Search Documents

By Ramin Motamed, Fahim M. Bhuiyan, Raj V. Siddharthan, Joseph Toth

The difficulty in material characterization and the erratic response of cemented soil layers, such as caliche in the Las Vegas valley, creates challenges for practicing engineers to reliably predict the response of deep foundations. The focus of this paper is the numerical prediction of axial response in drilled shaft foundations, which are commonly used in infrastructure projects (i.e., bridges and tall buildings) in Las Vegas, NV. The prevalence of hard caliche layers with variation in the degree of cementation add to the complication in numerical modeling. In this study, the applicability of two existing t-z models, developed for Florida limestone and soft rock, was evaluated based on numerical simulations of three bi-directional load tests conducted at caliche-dominant sites. The corresponding top-down load tests were also simulated for further assessment. A MATLAB-based finite-difference program, NVShaft, has been used to implement the mentioned t-z models in axial load analysis. Complexity originating from drilled shaft construction and the interaction with caliche during one axial load test resulted in a stiffer predicted response compared to measure data. For the other two load tests, both t-z models produced comparable load-displacement responses. It was observed that the t-z model for Florida limestone predicted relatively stiffer responses and higher drilled shaft capacity.

Sep 8, 2021

By Pete Howell, Patrick Granitzki, Alicia Plinio, Janitha Batagoda

The New York City Housing Authority (NYCHA) Red Hook Houses was subjected to damage during Superstorm Sandy. As a result, the NYCHA has an ongoing project known as Restoration Associated with Sandy Recovery Program to improve the resistance against future storms. The specific project included 28 residential buildings and several service buildings within the Red Hook Development. The subsurface conditions within the eastern portion of the site included existing fill material underlain by varying stratums of very loose, loose and medium dense silty sands followed by very soft to medium stiff clay or dense silty sands. The western portion of the site included existing fill material, very loose to medium dense silty sands and organic clayey silts underlain by very soft to medium stiff sandy silts. Based on the geotechnical report, a conventional driven steel pile system was specified containing two pile depths. As part of the project bidding, an alternative pile type was recommended and analyzed to provide quicker installation, reduce vibrations, reduce noise, and provide relatively large cost savings. Due to relatively high lateral loading, an innovative double steel casing drilled displacement piles was proposed as the alternative pile option. Field testing proved the piles capable of the required project capacities and the use of drilled displacement piles as the best alternative for the project and accepted by the NYCHA.

Oct 1, 2022

By Josef K. Alter

Long-term performance and behavior of post-tensioned ground anchors subjected to axial cyclic loading constitutes an important aspect of the stability, reliability and overall performance of wind turbine deep foundations. Axial cyclic loading of post-tensioned (PT) ground anchors in soils has not been thoroughly investigated as evidenced by the research conducted for this topic. This paper evaluates research test data, available literature, and industry expert opinion on the current status and problems of deep foundation post-tensioned ground anchor (PTGA) technology, as applicable to the wind energy industry. It also introduces a proposed design solution that addresses the problems of construction cost and long-term performance of wind turbine deep foundations in soils subjected to dynamic cyclic axial loading. Deep foundations using ground anchors for wind turbines have only recently gained attention as a possible viable alternative to the mass spread footings currently in use. One of the primary problems with general acceptance of current PTGA designs is the need for long-term anchor maintenance. The research that was conducted for this study indicates that current literature only partially addresses the many factors influencing load capacity and pullout performance of ground anchors. The lack of information indicates the deep foundation industry has fallen behind in designing and implementing new technology to improve safety and performance, ensure sustainability, reduce costs, and address environmental responsibility. This paper describes the significance of this problem as it applies to the wind energy market, and proposes a new technology solution. The research, expert opinion, and analysis presented by the author is used to support the premise that ground anchor construction cost and long-term maintenance can be reduced with PTGA systems using the Con-Tech Systems (CTS) patent-pending Groutable Void Form (GVF) technology.

