Search Documents

By A. Allaire, J. Torrealba-Vargas, R. Welyhorsky

Early testwork was carried out to select the plant process design criteria and flowsheet selection. Additional testwork was carried out during the feasibility study to support the optimization of the plant design criteria. The test results showed that the recovery of gold was not very sensitive to grind size in the range of 75 to 105 microns. An additional result was that the presence of lead nitrate did not improve the kinetics of gold leaching. This conclusion was supported by the low content of sulphides in the ore. It was also found that the presence of lead nitrate increased copper dissolution, producing the potential for an increase of copper reporting to electrowinning, which is detrimental to the overall gold recovery process. The use of oxygen in leaching was investigated to increase leach kinetics. The results of leaching tests to compare using oxygen instead of air indicated that, due to the improved leach time, it was possible to reduce the number of leaching tanks from twenty four (24) to twenty (20).

Jan 1, 2011

By M. Kreuh

An investigation of the pressure pulse spectrum generated by the gas dispersion processes in a Peirce Smith copper converter was undertaken via the simultaneous measurement of four tuyeres using high frequency pressure transducers. The data was captured, stored, and analyzed using digital data processing techniques; including power spectral density plots, band-pass filtering, and a principal component analysis (PCA). The process was characterized throughout by a dominant 3 Hz pulse signature attributed to the formation of lateral gas envelopes. In particular, test tuyeres in the tuyere line tended to operate synchronously at the dominant frequency, regardless of operating conditions tested and despite being distributed along the converter. Synchronous behavior is thought to arise from the acoustic coupling and possible resonance behavior of the gas delivery system on the converter.

Jan 1, 2007

By D. M. MacLean

THE property of Howey Gold Mines, Limited, is situated at Red Lake, Ontario, one hundred and seventy-five miles east of Winnipeg and eighty miles north of the Canadian National railway. The mine has been a continuous producer since April, 1930, and, at present writing, a total of 3,042,690 tons has been hoisted, giving a production of $6,422,858.55, for a grade of $2.32 per ton. From 1,064,477 tons mined during the past two years, however, the yield has been only $1,389,607.03, or $1.41 per ton (gold at $20.67). Present output is at the rate of about 1,470 tons. per day. THE ORE-BODY AND WALL-ROCK: The Howey ore-body is part of a quartz porphyry dyke, which has. intruded an area of greenstone. The dyke strikes north 65° east, and its dip varies from 85° to the south at the surface to practically vertical below the. 1,000-foot horizon. Both along the strike and on the dip, the width of the dyke varies from 25 to 200 feet, the widest portion occurring below the 1,000-foot level. To the east of the ore-body, the dyke increases in width and finally splits into tongues of porphyry enclosed in greenstone, diorite, and congloJ11erate. To the west, it passes into the adjoining property, its width at the boundary being 100 feet. The rock in the ore-body is hard to drill, but, because of numerous horizontal slip-planes, it breaks well when blasted. This characteristic makes it possible to break large breasts or benches with a relatively small number of holes. The ore broken in this manner is consequently quite coarse, a large part of it requiring secondary breaking.

Jan 1, 1938

By Eric Poulin, Anthony Clapperton, Jocelyn Bouchard, Jaime Cristobal Rojas-Montes, Benjamin Legare

"Several grinding mill dynamic simulators have been developed in the last half-century. However, complete circuit simulations are mainly limited to academic investigations, and on-site applications for advanced control or real-time optimization are scarce. One particular issue that has certainly curbed a more widespread use is the time and efforts required for model calibration. This paper illustrates this challenge and presents a calibration method based on dynamic simulation using industrial data and laboratory testwork. The simulator models discussed originate from the work of Austin and Luckie (1972) for grinding mills, and Plitt (1976) for hydrocyclones. A two-stage approach based on a least squares minimization allows determining calibration parameters values. Firstly, laboratory testwork are required for characterizing breakage coefficients of the ore. Secondly, step change responses and their simulation— effect of ore and water feed rates on output flow rates and size distributions—allows identifying transport/mixing conditions. Simulation results are in agreement with actual process responses to variations of feed conditions obtained from a plant survey.INTRODUCTIONDynamic models for grinding circuits has been intensively studied since the 1970's notably by Austin and Luckie (1972b), Klimpel and Austin (1984), Rogovin and Hogg (1988), Napier-Munn et al. (1996), Liu and Spencer (2004), and King (2012) among others. The resulting models primarily serve in simulation applications for process equipment sizing, which incidentally also helps developing a better understanding of comminution operations. An obstacle curbing a more widespread and targeted use of grinding simulation for process control and optimization purposes is the time and efforts required for dynamic model calibration. It remains a cumbersome task that is typically not well detailed in technical papers. This could explain why dynamic process simulators are mainly confined to academic applications."

