Search Documents

By Joo Hyun Park, Hyun-Sik Park

"Gold is one of the most valuable and precious metals. But, the extraction efficiency of gold from natural resources is very low and labor-intensive due to very low concentration of gold, i.e.,1–5 ppm, which means that gold extraction processes produce extensive amounts of tailings. The gold content in printed circuit boards (PCB) from waste mobile phones is about 100 to 400 ppm, which is enormously greater than the concentration found in natural ores. Consequently, processes for recycling waste PCB and gold mine tailings become of increasing importance to maintain a sustainable society. As processing these waste materials by pyrometallurgical methods has become more economically attractive, understanding the thermodynamic behavior of gold in smelting slags under oxidizing and reducing conditions has become increasingly important. Therefore, in this study, the effects of slag chemistry, oxygen potential and temperature on gold solubility in smelting slags are discussed. From the results presented, the predominant species of gold is strongly dependent on the basicity of slag. Furthermore, more basic slags showed higher solubility of gold at a given oxygen partial pressure, and more oxidizing atmospheres enhanced the dissolution of gold to the molten slag phase. As a consequence, careful control of the slag composition during pyro-processing of gold-containing waste materials is required to maximize gold recovery. INTRODUCTIONGold has good physicochemical properties. Thus, it plays an increasingly important role in industrial applications. For example, over 300 tons of gold are used annually in electronic components (Hageluken &Corti, 2010).However, 75% of all gold ever produced has been extracted since 1910 and gold reserves in the world are becoming rapidly depleted (Louis & Pluchery, 2012).The cost of gold production and its price in the market have increased rapidly during last 20 years as shown in Figure 1, and interest in the recycling of gold-containing materials has naturally increased.The wastes from electronic equipment (e-wastes) contain large amounts of precious metals compared to their own respective ores, and therefore such wastes may be considered as a secondary source of valuable metals. For instance, the concentration of gold in natural ore is commonly 0.5–15 g/ton-ore (0.5–15 ppm), while its concentration in electronic circuit boards is over 10 times higher, typically being about 150 ppm in expansion cards and over 10,000 ppm in central processing units(Barbieri et al., 2010).Also, gold mine tailings are discharged after the flotation process as slurry form then stored near the operating plants (approx. 100 ton per day in one Korean gold mine). Gold mine tailings contain gold at about 1–2 g/ton. This is the reason why Au-containing materials such as e-wastes and mining wastes are highly important sources of gold (Yamasue et al., 2009)."

Jan 1, 2017

By J. H. Pee, Y. J. Kim, H. U. Lee, G. H. Kim

The general recycling process of tungsten scrap to produce tungsten raw materials (tungstic acid, ammonium paratungstate (APT) and WO3) have been carried out by the oxidation, milling, sodium-fusion, dissolution, and extraction processes. Many studies on the high temperature oxidation of tungsten scrap have investigated various aspects such as swelling kinetics, fracture resistance, and the effect of alloying composition. However, the accelerating factors on the scrap oxidation rate during oxidation were not considered here. In general, oxidized products were fused with sodium carbonate or sodium hydroxide to produce Na2WO4. Later in the process, solid Na2WO4 was dissolved in water. This process required considerable reaction time and was a costly process. Therefore, the aim of this study was to increase the solubility of solid oxidized products to produce Na2WO4 solution by hydrothermal reflux method. Na2WO4 solution was used to produce CaWO4 and H2WO4 by general chemical reactions with calcium chloride and hydrochloric acid. Ammonia solution was also added to the tungstic acid to produce APT. In this study, the effect of ammonia addition on the APT precipitation process was investigated in detail.

