Search Documents

By Stefan Larsson, Sebastian Adevik, Sadek Baker, Razvan Ignat

"Abstract Uncertain strength, deformation and flow properties in dry deep mixing columns often lead to conservative choices concerning design values where the design is regularly complemented with a surcharge fill. The surcharge not only leads to increased cost but also to logistical problems where the surcharge is a physical obstacle. The deformation properties of a ground improvement were studied by means of two small embankment load tests. The settlement measurements were also used in FEM analyses, where the effect of surcharge on creep settlements was investigated. Based on the results, the effects of the surcharge were considered negligible and could safely be ignored. The project is an example how the contractor can use a field test as an effective design approach.IntroductionGround improvement of soft soils with dry deep mixing columns, or lime-cement columns, is often combined with a surcharge fill. The main reason for using a surcharge is to force the primary settlement and some of the secondary settlement that would have occurred under the final embankment height alone, to take place under the surcharge loading. Another reason is to level out uneven settlements. Strength and deformation properties in improved soil cannot be sufficiently assessed in advance, before columns have been tested on-site, and this uncertainty often lead to conservative choices concerning design values. In order to compensate for a slow forecasted consolidation process, the design is regularly complemented with a surcharge. The surcharge not only leads to increased cost but also to logistical problems where the surcharge is a physical obstacle.Extensive research undertaken by Åhnberg (2006, 2007) shows, by means of triaxial and oedometer tests, that cementation processes and a load acting on the columns during hardening, makes the improved soil to behave as a heavily over-consolidated soil due to an increase in quasi pre-consolidation pressure. The effects of using a surcharge on the time for consolidation and creep properties are thus probably small, since the stress level does not normally exceed this quasi pre-consolidation pressure. A study presented by Venda Oliveira et al. (2013) shows that the stress level within small ranges has limited effect on the creep properties.This paper presents a case study where the deformation properties of a ground improvement using dry deep mixing columns was investigated by load tests on two small test embankments. The tests were performed at the Interchange Värtan project site, which is part of the Norra länken infrastructure project in Stockholm. The tests were not performed as a research project but simple load tests performed by the contractor with the purpose of rationalizing the design delivered by the client. One purpose of the load tests was to assess the deformations when the columns are loaded temporarily by overlaying concrete works. Another purpose was to provide some input data to a study of the effects of using surcharge on creep settlements. The analysis was conducted as finite element modeling using the commercial code PLAXIS, where creep settlements can be simulated using the built-in Soft Soil Creep model."

Jan 1, 2014

By Fawad S. Niazi

Ever since the use of the cone penetration test (CPT) in geotechnical practice, attempts have been made to correlate CPT parameters with pile capacity components of unit end bearing (qb) and unit shaft resistance (fp), thus deriving multiple CPT-based pile design methods. These methods focus on "capacity" only without consideration to complete axial pile load-displacement (Q-w) response. Estimated capacities from these methods also exhibit considerable scatter without any consensus on their consistency. In addition, load-displacement curves obtained from axial load tests on highly expensive and extensively instrumented piles can exhibit different shapes. Nevertheless, a single value from the curve so obtained dictates the design capacity. Currently, there are at least 42 different criteria defining capacity with considerable variation in the values obtained thereof. The Randolph elastic solution, which provides a framework for analytical evaluation of pile load-displacement response, requires the profiles of soil stiffness. The fundamental soil stiffness defined by the small-strain shear modulus (Gmax) can be obtained from shear wave velocity (Vs) readings via seismic piezocone tests (SCPTu). The secant stiffness (G), which softens from Gmax corresponding to operational load levels, can be obtained by generating stiffness reduction curves from back analysis of load tests. Then, using appropriate G values, the Q-w curve can be defined for conditions similar to the database from the pseudo strain (w/d). Thus, a complete framework for optimal integration of SCPTu data, Randolph elastic solution and back-analysis of field operational stiffness can be established for complete axial pile foundation analysis.

