Search Documents

By G. Hausen, H. Micka

"Modern signal and power electronics made adjustable-speed AC drives technically feasible and reliable and economically attractive. Cycloconverters are discussed as a proven technology for mine hoists. \IntroductionUntil rather recent technical and commercial advances in power and signal electronics, DC motors were used almost exclusively for applications requiring continuously adjustable operating speeds and torques. More recently, the significantly higher efficiency and the accordingly lower operating costs of AC motors gained importance. An effective and efficient speed control of AC motors requires the control of AC voltage and frequency. Table 1 shows typical applications of adjustable-speed AC drives.CycloconvertersOf particular interest to the mining industry are cycloconverters for hoist drives. The cycloconverter represents by far the simplest, most efficient and most economical means of converting a constant-voltage, constant-frequency supply into an adjustable-voltage, adjustable-frequency supply as required for the speed control of AC drives operating in the frequency range to half of the utility frequency.Cycloconverters feeding synchronous motors or induction motors are ideally suited for slow-speed direct-coupled drives."

Jan 1, 1988

By Fred W. Brackebusch

"The use of paste technology for surface tailings disposal may offer economic, technical, safety, and environmental advantages for both underground and surface mining operations. Paste is a non-Newtonian fluid having some shear strength during transport and placement. The strength is augmented after placement by consolidation, water loss, and by addition of chemicals. Economical dewatering systems are necessary to the success of surface paste tailings disposal. In an underground mine, the paste backfill plant can produce paste for surface disposal about 50% of the time because only about 1/2 of the tailings are needed for backfill. The distribution of paste to the surface stack involves expensive pumping equipment and thus a nearby location of the stack is desirable. The viscosity of paste can often be manipulated by modifying pH. Placement of the paste in a designed stack configuration depends on topographic and climatic factors as well as paste properties.INTRODUCTIONThe use of paste technology for mine backfill is becoming accepted for underground mines mainly because of ground control and economic reasons. Paste technology is just starting to be applied for tailings disposal with only a few hardrock metal mines worldwide using the technology; however, it has been used extensively for red mud disposal in the aluminum industry. The disposal of dry tailings is very attractive from environmental and safety points of view because of limited water which might potentially escape and pollute river systems. Dry stacking systems, however, are expensive because of filtration and truck transportation costs. Paste can be produced from most tailings streams by special types of thickeners. Furthermore, it can be transported in pipelines, therefore paste technology may be more economic than dry stacking but still have some of the major advantages. Understanding of paste technology has improved through experience with operating underground backfill systems in recent years and because of testwork and research programs by mining companies, consultants and equipment vendors. Thus we may be on the verge of taking a new look at tailings management using paste technology."

Jan 1, 2002

By Arthur Notman

For the period January 1st, 1942, to January 1st, 1946, the American Bureau of Metal Statistics records the gold production of the world as 118,788,000 fine ounces. If we include 1946 at the same rate as 1945 (26,- 590,000), we arrive at a total of 145,378,000 fine ounces in the past five years . Included in these figures are estimates of Russian output at 4,000,000 ounces per annum for the five years, and 1,300,000 ounces per annum for Korea and Japan. The remaining 120,000,000 ounces represent the aggregate production from official reports of the other gold producing areas of the world, with the exception of the 1946 figures, as noted above. At $35.00 per fine ounce, this represents $5,188,230,000. According to the reports of the Federal Reserve System of the United States, on December 31st, 1941, the monetary gold reserves of the United States were $22,736,- 600,000 (at $35.00 per fine ounce) , while on October 31st, 1946 (latest available) , they had fallen to $20,402,000,000, a decline of $2,334,600,000. Adding this decline to the value of the new production for the five years, we have a total of $7,522,830,000, which has been absorbed by the rest of the world since Pearl Harbour, a rate of absorption of over $1,500,000,000 per annum. This has taken place at a rime when the advocates of purely managed currencies had convinced many people that gold performed no really essential function in the world's economy, and that we could get along perfectly well without it. It was pointed out that gold could not be eaten, it could not clothe our nakedness, it could not shelter us from storms, and, therefore, it was a non-essential, even though it could be used to settle international balances of trade. Apparently, the world as a whole still regards it as preferable to the paper promises of governments, however sound, relatively, they may appear. Actually, we have no way of measuring the true strength of this feeling, because the principal governments of the world have made it legally impossible for their citizens to own gold, except in the form of ornaments.

