Search Documents

By T. W. Wlodek, Zygmunt Kowalczyk

In the period from 1946 to 1964, the annual output of co al from Polish mines increased from 4 7.3 to 117.35 million tons. In this paper, the methods of bringing about this increase in productivity through the building of some twelve new collieries (producing some 15 million tons annually) and the modernization, reconstruction and extension of some thirty-six older collieries are discussed.

Jan 1, 1967

By G. S. Hume

Introduction O WING to the mineral discoveries which have recently been made in the Great Bear Lake region and the possibility of the need for fuel for transportation and development, it seems.timely ro review available information regarding the oil prospects in the vicinity of Great Slave lake and Mackenzie river, where a vast area is underlain by Palreozoic and younger sediments that undoubtedly are petroliferous. Exploratory surveys were carried out in this area by the Geological Survey and others in the latter part of the 19th century, but it was not until 1920, when drilling for oil actually began, that any serious attention was paid to the oil prospects. This is readily accounted for by the remoteness of the region, the lack of quick transportation facilities, and the shore summer season. Numerous and copious oil seepages had been reported, however, from widely separated localities, and interest was stimulated by the knowledge that these occurred in Devonian strata which had given a remarkable record of sustained production of high-grade oil in the oil-fields of southwestern Ontario. . Accordingly, during the four years 1920 to 1923, inclusive, several parties sent out by the Geological Survey made as thorough an investigation of various parts of the area as seemed warranted at that time, and from these surveys most of our information regarding the details of the stratigraphy is derived. In such a large area, it is inevitable that the lithology and thickness of rocks of the same age would show wide variations, and hence it should be recognized that conditions as regards oil prospects in the vicinity of the west end of Great Slave lake are quite distinct from those that occur near Fort Norman, 400 miles farther to the northwest, and these again are in all probability quite different from those in the less well known Arctic Red River area, 250 to 300 miles still farther north.

Jan 1, 1932

By D. A. Beattie

Talc is a commonly encountered gangue mineral in metal sulfide flotation. Talc is naturally hydrophobic, resulting in high recoveries if polymeric depressants are not used to specifically reject this MgO containing mineral. We have studied the adsorption of a selection of polymers onto talc using a variety of techniques. Adsorption isotherms have been determined using ex situ depletion techniques and in situ ATR-FTIR spectroscopy has been used to determine adsorption kinetics. Adsorbed layer thicknesses have been determined for the polymers on cleaved talc surfaces using the AFM. The effect of the adsorbed polymer layer on the properties of the talc surface has been quantified through contact angle measurements and single mineral flotation tests. Distinct correlations are observed between the adsorbed layer properties and the flotation performance of the polymers. These observations are discussed with reference to the bubble-particle attachment process and the molecular structure of the polymers.

Jan 1, 2006

By C. Grisanti, E. Prina Howald

The major of Swiss territory is occupied by mountains. Natural events as floods, debris flows, landslides, rockfalls, and avalanches regularly threaten the safety of people and properties. On the one hand, extreme weather events cause great damages, on the other hand, the enhancement of territory’s exploitation increases the risk. The Swiss Government makes many efforts to deal with the prevention of natural hazards, especially through measures of land management. As stated by federal law, Swiss cantons are obliged to establish hazard maps and to take the risk into account in the land management. Hazard maps are based on the hazard matrix, whose abscissa and ordinate are probability and intensity of the event on site. This project focuses on rockfalls. It consists of three main parts: the creation of a database to collect data on site, the creation of a catalog with all type of measures, and the development of a methodology for the analysis of the effectiveness of protective measures. The creation of the database allows us to collect information: about the site, about protective structures implemented on it, and about failures. With many multiple choice fields and few free text fields, it can collect data in a homogeneous way, without redundancy. The catalog has to be a tool that gives a basis to make decisions. It collects information about all types of protective measures implemented on Canton Vaud’s territory or available on the Swiss market. Free text fields allow for data storage of specifics, to give a complete view of structure’s characteristics and potentials. Methodology consists of four steps. The core of the procedure is the structure’s evaluation following a score system; it allows for calculation of reduction factors that have to be applied to intensity and probability parameters of the structure. Then it is necessary to convert the reduced structure’s intensity value into a residual site’s intensity value. Although the first step enables us to choose suitable measure for a specific site, it is not necessary to perform it. Second step allows us to evaluate structures under scenario 0, where structures are in best conditions. Third step allows us to evaluate structures under six scenarios of possible failings. Fourth step allows us to convert structure’s reduced intensity into event’s residual intensity and to establish the new point on hazard matrix. While the procedure has already been defined, details of score system and conversion have to be developed during the second phase of the project.