Jan 1, 2010

By Seth K. Martin, Tony Nichlany, Alan R. Poeppel, Konstantinos Syngros

"This paper presents a case study on bored pile construction in challenging karst conditions below a supertall building in Kuala Lumpur. Innovative design and construction techniques helped keep the project moving through very difficult and unpredictable geological and drilling conditions. The development encompasses about 12,400 square meters and includes a 77-story tower, a 59-story tower, a five-story podium, and four contiguous basement levels. The site is underlain by a residual soil derived from a siltstone/claystone (the Kenny Hill formation), then limestone bedrock. Subsurface conditions are relatively uniform within the Kenny Hill and highly variable at the limestone surface. Extreme cases included 40-meter-tall underground caverns, 40-meter-tall pinnacles, and a 50-meter-tall underground rock ledge. Local piling practice in Kuala Lumpur involves deriving pile capacity entirely in the Kenny Hill formation to avoid the unpredictable limestone surface. However, the massive tower foundation loads and relatively shallow bedrock required the piles to be socketed in the limestone. The 77-story tower will be supported by 2.0- and 2.2-meter-diameter bored piles 50 to 100+ meters long, socketed in limestone, with working loads between 40 and 70 Meganewtons. Two Osterberg-cell load tests were used to develop a site-specific rock socket skin friction correlation with RQD. Exploratory rock probes were drilled at each pile location to design the rock socket length based on the rock quality and sloping rock conditions. The rock mass was pressure-grouted during each rock probe to improve the rock quality and fill voids in the rock.INTRODUCTIONThe Kuala Lumpur City Centre, home of the Petronas Towers and the world’s deepest foundations, will be the future home of a new supertall tower. The 77-story tower will be supported by a piled-raft foundation that relies on piles terminating in the highly erratic, karstic Kuala Lumpur limestone formation. The high building loads coupled with relatively shallow limestone across the majority of the tower footprint forced the piles to extend into the limestone."

Jan 1, 2016

By Andrew Middleton, Mick Stadter, Chris Crowe, David Chong

"The Level Crossing Removal Project – Package 1 is part of the Victorian Governments commitment to remove 50 of the most dangerous and congested level crossings across Melbourne. This involved removing three crossings on the Frankston Line in the south east suburbs of Melbourne. The works involved replacing approximately 2.5km of at grade track with three rail cuttings up to 8 m deep at each of the bridges that replace the level crossings. The cuttings are retained by piled retaining walls and during the main construction occupation approximately 250,000 cubic metres of soil was removed. The project has presented significant geotechnical challenges due to the location in residential suburbs and tight rail corridor and rail occupation timeframe. These challenges included temporary and permanent wall stability, foundations, earthworks and dewatering. As a result, careful design and innovative construction techniques have been necessary to limit impacts on the community and meet the project timeline.INTRODUCTIONThe Level Crossing Removal Project – Package 1 is part of the Victorian Governments commitment to remove 50 of the most dangerous and congested level crossings across Melbourne. This involved removing three crossings on the Frankston Line where it crosses North Road in Ormond, McKinnon Road in McKinnon and Centre Road in Bentleigh.The project involved replacing approximately 2.5km of at grade track with three rail cuttings up to 8 m deep at each of the bridges that replace the level crossings. The cuttings will accommodate three lines of rail tracks with the cuttings up to 25 m wide. The cuttings are retained by piled retaining walls and during the main construction occupation approximately 250,000 cubic metres of soil has been removed.The project presented significant challenges due to the location in residential suburbs and tight rail corridor and rail occupation timeframe. As a result, careful design and innovative construction techniques have been necessary to limit impacts on the community. The geotechnical challenges generally fell into one of three areas, earthworks, structures and groundwater. The primary earthworks challenge for the project was moving the 250,000 cubic metres of soil in a 10 day window, however, from a geotechnical viewpoint, obtaining a stable subgrade on which to operate the necessary construction plant in a short time frame with constrained site access and time to import materials was the key. Whilst closely watching the performance of the dewatering system, a range of contingency plans were developed to cope with any difficulties."

