Search Documents

By Carnevale Francesco, Bracci Laudiero Alberto, Pampanin Piero

"SummaryIn the Port of Naples a slurry wall has been realized through a sandy layer up to a deep tuff layer using the Cutting Soil Mixing technique.The executed panels have dimensions of 2.8 m x0.65 m in plan and a total length of 25 m. Primary and secondary panels have been executed using the wet to wet technique. During the panels execution the following parameters had been measured: injection pressure, injected volume, verticality. At the end of the works an exploratory campaign has been carried out through boreholes collecting samples for laboratory tests in order to verify the diaphragm thickness and its physical and mechanical properties (i.e. unit weight, unconfined compressive strength).The interpretation of the collected data allowed to verify the efficiency of the method, the volume of slurry loss due to permeation during the panels execution, the quantity of the obtained spoil compared to the volume balance equation, both for the sand and the tuff layer.Eventually, the measured physical and mechanical characteristics of the panels have been correlated to the execution method performed.IntroductionIn the Naples Port area there is a polluted site which has to be hydraulically isolated in order to prevent the pollution of the groundwater that flows from land to the sea through the Port area. A hydraulic cut-off wall has to be realized and particularly a slurry-wall realized using the CSM method had been executed.To date, two stretches have been executed, 140 an 110 m in length respectively, as shown in Figure 1 and Figure 2.After execution, the slurry-walls have been investigated with boreholes. In-situ and laboratory tests on the recovered samples of grout have been carried out; furthermore, the geotechnical parameters of the mix composing the wall have been measured."

Jan 1, 2014

By A. Mazzucato

This paper presents the experimental results of driving and load tests on an instrumented pile driven into a test pit filled with fine homogeneous sand.

Jan 1, 2010

By Mary C. Nodine, Michael P. Walker, Paul Eggers, Donald E. Aubrecht

The CANALSIDE commercial development in Buffalo, New York serves to revitalize the former site of the Buffalo Memorial Auditorium, adjacent to Lake Erie. The Auditorium was constructed in 1940 and founded on steel H-piles driven to limestone bedrock. After decades of professional sport and entertainment events, the “Aud,” as it was locally known, was closed in 1996. It sat vacant until it was demolished in 2009, at which time plans were made to revitalize the area with shops, restaurants, and a historic replica canal. The only portion of the Aud that was left intact was a subbasement boiler room. The subbasement was renovated in 2014 and has since been used to house water and ice making equipment for the historic replica canals, which boast recreational ice skating in the winter. The subbasement floor was about 10 feet below groundwater and the Lake Erie water level. The floor consisted of an approximately 4-foot-thick layered inverted waffle slab system, with reinforced concrete grade beams and concrete infill between the grade beams. A waterproofing membrane was located near the base of the slab. There were no major seepage issues in the subbasement, so the existing waterproofing membrane was assumed to be intact and performing adequately. A four-story building housing a children’s museum was proposed to be constructed directly above the subbasement. The loads imparted by the new building would exceed the capacity of the existing piles, so it was determined that drilling micropiles through the subbasement floor would be the most practical means of supporting the new building. Drilling through the existing slab and waterproofing system was a concern due to the challenges of controlling water during construction and the importance of maintaining the integrity of the permanent waterproofing system.

Jan 1, 2018

By D. G. Bishop

This paper is intended as a review and update of the use of Pressure Injected Footings as deep foundation units in North America. We will discuss various aspects of this pile and then discuss a particular project - the Mobile Alabama Convention Centre which is currently under construction. Pressure Injected Footing is a generic name used to describe a foundation unit that has been in use around the world for some 80 years. It has been used on all types of structures. It is an excellent pile in both compression and tension. It is particularly economic where a layer of granular soils can be found at relatively shallow depths. Other types of piles would penetrate these layers. Caissons are often difficult to construct in these soils because of their lack of cohesion and the often present water table. PIFs can density these shallow layers and carry relatively heavy building loads on them.

