Search Documents

By B. R. List, E. R. F. Lord

The Syncrude open pit mine, located near Fort McMurray in northeastern Alberta, produces approximately 410 000 tonnes of oil sand feed daily, which, after undergoing a bitumen extraction phase, generates approximately 315000 tonnes of tailings solids daily. The tailings are used to hydraulically construct containment dykes and supporting beaches of the storage facilities. Tailings deposition commenced in May 1978 with the commissioning of the Mildred Lake Settling Basin which is currently composed of approximately 600M m3of solid sand approximately 300M m3of contained fluids with fine tailings in suspension for consolidation. Two other storage facilities, commissioned over the past six years, have been developed to store sand and consolidated fine tailings referred to as mature fine tailings. Fine tailings reduction initiatives being developed will be successful in reducing future production of fine tailings volume by 20%. These initiatives include spiking (addition of fine tailings to coarse tailings lines for deposition), composite tailings (addition of gypsum to promote consolidation) and freeze/thaw dewatering, also to promote consolidation. The mandate of research efforts is to enhance tailings disposal and to develop economical and technically feasible reclamation initiatives. Final tailings landscapes will be geotechnically stable and ecologically productive to minimize or eliminate long-term liability. This technical paper will review the design philosophies of the current facilities and provide an overview of the areas of continuous improvement in the field of tailings management practices through the concerted research efforts and their implementation.

Jan 1, 1997

By J. Kramer, T. Hartmann

In the Hydrometallurgical processes, the presence of the so-called “crud” is a constant challenge in solvent extraction. Crud is a stable emulsion which forms along the interface between the aqueous and organic phase. The spread is influenced by the following parameters: first, wind blows the dust and impurities into the open sedimentation tanks. Second, the undissolved solids such as sand transported in the PLS causing problems in conjunction with incorrect agitator design. The crud fraction can decisively impact the efficiency of the hydrometallurgical extraction because the phase interface can constitute a large fraction and the sedimentation tanks cannot react flexibly to it. In the downstream process of the seriesconnected sedimentation tanks, they are thus all contaminated with crud. At the same time, the necessary mass transport is significantly impeded at the phase boundary between organic phase and aqueous phase due to the crud formation. The transfer of the organic phase into the electrolysis cell can result in a “burnout” of the cathode. The carry-over of this electrolyte into the extraction can cause problems with the pH regulation. The carry-over of the organic components into the raffinate also leads to contamination of the leaching circuit. The continuous treatment of the crud with a 3-phase decanter centrifuge is extremely effective in combating this problem. This technology splits all three phases from each other and they are consequently continuously separated. All subsequent process steps exhibit a stable, uniform effectiveness. The main advantage for the customer is that fluctuations in the process are eliminated and the organic phase can be recirculated back to the extraction. The recycling of the solvent alone justifies the investment in less than 6 months as examples from South Africa and Chile show. To operate solvent recovery in daily operation fully automated online at the optimum limit, the decanter centrifuge is equipped with a concentration-dependent pond adjustment called DControl®. By this means, we can guarantee our customers the maximum possible solvent recovery and minimise the solvent costs in this process step. This system is presented in detail in this paper.

Jan 1, 2012

By Horace Freeman

The sulphur consumed in Canadian pulp mills and acid plants is worth approximately three million dollars annually and amounts to one hundred and fifty thousand long tons, all of which is imported from the United States. Concurrently with a decline in the value of newsprint there has been a gradual increase in the price of this raw material. Most pulp mills in Canada are situated within reasonable distance of domestic pyrite deposits; nevertheless it has not yet been found possible to mine these deposits and utilize the contained sulphur in competition with the imported material. It is the purpose of this paper to elucidate the reasons therefor, and to describe? a commercial-scale experiment undertaken with the object of introducing a native raw material into the Canadian pulp industry on the purely economic basis. Reasons for the Preferred use of Sulphur The known sulphur deposits in the United States are very large, so that at least a twenty-year supply of this material is assured. It is recovered cheaply and in pure condition. Although large deposits of pyrite are known in Canada, nothing has yet been developed to compare in size, cost of mining, or purity with the United States material. It has been necessary to handle and transport more than two tons of pyrite to equal a ton of sulphur.

