Search Documents

By George Mylonakis

The curvatures and subsequent bending imposed to piles by the surrounding soil during the passage of strong seismic waves is studied. This type of bending develops even in the absence of a superstructure and is referred to as "kinematic bending", to distinguish it from bending imposed to piles by loads generated from the inertia of the superstructure ("inertial bending"). Although kinematic loading may be severe in the presence of sharp stiffness discontinuities in the profile and may lead to damage, it has received little attention by engineers. The scope of the paper is twofold: (i) to discuss some fundamental aspects of seismic pile bending, and (ii) to review some existing design methods. To this end, a dimensionless bending strain parameter (instead of the more commonly used bending moment), and a strain transmissibility function relating pile bending strain and corresponding soil shear strain are introduced. Numerical examples are also presented.

Jan 1, 2002

By Thomas M. Gurtowski

This paper presents a summary of allowable bearing pressures and skin friction values that have been used to design drilled pier foundations for support of high-rise structures in downtown Seattle, Washington. These design parameters are based upon a review of geotechnical reports and records of more than 20 building projects. The following pages present a description of the soils encountered at these sites including foundation bearings soils, and design bearing and friction values. The accumulated data is summarized in Table 1, and the locations of the buildings are shown in Figure 1. A detailed description of the construction of two belled drilled piers are presented illustrating typical methods and procedures used in downtown Seattle. The two cases are from the Washington State Convention and Trade Center (WSC&TC). SEATTLE AREA SOILS The Puget Sound area was subjected to several major glaciations during the Pleistocene Epoch. Glacial ice originated in the cordilleran and coastal mountains and the Vancouver Range of British Columbia. The maximum southward advance of ice reached the area about halfway between Olympia and Centralia. As a result of these glaciations, the Puget Lowland was filled to significant depths by glacial and non-glacial sediments during the Pleistocene.

Jan 1, 1990

By Robb L. Swenson

Construction of foundations for the Skyway Segment of the San Francisco Oakland Bay Bridge required innovative techniques due to the mass of the structures being inserted and the unique subsurface of the Bay. Twenty of the pier structures required large sheet pile cofferdams. Eight other foundations were installed in open water without cofferdams at the deeper part of the Bay. This narrative will present the initial planning, as well as the stages of installation, for each type of foundation. The first section will discuss foundation constructability modifications made during the initial planning phases of the project. Considerable effort was expended by Caltrans, the owner, T.Y. Lin the designer, and KFM (Kiewit/FCI/Manson) the contractor in modifying the design to assure that required tolerance would be maintained during the installation of the foundations. The final section will describe the steps required for installation including: initial access dredging, installation of cofferdams, preparation required to install the footing boxes, footing box installation, foundation support pile installation, and pile to box connections.

Jan 1, 2005

? Hollow Stem Auger ? Drill Bits ? Leads/Torque Arm ? Hydraulic Gearbox ? Hydraulic Power Unit ? Grout Pump ? Crawler Crane

Jan 1, 1997

By Bengt H. Fellenius

The bearing capacity equation?"the triple N formula"? is now about 50 years old. It was developed from theory of plastic resistance of metal to a cone being pressed into the surface of the metal, superpositioned by resistance due to shear in an interparticulate medium (soil; note, we are not dealing with metallurgy), and tempered by work necessary to move the footing into the medium. The equation (and its coefficients) was "confirmed" by tests on small footings placed at or near the surface of the soil. The equation is a basic tenet of every geotechnical textbook, manual, and code. Over the years, innumerable variations of the N-coefficients and adjustments to the equation have been published. The main assumption behind the bearing capacity equation is that a shear plane develops between two essentially otherwise unaffected bodies: the main soil body and a body comprised of the footing with some soil. Moreover, the notion is that a model footing placed at or near the surface of a soil would behave proportionally or similarly to a full-scale footing, or to even a same size footing (pile toe) placed at some depth in the ground. This is not in agreement with factual observations. It is suggested that the behavior of a small or large diameter footing as well as a pile toe is governed by compression of the soil below the footing or pile toe and not by "bearing capacity".

