Search Documents

By Tracy Brettmann

The Highway 146 Bridge Expansion Project across the Clear Creek Channel in Houston, Texas was designed on driven precast concrete piles. However, during construction, the piles along one side of the bridge along the main channel encountered obstructions and couldn’t be installed. These obstructions turned out to be the remnants of a previous bridge foundation at this location, which was unknown to the designers since that bridge had been demolished 40 years ago. Those old foundations were massive 20 ft by 40 ft (6 m by 12 m) pile caps 11 ft (3.3 m) thick supported on precast concrete piles 37 to 55 ft (11 to 17 m) long. The foundation re-design for these locations involved installing a single 78 inch (2 m) diameter drilled shaft up to 125 ft (38 m) long to replace the originally planned driven pile supported pile cap. The drilled shafts would need to be installed within very tight tolerances since they were supporting a single bridge column directly above it. In addition to drilling through the obstructions, this work would need to be completed from barges in 30 ft (9 m) of water capable of dealing with both the current and tides affecting this area. The shafts were installed using a multi-step process. The first step involved coring a larger diameter 100 inch (2.5 m) hole through the reinforced concrete pile cap and removing the concrete inside. This was followed by the installation of a 72 ft (22 m) long permanent casing to and removing the soil and existing precast piles inside. Finally, the drilled shaft excavations were advanced to the completion depths (uncased) using bentonite slurry as the support fluid.

May 1, 2022

By Mark R. Svinkin

Regulations are needed to keep construction vibrations in tolerable limits. The existing regulations were developed for low-rise residential structures, but they are incorrectly used for different super and underground structures. The existing regulations cannot prevent most of harmful vibration effects on sensitive devices, people and structures from construction and industrial vibration sources. It is important to determine the areas of application of the existing regulations and bring attention to the necessity of measurement of the structural responses for assessment of vibration effects on structures. For multi-story residential, commercial and industrial buildings, the frequency-independent safe limit of 51 mm/s (2 in./s) can be chosen for the peak particle velocity of structural, not ground, vibrations. Specifications for construction operations with dynamic sources have to consider specifics of each construction site. Preventive measures can be used to mitigate harmful vibration effects on various structures and settlements in sand and clay soils.

Jan 1, 2006

By Jorj O. Osterberg

The Osterberg (O-Cell) Method makes it possible to separate the side shear resistance (skin friction) from end bearing. The O-Cell is placed on or near the bottom of a drilled shaft and after the concrete is poured and cured, an equal upward and downward pressure is applied. From the test, the load-upward deflection curve in side shear and the load-downward deflection curve in end bearing are drawn. Typical curves are shown where the ultimate load in side-shear is reached and where the ultimate load in end bearing is reached. Several examples of tests in which the test load reached ultimate loads far in excess of what was expected are shown. The side shear in rock sockets is shown to be much larger than generally estimated. Examples are given of where side shear is smaller than expected and the reasons discussed. Disturbance of the sides of drilled holes due to poor construction techniques and ways to avoid these conditions are considered. Examples of bottom hole disturbance are given and ways to prevent the disturbance are discussed. A graph showing the actual measured capacity of drilled shafts compared to the estimated capacity as a function of the hardness and strength of the soil or rock is presented.

Jan 1, 1999

By K. Rambha Devi

The paper is an attempt to co-relate the findings of pile capacity using a number of formula suggested by various authors with the actual field load test results. Five locations consisting of wholly sandy or clayey soils were selected for this purpose. The clayey soils are on a hilly area having clays of medium to stiff consistency upto a depth of 20 m The sandy soils are near the bank of a river having angle of internal friction 'Ø' value ranging from 30 to 35 Degree. The details of the soil properties are given in Table-1 Bored cast-in-situ piles of 30 cm diameter and a length varies from 6.5 m to 13 m were designed and cast for load test to be carried out. The load applied was twice the design load. The load vs settlement curves were obtained. The theoritical values obtained by formula suggested by various authors were superimposed on the curves. From the careful study of these curves it is seen that De Ruiter and Berigen values are close to the actual results for clayey soil. For sandy soil it is found that both the BIS method and Meyerhof method found to give conservative resuslts. A multiplication factor is suggested to theoritical values for obtaining satisfactory results.