Jan 1, 2015

By G. A. Vissac

IN THE preliminary design of a coal washery, the most important factor to evaluate is the ash content of the final product. The ash content permissible may be imposed by market demands, but, in the final analysis, sooner or later - as most consumers today are buying coal on a 'heat value' basis - the coal operator has a certain margin of latitude. and the ash content of the coal to be delivered can be determined on the basis of maximum returns and highest profits. A few years ago, the most desirable separation was selected on the basis of the plus-minus 0.10; that is, the most desirable gravity of the separation was selected at the point showing a minimum amount of near gravities in the raw coal. The reason for this was an expected wide error over these near gravities. Today with the recent development of cry accurate, automatically controlled cleaning apparatus, a much larger latitude is possible, and the most desirable gravity of separation can be selected, almost exclusively, on the basis of the economic factors involved. To illustrate these new methods of investigation we shall give two examples, based on actual coals from the western United States.

Jan 1, 1957

By Z. Huda

The effect of various percentages of cold-working and recrystallization on the microstructure and hardness of commercially-pure aluminum plate, has been studied. The 'A critical deformation for the aluminum, has been determined. Experimentation involved cold rolling and recrystallization processes followed by quantitative metallographic practice and the hardness measurements. The raw material chosen was a plate of commercial aluminum which was cold rolled to different percentage of cold-work and then recrystallized by heat treatment at 150°C. The critical deformation percentage of aluminum was computed to be around 30% of cold-worked.

Jan 1, 2007

By David J. Forrester

"CANMET’s research into underground coal mining is primarily conducted at the Cape Breton Coal Research Laboratory (CBCRL), established in 1981 to conduct safety research in underground coal mines. Located close to Canada’s largest underground coal producer, in the Sydney Coalfield of Nova Scotia, CBCRL’s program also includes the two western underground coal operations. CBCRL is a relatively small laboratory with a staff of thirteen — eight professionals and five support staff — with an annual budget of over $1 million. In order to maintain effective research response, flexibility is key and staff are increasingly working in project teams, crossing traditional section ties and also drawing from specialist expertise elsewhere within CANMET.CBCRL’s research activities have had a substantial impact on the Canadian underground coal mining industry, particularly in Cape Breton. CBCRL contributed to Cape Breton Development Corporation’s (CBDC’s) threefold reduction in lost-time accidents in the 1980s. Also, in the last four years alone, CBCRL’s work has enabled CBDC to save over $17 million in improved utilisation of reserves and cost savings. The work embraces the three traditional areas of mine environment, strata mechanics and mining technologies, however the current direction has been strongly influenced by recent external and internal factors. It is timely to review progress and recent directions."

Jan 1, 1996

By J. Oyunaa, P. Munkhbaatar, A. Sarnai

"The molybdenum mining process used at Mongolia Erdenet Company is a selective flotation of molybdenite from the copper porphyry ores in which the extraction of molybdenum comes as a byproduct of the ongoing copper production.The mineralogical composition of molybdenum concentrate is 99.4% molybdenite (MoS2), 0.09% molybdenum oxide (MoO3), 0.52% powellite (CaMoO4) and wulfenite (PbMoO4) and content 47.76– 47.92% molybdenum, 1.5–2.67% copper, 0.04% renium.From compared solvents sodium and carbonate and ammonia are like extracted molybdenum than hydrochloric acid, which contained 96.23–97.72 p.c. of its total amount. Hence to take into consideration abundance, cheap and suitable for analysis and processing the molybdenum concentrate ammonia is choosing as a basic solvent. By direct evaporation of ammonia extract solution, we obtained ammonium ortomolybdate, which contains 73.47% MoO3. INTRODUCTIONMolybdenum occurs in the earth’s crust in an abundance of about 10–14%, mainly as molybdenite, MoS2. Small quantities are also associated with other metals having similar chemical properties. Thus wulfenite (PbMoO4) is found in oxidized parts of sulfidic lead deposits in many regions of the world; powellite [Ca(Mo,W)O4] is a calcium molybdate usually formed from the modification of molybdenite in deposits containing tungsten as scheelite (CaWO4) and tungsten substitutes for molybdenum up to about 10%. Ferrimolybdite (Fe2Mo3O12·8H2O) is the product of oxidation of molybdenite in the presence of iron (III) compounds. Molybdenite is the primary source of molybdenum. Should demand for molybdenum rise so that additional sources become necessary, wulfenite, powellite, and ferrimolybdite may become commercially significant. Molybdenum ore is mined by underground and open-pit methods. A typical primary molybdenum ore body contains 0.05–0.25% Mo, and secondary ore bodies (copper porphyry ores) average 0.3–1.6% Cu and 0.01–0.05% Mo. Flotation remains the preferred and almost exclusive method of upgrading the molybdenite mineral to an industrial-grade molybdenite concentrate containing 90–95% MoS2, the balance being gangue (Habashi, 1997)."