Jan 1, 1900

By Giulia M. B., Ferruccio Cribari, Alessandro Bertero, Eliano Romani, Roberto Sorge, Francesca Casini

"The use of Artificial Ground Freezing (AGF) to form earth support and seepage control barrier systems has had applications worldwide. These cover a variety of construction problems, including the formation of frozen earth walls to support deep excavations, structural underpinning for foundation improvement, and temporary control of ground water in construction processes. An application of AGF during construction of Line C of Rome underground is described in detail.The new line “C” of San Giovanni metro station was constructed adjacent to the existing line “A” of San Giovanni station; the new metro line “C” is deeper than line “A” and runs below the existing station. The underpass project envisages an Artificial Ground Freezing in order to create a structural and waterproof temporary cut-off suitable to the two new tunnels excavation, while keeping trains running in the safest possible condition. The excavation of tunnels under the water table, with a hydraulic head of over 10 m in not homogeneous soils having different mechanical properties and permeability and below existing sensitive structures, involves special ground freezing sequences and methods, as well as peculiar drilling systems and operations, such as TDDT (Trevi Directional Drilling Technology).Artifical Ground Freezing IntroductionNatural freezing occurs seasonally in many areas of the globe and can affect negatively the engineering performance of geotechnical structures; on the other hand, man-made freezing is a controllable process that can be used by civil engineers to stabilise temporarily the ground in order to support and/or exclude groundwater from an excavation until the final retaining and lining structures are constructed. Freezing and thawing of the pore fluid within soils involve complex thermal, hydraulic and mechanical processes that have significant mutual interactions. For example, phase changes of the pore fluid caused by temperature variations can modify the pore water pressure in the soil, which, in turn, can induce mechanical deformation. At the same time, any changes in the hydraulic and mechanical conditions affect the thermal processes by advection and changes of ice and water contents.An application of AGF which will be presented in the paper, refers to the construction works of Line C of Rome underground. In this case AGF was carried out to provide temporary support during excavation of the two Line C running tunnels directly underneath the existing S. Giovanni station of Line A, in the safest possible condition. In order to keep the trains of Line A operational during excavation, a temporary structure was installed and a real-time monitoring system was conceived in order to control the temperatures of the soil during freezing and the response of the structures of the existing station."

Jan 1, 2016

By Vijayakumar Viramuthu, Martin Heinrich

Tower of Lot L, L1 & M, Kuala Lumpur City Centre when completed would stand 700 m tall. This Mega tall Skyscraper would merely be less than 500 m away from the world tallest Twin Tower, the Petronas Twin Tower. From June 2018 to February 2020 BAUER (MALAYSIA) SDN. BHD. constructed 225 nos bored piles with diameters of 2.0 m and 2.5 m for this tower. To comply with the depth requirement of the initial design and the need to have the pile toe 2.0 m above competent bedrock, the drilling equipment was required to be able to achieve a maximum drilling depth of 150 m. Actual piles constructed on site were deeper than 120 m. These dimensions caused superlative challenges which included but were not limited to controlling the open borehole stability over time with polymer, installing 70 t heavy steel cages and pouring up to 550 m³ concrete continuously in conjunction with installation of 88 t heavy kingposts into workable fresh concrete. The piling works were executed with one BAUER BG 48 and one BG 72, the biggest drilling rig globally available.

May 1, 2022

By Brian Wilson, Megan Atkinson, Richard Diggle, Nathan Sweeney

"Ruskin Dam, located near Mission, British Columbia, was constructed in 1929 and 1930 and comprises of a concrete gravity dam structure founded on bedrock. At the right abutment, which consists mostly of dense to very dense sands and silt, the dam abuts against overburden soils, and connects to a cutoff wall system consisting of sloping concrete slabs. Significant seepage and piping issues were encountered during first filling of the reservoir in 1930. In 2012, BC Hydro, the owner of the dam, awarded a contract for the construction of seepage control measures at the right abutment, including construction of a plastic concrete cut-off wall extending upstream of the dam, a plastic concrete seepage training wall extending downstream of the dam, tie-in of the new cutoff wall to the dam, consisting of jet grouting of the soils adjacent to the dam to allow for the construction of the special cutoff connecting the cutoff wall to the dam, and construction of additional jet-grouting ground improvement downstream of the dam.Integral to the upgrade was the requirement for the special tie-in cutoff wall, consisting of a highly flexible, impermeable membrane to connect the concrete dam to the new, 1 m thick plastic concrete cutoff wall. The tie-in extends vertically into bedrock through the dam and jet grout columns constructed adjacent and beneath the overhanging portion of the dam at the right abutment. The membrane is required to survive the anticipated earthquake induced deformation between the dam and the abutment soils.This paper describes the processes used to develop a material suitable to meet the specified flexibility and permeability criteria, as well as the innovative construction techniques utilized to construct the slot and place the bituminous material within it. The final dimensions of the slot were in the order of 7 m long by 25 m deep by 0.17 m wide. The bituminous material was placed under a head of water which was required to maintain stability of the slot, and was placed at temperatures in excess of 120 degrees Celsius."

