Search Documents

By Jim Frazier

Tradition has often dictated low design load stresses on piles. Such traditions often developed prior to modern static or dynamic pile testing methods and perhaps result from a few limiting situations. These low stress limits were then broadly applied, even in cases where the piles could carry substantially higher loads. With sufficient testing to prove the design, higher design loads may present significant overall savings to the project owner. The cost of the testing then becomes an insignificant cost compared to the potentially great benefit of increased pile loadings. To confirm higher load possibilities for driven piles, the pile is tested either statically or dynamically. Further savings and increased testing efficiency result from remote dynamic pile testing. This paper presents a project where design stresses were considerably increased as a result of additional testing and use of remote dynamic pile testing equipment.

Jan 1, 2002

By D. S. Yang, Y. D. Wang, G. Watanabe, A. P. Notaro

"Deep soil mixing (DSM) walls reinforced with steel soldier piles were installed for excavation support and groundwater control for the construction of a grade separation structure at the intersection of Warren Avenue and the Union Pacific Railroad in Fremont, California to mitigate traffic conditions during the busy commute hours and for the extension of San Francisco Bay Area Rapid Transit (BART) system. Instead of treating the DSM wall as a temporary structure, the reinforced DSM walls were integrated in the design of the permanent structures including retaining walls, and the abutments and pier of the railroad and BART bridges. The integration of steel members inside the DSM wall as part of the permanent structures is an innovation which facilitates the use of top down construction techniques to speed construction and utilizes the steel soldier piles that would have been disregarded after the use as a temporary shoring wall. This paper will review the background of the project and DSM method and present the design and construction of the DSM wall composite structure for this grade separation project.INTRODUCTIONUsing the concept of mixed-in-place piles initiated in the 1950’s in the United States, Japanese contractors in the late 1960’s and early 1970’s installed single mixed-in-place soil-cement piles along a row to create a wall for excavation support and groundwater control. Due to the high groundwater conditions in most of the coastal cities in Japan, wall continuity and uniformity became the requirements of soil-cement walls for reliable groundwater control to minimize ground movement and impacts to adjacent buildings and facilities. In late 1970s, Seiko Kogyo, Co. Ltd. developed the Soil Mix Wall (SMW) method, which uses a triple auger mixing tool to improve the uniformity and continuity of soilcement wall. The SMW method is considered a wall installation method in contrast to the Cement Deep Mixing (CDM) method, also developed in Japan, for ground stabilization in soft soils, especially in the marine environment. In the U.S., generic terms like DMM (Deep Mixing Method), DSM (Deep Soil Mixing) or CDSM (Cement Deep Soil Mixing) are used by various government agencies and private organizations to describe the soil mixing technologies without differentiating the origin, procedure and application. The method used in this project is called DSM method by the project owner, Santa Clara Valley Transportation Authority (VTA), to produce a single continuous soil-cement wall for use as shoring wall and composite structure. The mixing tool for DSM wall installation can vary from 3 to 6 mixing augers. Due to the need to install steel soldier piles into the DSM wall for resisting lateral forces, high water cement ratio slurry with bentonite is used to produce low strength soil-cement, generally in the range of 70 to 100 psi (500 to 690 kPa), with high fluidity to facilitate the installation of steel soldier piles. To maintain the wall continuity for groundwater control, overlapping of one full DSM column is made between neighboring elements using two types of installation procedures as illustrated in Figures 1a and 1b. Steel soldier piles, as shown in Figure 2, are used to reinforce the soil-cement wall to resist the lateral shear force and bending moment induced during the excavation."

Jan 1, 2015

Jan 1, 2005

By Frederick C. Rhyner

This paper describes the design and construction of two high-capacity rock anchors to restrain a supplementary backstay for the Bear Mountain Bridge, which is a suspension bridge spanning the Hudson River about 40 miles north of New York City. The supplementary backstay was installed to relieve a portion of the tension in the southern main cable, which had been creeping in recent years. The two new rock anchors were 1,200 kip capacity each, installed at a batter to depths of 59 feet. This paper describes the subsurface investigation, group capacity analysis, installation and load testing. The rock anchors included strain gages connected to the monitoring system for the bridge. The paper describes the long term strain gage data which shows no change in stress distribution in either anchor.