Jan 1, 2016

By Dean Millar

Clean, green, cheap compressed air can be produced efficiently and renewably by modernization of a 19th century technology ?The hydraulic air compressor has no moving parts ?After commissioning, the Ragged Chutes HAC operated for 70 years, only being stopped twice for repairs to the intake heads ?Operates using hydropower from Montreal river ?Produced air for ~29 silver mines in Cobalt, 20 km distant

May 1, 2013

By Chris McBean

Due diligence mistakes ? lost opportunity ? High profile write-downs and cost overruns ? Result ? tight market for financing ? Implications for due diligence ? need to get it right ? maybe only one chance ? Where should focus be?

May 1, 2013

By L. M. Guayacán-Carrillo, G. Armand, A. Noiret, D. Seyedi, S. Ghabezloo, J. Sulem

"The main purpose of this paper is to analyze the convergence measurements in a drift excavated in the Callovo-Oxfordian claystone. The drift axis is in the direction of the major principal horizontal stress whereas the stress state is quasi-isotropic in the drift’s section. The initial geometry of the drift being circular, the anisotropic character of the deformation is taken into account by assuming that the drift shape evolves in an elliptical shape. The convergence measurement data on six different points around the drift are analyzed to identify the main axes of the deformation ellipse, following the methodology proposed by Vu et al. (2013, Rock Mech Rock Eng, 46, 231-246). Then, using the semi-empirical law proposed by Sulem et al. (1987, Int J Rock Mech Min Sci, 24, 145–154), the convergence evolution is fitted independently for each axis of the ellipse. This method permits to distinguish two effects: the face advance effect and the time-dependent behavior of the ground. The results for the two directions of the ellipse axes show very close values for the parameters describing the time-dependent properties of the ground, the distance of influence of the face, and the extension of the decompressed zone around the gallery. Such model can provide valuable insights for predictions of the convergence evolution in the long-term. INTRODUCTIONDeep disposal of radioactive waste has been studied in France for more than two decades. The French National Radioactive Waste Management Agency (Andra) began in 2000 the construction of an Underground Research Laboratory (URL) with the main goal of demonstrating the feasibility of a geological repository in Callovo-Oxfordian claystone. Several research programs have taken place to improve the knowledge of the rock properties and its response to the excavation progress. The optimization of supports design for long-term behavior is an important point to develop. A network of experimental drifts has been constructed with variations on: excavation method, structure geometry, supports system and orientations with respect to in-situ principal stresses’ directions. In each drift different sections have been instrumented to monitor the convergence evolution and the rock deformation. Continuous monitoring of the excavated zone around the drifts revealed the development of a fractured zone (extensional and shear fractures) induced by the excavation. The extent of this fractured zone depends on both the drift orientation and the in-situ stress field (Armand et al., 2014). Indeed, the fractures distribution has an important influence on the convergence of the drifts."

Jan 1, 2015

By C. Moctezuma

Since the start up of the IMMSA electrolytic zinc refinery in 1982, the dissolved iron coming from the acid attack of the ferrites has been precipitated by the jarosite process. At the beginning of operations, sodium jarosite was produced; however, the plant was converted to ammonium jarosite in 1990. The final storage of the residue is on the company&apos;s property adjacent to the plant, over the natural surface of the land. Before the construction of the refinery, several studies were done in order to evaluate the characteristics of the ground, such as, permeability, underground water localization, etc. The results showed that the site was adequate for the storage of this kind of material. For several years, the jarosite residue was filtered on rotary drum filters and was sent as a pulp to the storage area for settling. The water from the storage pond was recycled to the re-pulp tank for the jarosite residue. These filters were replaced in 1999 by an automated filter press. Since then, the jarosite residue has had a lower water content, and the zinc recovery improved. At present, a second filter press for the jarosite circuit is in the acquisition process to diminish the soluble zinc content in the residue from the present value of 2% to < 1% Zn.