Jan 1, 2017

By Brandon M. Robinson, Osman F. Besler, Dominik Gaechter

The Sandbukta-Moss-Såstad (SMS) project is a part of the Intercity development project, which is part of the largest transport project in Norway, consisting of 270 km of new double-track rail. The SMS project consists of 10km of double-track railway including three open stretches and two tunnels. Soil conditions consist of quick clay underlain by Bedrock. Dry soil mixing (DSM) was considered as the main soil improvement method to allow for excavation of the quick clay and construction of the D-Wall panels. The preliminary design revealed around 25,000 ton of binder installation. Therefore, a test field has been conducted to evaluate binder alternatives in means of improved soil strength by considering CO2 emissions. Multicem and Standard cement (Standard FA) have been compared for that purpose. Multicem is a type of binder which mainly consists of Portland cement and cement kiln dust (CKD). CKD is a fined-grained, solid, highly alkaline material removed from the cement kiln exhaust gases. reverse column penetration test (FOPS) and pre-drilled column penetration test (FKPS), which are common tests to evaluate DSM strength have revealed comparable strength outcome for both binder types. Therefore, Multicem has been selected as the main binder type to be used further which provided a reduction in CO2 footprint of up to 40%.

May 1, 2022

By Mario A. Terceros Herrera, Mario Terceros Arce, Antonio Marinucci

This paper describes the general principles of the expander body with post-grouting (EBI) system, and how it is similar in nature to a large-scale pressuremeter device. The results from the installation of an EBI can be used to provide information about the stress-strain characteristics of the soil adjacent to the device and to compute estimates of nominal axial resistance. As the EBI expands during grouting, pressure is applied to the in-situ soil surrounding the device thereby compacting/densifying the soil. The nominal axial resistance for small diameter piles/ground anchors can be increased due to the greater soil stiffness and shear strength around the device, larger surface and end area, and improved soil-to-EBI interaction in side resistance. The shape of the response curves depends on the geotechnical conditions of the soil (e.g., in-situ stress state, strength, and stiffness) and the installation method of the piling/ground anchor. This technique has been used successfully with different pile types and ground anchors in a wide range of conditions from very loose sands/silts to very dense sands and medium-dense gravels as well as in soft to stiff clays. This paper also describes a mini case history in which 80 piles were installed to support an office building, and the results of the static axial compression load tests performed on a production FDP+EBI pile is also included.

By Mario Mauro, Jeff Taylor, Carlos Morales

"In 2007 the US Army Corps of Engineers classified the Herbert Hoover Dike in Florida as a Dam Safety Action Classification (DSAC) 1 dam, and started the implementation of one of the largest dam rehabilitation projects in the nation. The construction of the cutoff wall is a key feature of this rehabilitation work to upgrade the dike to current dam safety criteria. The cutoff wall installation is currently being completed on Reach 1, which extends from Port Mayaca to Belle Glade, under a Multiple Task Order Contract based on performance specifications and stringent verification criteria.For the construction of the cutoff wall TREVIICOS selected the self-hardening slurry method. Since the cutoff wall is installed through a layer of highly variable limestone with Unconfined Compressive Strength (UCS) up to 14,000 psi, the excavation requires the use of the hydromill equipment. This is the first successful application of the hydromill technology with self-hardening slurry in a large scale project in the US. This paper presents the details of the method utilized, the quality control procedures, and the experience gained over seven miles of cutoff wall installed.INTRODUCTIONProject LocationThe Herbert Hoover Dike (HHD) system, around Lake Okeechobee in South Florida, consists of a series of levees, culverts and locks and is approximately 143 miles long (Figure 1).Lake Okeechobee is the second largest freshwater lake in the lower 48 states of the United States. The lake is the primary drinking water source for numerous communities around the lake and to millions of people living along the lower east coast. The lake is also a vital source of irrigation for the agricultural industry in the South Florida region.Lake Okeechobee is 33 miles wide from north to south and 30 miles wide from east to west and has a surface area of 730 square miles. The average water depth of the lake is 9 ft."