Jan 1, 2016

By R. R. Song, Q. Li, H. Xing, X. C. Wei

Geomechanical modelling of fault stability is an important part of CO2 capture and storage (CCS) research program to ensure its viability and long-term safety. Storage of CO2 in deep subsurface reservoirs requires estimates of sustainable fluid pressures that will not induce fracturing or fault reactivation which could cause fault slip. More importantly, fault slip gives rise to seismic waves, which inflict severe damage to the cap rock of the reservoirs and may result in leakage pathways for the buoyant plume and thus compromise the integrity of seal formations. In this study, we generated a numerical model tuned towards conditions usually encountered in the Shenhua CCS demonstration project in Ordos basin. In particular, with the purpose of evaluating the sensitivity of the parameters as well as their relationships with the moment magnitude of the seismicity, a variance-based sensitivity analysis was adopted for importance ranking of the uncertain input parameters of the given model. However, such flow models could involve one or several spatial inputs, for instance, fault dip, distance between fault and the injection well, friction angle of fault, permeability of fault, Young's Modulus of fault, injecting pore pressure and the stress field. Studying the sensitivity to each of these spatial inputs motivated the present work. The results led to the following conclusions: fault depth and fault dip significantly affect the behavior of the fault and the fault slip becomes violent with the fault depth increasing and fault dip decreasing. Furthermore, the results indicate that slip time increases with the fault dip decreasing and decreases with permeability of fault increasing. In addition, the calculation of seismic moment and moment magnitude of an earthquake demonstrates that it rises significantly with the decrease of fault dip and the increase of fault depth, and it decreases with the rising stress field. The results show that variations of the only controllable parameter injection pressure do not show great influence to the fault behavior compared with other geological factors, which imply site selection is extremely important for the CCS projects.

Jan 1, 2015

By H. C. Cooke

Those who have followed the geological developments in connection with the copper deposits of Quebec will recall that on many properties the sulphide bodies occur as replacements of fault breccias or tuff breccias, and exhibit a pronounced distaste for the more massive lavas. At the same time the rocks around the ore-bodies are profundly altered, first by addition of silica and sericite, later by conversion of these minerals into chlorite. It has been known for some years that at the Amulet and Waite-Ackerman Montgomery mines these conditions do not prevail. At both mines the ore-bodies are replacements of massive lavas, and at the Amulet they are associated with a very peculiar rock christened ?spotted dog', or 'dalmatianite'. Accordingly, when in 1929 the writer had the opportunity to make a further examination of these properties, two problems presented themselves for solution. The first was to determine, if possible, the conditions under which massive lava, rather than breccia, is replaced by the sulphide masses; the second, to find out the exact nature of dalmatianite and its relations to the sulphide bodies. The first of these problems is believed to have been solved; the second has been found very complex, and will require further work before it is satisfactorily settled.

Jan 1, 1930

By D. Bernard

Over the last decades, the wrought aluminum casting industry has made significant progress with regards to process consistency by the introduction of new technologies in the field of liquid metal processing and casting. These technologies, combined with the application of best practices, have led to increases in productivity as well as better process performances and product quality. The competition in the addedvalue aluminum products (by opposition to P1020 production) is, however, very strong and involves players that did not hold a major role five years ago but who are now exerting a strong competitive pressure on our industry even sometimes from far abroad. There are still technical and technological challenges remaining in the different areas of aluminum casting production, amongst which metal pre-treatment, furnace operations, in-line treatment and casting hold a predominant influence. The comprehension of the contribution of each individual process step to the entire process chain is a key element and must be considered in future process optimisations. This paper presents the technological position of the casting industry and tries to highlight areas where further progress can be made.