Jan 1, 1947

By David Clarry

?The issue ?reduction requirement ?Planning abatement steps ?Energy Management & Energy Efficiency ?Energy Recovery / Utilization ?Alternative Energy Professional Services Overview ?Capital Projects and Construction ?Project Development and Planning ?Engineering ?Project management ?Construction management ?Consulting ?Process ?Business ?Environmental ?Technology ?Operational Services ?In-house engineering services for operations

May 1, 2009

By Richard Maurice

RÉSUMÉ La restauration du site minier Poirier, à Joutel s?est déroulée entre 1998 et 2001. Le principal élément des travaux a été la restauration du parc à résidus et des zones d?épanchement qui totalisaient 4,5 millions tonnes de résidus répartis sur une superficie de 74 hectares. Les résidus sont fortement générateurs de drainage minier acide. La première partie de la présentation consiste en un bref rappel du concept de restauration suivi d?une description des principaux éléments de travaux avec l?emphase sur les leçons apprises de l?exécution des travaux. La deuxième partie de la présentation est axée sur les résultats du programme de suivi en cours depuis la fin des travaux en 2001. Les éléments de suivi se rapportent à la baisse du niveau de la nappe phréatique à l?intérieur de la cellule, au tassement des résidus dans la cellule, aux mesures de température et d?oxygène à l?intérieur de la cellule et finalement à l?amélioration dans la qualité de l?eau de surface. ABSTRACT The reclamation of Poirier Mine, in Joutel, was carried out between 1998 and 2001. The main component of the works has been the reclamation of the tailings basin and tailings spill area which contained a total of 4,5 million tonnes of tailings and occupied some 74 hectares of ground surface. The mine tailings are highly acid-generating. The first part of the presentation will deal with a brief review of the reclamation plan followed by a short description of the main work components laying emphasis on experience gained during construction. The second part of the presentation will deal with the results obtained from the environmental monitoring program still in progress since the end of reclamation work in 2001. The aspects discussed include the drawdown of pore water inside the covered tailing pile, the settlement of mine waste material, the monitoring of moisture, temperature and oxygen underneath the liner and finally, the reduction of loadings in surface water.

Nov 1, 2002

By Willemijn Husslage

Tata Steel Group At a glance ? Part of the Tata Group ?Tata Steel Group: ?Fortune 500 company ?Top 10 global steel producer ?Annual crude steel capacity of 28 million tonnes ?More than 80,000 employees ?Manufacturing operations in 26 countries across 5 continents ?Serving customers all across the globe ?Turnover 2009-10: $22.8 billion

May 1, 2011

By K. Swedburg, M. Samuels

"The New Afton concentrator was commissioned in June 2012, reaching the design milling rate in September 2012. By late 2013, through a campaign of optimization and de-bottlenecking, it was recognized that the installed plant was capable of greatly exceeding the design throughput of 11,700 tpd. Because the value of the metal contained (by increasing the plant feed rate) exceeded the offsetting losses of copper and gold recovery (as the operation moved to a coarser grind), the concentrator feed rate was strategically increased with support of New Gold, while the operations team was given a mandate to evaluate, and then implement, flow sheet options that could re-establish the original design criterion grind target and achieve the corresponding improved recovery. Broadly, the two options implemented were the addition of a tertiary grinding stage consisting of Metso Vertimill® prior to rougher flotation (in order to address the grinding required at increasing throughput by increasing the power), and the addition of three Woodgrove Staged Flotation Reactors (SFR) added to the cleaner circuit after regrind of the rougher concentrate (to address the increased mineral loading to the cleaner circuit). Through test work, it was anticipated that the SFRs would be capable of achieving final concentrate grade in a single pass without the integration of recirculating loads, a strategy sometimes referred to pre-cleaning. This paper describes the expectations generated for the Woodgrove SFR unit operation through pilot plant testing on site, and compares those results with the performance of the expanded circuit that exceeded the original design criterion of P80 160 µm, which was commissioned in the second quarter of 2015.INTRODUCTIONThe New Afton concentrator, located near Kamloops, BC Canada, commenced operation in June 2012. The mill achieved the design throughput of 11,000 tonnes per day average during the month of September 2012 and, following various operational optimization efforts (O’Hara et al, 2015), achieved the design p80 grind size of 160 µm at the design milling rate in July 2013.During August 2013, trials were carried out to determine the throughput rate limits of the mill circuits and to evaluate mill metallurgical performance at higher rates. Milling rates up to 15,500 dmt per 24 hours were achieved during this trial, demonstrating potential capability for sustained milling rates exceeding the nominal design capacity. As was expected, the higher milling rates resulted in a coarsening of the grinding circuit product size, and resulted in marginally lower recoveries in the rougher flotation circuit. Despite the lower recoveries, the higher milling rates resulted in higher metal production and the financial analysis favored running at rates of at least 13,000 tonnes per operating day, with the higher cash flow in the near term offsetting the value of metal production loss at the end of the mine life (due to the short term increase in the rate of reserve depletion). Milling rates were sustained above 13,000 tonnes per day through the second half of 2013, and increased above 14,000 tonnes per day by mid-2014 (Figure 1)."