Jan 1, 2010

By M. Pernot

A 12 m-deep excavation has to be perfomed in the Shanghai soft clay to install an underground electric substation. This article was originally intended to study the behaviour of the wall, the excavation bottom and the surrounding ground during the excavation. Since the works are behind schedule, and the data referring to the excavations are not, therefore, available, the article is limited to a presentation of the analysis methods that we envisaged for the study of the behaviour of the excavation.

Jan 1, 2010

By Mauricio Terceros, Martin Achmus, Freddy Lopez

The massive use of deep foundations had a remarkable influence in the building industry in the 20th century. Piles and micropiles made possible to erect thousands of civil structures around the world, changing quintessentially the urban and rural landscapes. Especially in urban areas, the ongoing development requires not only new infrastructure, but also to increase the capacity and/or to extend the serviceability of existing structures (buildings, bridges, etc.). Factors such as the change of use of existing facilities or the requirement to comply with updated building regulations confront Civil Engineers with the question, whether to tear down and build new structures, or to reinforce the existing structures from their foundations. Micropiling has enabled designers to come up with technical feasible solutions to retrofit the existing deep foundations, making the structural reinforcement a real option, even under considerable changes in the loading conditions. The following article presents an overview of an intervention project, where micropiles were designed to reinforce the original pile foundation of an existing building, enabling it to be reused with a different structural function. This paper will focus mainly on the analysis of the interaction between the existing piles and the reinforcing micropiles, especially in terms of settlements’ compatibility. Finally, the adopted solution, with its correspondent design considerations and execution process will be presented.

Jan 1, 2018

By Charles L. Guild

I will add a few facts about the use and development of the Osterberg Test Load Cell and my association with Jorj. I first met Jorj in 1965 when the Guild Construction Co. drove 12" diameter cast-in-place shell piles for him at the Marquette Cement Co. in Nashville, Tennessee. When I met Jorj at the DFI Trustee's meeting in 1985 at Longboat Key, Florida, he showed me a sketch of his idea about using a test cell at the bottom of a caisson to test the end bearing and side friction on a caisson. He had made a successful trial test in Case International's equipment yard and wondered whether a similar device could be made for a driven pile. At first I was skeptical that it could be done but after thinking about it overnight I told him I felt it was feasible and we would do some work on it. At that time, there was a large bridge job going out for bid in Rhode Island using 14" square prestressed concrete piles'. Based on a record of the Guild Construction Co. Inc. driving over 3,000,000 feet of piling on work for the State of R.I., we felt we would have an excellent chance to be allowed to use them so we designed, detailed and fabricated three for 14" square prestressed concrete piles. As things worked out, we did not test them on this job and have not to date.

Jan 1, 1989

By Brian FitzPatrick, Michael J. Weaver

Everyone has a role in site safety, even consultants. This paper presents a summary of how a geotechnical and environmental consulting firm, with field staff on construction and subsurface explorations sites, engaged their staff and leveraged relationships with contractors to assess the construction related risks to which its staff members are exposed. These findings were then integrated into their technical training materials for both new staff and those needing a refresher, so that safety is discussed at the same time as the technical work and not treated as a separate topic. The paper outlines the process of identifying and evaluating the construction related risks that staff members face and presents examples of how the consultant can engage contractors in the process. By doing this, knowledge can be shared and there is a better mutual understanding of the risks associated with common construction and exploration related field tasks. The work resulted in an increase in staff engagement in safety, a better understanding of the true risks that staff face in the field, better relationships with contractors, and lower safety metrics. HISTORY At Haley & Aldrich, Inc., we renewed our safety journey in May 2012. Like many others, we had concerns over injuries our staff experienced in the three previous years, and a potentially significant utility strike we experienced while excavating a trench. In 2009, 2010 and 2011 we experienced an increase in recordable injuries, including two significant injuries, which caused our Experience Modification Rate (EMR) (see note below), Total Recordable Incident Rate (TRIR), and Days Away-Restricted, and Transferred Rate (DART) to rise significantly. See Fig. 1 for details. This caused us to step back and review our approach to safety, and our “safety culture”. The rise in reportable incidents and injuries also corresponded to the beginning of a growth period for the company.