Jan 1, 1992

By Koichi Kobayashi

Performance-based approach to design of structures including foundations was adopted after enforcement of the revised Building Standard Law in Japan in 2000. The use of piled-raft foundation is favorable for medium-rise buildings in soft ground because of its good performance. In the design of the piled-raft foundation (Architectural Institute of JAPAN2002), vertical load is usually carried by the raft foundation, while the pile is primarily meant to control settlement of the structure. Shaft friction is expected to be larger in a nodular pile(Karkee, et.al., 1998) since it has larger surface area than a straight pile, and such piles are frequently used in piled-raft foundations. Since few structures with piled-raft foundation exist currently, the settlement characteristics of piled-raft foundation have not been fully clarified. To design piled-raft foundations with better confidence, the mechanism of vertical bearing capacity and the spatial distribution of settlement should be clarified, for which the actual behavior of the building-foundation system needs to be evaluated. This paper presents observations of settlement of a building with a piled-raft foundation at a soft ground site. The building is a steel structure covering an area an 766 m2, and consists of two-storey office block and one-storey warehouse block. The filled ground of about 5-m thickness at the ground surface is underlain by approximately 4-m thick alluvial sand layer below which lies about a 17-m thick alluvial clay layer with SPT N-value less than 2. The piles used in the piled-raft foundation are 12-m long nodular piles with nodal diameter of 500 mm (pile shaft diameter is 400 mm). The bored pre-cast piling method (Karkee, et.al., 1998) was used to install the piles. To evaluate the foundation settlement, the method of analysis of three-dimensional frame system, utilized widely in Japan, was adopted in combination with the foundation system. Basic assumptions were: (i) total ground settlement is evaluated as the sum of immediate settlement and consolidation settlement, (ii) immediate settlement is evaluated from the Mindlin?s solution in which strain dependency of shear modulus of soil is considered, (iii) settlement in clayey layers is evaluated by the one-dimensional consolidation theory, and (iv) shear spring between soil and pile shaft is represented by a hyperbolic function. The applicability of the method of analysis was verified by comparison with results of field monitoring of building settlement.

Jan 1, 2006

By Nabil F. Ismael

The axial capacity of step tapered bored piles in sand was examined by field tests at one site in Kuwait. Two straight piles, and two step tapered piles were load tested in compression to failure. All four piles were 3 m deep. The straight piles were 0.2 m in diameter. The step tapered piles had a diameter of 0.3 m for the upper segment which extended up to 40% of the pile length changing to 0.2 m diameter for the lower section. The soil profile consists of medium to dense sand with minor cementation and no groundwater was encountered. Both the ultimate bearing capacity and the settlement at working loads were examined. The axial capacity of the step tapered piles was greater, and the settlement at working loads was less, compared with the straight shaft piles. The increase in capacity is mainly attributed to the added side friction along the larger diameter top segment of the shaft.

Jan 1, 2008

By Walter G. Kutschke

Four significant soil nail wall projects in the eastern United States were recently completed with a combined area of 175,000 square feet of finished shotcrete surface. These projects required the use of innovative design and construction methods in order to address various challenges, including slide-prone back slope materials, perched water, highly erodible rock materials, curved wall alignments, very tight construction tolerances and unexpected subsurface conditions. Special focus is given to issues such as bench excavation, soil nail installation methods, shotcrete mix design, anticipated shotcrete quantities, shotcrete nozzlemen qualifications and weather conditions, in order to provide a lessons-learned database for future soil nail wall design and inspector considerations. These projects also underscore the importance of design engineer and soil nail wall contractor qualifications as well as effective communication with the owner.

Jan 1, 2007

By Scott White, Pishun Tantivangphaisal, Andrew Bell, Chris Barker

There has been considerable advancement in recent years in the tools, both software and hardware, available to allow efficient digitalization of site records during the construction of geotechnical works. Whilst these tools have excelled at replacing handwritten records, the ability to use digital records to validate design and construction requirements in real time or even within reasonable timescales has generally been limited to the development of bespoke ‘prototype’ project specific solutions. This paper describes the development and implementation of an industry standard design schedule and the benefits of the broad adoption of a single database schema for data recorded on geotechnical sites. The former has brought significant improvements and automation of the design process, whilst the latter has enabled the validation of the constructed works against design intent in almost real time. Further details of the standardized design schedule, already publicly available in the UK through the FPS, examples and lessons learnt from implementing digital site record systems on live projects are presented herein. The utilization of cloud computing technology and complex algorithms linking plant/rig instrumentation with design data can further automate construction sites using IoT (Internet of Things) best practices. The authors will share their experience of the recent deployment of a digitalized design-to-construction record system, give recommendations for future development and a call for an industry wide drive to finalize and adopt the AGS Piling data schema.