Jan 1, 2015

By I. Murray, N. Geoffroy

"Buried pipelines, tanks and other similar equipment are almost always present on large scale industrial sites, including in the oil and gas fields. However, as the proverb “out of sight, out of mind” suggests, it is easy to overlook proper maintenance procedures and simply assume that corrosion protection measures in place are working correctly. Unfortunately, this is not always the case, leading to significant environmental damage and loss of production. This paper describes several cases from various industries where buried equipment failed because of corrosion, sometimes with catastrophic results. It also presents various strategies, based on experience and new research, to help predict and prevent damage to underground metallic structures.INTRODUCTION Metallic underground structures are extremely common in industrial and commercial settings for numerous reasons. Burying pipes, tanks, wires and other similar equipment has numerous advantages: it provides significant protection from mechanical damage, frees up ground space that can be used for other purposes, requires little to no support structure and is generally more esthetically pleasing. However, this last benefit can also be considered the most significant disadvantage of underground equipment: becoming invisible and forgotten. While every engineer is aware of the importance of preventive maintenance, it is also human nature to somewhat forget about equipment that is hard to inspect and assume that everything is fine. This is unfortunately not always the case and failures in industrial settings can have extremely serious consequences. While economic aspects immediately come to mind (loss of production, cleanup cost, etc.), failure of underground equipment also results in an environmental and therefore public relations nightmare, especially in the oil and gas field. Leaks that would have been considered negligible in the past can now make national headlines and perfect reliability, while probably impossible to achieve, is now the goal of most companies. While environmental damage (real or perceived) is most often associated with leaks in the oil and gas industry, it can also affect the mining world. For example, the authors have worked on a project where a buried slurry pipeline had ruptured in the ground, causing a release of perfectly inert tailings. While the economic loss was low, the leak was reported in local media and caused a public relations problem."

Jan 1, 2017

By Michael Moser, Brighty Dutta, David Dreisinger

"Molybdenum is widely used in the industries as an alloying element in the manufacture of steels and super alloys. The widespread use of the element encourages a growing need to develop extraction processes for recovery from both primary and secondary sources. The Solvay Group has developed a solvent extraction reagent named CYANEX®600 for the recovery of molybdenum from acidic solutions originating from both low grade (e.g. copper solvent extraction raffinates, smelter dusts and slags) and high grade (molybdenite) molybdenum sources. CYANEX®600 is a purified form of CYANEX®272 with the active component bis(2,4,4- trimethylpentyl)phosphinic acid. The extraction behavior of CYANEX®600 towards molybdenum in sulphuric acid medium was evaluated. The uptake of molybdenum increased with the increase in concentration of CYANEX®600. The approximate stoichiometry of the extracted complex was: Mo: CYANEX®600 = 1:2. Efficient back-extraction could be achieved with 0.1 M disodium EDTA and 0.1 M (NH4)2CO3, thus providing the option of recyclability of the extractant. The detailed back-extraction studies are currently under progress to find out the possible option for complete transfer of Mo(VI) to the aqueous phase so that high purity Mo salts could be precipitated from the molybdate solutions.INTRODUCTION Molybdenum (Mo) is one of the world’s valuable metals and is highly sought after by researchers due to its versatile mechanical, thermal, chemical properties. Swedish scientist Carl Wilhelm Scheele demonstrated molybdenite to be a mineral sulfide in 1778. Peter Hjelm successfully isolated dark metal powder from the mineral sulphide and named it as ‘Molybdenum’ in 1782 (Gupta, 1992). Molybdenum is a refractory metal of silver gray appearance and is an important alloying element used in the manufacture of steels and super alloys. Molybdenum compounds are widely used in formulation of catalysts (Gupta, 1992). Molybdenum occurs in nature only in chemical combination with other elements. Several molybdenum bearing minerals have been identified, but the only one of commercial significance is molybdenite (MoS2). As molybdenum is a strategic metal for the industrial sector, its widespread use acts as a factor for depletion of the natural resources. Hence, there is growing need to develop extraction procedures for its recovery from both primary and secondary sources. United States, China, Chile, Canada, Peru, and Mexico are listed as the main producers by the U.S. Geological Survey, 2016 (U.S. Geological Survey, Mineral Commodity Summaries, January 2016)."