Jan 1, 1999

By Alexander J. Verstraeten

The design and construction of foundations for power transmission line towers present some special problems. This paper describes a system of design and construction for these foundations that was developed in Europe and has attained general use there because of its reliability and cost effectiveness. Transmission line foundations distinguish themselves by having to deal not only with compressive and lateral loads, but with uplift loads and, because of the wind (in some regions earthquakes), with dynamic loading. The construction of transmission line foundations distinguishes itself mainly in the great number of inaccesible locations involved, resulting in extensive geotechnical investigation and logistical problems in moving men, materials and equipment.

Jan 1, 1987

By Karl A. H iggins, James P. Racine

"Displacement Cast-in-Place (DCIP) piles are not a common deep foundation type in the Washington, DC Metro Area market. As a result, less regional data is available for these foundations compared to other alternate deep foundation types. Displacement cast-in-place piles (DCIP) differ from traditional Auger Cast-In-Place (ACIP) piles in that the pile annulus is formed by pushing a partially-flighted, auger bit to depth via a large mandrel. The auger bit includes a displacing body near the bottom of the tooling. Therefore, little to no spoils are generated during installation and the soil around the annulus is largely densified in-place due to the displacing body being slightly larger than the mandrel it is attached to.Due to this densification, one would expect that the theoretical DCIP capacities (compression or tension) would be greater than an ACIP pile (assuming a pile of similar length and diameter). After 20 static load tests and the installation of over 6,000+ piles on the MGM National Harbor Casino Project, the differences in pile support characteristics between DCIP and ACIP piles of same size and depth was small. The performance of both pile types depended on the density and type of soil within the bearing stratum. In some early cases of DCIP use, the performance exceeded expectations and appeared to be more in line (or better) than typical capacities obtained from driven displacement piles. Other times, the tip elevations could not be achieved or were so difficult to achieve that installation delays occurred and/or significant additional engineering effort was required to address piles short of their requirement embedment.This paper will discuss the limitations of DCIP pile installation in dense Coastal Plain soils and will present the lessons learned during this project. The paper will also compare the DCIP pile type to both conventional ACIP and driven displacement piles utilizing regional and site-specific load test and installation data."

Jan 1, 2017

By Seung-hoon Lee

The use of piled raft foundations has been considered as an economical alternative to conventional piled foundations because a portion of the applied load is carried by the raft in the design of piled raft foundation. In analyzing the behavior of a piled raft foundation as a settlement reducer, an accurate estimate of settlements of the system should be made on the basis of the understanding of nonlinear behavior of piles in layered soils as well as the interaction between the raft, soils, and piles. Although the 3-dimensional finite element method and simplified analysis methods have been used for the design of piled raft foundations, these methods were found to be inadequate for the practical purpose or could not consider the interactions properly. This study developed an approximate hybrid method of analysis to be used for the practical design of piled raft foundations considering pile-soil, raft-soil, pile-soil-pile and raft-soil-pile interactions. In the presented method of analysis, the settlements of the system are estimated satisfying the compatibility of two separate models which are the flexible raft model consisting of 2-dimensional finite elements supported by springs representing soils and piles, and the group-pile model embedded in layers of soil having different properties. Comparisons with other analytical methods as well as a 3-dimensional FEM program were made to verify the sufficient capabilities of the proposed hybrid model for application to practical design and analysis of piled raft foundations.