Jan 1, 2006

By Junior Santos

Kinross Paracatu started the operation of the new gold processing plant in the end of 2008, being composed by one SAG mill and two ball mills. During the first year of operation the plant had several problems related to stability and throughput capacity, mainly due to low grinding efficiency of the ball mills. In this period many actions were taken to maximize the throughput rate. Among the actions are reducing the size of balls in the mills, increasing the ball charge in the SAG mill, changing cyclone configuration and return of circulating load to SAG mill. With better stability of the circuit, the second stage of improvements has begun with the objective of increasing throughput rate and also reducing operation costs. Among the actions are the optimization of ball charge in the mills and a better operational control of cyclone parts. After two years of operation was obtained a significant increase in plant capacity, but still requires the addition of a third ball mill in order to maximize the use of SAG mill, which has spare capacity.

Jan 1, 2012

By Louis Frost

"1N 1951, the Dominion Steel and Coal Corporation, as part of a programme of modernization in their coal mining operations at Sydney Mines and Glace Bay, Nova Scotia, undertook the development of two large cross-measure tunnels, which were to be used for the purpose of raising the coal from the underground workings by conveyor belts direct to wash plants located on the surface.These tunnels were to reach from the surface to central loading points underground located at a depth of 600 and 900 feet, respectively. They were to be driven on a pitching gradient of 11 degrees to the horizontal, and they were to reach a length of 3,600 feet in the Sydney Mines area and 10,000 feet in the Glace Bay area.The longer tunnel, 19 feet in diameter, was driven a distance of 1,500 feet and, for domestic reasons, bas not yet been •completed. The other tunnel, in the Sydney Mines area, 18 feet in diameter, is steel supported and concreted throughout its entire length. This tunnel has been completed and will be in operation at an early date.The development of this particutar tunnel posed an additional problem, as the rock through which it had to pass was considered to be water-bearing. In the sinking of Princess Colliery shafts in 1866, a great deal of water had been encountered, and it had been necessary, while sinking, to line the shaft with cast-iron tubbing through the water-bearing strata. The shaft had to be lined for a depth of 300 feet at the upper end. It was anticipated that we would meet with difficulty in driving the tunnel through this strata."

Jan 1, 1955

By D. D. Liu

This paper proposes a charge induction dust measurement method based on detrended fluctuation analysis (DFA) for use in coal mine environments, based upon electrostatic interference, dust properties, wind speed, particle size, moisture content and other factors. In this methods, sequence x(t) is first obtained through a dust concentration sensing probe, and then the cumulative deviation y(t) is calculated, and y(t) is divided into same lengths. Secondly, a first-order linear fit is used for data of each interval, and mean-square deviation filtered DFA was calculated for each interval. Finally, the dust mass concentration of the corresponding time is obtain by supplemented calibration coefficient and fitted the data point which is the mean and square root for all lengths of interval. Simulation and verification experiments showed that the charge induction dust measurement method based on DFA can reduce coal mine electrostatic interference effects with high accuracy. The design has been successfully applied to select areas.

Aug 1, 2013

By F. M. Clement

British Columbia, unlike the Prairie Provinces, cannot lay claim to vast prairies. She can, however, claim many valleys, uplands and plateaus that are capable of marked agricultural development. It has been said that British Columbia is not an agricultural province. This may or may not be true, but at the present time agricultural production in this province stands second only to that of forestry. The industry has advanced from a total production of 8 millions in 1908 to a total production of 60 millions in 1924, a total increase of approximately 650 per cent in 16 years. In the last 10 years production has increased from 30 millions to 60 millions. No other industry can point to such a rapid development. In 1908 British Columbia imported 12 million dollars worth of foods compared to the 8 millions which were produced at home. In 1924 she imported 20 million dollars worth of foods compared to the 60 millions worth produced at home. In addition we exported foods to the value of approximately 10 million dollars. British Columbia is therefore self-sufficing in-so-far as values ar.e concerned except for approximately 10 millions of dollars. It is not to be expected that this province will ever grow all the coarse grains that she may require: these, along with certain meats, will always be a heavy item in the imports. We are concerned at the present time more with the value of the products than with the quantities produced: in other words, with quantities only in-so-far as ? quantities improve value.

Jan 1, 1925

Phelps Dodge has recently operated a commercial scale, super fine grinding circuit of copper concentrates for use in a medium-temperature pressure leaching process. Two 355 kW vertical stirred mills were installed in series, targeting a grind of 80% passing 7.5 µm and 98% passing 15 µm as outlined in Phelps Dodge&apos;s concentrate leaching patent portfolio. This paper details the operation and results of the test program at Bag dad, as well as some of the operating challenges encountered.