Jan 1, 2016

By Abhiram Shankar

Construction projects are becoming more demanding both in terms of time and complexity. This necessitates intricate planning and sequencing of activities at the macro and micro level and continuous flow of resources across the project in order to achieve planned targets. Work and Resource planning need to be done in such a way that limited resources give optimal output. Currently dominant activity-based scheduling techniques like Critical Path Method (CPM) and Program Evaluation and Review Technique (PERT) do not model work-flow or resource-flow through a project life cycle. An extension to the conventional activity based planning is Location Based Management System (LBMS). LBMS has been explored and utilised in the case of repetitive and cyclic projects such as high rise buildings. This study focusses on the application of LBMS to repetitive and non-repetitive components of Power Transmission and Distribution (PT&D) projects involving construction of substation and cable laying. This paper presents the findings on comparing the current planning practice for cable laying with an LBMS based approach. A key finding of the study was that the conventional practice resulted in a schedule with several coordination issues that could not be identified in the planning reports. Using the LBMS based approach these issues could be identified and decisions required for resolving these could be made.

Aug 1, 2013

By R. W. Lawrence, J. B. Austin, P. B. Marchant, J. T. Chapman

"Biohydrometallurgy is the use of microbiological reactions to assist in the extraction of metals. Bioleaching offers an innovative alternative for the treatment of refractory gold-bearing sulphides (1). One particular cost advantage of bioleaching is the potential to enhance gold extraction after only partial sulphide oxidation. The apparent selective sulphide oxidation is more prevalent where the refractory gold is associated with arsenic and antimony (2). Oxidation of the pyrite minerals and arsenopyrite at different oxidation rates can result in high gold extractions at relatively low levels of sulphide oxidation due to preferential, or selective, oxidation of the arsenic mineral. Arsenic extraction rates in a bioleach process typically exceed the iron extraction rate. Therefore, in concentrates in which the precious metals are principally associated with arsenic minerals, liberation of the precious metals may be possible with high recoveries and less than complete sulphide oxidation. The capital and operating cost advantages of partial sulphide oxidation are inherently obvious and are briefly illustrated herein.Ultra fine milling (UFM) is another alternative for enhancing gold extraction from refractory sulphides. Some refractory gold is simply particle size sensitive and UFM can improve gold extraction without the need for costly sulphide oxidation (3). Fine grinding technology for enhanced gold recovery developed by Metprotech, South Africa, is currently producing 2 - 4 micron ground product using a single pass, stirred ball mill. Proper application engineering has ensured that plug flow occurs through the mill. Plug flow from the feed inlet at the bottom of the reactor ensures that short circuiting of feed does not occur and as a result, the mill product does not require classification.A combination of UFM as a pretreatment for bioleaching could provide a mechanism for enhanced selective sulphide biooxidation and/or increased overall gold extraction following biooxidation due to improved particle liberation ( 4). The effect of UFM on biooxidation costs will be discussed. Only sulphide concentrates are considered herein for application of UFM in combination with biooxidation."