Jan 1, 2008

By N. C. Matheson

The West's Shell Pile has been used on sites with very soft ground conditions for over 60 years. Fibre reinforced precast concrete shells 900mm long are threadled onto an internal mandrel which can be extended according to the depth driven to attain the load bearing resistance. On completion of driving the mandrel is removed leaving the precast shells to form a permanent lining to the cast insitu concrete core. To give resistance to high contamination, a tar based epoxy coat is sprayed on the outside of the shells or a flexible PVC liner is installed inside the shells to protect the core. Fundamental to the resistance to contamination is the quality of the precast fibre reinforced concrete shell, the mix design and method of manufacture. A series of detailed laboratory experiments were carried out using samples immersed in concentrated acid and sulphate solution. The long term effects of exposure to contamination is recorded in the case studies of existing piles at two gasworks sites.

Jan 1, 1989

By Peter J. Nicholson

Since the reintroduction of soil mixing to the United States over 10 years ago, the work installed by soil mixing technology has grown dramatically. From an annual turnover of less than ten million dollars per year the volume of soil mixing put in place has grown to an estimated $40 million per year in the year 2000. The majority of work done to date has involved walls, either for excavation support, permanent retaining structures or hydraulic cut-off walls. The other major use for soil mixing has been for mass stabilization of soils whether for isolation of contaminants or for retaining structures. This paper will discuss the uses of and costs of typical soil mix structures. BACKGROUND Soil mixing is defined as the in-situ combining of reagents, typically cement, with native soils, the purpose being to modify or improve the ground. This history of soil mixing covers only the use of cement slurry, aggregated with soil in-situ by mechanical mixing methods only. Soil mixing by use of high-pressure hydraulic means, also known as Jet Grouting, will not be discussed. In addition this will not cover ex-situ (above ground) mixing, or mixing dry reagents with soil. Only mixing applications for building, civil and heavy construction applications will be discussed, with only passing reference made to uses of soil mixing for environmental remediation work.

Jan 1, 2001

By J. Osterberg

A new device has been developed for load testing driven piles and drilled shafts which consists of an hydraulic jack or bellows which has a telltale rod fastended to the bottom. The rod extends upward to the surface through a pressure pipe. When pressure is applied, the jack or bellows expands, applying an equal upward and downward load at the bottom. The downward movement at the bottom is indicated by the rod and the upward movement is indicated by the movement at the top. Thus, upward and downward load-deflection curves can be drawn. As load increases, failure will occur either in end bearing or friction. Results of field installations are described. Total loads of up to 1,100 tons metric have been used. The method obviates the need for the reaction load required for the conventional pile loading test and separates friction and end bearing. It is especially advantageous for use over water, in crowded spaces and for inclined piles.

Jan 1, 1989

By Peter Faust, Jeremy Zorne, Timothy Siegel, Diane Fiorelli

Professional sport venue construction follows a very simple rule. Once the decision has been made to move the team to a new place, construction shall begin immediately, so that not more than one or two seasons pass by stuck in the old home. Such tight construction schedules require a different approach than traditional design-bid-build contracts. Design is mostly done on the fly, the construction schedule becomes a main risk factor and an early contractor involvement is desired. As specialty contractors become more and more sophisticated, owners, their construction managers or the general contractor have realized the value of ideas and modern technology they can bring to the table for a successful and fast project completion. Local knowledge and experience in a variety of solutions play a key role in the specialty contractor’s ability to provide added value to the project. This is also true for the specialty foundation contractor, who needs to understand the complexity of such modern structures from its integrate foundation, over the delicate concrete structure to a potentially fancy movable stadium roof. Not to mention all the modern high tech equipment which shall make such a place a great customer experience. His expertise shall enable him to propose the most suitable foundation element for the given ground condition and application. Rather to build what others have designed, his strength is to propose alternate concepts which will be faster and (hopefully) more cost effective. This paper highlights different value engineering (VE) input a specialty foundation contractor had on 3 major sports arena projects in California. Together with the entire team from owner to GC, including the Geotechnical (GEOR) and the Structural Engineer of Record (SEOR), the most efficient and best performing foundation solution can be found every time. But such an approach also requires the open mind of the owner to entertain last minute changes when the permit drawing set has already been submitted for approval.