Jan 1, 2006

By Floyd B. Bowen

Pumping methods are used, almost exclusively, to transport materials in the mining, beneficiation and chemical processing of phosphate rock in the Florida phosphate pebble field. Matrix pumping systems capable of pumping 15,000 g.p.m., transporting 15,000 long tons (dry) per hour, are now in use. They utilize 16-by 48 Yz -in. pumps, driven by 1.250-h.p. motors, discharging into pipelines 20 inches .in diameter .and sometimes several miles in length. As an average, it is necessary to pump 3 tons of matrix to the beneficiation plants, and to dispose of 2 tons of sand tailings and clay as waste, in order to produce 1 ton of shipping-grade rock. The washers and flotation plants, where the clay and phosphate and silica particles are separated, require the movement of large volumes of slurries with densities ranging from 2-3 per cent to 45 per cent solids, by weight. Extensive waste disposal systems require the pumping of dilute clay slurries in quantities of up to 50,000 g.p.m.,

Jan 1, 1963

By P. Tarassoff

Extractive metallurgy is concerned with the winning of metals from their ores and concentrates. It is therefore not unexpected that extractive metallurgy in Canada has always been closely linked with mining. The discovery and exploitation of new orebodies has provided the impetus for the building of many of our smelters and refineries - past and present - and for the development of new metal extraction processes. The purpose of this paper is to provide a brief overview of those early metallurgical developments, and to highlight the continuing expansion and diversification of the Canadian metallurgical industry.

Jan 1, 1999

By E. Trickey

In the mining industry there exists a constant drive for increased safety and productivity and decreased operating costs. This acts as a driver for implementing advanced technology. As more and more mining operations turn to new technologies, an observed bottle-neck for technology advancement has been the limitation of machine vision solutions available. LiDAR has been seen as a possible solution to the machine vision problem. In the past, a few studies on machine vision solutions have been undertaken by various groups involving scanning laser range-finders and millimetre-wave radar. These studies have done little more than highlight the limitations of both technologies in the mining environment. Little work has been done, however, exploring the applicability of LiDAR imaging technology for mining applications. Neptec Technologies Corp. has developed an obscurant-penetrating LiDAR (OPAL) sensor technology which overcomes the limitations faced by traditional LiDAR sensors when operating in a dusty environment, as well as advanced 3D real-time intelligence (3DRi) data processing algorithms that enable the real-time exploitation of 3D imaging data with sensors mounted on moving vehicles. Working with Teck Resources Ltd. and Barrick Gold Corporation, Neptec is adapting the OPAL sensors and 3DRi technology to mining applications. This paper highlights a number of real-time OPAL/3DRi based mining applications demonstrating how this technology overcomes the limitations of traditional LiDAR to provide a real-time machine vision solution that supports mine machine autonomy.

Aug 1, 2013

"In developing a backfill system handling tailings feed to and from the storage silo, it is necessary to establish a slurry laboratory to develop the technology and silo design criteria. This paper presents the principles involved in such development and the importance of testing principles for optimizing the slurry system. Evaluation procedure based on experiments is applicable to a wide range of materials and allows silo design by scaling up the data gained from model tests. Silo simulation has been successful to design and operation, so becomes an effective approach to backfill applications. IntroductionThe silo is a device comprising specialized equipment and operating with related procedures for storing and handling the mill rejects as backfill slurry. It provides a steady supply of the solids slurry, prepared at desired pulp density under the continuous feed conditions. Because the silo system is designed to accomplish specific objectives when dealing with a particular mill tailings slurry, it is necessary to characterize certain slurry properties, behaviour of the solids slurry and understand the silo performance to establish design criteria. Bench-scale, pilot-scale and dewafull- scale experiments were employed in developing the load-storage-discharge system, and routine procedures are now available for pre-design testing. Silo model experiments and full-scale tests were conducted to define the design parameters and evaluate the silo performance. A silo can be designed by scaling up the silo model geometry and data obtained during tests.Since the early 1960s, silo backfill systems have been widely established. The shape and size of the silo and the operation procedure, as practised, all appear to be relevant to successful operation. Understanding the basic material properties and behaviour of solids slurry retained in the silo will help perfect the silo design, operation procedure and, consequently, improve the silo performance."