Jan 1, 1990

By R. A. Bergman, C. A. Pickles, J. M. Toguri

"Black calcium cyanide is utilized mainly as a reagent for gold extraction. It is produced by reacting calcium cyanamide, sodium chloride and calcium carbide at temperatures in the range of 1200°C to 1400°C in a smothered arc furnace. The equivalent sodium cyanide content of the product is in the range of 45% to 50% and the calcium cyanamide conversion efficiency is in the range of 90% to 95%. Since black cyanide contains impurities such as salt and lime and also because the conversion efficiencies are below 100%, the product contains unwanted materials which significantly increase the shipping costs.The impurity content of the raw materials can not be lowered without increasing their cost and/or the processes to produce them, and therefore the present research was focussed on studying those factors which affect the cyanide grade. The major variables investigated were: the heating rate, the reaction temperature, the salt to cyanamide ratio, the nitrogen content of the calcium cyanamide, moisture additions and calcium carbide additions. It was found that each of these variables had a significant effect on the product grade. The highest cyanide content of the product was obtained for salt to cyanamide mass ratios of 0.55 to 0.60. The salt reduces the decomposition rate of the cyanide and, therefore, at low salt to cyanamide ratios and at higher temperatures, the product grade is decreased. It is likely that the salt evaporates at the higher reaction temperatures and this decreases the cyanide capacity of the melt. High heating rates minimize the residence time and thus salt evaporation is reduced and higher grades can be obtained. As expected, the cyanide content increased with the nitrogen content of the cyanamide. Calcium carbide additions resulted in an increase in the product grade. The presence of small amounts of moisture in the charge caused a significant decrease in the cyanide content of the black cyanide. An equilibrium reaction is postulated in order to explain the black cyanide process and in particular the effect of calcium carbide on the product grade."

Jan 1, 2002

By Jay F. Colinet

Researchers at the Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) work to reduce respirable dust exposures in mining operations. One focus of this research is silica dust control for surface and underground operations in the metal/nonmetal mining industry. PRL researchers analyze dust sampling results from the Mine Safety and Health Administration (MSHA) to identify high-risk occupations to guide research efforts. Research is then conducted in an effort to improve existing technologies and/or develop new controls for reducing worker exposure to airborne silica dust. During the last few years, PRL researchers have conducted research related to the following goals: improving protection provided by enclosed cabs on mobile surface mining equipment, reducing dust generation from surface drills, reducing dust levels in iron ore operations, and developing a new method to clean dust from workers? soiled clothes. A description of each of these controls and subsequent dust reductions quantified through site surveys will be provided.

May 1, 2007

By D. Simon

This paper studies the effect of binder type and content on the early age development of cemented paste backfill (CPB). The early age development of the mixtures is analyzed using scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDX). These tests show that the early age development of CPB is sensitive to changes in the paste composition. The properties of the CPB depend on the cement content and hydration time. The quantity of hydration products increases with hydration time for all of the mixtures containing cement. However, the high cement content pastes (at least 50% PC) exhibit complete coverage of the PC grains and mine tailings by C-S-H, while the low cement content paste shows scattered coverage of the PC grains and mine tailings and a higher void ratio.

May 1, 2007

By Éric Poulin, Simon Gariépy, Mario Paredes Malca

"While the design of a control strategy depends on the available process knowledge, its implementation depends on the available process information. On-line chemical analyzers are today widely spread in the mineral processing industry. A real-time concentration measurement of chemical components is valuable information that could bring control strategies to whole new levels. However, the use of these measures rarely reaches anything more than process monitoring. The reason is simple: the on-line chemical measurements quality is most of the time insufficient to be directly included in control strategies. The choice is then made to let the critical eye of the engineer or the operator appreciates the measurements before making any decision based on it.Data reconciliation through mass balance is a technique today widely used in the mineral processing industry to increase the accuracy and the reliability of plant data, mainly for accounting and survey analysis purposes. Real-time data reconciliation of on-line measurements appears as a natural coupling of technologies that could bring new process optimization trends. Once overcome the technical difficulties, full valorization of the instrumentation investment could be reached.This paper presents the application of real-time data reconciliation for process control and performance monitoring. It proposes a general approach, discusses challenges and illustrates concepts with industry experiences."

Jan 1, 2006

A direct comparison has been undertaken between laboratory wind tunnel experimentation and computational fluid dynamics simulation of a 3D manufactured analogue for a body of fractured broken rock, created with CAD/CAM techniques. Detailed descriptions of the ?design? of the analogue (using a discrete element analysis multi-body simulator), its manufacture (using computer aided design and 3D printing technology) and the laboratory experimentation (inserting the physical analogue into a laboratory scale wind tunnel) are presented. The agreement of the results of direct experimental observations on the manufactured analogue with the values from CFD simulations of those experiments justifies the utilization of a CFD environment for the practical investigation of geometric factors controlling air flow and heat exchange in complex assemblages of broken rock blocks. The ultimate goal is described, that of developing functional relations between bulk properties of such assemblages (such as their porosity and bulk density) and the low-level geometric factors that dictate the air flow behaviour, such as the equivalent perimeter length of the cross-sectional area available for flow, or average flow path tortuosity. A practical application area of the work in the mining context is also described; equivalent continuum air flow and heat transfer constitutive models developed on the CFD tool from such functional relations are useful in characterization of seasonal heat storage in large scale bodies (approximately 1 km3) of broken rock.