Jan 1, 1996

By J. Nakayama

For installation of round steel piles or cast-in-place pile construction through boulder contained ground or rocky formation, usual system does not function properly or impossible to work. This paper introduces an installation system which combines unique mechanism where the drill is installed on the top of a driving round steel pile or a stand pipe which is initially driven into the overburden to the depth of self-standing. When the pile driving or bore hole drilling encounters hard strata or boulder contained ground, hard material shall be crushed by the down-the-hole chiselling operated in adjustable short stroke and high frequency of blows while cuttings are discharged in reverse circulation through central reverse pipe while round steel pile is simultaneously stroked by a hydraulic hammer. The paper shall explain the mechanism of the system and introduces construction examples for bridge foundation and piled jetty.

Jan 1, 1999

By Xiong Houjin

In the excavation works of some deep foundation pits within the boundaries of Guang­dong Province of China, though some measures, such as steel sheet piles, diaphragm walls, etc. were taken to protect the walls, the construction of the excavation works was often accompanied by damage of buildings and public facilities, surface settelment. sand boil and collapse of piles. When these happened, only chemical grouting could be used as the most efficient measure for rushing to deal with or rescue the emergencies. Besides, the application of chemical grouting protection wall technique also palys a very important role under the geologic conditions of the coastal areas of Guangdong Province, when applied in the mucky oystershell layer wealthy in water and the deep mud layer, it can not only achieve good results, but also reduce the cost significantly. In this paper, we discuss the water-tight and earth retaining functions of chemical grouting protection wall in weak formation, and introduce the applicable ranges of chemical grouting protection wall in the excavation of deep foundation pits. Some technological principles and design considerations of the construction of chemical grouting protection wall are presented. Different types of protection wall are also introduced.

Jan 1, 1991

By Braja M. Das

Laboratory model test results for the ultimate uplift capacity of square and circular foundations in saturated clay (ø=0) have been presented. The results of the present model tests for square foundations have been compared with the previously published laboratory model tests results on circular foundations. Based on the comparison, it appears that the critical embedment ratio of square and circular foundations increases from about 3 for soft clays to about 7 for medium to stiff clays. By using the experimental results, an empirical procedure has been suggested for determination of the ultimate uplift capacity of belled pier foundations in saturated clay.

Jan 1, 1987

By Gray Mullins

The construction of drilled shafts as well as other cast in place foundation alternatives relies heavily on good practices from the contractor, engineer, and inspector in order to produce a quality foundation element. As many of the installation methods involve blind concreting processes, it is difficult to be certain of an intact concrete mass of the intended dimensions. A new integrity test has been developed that provides additional insight into the integrity of drilled shaft concrete. By measuring the temperature throughout the shaft via standard access tubes, the measured temperature profile can be compared to the normal signature associated with a shaft of the specified size. This article provides an overview of the new method development, test procedure, analysis, and results.

Jan 1, 2010

By Dan Brown

Two drilled shaft foundations were subjected to axial load tests in order to measure the influence of drilling fluid on performance. Other than the differing drilling fluids, the shafts were constructed with great care to ensure identical conditions. The results indicate superior performance in both side shear and base resistance of the shaft constructed using a polymer over that of the shaft constructed using bentonite drilling slurry.