Jan 1, 1930

By Ma Yuxin, Niu Fusheng, Yuan Zhitao, Bai Limei, Han Yuexin

"Using batch flotation experiment, contact angle measurement, particle size analysis, and scanning electron microscope (SEM), the influence and difference of pH value on the flotation rate of talc and chalcopyrite were investigate without collector at the pH range of 3~11. The results showed that, the flotation rate of talc decrease with the increasing of flotation time, while that of chalcopyrite hardly affect by flotation time, besides, the flotation rate of chalcopyrite is much less than that of talc, so the laws of flotation rate of the two minerals are independent of pH value. The flotation test data of two minerals are simulated with first order and multi-rate flotation kinetic model respectively. The simulation results showed that flotation of talc only meet the first order kinetic model, while chalcopyrite’s meet the both. In addition, According to test results of talc and chalcopyrite by the particle size distribution, SEM photographs and the contact angle measurement, the reason why talc did not conform to the first order kinetic model is not because of particle size distribution, but of particle shape. That is to say, because of sheet structure of talc, the contact angle of layers and sections are 74°and 52°respectively. At the same time, the contact angle of layers and sections are different between the particles. So flotation rates between talc particles are difference.INTRODUCTIONPossessing superior self-induced, collector-induced and sulfur-induced floatability, chalcopyrite exhibits good floatability at a wide range of pH values and potentials. Serpentine are regarded as the most difficult selected type in various chalcopyrite ore, and the predominant reason is that it contains talc. Talc, as a nonpolar layered silicate mineral, is one kind of common associated mineral in sulfide ores (Lu, 2010). Concentrate quality and flotation process of chalcopyrite are influenced as a result from the presence of talc. It is because that talc has inherent floatability which makes it readily mixed with the floated mineral and talc is easy to slime causing the slime coating of the valuable mineral (Beattie et al., 2006). Thus in order to improve the flotation effect of chalcopyrite, methods can be introduced from two respects. One method is that fast-floating talc mineral is floated preferentially, and the other is that sulfide mineral is floated prior to talc by depressing the flotation of talc mineral (Beattie et al., 2006), nevertheless, no matter with which the flotation effect of fine-sized chalcopyrite is not positive. Therefore, in order to realize the flotation separation of talc and chalcopyrite, the difference between the inherent floatability of fine-sized chalcopyrite and talc is researched and analyzed in terms of flotation dynamics in the absence of collector and frother."

Jan 1, 2016

By G. A. Gamble

"The inlet air velocity profile of any surface mine ventilation fan is an important factor when designing the connecting ductwork from the mine shaft collar to the fan. Deficient fan performance can be the result of ductwork that adds unnecessary pressure loss and/or adversely influences the fan inlet air conditions (velocity profile). The need for optimized inlet air conditions begins with discussing the process of performance testing during the development of the fan performance curve. Additional discussions include design of the shaft collar connection and the connecting ductwork. A preferred design of ductwork for parallel fan installations will be illustrated.INTRODUCTIONThe inlet air velocity profile of any surface installed mine ventilation fan is one of the most important factors to consider when designing the connecting ductwork from the mine shaft collar to the fan. Oftentimes deficient fan performance can be traced to poorly designed ductwork that adds unnecessary pressure loss and/or adversely influences the fan inlet air conditions (velocity profile). Such designs may lead to added power requirement, excessive vibration and noise, and reduced fan performance.Understanding the need for optimized inlet air conditions begins with discussing the process utilized when factory testing takes place during the development of the fan performance curve.Additional discussions include design considerations for the shaft collar connection, the connecting ductwork, and fan inlet. Illustrations of cost savings and pressure losses will be included for audience consideration. The design of ductwork for parallel fan installations on the surface is another issue that requires consideration. A preferred method will be illustrated.The selection of accessory components, such as self-closing doors, can also add to the potential for reduced fan performance. Several components will be discussed.An elementary presentation of the Air Movement and Control Association (AMCA) Standard 201 “Fans and Systems” will be included to provide background for those audience members that want additional technical explanations of the need for a uniform inlet air velocity profile at the fan inlet."