Jan 1, 2017

By X. Zhou

"Hydrogen induced failure and degradation in structural metals, namely hydrogen embrittlement, has been a long-standing industrial problem for more than one century and remains unsolved. Despite the proposal of numerous models, no consensus has been reached, and considerable discrepancies in experimental observations and theoretical calculations exist. One aspect that is central to the understanding of hydrogen embrittlement is the interaction between hydrogen and grain boundaries. In this study, we investigated the influence of several solute elements (i.e., Cr, Mo and Nb) on hydrogen segregation at the representative 9 grain boundary using first-principles calculations. Our results showed that the presence of Mo and Nb can reduce the tendency of hydrogen segregation at grain boundaries, while meanwhile enhance the grain boundary strength. This indicates that Mo and Nb are salutary elements that can be used to increase the material’s resistance to hydrogen embrittlement, providing new insights in designing hydrogen embrittlement resistant Ni alloys. INTRODUCTION Hydrogen embrittlement (HE), a phenomenon of hydrogen triggering premature failures in structural metals, has been a headache for industries ever since its first discovery one century ago (Johnson, 1874; Zhou, Marchand, McDowell, Zhu, & Song, 2016; Zhou, Ouyang, Curtin, & Song, 2016). It is well accepted that the segregation of hydrogen at microstructures such as grain boundaries (GBs) plays a key role in determining the occurrence and severity of HE. GBs are two-dimensional defects where significant local lattice distortion exist, which leads to large free volume and thus locations for hydrogen trapping and segregation. Numerous works have clarified GBs as the energetically preferable places for hydrogen segregation. For instance, Geng et al. demonstrated the preferential segregation of hydrogen at the S5(120) GB in several metals, and suggested a decohesion-type of HE in light of Rice-Wang thermodynamic theory (Geng, Freeman, & Olson, 2001). Birnbaum et al. illustrated that complete intergranular crack of Ni GBs can be induced by hydrogen segregation when the hydrogen concentration is sufficiently high, evidencing the significant role of hydrogen accumulation on GB weakening (Lassila & Birnbaum, 1987). Yamaguchi et al. demonstrated strong segregation hydrogen also occurs at S3 GBs in alpha-iron, showing that local hydrogen clustering (i.e., multiple hydrogen atoms, up to six, per unit cell) can be trapped at the S3 GB (Yamaguchi, Kameda, Ebihara, Itakura, & Kaburaki, 2012)."

Jan 1, 2017

By S. Khallouk, J. Zollinger, J. R. Kennedy, E. Bouzy, B. Rouat, D. Daloz

Titanium aluminides recently replaced Ni-based superalloys as turbine blades in the last LP stage of aircraft engines. To extend their range of use at higher temperature their properties need to be improved, either by alloying or processing. An efficient solution is to reduce the grain size during the solidification process. In the first part of the paper, an overview is given on the possibilities for grain refinement of such alloys, based on literature data and new results. The most efficient grain refinement is obtained with boron addition which leads to boride formations that are detrimental for in-use properties of turbine blades. In this work, the use of the high grain refinement potency of inoculation with non-brittle particles has been used by developing new refractory-based inoculants. The effect of one of these inoculants on grain refinement of an as-cast structure in a Ti-46Al is presented; resulting in a reduction of the grain size by a factor of 3.While less efficient compared to the potency of boron containing alloys, the grain refinement is effective and does not introduce any embrittling particles.

Jan 1, 2015

By Seong-Ho Ha, Shae K. Kim, Young-Ok Yoon

In the this study, surface segregation of Mg and Ca with Mg addition range from 5 to 10wt% in Al-Mg alloys with Mg+Al2Ca master alloy and its effect on the oxidation resistance were investigated. The addition of Mg+Al2Ca master alloy as the Mg alloying element led to the surface enrichment of Mg and Ca during high temperature oxidation. As a result of the oxidation test by TGA, the oxidation resistance of all the examined alloys was significantly improved with increasing Al2Ca content. The weight change of Al2Ca added Al-5Mg and Al-7.5Mg alloys indicated the complete oxidation resistance during the whole oxidation test time, while a slight weight increase was shown in the case of Al-Mg alloys even with Al2Ca addition. The improvement of the oxidation resistance in Al2Ca added alloys may be attributed to the formation of the protective oxide layer mixed with CaO and MgO on the surface.