Jan 1, 2017

By Kenneth R. Chadwick, Thomas J. Tuozzolo, Terence P. Holman

"Micropiles are often installed to retrofit existing foundations that experience distortion and to underpin structures prior to future construction. The Dublin Road Pump Station project is an example of retrofitting due to a basal failure during construction that compromised the bearing capacity of the soils. A completed pump station settled and had to be restored to its original position, and work could not proceed until a new support system for the partially completed wet well could be designed and installed. The project involved the construction of three below-grade structures for a new pump station in a growing area of Jackson Township, N.J. The general contractor constructed three pump station structures consisting of a pump chamber, wet well and an inlet chamber in early 2006.The geologic conditions beneath the project site (Figure 1) consisted of loose/soft to medium dense/stiff sand, silt and clay to a depth of 40 ft below ground surface, underlain by medium dense to dense glauconitic silty fi ne sand. When the general contractor was constructing the wet well, which involved an internally supported sheet pile excavation 32 ft below the ground surface and 28 ft below the static groundwater level, basal failure, boils and ground loss occurred. Driven piles were installed to support the wet well structure, but additional ground loss was observed within and outside the sheet pile excavation, followed by settlement of the adjacent pump chamber structure. Post-failure investigations were conducted by Mueser Rutledge Consulting Engineers, N.Y. (MRCE), a geotechnical and foundation engineering consultant. Their investigation concluded that the ground losses around the pump station structures had compromised the supportive capabilities of the natural subsoils.The owner engaged Moretrench, a geotechnical specialty contractor, to work with MRCE to develop a constructible solution to support the pump station structures in general and to restore the pump chamber to its original position. Knowing that ground loss had already occurred as a function of the initial basal heave and subsequent pile driving, the team selected micropiles as the preferred foundation element, primarily due to their flexibility in bypassing these disturbed zones and generating capacity as a function of grouting volume and pressure. Drilled piles were also recommended due to concerns about causing additional settlement of the pump chamber if driven piles were used."

Jan 1, 2008

By Drew M. Kurtz, Jeff L. Rai, Sara F. Frailey, Mohammad Ayub Iqbal

"This paper presents the foundation changes made for a five-span bridge over the Lehigh River constructed as a design-build project. During excavation within the cofferdam at Pier 2 for the construction of a spread footing to bear on rock, it proved extremely difficult to control the water entering the excavation as the sheet pile tips were variable due to the bedrock pinnacles and a weathered rock zone above the top of rock allowing water to pass below the sheeting. Water also entered from the bottom of the excavation, possibly due to the presence of solution openings within the dolomite bedrock. After repeated failures to achieve subgrade elevation and maintain a dry excavation, a design change to drilled shafts was made. Additional borings were performed for each of the shaft locations to explore the area underlain by karstic dolomite rock. A seal consisting of tremie concrete with adequate weight was placed to counter the differential head of water and the three drilled shafts (with minimum 25 feet [7.62 meter] rock sockets) were installed. A detailed construction sequence was followed and advanced quality control testing was performed. The construction of Pier 2 was completed successfully.1. INTRODUCTIONThis paper presents the description of the design change made from spread footing to drilled shafts as a result of site conditions encountered during the excavation for the spread footing for a bridge pier in the Lehigh River in Allentown, Pennsylvania. The bridge is located in an area underlain with dolomite rock, presenting karstic conditions including irregular top of rock and solution openings that provided high hydraulic conductivity below the top of rock. Also, the presence of a zone of weathered rock and pinnacle rock prevented the advancement of sheet piles when constructing the cofferdam. Thus, the difficulties of advancing the excavation to the desired spread footing level resulted in the design change to drilled shafts during construction. Since the project was Design-Build, the design could be changed by a collaborative process through the efforts of the Contractor, its geotechnical and structural engineers, and the State's (owner's) geotechnical and structural engineers and construction management staff."