Jan 1, 2018

By Jamey B. Rosen

As Project Information Management Systems (PIMS) technologies develop, the range of projects to which one can apply these technologies grows while the cost to apply them shrinks. In recent years, technologies previously limited to large “megaprojects” (e.g., major dam rehabilitations) owned by major entities (e.g., the United States Army Corps of Engineers) with large budgets have been applied to smaller projects with less stringent specifications and more modest budgets. This paper will describe applications of PIMS technologies to small projects with limited budgets, including examples from levee construction, small-scale grout curtain installation, and diaphragm and secant pile cut-off walls. We will include a demonstration of how PIMS technologies can effectively analyze verticality data from koden and hydromill data streams to automatically generate models and as-built drawings showing overlap and deviation along the depth of the foundation. INTRODUCTION This paper discusses the application of Project Information Management Systems (PIMS) technologies to geo-foundations projects, with a focus on technologies and examples that are in a lower cost range. PIMS technologies allow contractors and other stakeholders to perform efficient quality control on their data, generate quick or automatic reports and as-built drawings, perform analyses to better understand their construction, and ultimately use their data to increase the quality of their construction. As PIMS technologies are relatively new to the deep foundations industry, and owner specifications on their use are generally viewed as complex and limited to large scale projects, PIMS technologies are frequently viewed as an expensive component that is beyond the scope of a smaller or simpler project. However, the same principles and techniques generally associated with large projects can be applied to projects at smaller scale. Furthermore, as these technologies develop both in the deep foundations and other industries, the cost of application is decreasing quickly making them even more affordable for smaller projects. The remainder of this paper provides some justification for applying PIMS technologies, describes some scalable data management concepts and workflows and then provides some examples of “low cost” applications of these technologies.

Jan 1, 2019

By Rudolph P. Frizzi

Quality control is essential for augered cast-in-place (ACIP) piles (also known as continuous flight auger (CFA) piles outside the United States) and augered displacement (AD) piles since the pile is constructed below the ground surface out of the direct sight of the personnel constructing and inspecting the pile. ACIP piles are being successfully constructed to support high-rise structures, arenas and stadiums, mass transit systems, and power and industrial facilities. The use of AD pile technology is also gaining ground in the United States, typically utilizing proprietary systems such as Omega (currently utilzed by Richard Goettle Inc., and LG Barcus and Sons, Inc.), Berkel, and DeWal (currently utilized by Morris-Shea). Different types of ACIP/AD pile installation equipment are shown in Figures 1 and 2. ACIP piles are installed into granular and cohesive soils, and soft rock to lengths currently approaching 130 ft (39.5 m), with diameters up to 24 to 36 inches (610 to 915 mm), and sustaining design loads approaching 900 kips (4000 kN). Current AD pile installation equipment in the United States is capable of installing up to 79-ft-long (24 m) piles with diameters ranging from 12 to 18 inches (305 mm to 460 mm).

Jan 1, 2002

Abouleid,A.F.327 Ajdic, I.451 Albert, L.F. 221,307 Alem, A. 525 Asama, T. 431 Avgherinos, P. J. 373 Baker Jr, C.N. 331 Balossi Restelli, A. 171 Beckwith,G.H.33 Bellini, A. 469 Bermingham, P. 481 Bertero,M. 171,535 Beyer, M. 503 Bottiau, M.41 Botto, G. 205 Bruskeland, O. 337 Budhu, M. 349 Bullivant, R.A. 181 Bustamante, M.G. 185, 475, 535