Jan 1, 2019

By John S. Stevenson

Zeballos mining camp is on the west coast of Vancouver island; 195 nautical miles northwest from Victoria.; The spectacularly rich gold-bearing veins that made Zeballos an important; gold camp were found early in 1934. Small pockets of very coarse; gold had been found earlier under large boulders at the mouth of Spud; creek; and in the autumn of 1933 rich gold-quartz float was found near the; mouth of the creek. The rocky beds of the steep creeks entering Spud creek; were searched for its source and as a result the veins on the White Star property; were found. The Goldfield vein on the Spud Valley property was discovered; in 1935; and the No. 1 vein on the Privateer in 1936. In the general; prospecting activity that quickly followed; other veins were found; not; only in Spud creek but in other creeks draining into Zeballos river.

Jan 1, 1954

By Samuel O. Akande

"Gold occurs as native metal, in electrum, and in a telluride mineral in quartz carbonate veinlets of three vein systems at the Ross Mine, northern Ontario. The 14 Vein System is made up predominantly of concordant veinlets within layered ankeritic dolomite stratabound by, and conformable with, andesite tuff Individual veinlets contain pyrite, sphalerite, galena, chalcopyrite, tennantite, pearceite, proustite, native gold and electrum in a matrix of quartz, dolomite, ankerite and calcite. The 2B Vein System is made up of both concordant and discordant veinlets within andesite tuffs. The veinlets contain pyrite, chalcopyrite, sphalerite, bornite, tennantite and free gold in quartz, calcite and dolomite. The 18 Vein System is comprised of stockwork veinlets in and around intrusive syenite which has both sharp and gradational contacts with enclosing andesite tuff The veinlets contain pyrite, chalcopyrite, bornite, chalcocite, native gold and calaverite. Sulphide and silicate minerals in veinlets and wall rocks are stable assemblages for the regional metamorphism of greenschist rank. ,The 14 Vein System is interpreted as a metalliferous siliceous carbonate chemical sediment, the components of which were leached from the underlying volcanic rocks by convecting sea water and subsequently deposited on the sea floor between the extrusion of flows and pyroclastic rocks. Subsequent regional metamorphism and intrusions remobilized and redistributed the syngenetic stratabound material into dilatant fractures in adjacent tuff, as in the 2B and the 18 vein systems."

Jan 1, 1982

CSIRO Minerals, in association with the AJ Parker CRC for Hydrometallurgy, has an active program of hydrometallurgical research in which physical and computational modelling are used to better understand and improve a range of different unit operations. The modelling is based on flow simulation (Computational Fluid Dynamics or CFD), but incorporates other physical and chemical phenomena of importance, such as droplet break-up and coalescence, species transport and reaction. This paper reviews some of the major projects that have been undertaken at CSIRO Minerals and will illustrate the critical importance of hydrodynamics to the performance of unit operations and the improvements that can be made to performance using such modelling techniques. Unit operations that are discussed include solvent-extraction, gravity thickeners, flotation cells, bio-heap leaching and stirred tanks.

Jan 1, 2005

By E. J. Marcotte

"INCO LIMITED'S Shebandowan Mine and Mill is located in a scenic tourist and cottage area near the western tip of Lower Shebandowan Lake, approximately 90 Km west of Thunder Bay, Ontario. This nicely designed complex is a positive indication that mining operations can co-exist in harmony within the natural environment.The Shebandowan complex processed nickel-copper ore from 1973 to 1985, inclusive, after which operations were shut down.In late 1988, INCO LIMITED decided to place the Shebandowan complex back into operation, under contract, to mine and mill the remainder of the ore body, according to their specifications. MaclSAAC'S EXPLORATIONS was the successful bidder for the project. Following preliminary rehabilitation, operations were re-activated in late March, 1989. The ore mined to date is of a moderately lower nickel grade than the majority of previous years. However, a higher tonnage rate, combined with improved nickel recoveries, has contributed to a viable operation.A series of mill operating and equipment modifications has enabled MaclSAAC EXPLORATIONS to achieve the quality and grade of nickel-copper concentrates specified, and at the same time, expand mill tonnage throughput while attaining increased nickel recovenes."