Jan 1, 2016

By Venkata Krishnaiah Yeddala, Sai Vivek Adari, Suresh Kumar Velugu

Assam cancer care foundation (ACCF) proposed the construction of hospitals and related facilities across 18 locations in the state of Assam-India. Tezpur is one among the 18 locations of Assam with high seismic risk. The strata at the site are comprised of mostly fine silty sands of lower SPT- N values. The water table is also encountered and ranging from 1 m to 2 m below EGL. Since the site lies in seismic zone V as per IS 1893, detailed liquefaction analysis is carried out for all five boreholes and indicates that soil is liquefiable and ground improvement is inevitable up to a depth of 15 m below existing ground level. To mitigate the liquefaction potential and enhance the seismic performance of the soil, ground improvement using stone columns by Wet top feed Vibro-replacement method is proposed. Also, the differential settlements can be avoided effectively under the raft foundation with Vibro Stone Columns. In this paper, field test validation results such as Pre and post-SPTs and ECPTs to access the extent of ground improvement, along with other information adopted in this project presented.

Nov 1, 2022

By Nino Catalano, Meeok Kim, Gordon Chen

"The design of the below grade structure of Brigham Building for the Future (BBF) included three different areas to provide power generation and medical facilities as well as a parking garage. The three areas are divided and bounded by 3 foot thick slurry walls. Because each area has different depths and functions, the excavation and construction of the below grade structure presented considerable design challenges. The intricate sequence of excavation and construction between the areas was numerically simulated using a finite element analysis to assess the behavior of the slurry wall and the retained soil. The slurry wall and the related bracing system were modeled as a linear elastic beam and truss element respectively while the soil behavior was simulated using a hardening soil model. The interaction between slurry wall and soil was facilitated by the implementation of an interface element in the numerical model. The design of bracing system to adequately support the slurry walls during the excavation was done based on the envelope of the numerical responses in stage analysis. Predicted lateral displacements of slurry walls were later compared with the field measuring data. The comparison indicated a close agreement.INTRODUCTIONBrigham Building for the Future (BBF) is located in the Brigham and Women’s Longwood medical campus of Boston. The building will serve, once completed, as a biomedical research center and clinical facility to carry out a commitment by Brigham and Women’s Hospital to be the most technologically advanced facility in the country.The 11 story building will also feature a roof garden. The below grade portion of the building has a footprint of 265 feet wide and 210 feet long and is divided into three areas, a 6 stories garage, a cogeneration plant, and an imaging center. BBF was designed and constructed to achieve LEED Gold certification and will have high efficiency and improved sustainability as a medical facility. Ground breaking was in May, 2013. Below grade construction was completed in April, 2014 and the entire building will be finished in late 2016.As shown in Figure 1, the garage area has the largest foot print, 265 feet wide and 125 feet long. The lowest floor of the garage is located about 70 feet below grade. The co-generation plant is about 190 feet wide and 85 long and 50 feet deep. The imagining center is the smallest among three areas. It is 75 feet wide and 85 feet long and 22 feet deep. The areas are separated and bounded by 3 feet thick slurry walls.The perimeter and inner slurry walls were designed to support column loads from the above grade structures, lateral soil pressures and earthquake loads as per the building’s permanent condition and requirement. However the contractor was required to design the temporary bracing and the reinforcement for the slurry walls to resist construction stage loadings."

Jan 1, 2017

By Justin Simmons, Michael Arnold, Bob Faulhaber

"In order to remodel an existing beach resort on the Gulf of Mexico, an existing three story structure, founded on stepped tapered piles, was to be replaced by a ten-story building with service rooms on a daylight basement level, conference rooms on the next levels and up-scale hotel rooms on the upper levels. The new building was founded on augered-cast-in-place (ACIP) piles. The pile caps and the basement required excavations between nine and fifteen feet (three to five meters) below ground surface.BAUER Foundations Corp. (BFC) successfully used Cutter Soil Mixing (CSM) to install the support of excavation walls. This technique allowed for the adjustment of the wall alignment during execution in order to avoid existing and new piles and other underground obstructions. Nearly 1600 – 16-inch (400 mm diameter) ACIP piles were installed to an average depth of 71.5 feet (22m) below ground surface (BGS) by BFC to support the new hotel structure. Initial grout overages in piles were excessively high and ground stability issues were encountered in some pile locations. By identifying specific areas of concern BFC was able to modify the approach to ACIP installation, effectively mitigating the ongoing risks and successfully completed the project.PROJECTMarriott Hotels began the $300 million renovation and upgrade of their Marco Island Marriott Beach Club Hotel in Marco Island, FL to JW Marriott status in May 2015. The renovation included the demolition of a portion of their existing hotel tower, and the construction of a new 10-story hotel tower consisting of 94 new guest rooms and a 10,000 SF (900 m2) ballroom, among other amenities. As is typical with hotel construction, time was of the essence. The schedule was the driving factor of this project as the owner had already booked events in their new ballroom starting in January of 2017.BFC provided the client with a deep foundation package that included the installation of 1562 Augered Cast-In-Place (ACIP) piles supporting the new tower, and the design and construction of approximately 36,500 SF (3,400 m2) of soil-mixed retaining wall for support of excavation (SoE)."