Jan 1, 2015

"Real-time, on-stream analysis of the metal content of process slurries is an essential prerequisite for process monitoring and advanced control of mineral processing circuits. On-stream X-Ray Fluorescence (XRF) sensors for base metal applications are available commercially and form the basis of many plant monitoring circuits. To date, these commercial technologies have been insufficiently sensitive to measure precious metals such as gold and platinum group elements, typically present at part-per-million (ppm) and sub ppm levels. CSIRO has developed a novel X-ray based technology, called UltraGold, which enables detection of gold in slurries on a real-time basis with a precision below 100 parts-per-billion. This technology is based on the use of advanced X-ray optics, extensive Monte Carlo computer modelling for analyser design, high accuracy X-ray spectrum fitting where the X-ray intensities are matrix corrected. In this paper, we will introduce this technology and discuss the results of a proof of principle study performed in the laboratory with plant slurries (tailings and concentrate) from an Australian beneficiation plant. Finally, we will discuss further planned improvements. As projected grades in (gold) mining around the world fall and several large-scale mines approach the limits of their economic reserves, this method can enable significantly reduced operating costs by rapid analysis to improve circuit efficiency and hence improve recovery significantly.INTRODUCTION This paper describes a study undertaken to explore the feasibility of applying CSIRO?s UltraGold XRF technology to the on-stream measurement of gold in process slurries. The provision of rapid, accurate information of gold grade in feed, tailings and concentrate streams would facilitate significantly improved process control and early detection of plant upsets, resulting in substantial cost-savings. CSIRO have patented X-ray fluorescence (XRF) techniques for the analysis of key elements in slurries present at part-per-million (ppm) and sub-ppm levels. Conventional, commercially available on-stream XRF instruments generally have detection limits in the tens of ppm range, precluding their use for analysis of elements like gold that are mined and processed at much lower concentrations."

Jan 1, 2017

By J. E. Reeves, J H. Morgan

Certain non-metallic minerals are used widely as fillers in the manufacture of many Canadian products. The first part of this paper deals in a general way with deposits of such minerals and their mining, with the concentration and preparation of the minerals for market, with specifications of the consumers, and with methods of control of the products to meet the specifications. The second part of the paper de-scribes talc as a specific example of mineral filler. Its production and uses in Canada and the possibility of producing higher grades of talc are discussed. Some suggestions are made for meeting the needs for mineral fillers as Canada's industry expands. RELATIVELY few people are sufficiently aware of the vast and important role that is being played in our everyday lives by mineral fillers. Many kinds of paints, papers and plastics, to mention three major classes of industrial products, are literally loaded

Jan 1, 1961

By Eduardo R. Rodrigues, Ankur Narang, Roberto Federico Ausas, U. T. Mello, Jose Maria Segura Serra, M. R. Lakshmikantha, Ignacio Carol, Kamal C. Das

"Modeling of big faults or weak planes of strong and weak discontinuities is of major importance to assess the Geomechanical behaviour of mining/civil tunnel, reservoirs etc. For modelling fractures in Geomechanics, prior art has been limited to Interface Elements which suffer from numerical instability and where faults are required to be aligned with element edges. In this paper, we consider comparative study on finite elements for capturing strong discontinuities by means of elemental (EFEM) and nodal enrichments (XFEM) for Geomechanical applications. For general fracture scenarios, Oliver et al. (2008) have demonstrated advantages of EFEM over XFEM for including: (a) ease of modeling in any standard finite element code due to the possibility of static condensation, (b) higher accuracy in some cases for coarse meshes, and, (c) a reduced computational cost. However, there has been no work that considers cohesive fractures in Geomechanics. We present a numerical analysis based on a linear constitutive model and linear triangular elements for the bulk and a linear constitutive behaviour for the fault for a representative set of fault planes in a circular tunnel made in rock mass. In the numerical examples we consider both well-traced and bad-traced meshes. We focus on traction profile analysis for both EFEM and XFEM, since that is crucial to understand the cohesive fracture behaviour specially rock joint. Therefore in each case, shear, normal and stress ratio are compared across the two methods along the fault plane. This is the first such work that compares XFEM and EFEM behaviour for Geomechanics problems.For the considered class of problems and the sharp penalization approach without regularizations adopted, it can be observed that accuracy and robustness of EFEM may strongly depend on the fault orientation with respect to the element edges, while, XFEM is independent of fault alignment with element edges. It has been also observed that, with mesh refinement model, stress oscillation completely removed with XFEM however EFEM fails to provide oscillation free results with finer mesh in case bad-traced model. We also performed error analysis and found that in case of bad-traced mesh the average error in the XFEM is 84% smaller than of EFEM and for XFEM the error goes to zero with increasing mesh resolution, while for EFEM the error increases with mesh resolution. Thus, we experimentally demonstrate that, XFEM performs better than EFEM in terms of accuracy and rate of convergence with marginal increase in computational cost. This work hence provides novel insights on the application of XFEM and EFEM in Geomechanics."