Jan 1, 1994

By Shuvranshu K. Rout, Anup K. Mandal, Biswajit Das, Manos De

"To adopt new technology advancement in Steel Plant, there is a requirement of shifting of operation process from Coke Wet Quenching (CWQ) to Coke Dry Quenching (CDQ). New CDQ chamber foundation with deep basement and underground conveyor tunnel are to be constructed in an operating plant where heavy foundations and structures are located in close proximity. Furthermore, the existing CWQ system will be in operation during new underground construction and erection. Challenges to deep excavation of tunnel and chamber foundation consist of non-uniform ground condition, prevent washing out of soil from bottom of existing foundations, stability of existing nearby structures, presence of large number of underground utilities, ensuring safe underground workplace to construction resources engaged in new construction work along with project schedule and budget constraints. A combination methods involving use of soil nailing, soil grouting, contiguous bored pile and micro pile had been adopted for protection of excavation sides as well as existing structures. Each side of excavation in different stretches were analysed during design as well as construction stages. The use of combination of all techniques in a single brown field project in context of the nature of site constraints and safety issues made this a unique project.INTRODUCTIONSteel Industry is one of the backbones of industrial growth of any developing country like India. Due to increasing land prices most of the steel plants in India are expanding within their existing plant facilities. In addition to that, there is demand of adoption of new technology for future expansion projects to set new benchmarks with global standards.The property owner had earlier installed a Coke Wet Quenching (CWQ) for their Coke Plant. Now, there is a requirement from process department to proceed with Coke Dry Quenching (CDQ). To facilitate the CDQ within the existing CWQ which will be in operation is the main challenge for the property owner. The second challenge is the limited space for underground construction and subsequent equipment erection within the stipulated time frame.From a geotechnical prospective, the project team had uncertainty and reservations in their mind about the construction methodology. Therefore, the role of three “C”: ‘Consultant’-‘Client’- ‘Contractor’ and their combining brainstorming is essential to freeze a working plan for achieving the goal. In this paper, only the excavation support systems for underground foundation structures have been highlighted in the context of solving geotechnical problems."

Jan 1, 2017

By David J. Baxter

Use of bored displacement piles has experienced significant growth in the UK piling market sector, largely due to their environmental advantages over other piling methods and through cost benefits. Bored displacement piles are a cast-in-situ construction which can be formed with minimal production of spoil and offer low noise and vibration compared to driven displacement piles. A large variety of bored displacement piles have been developed. This paper describes a standard system for their classification. The development of the different types is described along with the factors which have led to their increased use. Consideration is given to processes undergone by the soil during pile installation and design approaches for bored displacement piles are compared. Comparisons are made between the different classifications of bored displacement pile. Comments are also made on the installation of such piles. It is concluded that complex changes occur in the stress states of the surrounding soils. Such effect of the pile installation on the soil should be accounted for and there is a need, therefore, to further refine the design process for these piles.

Jan 1, 2006

By Flor De Cock

The paper reflects part of the work from the European Regional Technical Committee on Piles (ERTC3) during its mandate between 1994 and 1999, and, in particular, describes the find­ings from an International Seminar held in 1997 in Brussels on European practice for design­ing axially loaded piles. The seminar included contributions from 17 European countries, each of which provided a synopsis of their respective national design approaches. This paper pays particular attention to the design methods based on laboratory and in-situ test data for both bored and displacement piles.

Jan 1, 2002

By T. Soejima

In recent years, there has been a tendency in the field of foundation piling works to utilize piles of greater bearing capacity in order to meet increasing height and weight of modern building as a means of saving of piling cost. To satisfy these requirement, a new technique for large diameter bell bottom cast-in-place piling has been developed utilizing multi-head reverse circulation drilling system.

Jan 1, 2010

By James A. Schneider

The evolution of the American Petroleum Institute (API) design method for axial capacity of driven piles in siliceous sands is explored, and complemented with an overview of how changes in offshore site investigation practice have increased the level of knowledge with respect to vertical variability of soil characteristics. Increased use of the cone penetration test (CPT) provides near continuous profiles of soil type and strength which can be used in calculation methods that address variation in local shaft friction rather than the API method which seems to have initially been based on observations of average shaft friction in relatively uniform sand deposits. Development of a formulation for CPT correlations to axial pile capacity in sand is discussed, along with implications to existing factors of safety used in routine design.

Jan 1, 2006