Jan 1, 2011

By K. Rainer Massarsch, Bengt H. Fellenius

"Abstract Vibrations generated during the driving of piles or sheet piles can affect buildings or installations in the ground. However, observed building damage is not always caused directly by dynamic effects, but can also be related to foundation conditions. The importance of geotechnical conditions is usually not taken into consideration in most vibration standards. This paper describes how building foundations, and in particular mixed foundation types, are especially sensitive to ground vibrations. A method is presented for assessing the risk of settlement due to vibrations in granular soils. Also, a simple concept is proposed for estimating settlements in the vicinity of driven piles.1. INTRODUCTIONUnder unfavorable conditions, the installation of piles or sheet piles can cause damage to buildings or other structures on the ground. Frequently, such damage is attributed to vibrations of the building itself. In many countries, national or international standards are used to assess the risk of vibration damage to buildings. As such standards are often prepared by engineers with little or no geotechnical knowledge, the effects of ground conditions on vibration propagation and damage to building foundations are generally not recognized, and damage criteria based solely on the dynamic response of buildings neglect the importance of damage mechanisms governed by geotechnical conditions. One potentially important damage mechanism is differential settlement below buildings, especially when these are founded on loose granular soils. When seeking guidance in the literature, little or no information can be found regarding methods to assess permissible levels of ground vibrations with respect to risk for settlement.This paper focuses on building damage that can be attributed to foundation conditions. In the case of ground vibrations due to pile and sheet pile driving, differential settlements are of particular importance as the ground vibrations attenuate relatively rapidly from the source. Consequently, settlement below part of the building, which is located close to the vibration source, can be significantly larger than at a distance further away.Piles are often a cost-effective foundation solution for buildings on loose and compressible soil, frequently located in urbanized areas. Sheet piles are commonly used as support for deep excavations. While impact driving is most commonly used to install piles, vibrators are frequently used for driving (and extraction) of sheet piles. It is important to recognize the fundamental differences between impact and vibratory driving. During impact driving, the pile is subjected to stress waves of short duration. The driving process creates vibrations, which radiate from the shaft and/or the toe of the pile into the soil. The larger the intensity of the stress wave, the larger the dynamic force and the intensity of ground vibrations. In addition to the vibration intensity, which often is expressed in terms of particle velocity, also the vibration frequency is important. When the dominant frequencies of the generated vibrations harmonize with the resonance frequency of buildings or building elements, the risk of building damage increases."

Jan 1, 2014

There are many ways to classify structural slurry wall elements, but the DFI committee chooses to limit these descriptions to three functional requirements, namely: design function, plan configuration and type of panel reinforcement. (See Figure 1 in Part IV for panel classification). Slurry walls can function as: 1. Curvilinear or linear elements for temporary and/or permanent structures to resist lateral forces transferred from the ground, water, earthquakes and various surcharge loads. 2. Load bearing elements in various plan shapes to resist vertical forces. 3. Combination Elements to resist combined forces under conditions 1 and/or 2. For example, elliptical shafts with various openings for tunnels and conduits have been commonly used for deep excavations.

Jan 1, 2005

By Paul J. Lewis

Estimation of the axial side shear resistance of drilled shaft rock sockets is directly related to the unconfined compressive strength of the bedrock. Commonly, the mean unconfined compressive strength value is calculated from a range of laboratory test results and is used to estimate the side shear of the bedrock. This paper presents the results from a full scale axial load test performed on an 8.5-feet-diameter drilled shaft rock socket, and compares measured side shear values to estimated values for two different rock strata. Measured side shear values correlated well with the design value calculated for the "strong" rock stratum, but did not correlate well with the design value calculated for the "weak" rock stratum. The mean unconfined compressive strength was used to calculate the side shear in both strata, but review of the laboratory data indicates that this value may not have been appropriate for the weak stratum due to a large variation in the laboratory test results. Also included in this paper is a discussion of the subsurface conditions, the laboratory test results, and the methodology used to design the drilled shaft rock sockets for axial and lateral resistance.