Jan 1, 1997

By L. E. C. Pignatari

Mine reconciliation is seen, for many, as a test of the quality of model estimates, while in fact it should be seen as a powerful tool for detecting and correcting problems in each step of mining operations, from resource estimation to metal production. Adequate reconciliation practices allow a more efficient control of the mining processes; however, its results can be illusory unless all parties involved have been in compliance with the principles of sampling correctness. This paper presents a new, segmented reconciliation matrix, which is based on the Theory of Sampling (TOS), developed to monitor gold operations and reserve estimation.

Jan 1, 2011

By L. Li

To accommodate the large payloads and harsh operating conditions associated with heavy vehicles in the mining industry, off-the-road (OTR) tires are typically used with heavy mining vehicles. These tires have increased abrasion and wear resistance due to their thicker tread, sidewall and bead thicknesses. Given these features, OTR tires are much stiffer than conventional passenger vehicle tires and cannot be mounted to a single-piece rim without damaging the structural integrity of the tire during the mounting process. Therefore, multi-piece wheels are used with OTR tires to facilitate mounting. While these assemblies are necessary, several instances of their failure have been reported to result in injuries or fatalities within the mining workplace. Many of these failures were specifically reported to be caused by the disengagement of the wheel lock ring - a component used to securely engage the assembly during operation. In this study, a threaded-connection locking mechanism has been proposed in place of the traditional lock ring design. The performance of this threaded-connection was numerically evaluated in a pull-out test against a conventional five-piece wheel assembly. The pull-out test was devised as a means of quantifying the engagement ability of each wheel?s locking mechanism. A high degree of modelling accuracy was maintained throughout the analysis by validating the vertical and horizontal static loaddeflection behaviour of the rim model of the five-piece wheel assembly against experimental data. Through validation, the model data were found to be within 10.5 and 4.80 %, for vertical and lateral loaddeflection behaviour, respectively. Results from the pull-out analysis found that the threaded-connection demonstrated a 113 % increase in the force required for disengagement to occur relative to the conventional five-piece design - a force of 9,550 kN in total.

Aug 1, 2013

By C. R. Kato, G. Proulx

"Within the continuous scenario of reduced aluminium price and plants production costs increase, the energy consumption optimization in the aluminum electrolytic pots continues as the main focus for the producers. Energy consumption was chosen as a key performance indicator to drive the efforts and actions for improvements. Alcoa improved the energy consumption by approximately 3% from 2005 to 2015. This improvement was a result of best practices implementation, new technologies introduction, strategic actions with plant curtailments and management practices. The main objective of this paper is to highlight the importance of the management practices for planning and operational improvements beyond the technology changes. About 10 years ago, Alcoa reorganized its approach to retain knowledge in the Smelters by using a Best Practices format. For each specific subject, a skilled team defined the minimum requirements and the Best Practices for several aspects of operation and maintenance, which affect the environment, safety, cost, customers and performance. These Best Practices were deployed to all Smelters combined with training sessions to process and operation professionals. We will describe how the Best Practices were organized, the deployment strategy used, and the approach to measure the plants’ success. We will describe the management approach that includes Manufacturing Analyses focused on 3-year potential, annual planning, and weekly monitoring of plant stability. A manufacturing analysis is organized at select plants with cross-functional participation of specialists from technical, operational, procurement and finance. The output of a manufacturing analysis includes a roadmap of enablers to improve energy efficiency. A quarterly follow-up of enabler deployment is held with the plant and resources that participated in the analysis. Annually, there is a Planning Process where energy consumption enablers are selected to be implemented during the next 3 years for each plant. A monthly critical analysis is made by the plants with regional best practice support. On a weekly basis, key performance indicators are reviewed with determination of a stability index for each plant. Any deviation signal of unstable condition is alerted and supporting resources are diverted to the plant to reverse trend with countermeasures.INTRODUCTIONDue to factors like excess aluminum in the market and lower consumption in China, the LME price is declining along the last years, as showed in Figure 1. In 2011, the price peaked at US$ 2,400/ton and since then, continues to trend down and approaching the lowest level at US$ 1,500/ton in the last 5 years."