Aug 1, 2013

By T. A. Grammatikopoulos, B. Vasily, A. H. Clark

"The St. Lawrence deposit is a large wollastonite skarn (ca. 9 Mt @ 41.3% wollastonite) adjoining the gabbroic-to-syenitic Leo Lake pluton in the granulite facies Frontenac Terrane of the Grenvillian Central Metasedimentary Belt. It occurs within a horseshoeshaped horizon of quartzite, open to the east. The skarn extends over 1.2 km2, and comprises wollastonite-dominant, wollastonite-clinopyroxene, and diverse quartz-feldspar-sulphide (-titanite) layers, interbanded with, and strongly folded within, the quartzite. As in the world-class wollastonite deposits of the Willsboro district, New York, no carbonate protolith is preserved, and calcite is a negligible constituent of the mineralized zones. Wollastonite development is nonetheless ascribed to metasomatism of a metacarbonate unit by magmatogene, silica-rich, CO2-poor (XCO2 < 0.05) fluids, at P = 350 MPa and ca. 560°C, or, alternatively, 550 MPa and ca. 630°C.Several high-grade zones, averaging >40% but locally exceeding 80%, of translucent, white, tabular wollastonite grains, with lengths of 0.2 cm to 5 cm, have been delimited by drilling. Preliminary beneficiation studies yield high aspect-ratio and high-purity (low Fe and Mn) concentrates.St. Lawrence compares favourably to other known prospects and operating wollastonite deposits: having good chemical and physical properties, low iron content, and high aspect ratios (>20:1). In addition, the deposit has a favourable size and location, and will benefit from a low Canadian dollar. Canada currently has no wollastonite production."

Jan 1, 2003

By J. A. Finch

"Much progress has been made over the last several years in the ability to measure flotation cell hydrodynamic parameters in both the laboratory and plant. These techniques have allowed fundamental research to proceed to determine the effects that frother chemistry has on the main hydrodynamic parameters (gas hold up, bubble size) as well as on the amount of froth generation and water content of froth. A research program was begun that brought together a team consisting of private companies and a University with expertise in hydrodynamic characterization (McGill), flotation reagent applications (Flottec) and chemical synthesis (Sasol N.A.) with the purpose of characterizing frother chemistries with two goals in mind: Determine which frother chemistry can provide optimized cell hydrodynamics; and, create new frother chemistries with specific hydrodynamic properties.This paper describes the key steps that were taken that led to the development of new frother chemistry for use in flotation.The first step was the characterization of the major frother chemical families in a two phase system. The parameters measured were gas hold up, bubble size, froth height and water carrying rate at different concentrations and gas velocities.Analysis of the data indicated that definite patterns existed between frother chemistry and hydrodynamics and showed that frothers could be grouped into classes. More importantly, by modifying known frothers through chemical reaction it was shown that these frothers could be moved from one class to another. As a result of this better understanding of the interdependence of hydrodynamic and chemical properties, a new frother chemistry was proposed that was predicted to perform similarly to MIBC.The new frother was synthesized and hydrodynamic testing confirmed that the chemical performed similar to MIBC. Laboratory flotation tests were conducted on two different ore types that also confirmed the similar performance of the new chemical and MIBC. Subsequently, the new product was placed on a plant for a short period of time. The results showed that the product was an excellent frother but increased the flotation rate slightly more than MIBC at the same addition rate.Further research showed that the new frother chemistry was a family of products. By changing the reaction the resultant products could be made to be slightly weaker or stronger than MIBC but that this chemistry cannot provide hydrodynamic/froth characteristics similar to strong frothers like glycols and glycol ethers. Further work is planned to conduct longer plant trials to confirm the efficacy of this new frother family."