Jan 1, 2005

By Thomas Passlick

By means of further developed machines and techniques and with growing experiences in jet grouting, the challenge of this building method becomes more and more complex. To keep the concerning risks as low as possible, the requirements on the quality assurance continuously in­crease. The construction of a 37.0m deep seated slab for the Amsterdam metro station Vijzelgracht in marine clay represents such a complex task. This paper summarises the required measures of quality assurance. In particular a new hydraulic measuring device is introduced with which it was possible to detect the column diameter of 2.6m at a depth of 37.0m during the production process and with a very high accuracy.

Jan 1, 2006

By B. Soundara, A. Suganya, S. Selvakumar

"Expansive soils have a potential for shrinkage or swelling under changing moisture content. Attempts were made to reduce the swelling potential of expansive soils with conventional additives such as lime, cement, etc. and non-conventional additives such as industrial wastes. In this research an attempt is made to study the feasibility of using granulated waste expanded polystyrene (EPS) as an additive to expansive soil to control swelling. To investigate the effect of mixing waste EPS granules with expansive clays, three expansive soils with different plasticity index were manufactured in the laboratory by mixing sand with sodium bentonite of various proportions. A series of standard proctor test, California bearing ratio (CBR) test, one dimensional free swell and swell pressure tests were performed on these soils. Test results show that the inclusion of EPS granules significantly reduces the percent swell and swelling pressure when subjected to one-dimensional free swell conditions. The dry density and CBR values decrease with increase in EPS content and increased plasticity of the soil.INTRODUCTIONExpansive soils cover an area of about 257 Million hectares on the earth’s surface (Dudal et al. 1965). In India, the area covered by expansive soils is nearly 20 percent of the total area (Mohan et al. 1961). Movement is usually in an uneven pattern and of such a magnitude as to cause extensive damage to various structures, especially lightly loaded structures or pavements (Chen 1975). Stabilization is one of the methods of treating the expansive soils to make them fit for civil engineering purposes. The variety of stabilizers may be broadly divided into three groups (Petry et al. 2002): (a) traditional stabilizers (lime, cement etc.), (b) by-product stabilizers (fly ash, quarry dust, phosphor-gypsum, slag etc.) and (c) non-traditional stabilizers (sulfonated oils, potassium compounds, polymer, enzymes, ammonium chlorides etc.). Apart from these, a number of other ground improvement techniques such as sand cushion technique (Satyanarayana 1966); cohesive nonswelling (CNS) layer technique (Katti 1978) were adopted for the stabilization of expansive soils. Expanded polystyrene (EPS) is a polymeric foam normally available in white colour and is a wellknown packaging material. The geotechnical specialists recognize EPS as the most commonly used geofoam material, a type of cellular geosynthetic which has been in consistent use in geotechnical applications since the early 1960s (Horvath 1995). EPS has very low thermal conductivity and nearly 98% of the volume is air (Lye et al. 2002). EPS has many exceptional properties such as being lightweight, thermal insulating, shock-absorbing and having low-water pick-up, etc. EPS find its applications in geotechnical engineering as light weight fills in the form of blocks (Refsdal 1985, Karpurapu et al. 1992, Zou 2001, Ikizler et al. 2008). EPS can be used as compressible inclusion and as a vibration damper (Horvath, 1994&1995). EPS is also used in lightweight concrete owing to its lightweight, excellent heat preservation and sound insulation properties (Ravindrarajah et al. 1994; Miledet al. 2004 and Babu et al. 2005). Waste EPS granules have been used in with horticultural soils to improve a number of soil characteristics like improving drainage, lightening heavy soils and improving water uptake capacity of soils (Scheirs 1998). Furthermore, it was also used as sub-base materials for pavements and railway track beds (Hanna 1978; Duskov1996), construction materials for floating marine structures and fenders in offshore oil platforms (Bagon et al. 1976), sea beds and sea fences; as an energy absorbing material for buried military structures, (Perry et al. 1991)."