Jan 1, 2019

By Scott C. Vollmer

This paper seeks to examine some of the technical factors influencing the deflection of Mechanically Stabilized Earth (MSE) retaining walls based on the authors' field observation of numerous structures. Excessive deflections can be unsightly and can be perceived as wall failure. Deflections can cause cracking or gapping of the facing units and general misalignment. Deflection of the reinforced backfill zone behind the wall face can result in settlement of the backfill zone and adjacent pavement cracking. Deflections can be the result of excessive movement external or internal to the reinforced soil structure. This paper only examines internal factors affecting wall deflections. External factors such as foundation settlement are not discussed.

Jan 1, 2003

By S. Merjan

Three papers were presented for discussion at the conference: 1) Instrumented driven steel tube piles at Canary Wharf; author: A. R. Gaba, United Kingdom. The author described the Canary Wharf development in the London Docklands, and in particular, the decision to build over the water by driving open-ended steel piles 25m in length into the sands below the soft estuarine deposits. The tubes were then filled with concrete above the sand plug (usually 17m below pile head). Three trial piles were instrumented with: a) resistance strain guages on the inside of the tubes; b) vibrating wire guages on the re­inforcement of the concrete. The trial piles showed elastic behaviour in five cycles of lateral loading, while the verticle load tests showed a definite bi-linear load-settlement behaviour. The initial stiff portion was a result of frictional staff resistance, both inside and outside the tube, with the soil at the base contributing at higher settlements. Loads were taken to three times working load, with no imminent signs of failure.

Jan 1, 1991

By Bin Zhang

Drilled shafts are a popular type of foundation for transportation applications. They feature the advantages of providing high bearing capacity and generating low construction noise. Advancements in construction technology make it possible to construct drilled shaft with large diameters. In some transportation projects, the full structural loads are carried by a single large diameter drilled shaft; therefore accurately determining the bearing capacity of drilled shafts has important practical and safety implications. The increase of drilled shaft diameter combined with the structure properties of the surrounding soil play in an important role in their bearing capacity. The conventional methods for bearing capacity determination, which mostly come from experience with small diameter drilled shafts, may not work satisfactorily. This paper studies the influence of diameter on the bearing capacity of laterally loaded drilled shafts. Numerical simulations are conducted to investigate the effects of pile diameter on the lateral bearing capacity, especially the influence of shaft diameter and its structural contributions.

Jan 1, 2007

A technical exhibition was held in conjunction with the 4th DFI International Conference on Piling and Deep Foundations, Stresa. The exhibition was located in the ground floor of the Conference Hall. It was open from 15.30 on Monday April 8 till 16.30 Thursday April 11, 1991. The following is an alphabetical list of firms who took part. 1) A.P. VAN DEN BERG MACHINENFABRIEK B.V. P.O. BOX 68 8440 AB HEERENVEEN The Netherlands Tel: +31 5130 31355 Fax: +31 5130 31212 Stand Executive: A. Duyfjies

Jan 1, 1994

By H. Mori

The session chairman, Dr. H. Mori, welcomed the delegates to Discussion Session 8. AUTHORS PRESENTATIONS 1 . G. Price, Building Research Establishment. UK Mr. Price expanded on the content of his paper and presented elements of various case histories of bored piles instrumented by the Building Research Establishment. In particular, the interpretation of data from instrumented piles is critically related to: (i) the construction process (ii) concrete stiffness and variability (iii) the effects on the pile due to installing instruments The main role of the instrumentation in the examples presented was to establish pile performance under service loading conditions. Of particular interest is the mobilisation of skin friction and soil shear modulus.

Jan 1, 1991

By Paul Thurlow, Richard K. Lipscombe

The measurement of deflection of designed diaphragm walls is critical for near real time information to assess wall and soil behaviour as the internal area is excavated in a controlled manner. Data enables the site team and designers to check performance of the design, which is linked to safeguarding the site and the external stakeholders.This paper documents the use of Shape Accel Arrays at the Tottenham Court Road Western Ticket Hall during excavation and propping within the diaphragm wall for the Crossrail project. It shows how the data obtained was used within the site settlement management plan to assist in the control of the works and the information used for Value Engineering purposes that benefitted the project.The use of Shape Accel Arrays for measuring the deflection of retaining walls is not commonplace in the UK construction industry, with the Tottenham Court Road Western Ticket Hall being one of the first times they have been used in such a way. A detailed analysis of the data obtained from the instruments has been undertaken, and compared to the results obtained from the manual inclinometers that were read next to the SAAs. The advantages of the relatively new SAAs have been discussed, as well as other applications of the instrument.