May 1, 2022

By Z. G. Lin

In Xian, China, compaction by means of soil (or lime-soil) piles is one of the effective methods widely used for densifying loess and eliminating its collapsibility. However, as a result of groundwater table rising, it is no longer applicable in many areas. This paper is the summary of the first-time use in Xian of sand-gravel compaction piles aimed at densifying the miscellaneous fill (already partially under water) and saturated loess at a certain project site. In-situ tests, conducted before and after the treatment and including several kinds of penetration tests backed up and confirmed by a set of plate loading tests, yielded very satisfactory results, strongly testifying to the viability of the method.

Jan 1, 2010

By Boleslaw A. Klosinski

Drilling of a pier hole is accompanied with stress releasing in the surrounding soil and often with loosening of soil at the pier base. In effect the drilled piers are more deformable than driven piles of comparable dimension. The bearing performance of a pier may be considerably improved by properly executed base grouting. Various techniques of base grouting are used; many of them were described by Bruce (1986). The grouting devices are often placed within the pier. Alternatively the soil at or under the base is treated by cement or chemical grout. Preloading of the base subsoil by use of a special grouting cell is considered as the most effective way. Treatment of the ground below pier base with cement or chemical grout may be also useful. It may be performed immediately after the pier construction or during service, as a measure for increasing the pier capacity.

Jan 1, 1995

By B. M. Das

Laboratory model test results for the ultimate uplift capacity of rough rigid single and group piles embedded in sand have been presented. Model tests on single piles were conducted in loose, medium, and dense sand. The uplift tests on group piles were conducted in medium sand only. Based on the present model test results, tentative relationships for the estimation of the ultimate uplift capacity of single pile have been presented. The efficiency of group piles is a function of the length-to-diameter ratio, center-to-center spacing to diameter ratio, number of piles in a group, and the degree of compaction of sand.

Jan 1, 1989

By Timothy C. Siegel

In response to a solicitation for ground improvement for the construction of a new hospital in Owensboro, Kentucky, the team of Berkel & Company Contractors and Dan Brown and Associates PC designed and installed lightly reinforced cast-in-place piles (known commercially as Cast-in place Ground improvement Elements or CGEs) as part of a composite ground system. The concept of the design is that the structure load is shared between the piles and the soil subgrade. The load sharing is controlled (to some degree) by the placement of a cushion between the pile head and the bottom of the overlying spread foundation. In an effort to confirm the design principles and to better understand the behavior of composite ground, the design-build team performed plate load tests on ground with a single CGE and with a group of CGEs. The small plate test (on ground with a single CGE) characterized the stiffness of the cushion. The large plate tests showed that the cushion will distribute the applied load to the CGEs and to the soil subgrade between the CGEs. On the basis of the plate tests, it was concluded that the plate stiffness can influence the test results. The use of a concrete layer was effective at supplementing the plate stiffness. The cushion was shown to be an important component of a composite ground system by allowing mobilization of the soil subgrade resistance and avoiding a stress concentration at the tops of the CGEs that would otherwise be present if the spread foundation and piles were rigidly connected. Because the composite ground system engages the resistance of the soil subgrade, the structural demand is reduced and consequently there is a potential for savings when compared to a conventional pile foundation. Several foundations for the new Owensboro hospital are being monitored for vertical movement during construction of the superstructure that will extend through 2011. At the time of this paper (mid 2011) the settlement of the foundations due to only part of the structural load (primarily the structural steel) has been negligible.

Jan 1, 2011

By William S. Gardner

It is certainly an honor to have been invited to address the Deep Foundation's Annual Meeting on such a vast and weighty topic as "Present to Future Design Considerations of Deep Foundations." Acknowledging the enormity of this 30-minute assignment, I hope to at least scratch the surface of the topic deep enough to generate some thought and reflection. Design considerations, be they current or future, bring to mind a number of important subtopics which comprise the design process. As shown by Figure 1, a flow chart of this process describes, in general terms, the sequence of a deep foundation design.