Jan 1, 2017

By Mario Aiezza

This paper outlines the results of a relationship developed during the design and construction of the foundations for the Gallery Towers project in Melbourne. Both the builder and the piling contractor were determined to arrive at a satisfactory foundation solution to the problems encountered at the site. The scope of piling work was to provide load-bearing piles under the building columns, some of which were located within a retention system that also required a piling solution. Geological conditions were variable and challenging. The site area was small and located adjacent to the National Arts Centre in the developed Southbank area, a high density office area. This presented logistical problems in limiting construction traffic on site and also demanding minimal noise and vibration emanating from piling activities. The piling contractor, Vibro-Pile, and the builder, Walter Construction Group, faced the challenges presented with a refreshing cooperative attitude that was beneficial to both companies. Commercial issues rising from design and construction problems were first put apart in order to allow the respective technical department of each company to work with minimum constraints to achieve the most cost effective solution. In the process usual adversarial attitudes resulting in loss of time and money was avoided. A number of issues were addressed successfully at minimum cost and time during this contract. Despite the difficulties encountered, the job was completed on time and with negligible claims for extras, resulting in the development of a strong mutual respect between both companies.

Jan 1, 2002

By E. R. Wang

This paper outlines the engineering properties of shallow soil in Shanghai area. The main points that should be paid attention to during deep foundation investigation, and general conditions of experimental soil engineering are discribed.

Jan 1, 2010

By M. D. Khattar

The paper describes the salient construction features of the Pile foundation work for the Railway viaducts in Algeria. Six viaducts were constructed for execution of the Railway line between Aintemouchent and Benisaf in Algeria. The work was executed by the Indian Railway Construction Company Limited of India (IRCON) for the Algerian National Railways (S.N.T.F.). These six viaducts had multiple spans of 36M resting on hollow piers of heights upto 69M. Most of the piers were founded on piles of 1 and 1.2M dia bored piles going upto 22M deep through cal­careous rocks and were designed for Railway loading in seismically active area. The work involved 356 piles & constituted a very important aspect of the whole work. The concrete in the piles was made with sulphate resistant cement and the integrity of the concrete was tested with Sonic method so as to ensure the quality. The piles were driven with the help of a hydraulic oscillator and the concrete was laid with a tremie pipe. Problems as encountered during execution have been explained.

Jan 1, 1989

By Luo Yang

A one-dimensional wave equation based algorithm for estimation of shaft and toe resistance of driven piles using High Strain Testing (HST) data is presented. The pile is represented by a uniform elastic bar, while the soil around the pile is assumed as a homogenized isotropic medium, and Smith model is adopted to represent soil-pile interaction in the wave equation analysis. In most cases, the displacement of pile particles along pile shaft is greater than recoverable soil deformation (i.e., soil quake in Smith model). Therefore, static shaft resistance could be reasonably assumed to be totally mobilized during pile driving. Smith damping factor is used to account for combined dynamic and rate effect. Force and velocity time histories measured at the pile head are used as input boundary conditions in an analytical solution of the one-dimensional wave equation. As a result, two unknown parameters, static shaft resistance and Smith damping factor, can be incorporated into the one-dimensional wave equation and determined analytically for the time duration prior to the first downward wave reaching the pile toe. Then, soil resistance and Smith damping factor at pile toe can be further determined. The advantage of the proposed analysis technique is that the Smith damping factor and the static soil resistance can be directly determined based on the closed-form solution of the one-dimensional wave equation, which is computationally efficient. Numerical examples are given to illustrate the use of the proposed method to determine the pertinent Smith model constants and the static resistances.

Jan 1, 2006

By Philip J. Daynes

As part of the regeneration of the centre of Dublin, a multi-functional development is being constructed on the site of the historic Smithfield Fruit Market. The site is being developed in three phases, and includes one of the deepest basements (10m) constructed in Ireland to date. Until the recent improved economic climate, there has been little requirement for deep basements in Dublin, and this is the first to be constructed entirely within fluvio-glacial gravels and boulders. The difficult ground conditions led to the adoption of a diaphragm wall solution to ensure a watertight construction. Tie-back anchorages are utilised in the temporary case, and the wall is propped by floor slabs in the permanent case. Where required by high bedrock levels, the diaphragm wall is dowelled into limestone bedrock to ensure toe stability. The recorded lateral movement of the wall is significantly below that calculated by numerical analysis. Temporary bentonite cut-off walls were installed to divide the site into discrete sections. The basement was constructed as a tanked structure, and is subject to uplift water pressure. Passive tension minipiles provides an innovative alternative to the standard stressed anchorage solution. This paper describes:- design and construction aspects of the diaphragm wall, tie-back anchorages, and anti-flotation minipiles, together with recorded lateral wall movements,