Jan 1, 2007

By Martin Murenbeeld

Outlook: Nine Bullish Arguments 1. Global fiscal and monetary reflation: PIIGS, US, etc. 2. Global imbalances: the dollar must decline 3. Global FX reserves are ?excessive?: diversification 4. Central bank attitudes to gold: now positive 5. Gold is not in a bubble: room to rise 6. Mine supply is flat: ?peak? gold? 7. Investment demand: long-run uptrend 8. Commodity price cycle: many years to run 9. Geopolitical environment: positive

May 1, 2010

By W. K. Gowans

The Sullivan Concentrator treats a complex sulphide ore consisting mainly of galena, marmatite and pyrrhotite. The ore carried minor values in silver, antimony, bismuth, indium and tin. The products of the concentrator are lead, zinc, iron and tin concentrates. The minor metal values other than tin are recovered from the concentrates by the refining processes in the smelter at Trail.The concentrator was completed in 1923 and first operated with a capacity of 2,500 tons per day. In the years 1926 to 1929 changes to equipment and buildings brought the operation up to 5,500 tons per day and then, in the years 1935 to 1945, the daily tonnage was raised to 8,500 tons. After 1945, the rising insoluble content of the ore made it necessary to consider the construction of a Sink-Float plant. At this time consideration was also given to the construction of a new crushing plant underground to replace the rolls crushers and cone crushers located at the concentrator. By 1949, construction of the Sink-Float plant was completed along with a new underground crushing plant, and an electric haulage way between the underground crushing chamber and the Sink-Float plant. The ore was hauled in forty 14-ton car trains which discharged into a 3,000 ton receiving bin by means of an air operated five car rotary dumper. With the start up of the,Sink-Float plant, a 1 ½ ft. by 12 ft. Hardinge rod mill was also brought into operation. The Sink-Float plant made it possible to treat 12,000 tons/day of mine run ore with up to 40% of this being rejected as float.

Jan 1, 1975

By L. Vollert

In August 2018, the first full-scale HydroFloatTM cells for the recovery of coarse composited copper and gold were commissioned at Newcrest’s Cadia Valley operation in New South Wales, Australia. The primary objective of the installation is to recover coarse value-bearing composites that are lost to conventional flotation tailings, without the need for additional power input for particle size reduction to improve mineral liberation. This paper examines the application of Eriez HydroFloatTM technology for the recovery of coarse, poorly liberated copper sulphide particles drawing on recent experience from lab scale testwork through circuit design and commissioning of the full-scale installation at Cadia Valley. INTRODUCTION In the face of declining copper head grades and a tightening regulatory environment around the use of wet tailings dams, the processing of copper ores at coarser particle sizes has become a focal point for the industry. Sulphide flotation using the Eriez HydroFloatTM is one of the emergent technologies that sits under this umbrella of coarse pre-concentration. It has been demonstrated through numerous lab and pilot scale testwork programs carried out by Newcrest and others (Awatey, Kohmuench, Thanasekaran, Skinner & Zanin, 2013), to improve the flotation recovery of sulphide-rock composite particles with low surface liberation, relative to conventional flotation technology. The HydroFloatTM technology has been used widely for the recovery of coarse potash, phosphate, coal, vermiculite, spodumene and diamonds but has never been applied at full scale in either gold or sulphide flotation. In August 2018, the first full-scale 3.4 m diameter HydroFloatTM cells for the recovery of coarse composite copper and gold were commissioned at Newcrest’s Cadia Valley operation in New South Wales. The primary objective of the installation is to recover coarse value-bearing composite particles that are lost to conventional flotation tailings, without the need for additional upfront power input for particle size reduction to improve mineral liberation.

Jan 1, 2019

By E. LaRocque

"Denison Mines Limited has been processing uranium ore in the Elliot Lake area since May of 1957. The ore body is located i11 the Huronion sediments on the north limb of the Quirke Lake syncline. Minerals of metallurgical significance are brannerite, uraninite and monazite. Gangue minerals include quartz, chlorite, sericite, pyrite, pyrrhotite and rutile. Silica content of the ore is greater than 75 % and pyrite-pyrrhotite content around 7 %. Specific gravity of the ore is 2.75.The Denison flowsheet is based on sulphuric acid leaching to extract the uranium values from the ore followed by liquid-solid separation to wash the uranium-bearing solution from the barren ore. The resultant pregnant solution is concentrated and purified by ion exchange followed by two-stage precipitation with ammonia to produce an ammonium yellow-cake.Elliot Lake ores require high acid concentrations and high temperatures to extract the uranium from brannerite and monazite. Uraninite will leach at low acid concentrations as long as oxiclizing conditions exist. The whole ore must be treated so that these conditions do exist.This paper provides a description of the leaching process equipment as originally installed and major changes in that equipment to date. Process control refinements to economically improve extraction are also discussed."

Jan 1, 1979