Jan 1, 2002

By George Moses K, Mahendran K

Grouting is performed in rock masses in order to increase its strength properties and also to reduce the seepage. In the design of underground structures such as tunnels or caverns located in weak rock masses, grouting plays an essential role. Grouting is a complex process demanding high degree of skill and knowledge in understanding of grout flow and requirements for certain geological conditions. This paper discusses the design process for grouting in rock masses adopted for a cavern project and the practical difficulties faced during the execution at site. The design parameters of grouting includes the injection pressure, grout material properties and stopping criteria. The paper also discusses the various tests performed at site to evaluate the efficacy of the grouting process which was initially defined based on the design and previous experiences. The final grouting scheme suiting to the present geological condition is arrived based on the test results. The practical difficulties faced during the execution and the measures taken to overcome these are discussed in detail. This work shows the importance of state of art in the development of a grouting process based on geological and hydrogeological conditions prevailing at site and can be helpful in grouting design for weak rock masses.

Nov 1, 2022

By Derek J. Lennon

Ground conditions in central Glasgow generally comprise loose granular deposits overlying stiffer soils. CFA piling would normally be preferred for urban sites in these ground conditions, but flighting of the superficial deposits has on occasions resulted in building damage. Over the last five years rotary bored piling with vinyl polymer support fluid has proved to be an economic alternative to bentonite slurry. Two case histories in central Glasgow are described in this paper, one for piles founding in granular soils and one for piles founding into bedrock. A comparison is made between the methods required for disposal of the liquid waste from bentonite and vinyl polymer slurries.

Jan 1, 2006

By A. R. Gaba

Phase I of the Canary Wharf development in London's docklands involves the construction of six fifteen storey buildings located predominantly over water of the West India Docks. The buildings are supported on some 1000 No., 25m long, open ended steel tubular piles driven through 10m of dock water to found in dense sand at a depth of about 15m below dock bed level. The piles are of composite section with reinforced concrete within the upper 17m of the steel tube. Three trial piles were installed in the dock to investigate the driveability and performance of the driven steel tubular piles. The piles were subjected to dynamic and static load testing. Loads were applied in both vertical and horizontal directions. Vibrating wire strain gauges were installed on the inside of the steel piles, on the reinforcement and in the concrete to determine the relative proportions of the applied load carried by the steel tube and concrete infill and to establish how these proportions varied along the length of the piles. Inclinometers were also installed to monitor the lateral deflection of the piles. This paper describes the driving, construction and testing of the three trial piles. The results of the vertical and horizontal loading tests are discussed and comparisons are made between dynamic and static tests carried out on the piles.

Jan 1, 1989

By Minna Karstunen, Patrick Becker

"Abstract The deformation behaviour of a foundation on deep mixed columns in a natural soft soil is a three-dimensional problem, which has to be considered adequately in numerical modelling. However, simplifications are often made due to the computational costs of fully coupled 3D analyses by either modifying geometry of the problem or material parameters in 2D for plain strain analyses or by modelling the problem as 2D axisymmetric case. The volume averaging technique (VAT) is an enhanced 2D FE technique that enables mapping the 3D problem in two-dimensions, yet modelling the two constituents (column and soft soil) with appropriate different constitutive models within a homogenized material. The performance of the volume averaging technique is demonstrated by considering unit cell simulations of floating and end bearing columns in soft soil. The results with VAT are compared and validated against conventional 2D axisymmetric and fully coupled 3D finite element analyses.IntroductionThe properties of very soft clays, silts and organic soils can be improved by stabilizing agents, such as lime and/or cement that are mixed into the soil in situ by using auger-type mixing tools in situ. Deep mixed columns are extensively used to reduce deformations and to improve the overall stability of embankments and foundations on soft soils. Whilst the most typical applications are embankments, increasingly the method is used under foundations. The first category of applications is very common in Scandinavian countries, whilst the latter application has been pioneered in Poland, as an environmentally friendly (low CO2) and cost effective alternative for piling. Due to economic and environmental reasons there is an increasing interest in the technique elsewhere in Europe. With deep mixing, the strength and deformation properties of the soft soil can be improved, and the risk of unwanted deformations is substantially reduced.Numerical methods, such as finite element (FE) analysis, can be used as an alternative to conventional design methods. They are particularly suitable when considering serviceability limit state, i.e. deformation analyses under working loads. FE analyses allow using advanced constitutive models that take account of the complex stress-strain behaviour of natural soil and stabilized columns, respectively. The problems that involve a grid of circular columns under an embankment or a strip footing are fully three-dimensional problems. As 3D analyses are very laborious and expensive, an enhanced 2D technique using the so-called volume averaging technique (VAT) is utilised. The basic idea is to describe the column-improved ground as a homogenized composite material, and using clever mathematics to map the true 3D problem into 2D. Once the constitutive relations of both composites are defined, the response of the column-improved ground can be simulated in 2D subject to arbitrary loading and boundary conditions."