Jan 1, 2003

By Roy Peratrovich

An innovative cost-saving design for a 1,100 ft bulkhead on the Tanana River at Nenana in central Alaska won Alaska Construction & Oil magazine's Construction Achievement Award. The designers utilized materials available nearby at low cost. They planned sheet pile enclosures, self-anchored back into shore without cell closures. They made it practical for inexperienced local workers to do the building. And they completed the project on time and below a reduced budget.

Jan 1, 1985

By Mostafa Mossaad, Ali Helwa, Manal Salem

Support of excavation (SOE) design practice tends to model SOE elements using two-dimensional (2D) analyses to avoid the complexity associated with three-dimensional (3D) analyses. Such practice overlooks soil arching in the horizontal plane and prevents designers from accounting for elements such as capping beams as part of the statical system. This study simulates square excavations supported by cantilever slurry walls in dry cohesionless soil using 2D and 3D finite element (FE) models. First, side support wall behavior is compared from 2D and 3D FE models for variable excavation length to depth (L/H) ratios. Second, the effect of slurry wall lateral bending stiffness on wall behavior is studied by modeling the wall using plate element with isotropic and anisotropic wall stiffness. Finally, the sensitivity of cantilever wall behavior to the presence of capping beam is illustrated. The study concludes that unbraced excavations with L/H ratios greater than 5 almost resemble plane-strain conditions. Slurry walls are better simulated in 3D FE models by dividing the plate element into discrete panels or by assigning anisotropic bending stiffness to the plate element. Finally, the presence of capping beam affects the behavior of cantilever walls resulting in reduction of deflections and redistribution of bending moments. INTRODCUTION Support of excavation (SOE) design practice ranges in complexity from conducting simple hand calculations to performing three dimensional numerical modeling depending on several factors among which is the geometry of the design problem. This paper addresses walls that are designed using numerical modeling, and discusses the factors governing the choice of the most suitable modeling approach. It has been believed for a while that modeling excavations using 2D numerical models would lead to a more conservative solution, which turned out to be incorrect in specific cases. This paper attempts to describe cases where 2D finite element modeling could be on the conservative side and other cases where it could be less conservative than the more complex 3D modeling.

Jan 1, 2018

By Yogesh Prashar

Three conventional uplift tests and 12 Rapid Pile Load Tests (RLT) were performed on total of fifteen 16-inch square pre-cast concrete driven piles at a test site in Emeryville California in December of 2000. The uplift tests were performed in accordance with ASTM standards, and the RLTs were performed using a FUNDEX RLT. The RLT is carried out by dropping a mass of 25-tons on top of the pile, thereby inducing a force that is measured by a load cell. An optical lens records the vertical deflection of LED's that are mounted on the pile. Ultimate uplift and compression capacities of each of the fifteen piles were determined using the Davisson method. Soil parameters were calibrated by back-calculation (cohesion and internal angle of friction) using both the results of conventional uplift load versus deflection curve, as well as the results of the triaxial compression tests. A two-dimensional finite difference model including soil elements, and structural elements representing the test pile was setup using the computer program Fast Lagrangian Analysis of Continua (FLAC). FLAC was used to simulate both the uplift as well as the RLT. Strength increase of cohesive material was also accounted for in the analysis. Numerically simulated and theoretically computed pile capacity curves and axial deformation variation with applied load curves are in close agreement to the observed curve during the field test. Conclusions are made from this test site regarding the factors influencing results of RLT.