Jan 1, 2016

By E. Ghali

"Corrosion of support system components (e.g., bolts, mesh, plates) is a safety and economic concern in underground mines. This paper reports the results of a five-year study wherein corrosion coupons were installed at select locations in participating mines, recovered at regular intervals, analyzed for signs of corrosion, and tested to quantify loss in capacity. Complementary tests were conducted on recovered mesh and friction bolt specimens. The data provide insights into contributing factors for support systems corrosion, which aid in the selection of appropriate support strategies and reliable assessment of the useful life and need for rehabilitation of a support system.RÉSUMÉ La corrosion des composantes des systèmes de soutien (p. ex. boulons, grillages et plaques) est une préoccupation économique et de sécurité dans les mines souterraines. Cet article présente les résultats d’une étude de cinq ans pendant laquelle des coupons de corrosion ont été installés à des endroits spécifiques dans les mines participantes; ces coupons ont été retirés à des intervalles réguliers, analysés pour des signes de corrosion et mis à l’épreuve pour quantifier la perte de capacité. Des essais complémentaires ont été effectués sur les grillages récupérés et sur les échantillons de boulons d’ancrage. Les données aident à comprendre les facteurs qui contribuent à la corrosion des systèmes de soutien, ce qui est utile dans le choix de stratégies appropriées de soutien et pour une évaluation fiable de la durée de vie utile et du besoin de remise en état d’un système de soutien."

Jan 1, 2015

By J. A. Ressinger

"The purpose of this paper is to discuss some of the differences between various methods of excavating and loading as they relate to mining operations. The intent is not to provide ""pat"" answers, but instead to raise some questions and set forth some reasonable guidelines.Specifically, the paper deals with the differences and relative merits of power shovels versus rubber-tired front-end loaders - or, carrying this further, comparing what could be called ""stationary"" loading or excavating devices to ""mobile"" types."

Jan 1, 1972

By J. L. Miller, R. W. Burns

This paper sets out the various phases of bringing a merchant bar mill into operation from feasibility consideration through financing, design and scheduling to completion.

Jan 1, 1967

By Lisa L. Van Loon, Neil R. Banerjee

Canada is a world leader in uranium exploration, but many deposits are located in remote regions making exploration targeting challenging. Novel approaches are needed to detect the presence of large-scale ore-forming systems and to vector toward mineralization. Boron is commonly used as a key pathfinder element associated with sandstone/unconformity-hosted and basement-hosted uranium deposits in the Athabasca Basin, but the genetic relationship remains uncertain. Alteration assemblages containing boron geochemical anomalies are commonly spatially-associated with – and possibly coeval with – uranium mineralization. Boron is commonly found in tourmaline minerals but in some portions of ore deposits the host mineral for the anomalous boron remains cryptic. Boron coordination chemistry within alteration haloes can better constrain boron host mineralogy, provide insight into the nature of the boron-uranium relationship, and thus has the potential to better constrain targets for exploration. Synchrotron-source X-ray absorption near-edge structure (XANES) spectroscopy is a direct, element-specific analysis that identifies boron coordinated in both trigonally- (BO3) and tetrahedrally-coordinated (BO4) forms. This makes XANES uniquely suited for identifying the geochemical hosts for boron that may be related to hydrothermal ore forming processes. XANES spectroscopy was conducted on whole-rock assay powders from uranium deposits across the Athabasca basin containing boron concentrations ranging from <10 ppm to >10,000 ppm. XANES directly identifies the relative amount of trigonally- (BO3) and tetrahedrally-coordinated (BO4) boron in these complex mineralogical mixtures. Our work suggests a link between boron and uranium that is likely related to the unique physiochemical characteristics of ore bearing fluids that may provide a unique vector to mineralization.