Jan 1, 2017

By Nicolas Denies, Jeroen de Leeuw, Bart Lameire, Jan Maertens, André Vervoort, Flip Hoefsloot, Noël Huybrechts, Flor De Cock

"In recent years, the Deep Mixing Method has increasingly been applied for the construction of earth and water retaining structures. From practice, it has been experienced that there is a real need to develop execution and design rules adapted to the function of the soil mix wall (retaining wall, water barrier, foundation solution or a combination) including the temporary or permanent character of the application. Based on the results of the BBRI Soil Mix project (2009-2013), a design approach has been developed in collaboration with the SBRCURnet. The present paper briefly discusses the principles of this design approach which takes into account the function of the soil mix wall and the characteristics of the soil mix material. The interaction between the soil mix material and the steel reinforcement can be considered in the calculations depending on the function of the soil mix wall. Design and quality control requirements are given in function of the application and take the lifetime of the structure into account. Durability aspects of the soil mix material are therefore considered in the present design approach.INTRODUCTIONSince several decades, the deep mixing method is used for ground improvement works. A more recent application is the use of soil mix as structural elements such as in the case of the earth-water retaining soil mix walls. Since 2000, due to the economic and environmental advantages of the method, this particular application has shown an amazing growth in Belgium and in the Netherlands. A typical excavation (16 m depth), realized with CSM (Cutter Soil Mix) panels, is shown in Fig. 1. For temporary applications, the questions related to the mechanical characteristics of the material, its permeability and its adherence with steel have been investigated with success within the framework of the BBRI Soil Mix project (2009- 2013) (see Denies et al. 2012 for more details). The durability of the soil mix material remains a complex topic while permanent applications are more and more observed in practice. In order to define an obvious design approach, it was necessary to clarify the potential functions of soil mix walls and to establish the requirements related to their design and construction. The BBRI (in Belgium) and SBRCURnet (in the Netherlands) have therefore worked together to publish guidelines in the form of a handbook titled ‘Soil Mix Walls’ (publication foreseen in 2015). In this handbook, a methodology is proposed for the design of the soil mix walls for which the interaction between steel and soil mix can possibly be taken into account dependent upon the application. Each potential function of the soil mix wall is described (e.g. earth retaining wall, cut-off wall, etc.) and the temporary or permanent character of the application is always considered."

Jan 1, 2015

By Hamed Layssi, Farid Moradi, Thomas Tingson

This paper describes the feasibility and pilot study of of using existing non-destructive testing solutions for evaluating structural integrity and mechanical performance of mass concrete foundations. This paper includes two pilot studies using well-known NDT methods (i.e., Crosshole Sonic Logging and seismic tomography) for new applications (i.e., NDT inspection of mass concrete foundations). In the first case, we will examine an existing mass concrete foundation block with internal cracking, which has negatively impacted the strength and stiffness of the foundation block. A combination of pulse velocity and 2D tomography was used to evaluate the structural integrity in the foundation block. In the second case, the quality and integrity of newly built mass foundations were evaluated using Crosshole Sonic Logging (CSL). The methods are combined to locate potential sub-surface defects such as large voids and discontinuities. This paper aims to study the effectiveness of the NDT methods of Deep Foundations to assess the quality and structural integrity of new and existing mass foundations and explore the opportunity to extend the capabilities of these tests beyond their conventional use.