Jan 1, 2002

By Tsunenobu Nozaki

"AbstractThe PRESS-IN METHOD is widely recognised as “an environmentally friendly piling method”. However, this characteristic is only one of the fundamental advantages of the method and this paper presents the most up-to-date capabilities of the method. Due to the evolution in recent years, the Press-in Method is now applicable to 2.5m thick retaining walls, over 50m deep foundations, overcoming rock conditions and confined construction conditions.The Press-in PrinciplesThe basis of the Press-in Method is simple. The Silent Piler presses a pre-formed displacement pile into the ground by static jacking force. The reaction for the Press-in Force is generated by gripping previously installed piles. As a pile is pressed into the ground, “A Pressure Bulb” is formed around the pile toe. Accordingly, higher bearing capacity can be generated compared to driven piles without disturbing the ground and producing any vibration. (A comparison of jacked, driven and bored piles in sand (2005), Deeks et al.)Applicable Pile ProfileThe Press-in Method is applicable to most of the steel piles available on global market i.e. U sheet pile in single form and pair, Z sheet pile, also in single and pair and Tubular Pile as described in Figure 2. Wall thickness of those piles can be 0.3m to 2.5m and moment of inertia of the wall ranges up to about nine million biquadratic cm per meter, which can deliver similar elastic modulus EI (kNm2/m) to 2.0m thick diaphragm walls and can be utilised for extremely deep excavations required in today’s construction industry"

Jan 1, 2014

By David C. Kraft

A major manufacturer and user of machine tools had the need to install a screw press machine at its plant site with the following design load requirements: (1) Vertical Compression Live Load = 2000 kip (8896 kN) and Dead Load = 1000 kip (4448 kN), (2) Rotational Moment = 6600 ft-kip (8950 kN'm). The screw press machine was to be located within an existing manufacturing building. The bottom of the footing base was located 15 ft (4.6 m) below existing floor slab. A geotechnical investigation of the site indicated a 17 ft (5.2 m) thick initial stratum of stiff to very stiff clay underlain by a 14 ft (4.3 m) thick stratum of loose to medium dense sand. Beneath the sand stratum was soft rock described as weathered shale. Obvious concern was raised on the possible effects of the dynamic motion of the screw press and potential resulting settlement within the loose sand stratum. This combination of large loads and dynamic motion resulted in the selection of a helical pile and tieback system to support the concrete foundation. The helical pile foundation system consisted of a group of vertical helical piles installed into the shale rock and a group of inclined helical tiebacks set into the remaining portion of the clay stratum. Four load tests were conducted on the vertical helical piles in order to establish compression load capacity. The results of these load tests as reported herein, led to the addition of a limited number of tubular steel push piles in order to meet the project required Factor of Safety on the design loads. All of the helical piles, push piles and inclined helical tiebacks were successfully installed and the screw press is now installed and operational.

Jan 1, 2003

By Alan G. MacKinnon

Loads and stresses from pile driving are increasing from heavier piles and more powerful hammers. Stresses can be dangerous to equipment stability. Equipment developer MacKinnon tells how to compute stresses for all positions of the crane boom and angles of pile batter. From a paper presented at the DFI-University of Hawaii Seminar, April 1985.

Jan 1, 1986

By R. Stenne

This paper deals with a complementary soil investigation which being part of the contract helped understand the behavior of a softened clay and adjusted the design of a retaining structure accordingly. The investigated softened clay proved to have lost its original strength but had maintained some characteristics of its stress history and in particular high horizontal stress. Pressuremeter tests and flat dilatometer tests were of interest to estimate the at rest earth pressure. A design consisting of a T-shaped slurry wall in conjunction with transverse walls was the most effective solution to cope with high active pressures and low passive pressures.

Jan 1, 2000

By Damian R. Siebert

Risk-reduction measures implemented during the design and construction of a 21-story pile-supported building adjacent to a below-grade 100-year-old sewer structure were keys to a successful foundation system. Avoiding damage to the existing sewer structure during construction activities and the future ability to access the structure post-construction were the main concerns for the utility owner. Clear communication and a deliberate design process between all parties ? utility owner, building owner, structural engineer, geotechnical engineer, architect, and contractor ? were integral to the project?s success. This collaborative process helped all parties to understand the risks, both real and perceived, and to develop mitigation measures to reduce the risks. Bringing together all parties to engage in dialogue and encouraging open communication throughout the project were paramount to its success. By implementing the joint design plan, using mutually-acceptable construction techniques, and careful monitoring, the building foundation was successfully installed and all parties? risks were averted.

Jan 1, 2011