Jan 1, 2015

By G. E. Peacock

SIGMA MINES is situated in the township of Bourlamaque, Abitibi County, Quebec. It is a gold producer, and presently treats an average of 1,200 tons of ore per day, at a grade of approximately 0.18 oz. per ton recovered. The mill started operations in March, I937, at a rate of 300 tons per day. This was increased to 800 tons in I940, and to 1,000 tons by I943. The rate was cut back during the war years, but was brought back up to capacity by I948. The mill tonnage was in-creased to the present 1,200 tons per day in I960. The underground workings are serviced through No. 2 Shaft (Figure 1), which, with 24 operating levels, extends from surface to a depth of 3,317 feet. When depth exploration was decided upon, two possibilities were considered: (a) deepen the main shaft by1,000 feet; (b) put down a winze for the same distance.

Jan 1, 1962

By J. B. Edwards

"The case is presented for the use of simulators for the computer-based training (CBT) of mining plant operators and for introducing them to automatically controlled systems. As well as their use in the classroom, the role of simulators is examined for ""on-plant"" use in trouble-shooting, fault-finding and maintenance of automatic systems. Case studies are presented showing how specific simulators are becoming established or have potential in the areas of automated materials handling, machine testing, setup and guidance. The evolution of scientific simulations into simulators of widespread practical use is discussed and present-day limitations of computer speed and graphics are considered. Related areas of research for the Canadian Centre for Automation and Robotics in Mining (CCARM) are identified.IntroductionCCARM's Commitment to Simulator DevelopmentAs automation is progressively developed and exploited in mining operations, there arises an urgent need to educate and train staff responsible for its introduction and operation in our mines and for its maintenance. For this purpose , an essential ingredient of an automation program is the development of appropriate mining system simulators for use by a wide variety of personnel. The author has been fortunate to have been closely involved with the development of automatic control systems for a variety of mining machines and mining systems in the United Kingdom. A key ingredient of the research phase in each case has been the use of simulation techniques. As projects have moved toward their commissioning and exploitation phase, the simulations have evolved into simulators tailored for use by machine operators and maintenance personnel. Illustrative case studies are presented later. The researach of the newly constituted Canadian Centre for Automation and Robotics in Mining (CCARM) will likewise involve extensive simulation, and the development of simulators (from the scientific programs) for use at the mine by operators and technicians will be given high priority in the Centre's over-all work program."

Jan 1, 1990

By Trent Hamilton

Cameco ? McArthur River Operation is a high-grade uranium mine in northern Saskatchewan. Average grades mined are nearly 20%, more than 20 times higher than other operating uranium mines in the world. The significant risks involved with mining this grade has been effectively mitigated using innovative and unique controls, implemented from development and production mining through to ore processing. The types and sources of radiation are presented and protection measures are discussed. McArthur River?s strong radiation culture is evidenced by continually low radiation exposures while transitioning to new mining zones.

Aug 1, 2010

By David M. Knowles, R. Gordon Gastil

"The Precambrian sedimentary series of the Labrador geosyncline, including iron formation, extends into southwestern Labrador and adjacent Quebec. The iron formation consisted of primary oxide, silicate, and carbonate facies which were deposited simultaneously in an irregular basin in response to migratory environmental conditions. The iron formation isochemically recrystallized to coarse-grained quartz-iron oxide, iron silicate, and quartz-iron carbon-ate rocks during prolonged regional metamorphism. The rocks are deformed on two deformation axes intersecting at large angles, and are characterized by isoclinal to recumbent folds. Parts of the formation have been profoundly affected by a post-metamorphic leaching and oxidizing environment."

Jan 1, 1959

By K. L. Azinger

Successful relationships between mining companies and local stakeholders are now an essential part of the social contract of “doing business” (Prescott, 1995). The methodology presented in this paper is designed to assist mining companies in understanding and building relationships with diverse stakeholder groups. The methodology starts by recognizing that mining projects have a natural life cycle which can be used to identify when new external affairs strategies are required. In designing an external affairs strategy, the first step is to set objectives that are compatible with the overall objectives of the mining project. The management team then identifies the main stakeholder groups and seeks to understand the priorities and inter-relationships of the individual stakeholders. The result of this stakeholder analysis is an understanding of the Degrees of Influence of each of the stakeholder groups along with a relationship map which illustrates the strong interactions between stakeholders. The company is then prepared to take a proactive approach to building relationships with the primary stakeholders. This methodology was developed by BHP to assist with the federal government environmental approval process for the development of Canada’s first diamond mine. BHP has successfully used the methodology in three different phases of the NWT Diamonds Project and is now applying the methodology to mining and development projects around the world.