Jan 1, 2014

By Mario Terceros H, Bengt H. Fellenius

"ABSTRACTThe city of Santa Cruz, Bolivia, is historically dominated by houses and three to five storey buildings.The geology in and around the city is such that even very light buildings need to be supported onpiles. The recent increase of the Bolivian economy, notably that of Santa Cruz, has created a demandfor new residential as well as office and industrial buildings, which mostly consist of multi-storey orhigh-rise buildings with significantly larger foundation loads. Foundation piles have become largerand longer, and the load on individual piles is increased. The development has resulted in an increasein the demand for more sophisticated design and construction methods and stricter approach toverifying the quality of the construction processes and results.This paper describes to geology of the Santa Cruz region and how the geotechnical conditions areconsidered in the design and construction of piled foundations. The improvement of past constructionand design techniques, based mostly on bored piles constructed with bentonite slurry, is beingreplaced with new methods of constructing bored piles, e.g. the Full Displacement Pile (FDP) andincorporation of techniques such as enlarging the pile toe, e.g., with the Expander Body. This paperpresents the results of several full-scale tests and discusses the incorporation of the test results indesign and construction.1 GEOLOGY OF THE REGIONSanta Cruz de la Sierra is located in the eastern lowlands and sub-Andean zone of Bolivia, SouthAmerica. The area lies at an elevation of about +400 m and the geology is a Paleozoic (250 millionyears old) sedimentary basin. The soils of interest to civil engineering construction are quaternarywith the dominant minerals being calcite, silica and feldspar. The main agent is the Piray River and itstributaries. Their past meandering over the area has resulted in a sedimentation-erosionsedimentationprocess and a profile dominated by fine to medium sands with intermittent layers ofclay or clayey sand. With increasing distance from the river, the clay-containing layers are thicker.Fig.1.- View of Bolivia with location of Santa Cruz and map of Santa CruzThe upper about 15 to 18 m thick part of the profile consists of normally consolidated layers of clays,silts, sands, in various combination and thickness. Below, the soil is more homogeneous and consistsmostly of sand and gravel. The groundwater table lies typically at a depth of about 6 m in the highestpart of the city and at about 1 to 3 m depth in the lowest part of the city."

Jan 1, 2014

By Haijian Shi, Drew Pizzo

This article focuses on the appropriate application of subsurface investigation methods for transmission structures, which are typically designed to resist lateral rather than vertical loads. Currently, the three methods used most often for the subsurface investigation of transmission structures in the field are the Standard Penetration Test (SPT), the Cone Penetration Test (CPT), and the Flat Dilatometer Test (DMT). Each of these methods has advantages and disadvantages, and each is more applicable to some scenarios than to others. To gain a better understanding of these test methods and the implications of using them for various kinds of applications, a comparison study was conducted in the field in Maryland, for three boring locations. Each boring location was explored using each of the three tests as stated. The results of the tests and lessons learned are presented and compared, and these comparisons show that the three test methods agree on the majority of the findings. The results from each test method were also used to derive key parameters such as the soil friction angle for given foundation designs considered in order to establish a clear basis for comparison. Recommendations for performing transmission structure subsurface investigations are made in order to optimize the use of each method and thereby optimizing subsequent foundation designs. INTRODUCTION For overhead transmission structures, the most important structural requirement for determining the foundation design differs from the requirement for other structures such as buildings and bridges in accord with the conditions the transmission structures will need to withstand. In addition to the ability to bear a given vertical load consistent with its use, the foundation must bear lateral loads arising from wind and other weather conditions. The foundation types used most often for overhead transmission monopole structures include concrete drilled pier, vibratory caisson, and direct embedment. In order to determine an appropriate and even an optimum foundation design for any given set of conditions, an appropriate subsurface investigation method or approach is needed. Currently, the standard penetration test (SPT), the cone penetration test (CPT), and the flat dilatometer test (DMT) are the three most commonly used subsurface investigation methods.