Jan 1, 2017

By J. Matos e Silva

"Abstract Although one can think that it is very low the probability of a seism occurrence during the execution of an excavation in an urban lot protected by a diaphragm wall curtain, reality shows that whenever a seism occurs in an urban area several diaphragm walls will be affected by it. So it is advisable to consider the seismic action when designing a diaphragm wall curtain. The paper refers the main information about the seismic design of diaphragm walls according to the Eurocodes 7 and 8 and to the Portuguese Norms related to them (respectively NP EN 1997-1 2010 and NP EN 1998-5 2010), as the Eurocodes consider the possibility of each European country to adopt their own seismic parameters as the seismic risk is different in each country. Thus the so-called National Document of Application (in our case the Portuguese Norms) prescribes the seismic local parameters.1 - EUROCODES AND PORTUGUESE NORMS PRESCRIPTIONSAccording to Eurocode 8 - Part 5 and to the related Portuguese Norm NP EN 1998-5 2010, seismic actions on soils should be quantified adopting the Mononobe-Okabe method that gives goodapproaches when compared with reality.From paragraph 7.3.2.2 of the referred Norm, the horizontal seismic coefficient kh will be:"

Jan 1, 2014

By Reda M. Bakeer

"An approach slab is the roadway segment that immediately follows a bridge intended to provide a smooth transition between the two elements. Some approach slabs have developed rough rideability with time due to differential settlement between the roadway embankment and the bridge. Soils in south Louisiana are generally poor and highly compressible and, therefore, pile-supported approach slabs were occasionally used. Timber piles of variable lengths are driven into the soft soils where no appreciable toe support exists. This resulted in the soils both supporting loads through shaft resistance and yet experiencing long-term consolidation settlement. Field testing and review of the records of over 120 approach slabs constructed in south Louisiana yielded the conclusion that their performance is primarily governed by negative skin friction (downdrag) imposed on the relatively short timber piles. A software (TU-DRAG) was developed to evaluate the deflection profile of a pile-supported approach slab based on its geometry and conditions of the underlying soils. It evaluates the effect of dragload considering the number and spacing of the piles at each transverse row and their variable lengths along the approach slab. TU-DRAG was utilized in the design of two transportation related projects which have been in service for more than 10 years.INTRODUCTIONThe problem of differential settlement at bridge approaches or “the bump at the bridge” has been recognized for many years. Research studies (1986, 1989, 1997, 2009 and 2013) by the Transportation Research Board (TRB) and the Federal Highway Administration (FHWA) provided comprehensive evaluations of the performance of bridge approach slabs by assessing their field conditions and construction and maintenance records. Various states have also performed their own studies to investigate the performance of bridge approach slabs. The studies considered various types of structures including soil- and pile-supported approach slabs, integral bridge abutments and open-end abutments. Recommendations were provided for the design of new structures and for maintaining and repairing existing structures. Guidelines were offered regarding tolerable movements of bridges and their foundations based on measurements of vertical and horizontal movements of 580 bridges Moulton (1986). Vertical and horizontal movements greater than 102 mm (4 inches) and 51 mm (2 inches), respectively, were considered intolerable. Tolerable limits for angular distortion (differential settlement to span length) were suggested to be 1/250 and 1/200 for continuous and simple spans, respectively. It was reported that a differential settlement greater than 13 mm (0.5 inch) at the bridge interface would be sufficient to constitute a “bump” requiring mitigation."