Jan 1, 1998

By J. S. Kirkaldy, W. J. Slater, G. R. Mason

Activation analysis for copper and manganese in 10 mg samples machined from aluminum-base diffusion couples has been used in the study of ternary diffusion in the Al-Cu-Mn system. The accuracy, economy and convenience of the method are considered to be very competitive with other methods for analysis of such small samples. Neutron-activated aluminum-zinc alloys in the range from 10 per cent to 100 per cent zinc have been equilibrated with a known volume and the vapors subsequently condensed and collected. The vapor pressures relative to pure zinc (the thermodynamic activities) have been determined at 550°C' by recording the relative count of /'-rays from zn65 in the collected samples. The method is a sensitive one, although subject to serious obstacles to experimental accuracy.

Jan 1, 1961

By M. Nakai, G. Itoh, R. Yamada, A. Kurumada

In order elucidate the mechanism for poorer fatigue properties of 7000 series aluminum alloys than those of 2000 series alloys, the effect of the test environment on the fatigue crack growth of the two series alloys was investigated, considering the relationship to hydrogen embrittlement. Two 7075-type and four 2024-type alloys were T6-tempered and T4-tempered respectively, and subjected to fatigue crack growth tests in moist and dry environments. When tested in moist air, fraction of intergranular crack path was higher in the 7075-type alloy with coarse equi-axed grains than in the 2024-type alloy with similar microstructure. This was in accord with the larger crack growth rate in the 7075-type alloy. Both the intergranular crack path fraction and the crack growth rate were decreased by changing the environment to the flow of nitrogen gas. Thus, the large fatigue crack growth rate of the 7075-type alloy is attributable to hydrogen embrittlement.

Jan 1, 2015

By K. B. Young

Possibly the most complex fatigue problem associated with the development of the axial-flow 'gas turbine is discussed in its broader aspects from the metallurgical viewpoint. Reference is made to nodal patterns, interference diagrams, etc. The use of such data in analysis of a turbine :blade failure is illustrated. Special attention is given to the influence of some metallurgical variables affecting fatigue strength and, in particular, heat treatment is shown to have a pronounced effect on .the relative fatigue and creep strength properties of a nickel-chromium-cobalt base alloy suitable for turbine blade applications.

Jan 1, 1958

By O. A. Ojo, E. Anisimov, A. K. Khan

Electro-spark deposition (ESD) has recently generated a great deal of interest in processing aerospace materials. This is due to its potential for joining and repairing difficult-to-weld precipitation strengthened nickel-based superalloys without having problems of welding cracking that often plaque these materials. The short duration of current pulses involved in the process combined with the intermittent contact results in extremely rapid thermal cycle that produces nearly no heat affected zone in the substrate material. The microstructure of electro-spark deposited superalloy was meticulously studied in this work by scanning electron microscopy (SEM) and analytical transmission electron microscopy (TEM). The results show that in contrast to general assumption, the extreme rapid cooling rates involved in the ESD process did not produce partition-less solidification that is devoid of second phase microconstituents in the material. The secondary microconstituents were found formed along the intercellular regions of the solidification microstructure. The nature of these particles and the possible implication of their formation on mechanical properties of ESD processed material are reported and discussed.

Jan 1, 2015

By Yun-Soo Lee, Su-Hyeon Kim, Hyoung-Wook Kim, Joon-Hyeon Cha

A7075 aluminum alloys have high strengths but poor corrosion resistance. In order to improve the corrosion resistance, a clad sheet is suggested, that is the A7075 alloy sheet bonded to A1XXX or A6XXX aluminum alloy sheets which are surface layers with good corrosion resistance. Mechanical properties of the clad sheets are determined by the combination of the component layer sheets, and thermomechanical treatment should be precisely designed when the strengthening methods of the core and the surface alloys are quite different. In the present study, three-layered A6022/A7075/A6022 clad sheets were fabricated by roll bonding process. Simplified processes incorporating a twin roll casting were also suggested in order to reduce the processing cost. Several temper methods composed of rolling, annealing, solution treatment, and aging were suggested in order to optimize the mechanical properties of the sheets. The strengths of the clad sheets were compared with the bare A7075 and bare A6022 sheets.

Jan 1, 2015