Sep 8, 2021

By Chu E. Ho, Alfredas Daugiala, Nicola Ebanks

"The construction of an ancillary structure for the new Second Avenue Subway Line in Manhattan, New York City involved a deep excavation in highly variable rock conditions adjacent to a fragile masonry building. The maximum difference between the lowest and highest rock elevations was about 30 feet, which posed a problem for the installation of secant piles that formed the supporting retaining wall for the excavation. At certain areas, the rock levels were higher than the top of the invert slab of the ancillary structure. To avoid disturbance to the adjacent fragile building, the secant piles were fully cased for drilling through the overburden soils and the rock sockets were formed using non-vibratory technique. This paper discusses the design and installation details of the secant pile wall and the contingency measures that were considered to mitigate the highly variable rock conditions. Monitoring of the adjacent fragile building showed that impact of pile installation were controlled within tolerable limits and safety of the building was not compromised.INTRODUCTIONThe 96th Street Station forms part of the newly constructed Second Avenue Subway Line on the East side of Manhattan Island, New York City (Figure 1). During construction of this station, several deep excavations were carried out adjacent to existing fragile buildings (Arksman et al. 2012, Grigson et al. 2016). These fragile buildings were typically four to five stories high, with a single rubble wall basement supported on timber piles or seated directly on the fill. The timber piles were often found to be in a poor condition and connections to the footings were compromised due to rotting of the timber within the zone of water table fluctuation. Several of these fragile buildings had to be strengthened and underpinned to improve the stability of the structures prior to commencement of excavation for the new subway station box (Trabold et al. 2012, Ho and Pena-Iguaran, 2013). The situation was most challenging at Ancillary Buildings 1 and 2 located at 93rd and 97th Street respectively, where secant pile walls were located merely 2 feet away from the adjacent property line, due to architectural space constraints. While mitigation of excavation induced ground movements can be controlled by the adoption of a stiff excavation support system, a more concerning factor was the uncertainty associated with the impact of the secant pile wall installation on the stability of the existing fragile buildings. This was particularly difficult at Ancillary 1 where the secant piles encountered highly variable rock levels that intruded into the excavation space. The following sections discuss the design and installation of the secant pile wall and contingency measures that were considered at Ancillary 1."

Jan 1, 2016

By Aaron Evans, Chu E. Ho, Tom Richards

"This paper describes an innovative case history of using jet grouting to form a groundwater cutoff wall at the interface of a cut-and-cover construction and an existing tunnel. The design of the jet grouting layout was complicated by the presence of a left-in-place bulkhead of unknown dimensions abandoned by previous construction of the existing tunnel. Jet grouting was performed through predrilled holes within the narrow space between the existing bulkhead sheeting and tunnel structure. A systematic sequence of primary and secondary jet grout elements of varying diameters and panel lengths was executed to achieve an effective groundwater barrier. A key challenge in the jet grout design was the impact of potential deviations due to shadowing effects of the left-in-place bulkhead sheeting and pre-formed jet grout columns, as well as overbreak concrete in adjacent secant pile walls. The flexibility of the jet grouting methodology enabled a wide range of operational parameter combinations to be performed, allowing column diameters to be adjusted based on actual field installation measurements. Special precaution was exercised when grouting at critical locations to avoid over-pressurization and damage to the existing tunnel structure.IntroductionThe 96th Street Station box for the new Second Avenue Subway Line in Manhattan, New York included a transition tunnel, which connected the station to an existing tunnel built in the early 1970s (Figure 1). The new station and transition tunnel were both constructed using the cut-and-cover technique with bottom-up sequence (Aksman et al. 2012, Grigson et al. 2016). The main station structure incorporated permanent diaphragm walls for most of its length, except for the southern segment where high rock levels were encountered and the station box was constructed within temporary secant pile walls socketed into the rock. The permanent diaphragm walls were also utilized for temporary excavation support (Ho and Hu 2014). At the northern end of the site, the new transition tunnel was constructed within temporary secant pile walls that extended from the station diaphragm walls to the existing tunnel at the tie-in location. A temporary traffic deck spanning 60ft across the secant pile and diaphragm walls along the full excavated length of the site allowed traffic to continue operating at street level while construction of the station and transition tunnel progressed below grade."

Jan 1, 2016