Jan 1, 1991

By K. Viking

This article deals with some of the civil engineering related problems to be encountered when offshore wind energy projects transform from prototype offshore wind energy converter farms, developed and installed during the 1990's, to commercial farms that's currently planned to be built. The offshore wind energy converter (OWEC) installations encounter a wide range of problems, only partial of these are geotechnical. In Europe both onshore and offshore wind farms have, from a historical point of view, usually been founded by using the monopole technique, installed with traditional impact hammers, or by using gravitational foundations. However, the rapid development of bigger turbines and larger wind farms, together with increasing considerations of fatigue aspects, has lead to financial benefits of developing and exploring other foundation techniques. This paper reviews some Scandinavian experiences regarding critical components of the design phase in relation to connecting the superstructure to the ground, and some of the main considerations of how the loads applied to the structure are transferred to the surrounding soil. Keywords: Offshore Wind Turbines, Wind Farms, Foundation, Pile, Gravity Structures

Jan 1, 2005

By Joseph A. Sopko

There has been a trend in recent years in performing the initial formation freezing using liquid nitrogen (LIN) and then converting the system to circulating refrigerated brine. While proponents of this method state it decreases freezing time, it can also be considered an alternative to inadequate refrigeration capacity. This method was used on several small projects in the 1980s. Problems such as broken pipes, frozen brine, and unsafe work conditions caused contractors to re-think the method. This paper discusses these problems and also presents work schedules showing no schedule reduction. In fact, this method can lead to longer time as well as significantly higher costs. BACKGROUND Ground freezing as a method to provide groundwater control and temporary earth support for excavations is completed using a relatively simple process: drilling and installing refrigeration pipes around the perimeter of the excavation and introducing a coolant into these pipes. The coolant extracts heat from the ground, converting the pore water to ice and forming a strong, impermeable material. A typical ground freezing system is illustrated in Fig. 1. SYSTEMS There are two basic types of coolant systems: circulating and direct expansion. The circulating coolant system is made of two separate, closed systems. The medium circulating is the secondary coolant. It is cooled at a central refrigeration plant, circulated through the pipes, and warms as it extracts heat from the ground. It then circulates back to the plant where it is cooled. This coolant is chilled in a heat exchanger by the primary refrigeration system where a compressor system is charged with a refrigeration gas. The heat is ultimately extracted from the ground and expelled into the atmosphere by an evaporative condenser. Secondary coolants are usually a brine or glycol chemical while the primary refrigeration gas is anhydrous ammonia or another commercially available gas.

Jan 1, 2019

By K. [Muthukkumaran

An extensive program of laboratory model tests was undertaken to study the effect of slope on p-y curves under passive loading in dry sand. The paper concerns the method developed in a series of laboratory model tests to experimentally determine p-y curves. Bending moment curves are differentiated by using curve fitting method of cubic polynomial function. The study includes effect of slope angle and relative density on bending moment and non-dimensional p-y curves. The non-dimensional p-y curves for piles on sloping ground under passive load are developed modifying API method by including a Reduction Factor (R) using the experimental results.

Jan 1, 2006

By Scott D. Thomson

The client for this project specializes in the use of state-of-the-art technology to fabricate and assemble composites and metal-bonded structures for commercial and military aircraft programs. One of the key components for this operation at the client's plant is a highly precise computer-numerical-controlled router known as the Shoda Machine. This machine tool was installed at the plant in July 1998 for the manufacture and inspection of aircraft parts, and it is extremely sensitive to deflections. To monitor the occurrence of deflections, an internal laser system continuously checks the machine calibration. Deflections in excess of 5/1000-inch in the foundation on which the machine rests require costly periodic re-leveling and recalibration of this tool. Therefore, a significant problem arose when measured deflections during machine operation were as large as 20/1000-inch. In addition, the foundation was cracked in at least three places as a result of elastic foundation movement caused by dynamic loading as well as shrinkage and loss of base support. Deciding on a remediation procedure to alleviate or eliminate these problems involved the following important considerations: (1) achieving the client's need for reducing deflections to less than 5/1000-inch, (2) minimizing the repair cost as much as possible, and (3) reducing the time required for implementation of the foundation remediation solution. After evaluating the advantages and disadvantages of several alternatives, jet grouting was selected as the most suitable solution. The jet grouting program provided columnar elements of soilcrete to remediate the Shoda Machine foundation.

Jan 1, 2003

By Nagarajkumar BV

Pavai-and TeampT JV started working on the project T49A, Sumbar J & K State as part of slope and earth stabilization for ongoing Banihal - Katra Railway Connection Project. This project has several tunnels and bridges with slopes that are protected with various types of protection system such rock bolting, rock anchors, and micro piles. For the main two bridges Bring number 2 and 3 at T49 A location Pavai - TeampT JV has to design and execute the circular group of micro piles (Fig.1) for deep excavation of earth for the purpose of construction of well foundations (CAISSON FOUNDATIONS) for both bridge 2 and 3 piers. In this paper we discuss about the purpose, basic design, detailed design approaches and actual work implementation of micro pile with composite rock bolt applications and permanent rock anchors for slope stabilization works in this project.