Jan 1, 2018

By Susan Rafalko, Mike Walker, John Sankey, Sherif Aziz, Alex Potter-Weight, Mary Nodine, Frederic Masse

"After several successful projects on the Garden State Parkway and New Jersey Turnpike for support of single-stage MSE (Mechanically Stabilized Earth) walls using rigid inclusions (Controlled Modulus Columns) as an alternate to two-stage MSE walls and surcharge, the Bass River Bridge Widening project presented additional challenges in terms of soil conditions and height of embankment that created opportunities for the design-build ground improvement contractor and its MSE wall-designing partner to enhance their design and construction methods. The specialist contractor decided, in association with the wall system supplier, to perform an independent large scale instrumented test area on the project to demonstrate the ability of the design techniques to model the behavior of the system, as well as the capacity of the rigid inclusions to provide the necessary bearing capacity and settlement control to allow the construction of the highway without any consolidation period. This paper presents a detailed description of the design of the ground improvement system and MSE wall system, as well as the results and conclusions of the monitoring data gathered on the large scale test program. The combination of rigid inclusion ground improvement technologies, such as the CMC system, together with an MSE wall system allows for the rapid and economical construction of high embankment without waiting for a surcharge and consolidation period or the necessity to use a two-stage wall system. In-depth understanding of the design techniques and advantages of this combination will be provided and should be beneficial for any geotechnical engineer or owner looking for innovative solutions to save both time and cost on their projects.1. IntroductionAs development continues on sites with poor ground conditions throughout the world, conventional MSE walls remain a flexible design solution; however, construction of MSE walls in combination with ground improvement is becoming more frequent where extreme differential and/or total settlement prevail due to soft ground conditions. Various techniques have been used in the past in such conditions (e.g. conventional surcharge, staged construction, or two-stage MSE walls), even though these design solutions have typically involved longer waiting times for settlement to occur. As a result, conventional MSE wall design has been combined with a variety of ground improvement techniques consisting of rigid inclusions for an economical and efficient solution with the potential to accelerate construction and limit long term settlement. For the particular subject of this paper, the specialist contractor (Menard) proposed to use CMCs (Controlled Modulus Columns) to support the highest part of the MSE wall. CMCs are grouted displacement rigid inclusions installed in a grid-like pattern using a displacement auger. Before the CMCs are installed, a working platform may first need to be placed to allow equipment to move around the site depending on the ground conditions. Following the CMC ground improvement, an LTP (Load Transfer Platform) is installed prior to the construction of the MSE wall."

Jan 1, 2015

By D. A. Bruce

The Deep Mixing Method is a very valuable tool for combating problems related to in situ soil treatment, improvement, and retention. Many different variations are used throughout the world, and there is a correspondingly rich technical literature on the testing and properties of the treated soil. This paper provides a synopsis of these aspects.

