethite deposits; Deveci is the only mine in operation. The area consists of a serpentine-gabbro complex overlain by a volcano-sedimentary sequence hosting the iron ores. At least three generations of hydrothermal alteration have affected all rock types except the latest trachytic dykes. The Deveci deposits occur in a pyroclastic volcano-sedimentary sequence with shales and carbonates equivalent to the main mafic sequence, whereas the other three deposits formed contemporaneously with the intrusion of trachytic dykes. The deposits are of the volcanic-exhalative type, with syngenetic siderite in pillow lavas or stratiform layers the primary and main Fe-bearing mineral. In the west hydrothermal alteration has replaced siderite in pillow lavas with magnetite or has remobilised sideritic iron into magnetite veins

Apr 1, 1995

By H. Forster, F. H. Koenemann, U. Knittel

The greenstone belt developed along the Sandawana line, an anastomosing, transcrustal shear zone. The lode gold is concentrated in veins and along brittle-ductile shear zones and other faults. Gold contents of 200 rock samples were found to be well below economically significant levels, excluding purely syngenetic deposit formation. Average gold content of unmineralised banded iron formation decreases from 7.3 ppb in the east (Manica) to 1.6 ppb in the west (Odzi), where depletion reflects hydrothermal leaching. The mineralising fluids may have been generated during deep crustal deformation, metamorphism and magmatism. Gold was hydrothermally deposited during carbonatisation and sericitisation of ultramafic and mafic rocks and during hydrothermal overprinting of banded iron formation and felsic rocks. It is present in native form and as microscopic to submicroscopic inclusions in pyrite, arsenopyrite and pyrrhotite. Argentiferous galena and other sulphides are commonly observed. Rezende, which produced over 38 t Au, is hosted by a granodiorite stock. By-product gold was produced from Cu-Ni sulphides at Mundonguara. The deposits are related to the older, but not the younger, of the granitoids intruding the belt's supracrustal sequences; the estimated age of mineralisation is 2700-2600 Ma. Odzi district, with 61 mines, has produced only 3.5 t Au as its higher-level host rocks have apparently been eroded. Mutare (formerly Umtali) district, with 133 mines and 9 placers, has produced 68 t Au (65 t from Rezende and adjacent deposits), and Manica district, with 23 mines and 8 placers, 12 t Au. Estimated reserves for the Rezende area are 20 t Au and for Manica district 4 t lode Au and 19 t placer Au

Apr 1, 1996

The Aredor mine employs conventional dragline methods to exploit alluvial diamond deposits. Production began in 1984 with the policy of mining in the terrraces during the wet season and in the river flats during the dry season. Early production failed to meet predicted grades. A major geological programme to re-evaluate existing reserves was undertaken. This resulted in considerable increases in reserves in the river flats. Many of the reserve blocks included flats on both banks of the Baoule river. Methods of access into the river flats, normally flooded in the wet season, were developed to allow mining throughout the year. River diversions have been the main method used to provide access into the reserve blocks and, most importantly, to remove the risk of flooding. Aredor has carried out six main river diversions with a total length of 12 km. The diversions allowed production planning to be made on the basis of the economic evaluation of the reserve blocks, without undue regard to natural ground conditions or to seasonal factors. The Manning equation was used for the calculation of channel dimensions and gave satisfactory results. The practical aspects of the diversion preparations and flooding prevention are described

Sep 1, 1991

By A. K. Tripathy, P. K. Pattnayak, H. S. Ray

The effects of water addition on the solid-state reaction between Cr2O3 and Na2CO3 at low temperatures (up to 873 K) were investigated to determine its possible influence on the reaction rate and the degree of conversion to soluble chromate. Experiments at high temperatures were conducted for comparison. It was found that adding water to the mixture before roasting enhanced both reaction rate and yield significantly. The reactions followed the Lesokhin-Tempelman equation at low temperature and the Ginstling-Brounshtein equation at above 973 K; the respective activation energies were 95 and 22 kJ/mol

Jun 19, 1905

By W. E. Stephens, A. J. Boyce, D. Lowry

Paper presented at Mineralisation in the Caledonides, the Mike Gallagher memorial meeting held in Edinburgh, 27-28 June 1996. An integration of S isotopic, fluid and mineralogical data for granitoid-related mineralisation showed that the porphyry systems had a predominantly subcrustal magma source, but the inner magma pulse of two-mica granite in the Fleet pluton was derived mainly from reduced sediments. The porphyry-style mineralisation formed from boiling fluids at high crustal levels, with a moderately saline fluid percolating down to the upper veins as they cooled but not penetrating the deeper Talnotry deposit. Veins in peripheral greywackes have a significant magmatic component but also incorporated CO2-rich components and metals released by dewatering of host sediments in response to granitoid intrusion. The low grade of regional metamorphism resulted in the significant fluid input from country rocks which led to the more exotic mineral compositions, especially where argillaceous sediments were involved

Jun 19, 1905

By C. A. Jeffrey

The Dirtlow Rake vein deposit, which is up to 12 m thick, contains a range of paragenetically linked replacement mineralisation styles typical of many Mississippi Valley-type deposit environments. The main ore zone lies within the solution collapse breccia domes, the more southerly of which has recently been well exposed, allowing its relationship to the associated mineral-hosting structures to be studied. The domes were largely formed during early silicification, propagated by dissolution collapse and infilled by subsequent fluorite-barite mineralisation. The location of pipes and pervasive replacement was also controlled by early silicification. Structurally controlled bow tie shears were formed as a result of fluid access at fracture-bedding plane intersections. The nature and distribution of the mineralisation styles indicate that the degree of fluid access, residence time of solutions in contact with the wallrock and susceptibility of the limestone to silicification each played a major role in dictating mineralisation

Jun 19, 1905