Jan 1, 2007

By Michael E. Charles, Jaroslav J. Vocadlo

"The hydraulic transport of solids through pipelines can have many advantages over other modes of transport. Numerous successful applications both within plants and over longer distances have demonstrated the technical and economic feasibility of slurry pipelining. Solids successfully transported include kaolin, coal, iron ore, gilsonite and limestone, and others, such as sulphur and potash, are likely to be transported in Canada in the near future. However, though the technology of solids pipelining is quite advanced the underlying principles have not yet been formulated past the semi-empirical stage. The main objective of this paper is to present a discussion of the important technical and economic considerations in the design of so lids pipeline systems by reference to typical data. The Worthington slurry pumps and pilot facilities are briefly described."

Jan 1, 1972

By L. A. Forsyth

"SINCE I received and accepted your invitation to present to this meeting a paper on A Canadian Integrated Coal and Steel Industry, I have given the subject a great deal of intensive study.Two conclusions have emerged from my considerations: first, that the subject should be dealt with by a person having a firm grasp of its technical aspects; and second, that it is a subject which requires expert analysis of the complicated problems it presents in pure economics.A third conclusion inevitably results from the two just mentioned -namely, that the mantle of the prophet which has been draped up-on my shoulders is too large for me to wear, because I am neither a practical nor a theoretical coal and steel man; and I am not an economist.With the warning that I have discovered, and am keenly conscious of, the inadequacy of my background for the task, I shall attempt to place before you those aspects of my subject which appear to high-light it from a layman's point of view.In the first place, in .order to avoid confusion as between my audience and myself, some definition of terms may be required.As I interpret it I am discussing -a coal and steel industry, using the last word in the generic and not the unit sense, self-sufficient in the provision of all its needs from within the geographical limits of Canada.Now, I start with the proposition that, in the very broadest aspects of such a concept, the Corporation of which I happen to be the executive head meets my definition as a combination of operations resulting in one fully integrated unit of a coal and steel industry."

Jan 1, 1952

By Y. Y. Yemelyanov, S. S. Gudkov, A. V. Boldyrev, A. V. Bogorodskiy, S. V. Balikov

"A series of tests to optimize pressure oxidation- carbon-in-leach process (POX-CIL) of goldbearing flotation concentrate with the addition of sodium chloride and activated carbon were carried out. Flotation concentrate which was generated during primary ores concentration from a large Russian deposit was used for these tests. The tests were performed with different concentrations of sodium chloride. It was found that the required sodium chloride concentration for gold leaching was 5 g/L. The tests performed with different additions of activated carbon showed that the amount of activated carbon should be at least 6% of the concentrate mass. The rate of sulfides oxidation was 67.7–99.8 %. The highest gold recovery was 98.6 %.INTRODUCTIONThe majority of gold-bearing ores are recommended to classify as amenable to cyanidation and refractory. Processes at elevated pressures and temperatures have become increasingly important in base metals hydrometallurgy (Lodeischikov, 1999, 2007; Naboichenko, Shneerson, Kalashnikova, & Chugaev, 2009; Thomas, 2005).Current pressure autoclaves – cyanidation flow sheets are capital intensive due to numerous circuits and the use of environmentally-unfriendly sodium cyanide. The use of halide-based lixiviants during pressure oxidation of precious metals can be a promising technique for refractory sulfide goldbearing mineral raw material hydrometallurgical processing (Fleming, 2002, 2007, Kotlyar, Meretukov, & Strizhko, 2005).In this paper, we presented the results of the research on finding the optimum process parameters of pressure oxidation using an adsorbent for a refractory gold-bearing concentrate. A proposed flow sheet involves (Bogorodsky, Yelelianov, & Balikov, 2012):1. Gold-bearing sulfides oxidation followed by precious metals dissolution and the formation of gold and silver chloride complex;2. Reaction of the precious metals chloride complex with a carbon-based adsorbent;3. Precipitation of precious metals onto the adsorbent by EW and smelting of cathode precipitates into Dore bullions.This process allows POX of gold-bearing sulfides, precious metals dissolution and their precipitation on the adsorbent to be executed in one single vessel. This study found that the most suitable lixiviant was sodium chloride. Fleming (2002) suggested that in the presence of a halide-based reagent (e.g. chlorine- ion reaction), the dissolution of gold during POX is achieved according to reaction 1:"

Jan 1, 2016