Jan 1, 2001

By Ingemar Hermansson, Thomas Bjerendal, Mattias Grävare, Carl-John Grävare

"AbstractHigh strain dynamic pile tests (HSDPT) on driven piles have been carried out on a routine basis in Sweden for more than 30 years. The Swedish Commission on Pile research established, in the early 1980s, safety factors based on the percentage of piles tested. The safety factors could then be reduced, creating economic incentives for the contractor to carry out testing.Energy formulas adopted by our neighbour countries, Norway and Denmark, were not accepted in Sweden as a reliable method since the dynamic testing method was considered to be a more scientific and reliable method. It has become almost the only in-situ method used to verify geotechnical bearing capacity on driven piles.The typical Swedish geology of soft soils overlaying very hard strata makes it possible to verify high design loads, typically 20 kN per cm2 of pile cross sectional area for steel piles and 1,5 kN per cm2 for concrete piles.Conventionally a certain percentage of the piles have been tested in Sweden. The EC7, on the other hand states a number of piles to be tested, regardless of the total number of piles. The Swedish NA (National Annex) states a maximum distance between tested piles, which results in better distribution of the test piles over the foundation.For shaft-bearing piles in soft clays, dynamic pile tests have to be correlated by static load tests.Historical backgroundOn a research basis stress-wave measurements have been carried out for a long time in Sweden. One example is a project in the city of Gothenburg, conducted by Fellenius and Pejrud (1964). Strain gauges were glued on the reinforcement bars in 60 m long, precast concrete piles at 3 m and 25 m above the pile tip respectively. Evaluation was done with different methods such as dynamic formulas,stress-wave measurements and in addition compared with static load tests.In the 1975 Building Code in Sweden, driving criteria for concrete piles based on stress-wave theory were introduced, as summarized in Table 1. The driving criteria are intended for 3 and 4 tonne gravity hammers. For hydraulic rigs, which have free-falling hammers, the drop height indicated should be reduced to 80 % of the values in the table. The criteria were considered to include a safety factor of 3,0. For 330 - 450 kN pile load, pile with a standard a cross sectional area of 235 mm x 235 mm was used. For 600 kN load, the standard cross sectional area was 275 mm x 275 mm."

Jan 1, 2014

By Erik M. Westerberg

The Soilex Pile combines a slender shaft, for quick and easy installation, with an enlarged pile toe, for high capacity. The key component is the Expander Body, which is inflated by injecting cement grout when in position. The latest development in the Soilex Pile System results in a reduction of the total cost of Soilex Piles, in many cases values that are competitive with pre­cast concrete piles and displacement piles. Soilex Piles can now be installed on top of a bearing soil layer, instead of 3 to 4 m into that soil as previously required, further minimising the ground disturbance. Soilex Piles achieve high capacity in relatively loose soils, with ultimate loads typically between 1000 and 2000 kN in a sand with CPT qc = 5 to 10 MPa or SPT N= 10 to 20. It is possible to pre-load and proof-load all piles with dynamic testing up to 2000 kN or using built-in jacks, thereby verifying the capacity. The vibratory installation method, which is extremely quick and causes very little soil disturbance and noise, is exemplified by two case histories.

Jan 1, 2000

By Sridhar Krishnan

This paper presents the results of a comprehensive pre-production pile testing programme for the US$ 800 million 1400MW Coal-Fired Jimah Power Plant Project in Negeri Sembilan, Malaysia. The testing programme included high-strain dynamic testing and fully instrumented static axial and lateral load testing of driven prestressed concrete piles and bored cast-in-place piles. A highlight of the testing programme was the pioneering use of the Global Strain Extensometer (GloStrExt) Method, a deformation monitoring system that uses advanced pneumatically- or hydraulically-anchored extensometers and a novel analytical technique to monitor loads and displacements down the shaft and at the toe of driven prestressed concrete piles. The experience with the testing programme for the Jimah Project also demonstrates the possibility of achieving notable breakthroughs, not only in the monitoring, evaluation and reporting of pile foundation behaviour dynamics but also in our understanding of the mechanisms that underpin such behaviour. These significant gains are undeniably a direct result of the committed and co-operative relationship among the project owner, design/builder, specialist piling subcontractors, pile suppliers and pile instrumentation and testing specialists.

Jan 1, 2006