Nov 1, 2022

By Douglas C. Brunot

Mabey Inc. is providing for the shoring design for the Naples bay Center project, located in Naples, FL. The excavation is approximately 374' long by 164' wide and is 27'-8" deep at the shoring line with a groundwater level six feet below present grade. The project Excavation is for a multi-use facility for residential and retail with underground parking. The shoring design will be incorporated into the foundation walls for the building. Mabey is using its pre-engineered Super Powerbrace Plus (SPP) wales and Mega Struts to support the excavation in two phases. The system design and the design of all the pre-engineered components are by Mabey. The foundation is supported on drilled shafts arranged with the building column grid. The excavation will be completed in two phases to allow for equipment mobilization and operation on a site with limited access. The construction sequence will begin with placement of the drilled shafts. The drilled shafts will also serve as the building columns. After the drilled shafts have cured, 630 AZ24-700 x 45 ft. long sheet piles will be installed. The sheets will be arranged in two phases, divided by a center row of piles. Since de-watering in south Florida is very expensive and often downright impossible prior to placing the seal slab, all the initial foundation and excavation bracing work will be completed with groundwater in situ. The entire excavation will be excavated to 5 ft. below ground surface to allow for the installation of the wale support brackets at 12 ft. on center, welded to the sheet piles. After the support brackets are installed, the SPP hydraulic wales and the Mega Strut hydraulic braces may be installed for both phases. Once the frames and struts are in place, Phase 1 excavation is completed, followed by Phase 2 excavation. The 4-ft. thick seal slab is then placed and cured in the wet. De-watering is now possible with the seal slab in place. Once the excavation is de-watered the leveling slab is placed and cured. The center row of sheet piles is then cut off at the top of leveling slab. With the leveling slab cured, the sheet piles have enough strength to support the excavation without the frames and struts near the ground surface. The permanent sheet piles are then seal welded for water proofing and the foundation walls are cast with the sheet piles. The design is modelled in 3D using REVIT to ensure accuracy of the design. The earth pressures are developed using Coulomb theory as there is a top frame and the frame and sheet pile are flexible and move to develop an active pressure wedge. Earth pressure uniform loads and loads from predicted surcharge are modeled in STAAD to determine load effects on the SPP frames and Mega Struts. Coulomb theory and Mabey’s structural model will be tested through monitoring with Mabey’s LIVEPin system. LIVEPin will be placed in struts for each phase of construction. The LIVEPin results will be calibrated with the structural model to determine actual frames forces and will also determine the actual earth pressures applied to the system from surrounding soil. Mabey has used the LIVEPin system in similar applications and this has helped us determine modelling accuracy.

Jan 1, 2018

By Bernard Hertlein, Chia K. Tan

"The move to LRFD methods for structural design by AASHTO, ACI, AISC , ASCE, and the FHWA has been a major change for the American construction industry. The deep foundations industry has arguably been placed most at risk by this situation, because of the need for, and the difficulty of providing, reliable quality assurance.LRFD is attractive for both the owner and the engineer because it promises cost reductions, but the assumption underlying LRFD is often overlooked - that the acceptable margin of safety can be rationally reduced, thus saving costs, provided that all the factors involved are closely controlled. This means that both the quality of the materials and the quality of the construction work must be closely monitored, and held to an acceptable standard.This paper describes the type of comprehensive quality management program that is needed in deep foundation construction projects based on LRFD. Case histories are used to illustrate the importance of both adequate inspection and reliable testing to a comprehensive quality management program.IntroductionOver the last thirty years, the major organizations that set standards and practice policies for the American construction industry, such as the American Association of State Highway and Transportation officials (AASHTO), the American Concrete Institute (ACI) , The American Institute for Steel Construction (AISC), the American Society of Civil Engineers (ASCE), and the Federal Highway Administration (FHWA), have embraced Load and Resistance Factor Design (LRFD) as an alternative to, and in some cases, a complete replacement for, Allowable Stress Design (ASD). AASHTO first published a new set of LRFD-based design guidelines for bridges in 1996, with several revisions in 1997, 1998, and 1999 (AASHTO, 1996). The 1996 AASHTO Bridge Design Code was the first in the United States that required foundations to be designed using LRFD procedures. LRFD has a clear advantage over conventional ASD where variability in material strength, bias in design methodology, and degree of construction quality can be rationally accounted for to achieve an acceptable level of risk."

Jan 1, 2005