Jan 1, 2017

By Shahriar Vandani, Andy Herlache, Andrew Bro, Wei-Yu Chen

"The Presidio Parkway Project will reconstruct approximately 1.6 miles (2.6 km) of highway, including seven new bridges, three new cut-and-cover tunnels, and a new undercrossing connecting the Golden Gate Bridge to the City of San Francisco, California. The project site is approximately 5.6 miles (9 km) from the San Andreas Fault, capable of producing magnitude 8 earthquakes. Seismic hazards include strong ground shaking, soil liquefaction, ground settlement, and lateral spreading. The Main Post Tunnels (MPT) are two parallel cut-and-cover concrete tunnels approximately 1100 feet (335 m) long. The MPT site underlain by loose sandy soils susceptible to liquefaction and lateral spreading. Excessive racking and permanent displacement due to lateral spreading are identified as the main seismic vulnerabilities. Analyses showed that without ground improvement, tunnel racking of over 5 inches (13 cm) and permanent lateral tunnel displacement of up to 15 feet (4.6 m) could be anticipated. Cement Deep Soil Mixing (CDSM) is proposed to mitigate slope displacements and increase lateral stiffness of the foundation materials to reduce tunnel racking. A series of 2-D fully dynamic time domain analyses were performed to evaluate the performance of CDSM, confirm that performance criteria are met, and optimize the CDSM geometry and replacement ratio. The use of CDSM reduced the permanent tunnel displacement from over 15 feet (4.6 m) to less than 1 inch (2.5 cm). Tunnel racking was also reduced significantly. The adopted analytical approach presented herein can be considered for future tunnel design projects in seismically active areas.Introduction The Main Post Tunnels (MPT) are an integral component of the Presidio Parkway project which will replace the existing facility with a new multi-lane roadway between the Golden Gate Bridge and the City of San Francisco. The MPT are two parallel cut-and-cover concrete tunnels approximately 1100 feet (335 m) in length. As shown on Figure 1, the project site is located in a seismically active area, about 5.6 miles (9 km) east of the San Andreas Fault and 12.5 miles (20 km) west of the Hayward Fault. The San Andreas Fault can generate magnitude 8 earthquakes while the Hayward Fault is capable of producing magnitude 7.3 earthquakes. The design Peak Bedrock Acceleration (PBA) is 0.46g for the upper level design earthquake. The project alignment is shown on Figure 2."

Jan 1, 2014

By Tracy Brettmann

The use of rock-socketed Augered Cast-In-Place (ACIP) piles is new to the Austin and central Texas region. This case history describes the design methodology, load test results, quality control procedures and the rate of production pile installation for the first large commercial project where ACIP piles were used in Austin. The piles were 24 inches in diameter and extended through about 45 ft of alluvial materials to be socketed 6 ft into limestone. A full-scale instrumented load test was performed on a test pile that was loaded to 452 tons and held for 24 hours. Telltales were installed in the middle and the tip of the test pile. As part of the overall quality control procedures, singlehole sonic integrity logging was performed on the production piles to verify structural integrity during pile installation. During pile production, an average of 14 piles per day were installed, which is approximately seven times faster than the original design that consisted of drilled shaft foundations.

Jan 1, 1998

Jan 1, 1991

By Derek Egan

"Abstract Construction clients want their foundation solutions to be right first time, every time; but it is often the geotechnical contractor who carries the most risk in achieving this. Robust validation to ensure that the installed geotechnical product is appropriate for the encountered ground conditions, will perform as required and be correctly measured for payment and record purposes is very important to minimise the contractor’s and the client’s risk. This paper outlines the development and operation of a robust real-time installation monitoring system which controls and validates the installation of driven cast in-situ (DCIS) piling. Using state of the art information technology the system allows the design engineer to interrogate the data acquired from the piling rig via his computer as the piles are completed. The use of the validation process, where data acquired during the driving of DCIS piles can be processed to estimate the finished pile performance, will be explained with reference to a new case study on large diameter DCIS piles. Examples of the routine use of the system will be presented to illustrate how automated monitoring of installation parameters can be used to raise the standard of reliability, efficiency and sustainability on piling projects. The conclusions to the paper will cover the key features and operational challenges characterising real-time monitoring of the execution of geotechnical works as developed from a number of years of experience of using a rig based data acquisition instrumentation system.INTRODUCTIONDriven Cast In-Situ (DCIS) piles have a long and successful history of use worldwide. The process, where a temporary steel drive tube, sealed at the bottom with a sacrificial base plate, is driven into the ground and filled with concrete before the tube is withdrawn, is well known (BS EN 12699, 2001 and Egan, 2013). Examples of large structures supported on DCIS piles installed by Keller UK include the Millennium Dome (now the O2 Arena) and the 2012 Olympic stadium in London.In recent times advances in piling rig instrumentation and telecommunications have enabled a new level of sophistication in the recording of installation parameters and the validation of pile performance. It is now possible to embed these features into the DCIS design and installation process which has improved the quality and efficiency of DCIS piling.This paper summarises the development and operation of a real time data acquisition and processing system for DCIS piling, but which is equally applicable to other forms of driven piling (for example concrete precast piling)."

Jan 1, 2014