Jan 1, 2020

By N. F. Faria, F. Monteiro, B. O. Taiwo, A. Palangio, D. Fonseca, J. Manuel

This paper explores the interpretation and application of Particle Size Distribution (PSD) curves in optimizing blast design and enhancing downstream operations. The study looks at important factors like D50, D80, fines content, and the uniformity index to show how PSD curves affect the efficiency of different mining processes. The first section of this paper discusses the impact of blast design parameters such as burden, spacing, and explosive energy on the resulting PSD, highlighting their significance for downstream operations like crushing, and material handling. The section concluded that proper alignment of PSD with downstream size classes, like primary crusher inlet sizes, among others, can result in substantial cost reductions and productivity gains. The second part presents a case study from dstgroup aggregate quarry in northern Portugal, utilizing fragmentation analysis to evaluate blast performance and promote continuous improvement. The section specifically examines the effect of stemming material size on blast fragmentation, comparing the impact of using aggregate with a D80 of 12.32 mm versus a D80 of 21.94 mm. The D80 value represents the particle size at which 80% of the stemming material is smaller, making it a critical parameter in evaluating the stemming's effectiveness in confining explosive energy. The drilling and blasting designs were meticulously planned using O-PitDev and O-PitSurface software to ensure accuracy in blast parameters and layout. To assess the fragmentation resulting from these different stemming material sizes, the study utilized WipFrag 4 software. The software allowed for precise measurement of particle size distribution after the blast, as well as a detailed comparison between the two stemming sizes. Results from the analysis indicate that using bigger-sized stemming material led to improved blast confinement, which in turn resulted in better fragmentation compared to the smaller-sized material. The reviewed blast videos demonstrate that the larger aggregate effectively contained the explosive energy within the borehole, thereby reducing premature venting and directing more energy towards breaking the surrounding rock mass. This led to finer fragmentation with D80 = 1240.1 mm, D50 = 685.9, and Dmax = 2580 mm, which is advantageous in downstream operations like crushing and milling. On the other hand, the smaller stemming material (D80 = 21.94 mm) did not confine the explosive energy as efficiently, resulting in coarser fragmentation (D80 = 1327.37 mm, D50 = 750.76, and Dmax = 2370 mm) and reduced overall blast efficiency. These findings highlight the significant influence of stemming material size on blast performance and fragmentation outcomes. 

May 4, 2025

By P. C. Lighthall, D. W. Zandee, W. Shukin

"IntroductionThis chapter deals with the on land disposal and storage of fine tailing in slurry form behind dams. Other types of tailing, such as coarse dry cobbs from magnetic separation of iron ores and other dry materials, have special problems and are not addressed in this paper. The disposal of mine waste is not included, except as such materials may be of value in the construction activities related to tailing disposal.In earlier North American mining, mines were smaller and frequently disposed of their tailing by direct discharge into neighbouring streams or bodies of water. Where that was not practical or not permitted, the solids were collected in tailing ponds and only the effluent liquids were released or decanted. The dams used for these early impoundments were fragile structures and failures were common. With the advent of large, low-grade open pit mines, and increasing awareness of environmental and safety considerations, recently established mines have carefully-designed tailing disposal systems, with wellconstructed dams and attention given to protection of the environment. Older mines are being improved or at least being examined critically with a view to upgrading as necessary to meet the new standards.Modern tailing disposal systems are highly variable and unique to each mine. Tailing pond selection and design is dependent on available topography as also is the design of transport and water reclaim systems. Suitable sites that are at higher elevations than the mills or distant from them may require that the tailings be pumped. Dams, either earth or rock structures built of the most convenient and economic material, are usually a suitable mix of local borrow, mine waste and coarse tailings. The most economic structures are those built mostly of coarse tailing."

Jan 1, 1989