Jan 1, 1992

By Dr. Ralph W. Edie

The limestone reef reservoir at Swan Hills consists essentially of a "buildup" of successively smaller atoll-like layers. Precipitation of calcium carbonate within the lagoonal area of each layer essentially kept pace with growth of the outer organic lattice. Within the reef mass, six de-positional environments characterized by specific suites of fossils (or fossil fragments) and associated limestone textures are recognized as follows: ( 1) Aerated moderately agitated water of normal marine salinity (widespread shelf or submerged reef-built platform). Thamnopora-type corals, Amphipora, "pancake" stroma-toporoids, crinoids, articulate bra-chiopods, rare rugose cup corals, and ostracods occurs in light gray-buff skeletal microgranular limestone of low permeability. (2) Semi-stagnant quiet water of normal marine salinity (leeward side of reef). Crinoids, articulate brachio-pods, rare thamnopora-type corals, Amphipora, pancake and bulbous stromatoporoids, rugose cup corals, ostracods and gastropods occur in impermeable dark brown argillaceous skeletal calcilutite with thin black bituminous shale beds and rare dark chert nodules.

Jan 1, 1961

By B. W. Williams

The crack propagation behaviour of Zr-2.5Nb pressure tube material was studied through comparison of the measured behaviour with the predicted response from finite element analysis. Three-dimensional finite element simulations of compact tension specimens were performed using the crack tip opening angle as a fracture criterion to allow for crack propagation. To obtain reasonable agreement with the measured behaviour, it was important to capture both the anisotropic plastic deformation behaviour of the Zr-2.5Nb material through use of the Hill-48 yield criterion and damage due to void growth, nucleation, and coalescence through the use of a Gurson-based constitutive model in the simulations.

Jan 1, 2010

By J. Keith Seidler, David R. Lentz, Douglas C. Hall, Nicholas Susak

Abstract - The Ta-Nb-Zr-REE-rich McKeel Lake alkali granite pegmatite-aplite dike swarm is hosted within the late Silurian multiphase alkali granite intrusion (Welsford) near Browns Flats in southwestern New Brunswick. A steep easterly dipping series of pegmatite-aplite dikes trending 170º can be traced 150 m along strike; they are up to 40 cm wide, closely spaced (10-20 cm apart), and interconnected by narrow branching dikelets that generally trend perpendicular to the overall strike direction. The Welsford intrusion has mantle A-type affinities characterized by enrichment of Zr, Ta, Nb, Th, and rare earth elements (REE). Two separate sets of dikes have been identified: (1) an unmineralized fine-grained porphyry, which occurs at depth and seems to be the youngest intrusive phase; and (2) a mineralized pegmatite-aplite dike swarm (419 ± 20 Ma) that crops out at surface. The mineralized pegmatite-aplite dikes likely represent a late magmatic, highly fractionated phase of the Welsford intrusion. XRF and INAA data indicate that the Welsford intrusions and related pegmatite-aplite dikes show elevated levels of Ta (74-220 ppm), Nb (750-3,040 ppm), Zr (1,450-36,000 ppm), Y (540-3,070 ppm), Th (170-870 ppm), U (60-250 ppm), Ce (430-1,950 ppm) and Yb (110-290 ppm). Electron microprobe analysis of two samples identified Ta-Nb- and REE-rich phases: euxenite, fergusonite, aeschynite, (Y)-aeschynite, and a REE carbonate.

Jan 1, 2005

By H. Vendette, N. R. Dando, A. Moras

The thorough analysis of results obtained from different testing campaigns performed on an alumina dry-scrubber pilot installation treating aluminum potline offgases, suggests a clear relationship between the emissions of gaseous fluoride and the fluoride saturation level of the alumina. The integration of this relationship into the development of a new generation of alumina dry scrubber represents an intriguing challenge regarding the design of more efficient air pollution control equipment. An innovative scheme challenging conventional industry practices was proposed. From theoretical simulations, the reduction in fluoride emissions can potentially be reduced by as much as 50% in the summer season. To validate this innovative approach, Solios in partnership with Alcoa Primary Metals, modified one of the Aluminerie de Deschambault's systems by adding new temporary equipment on the operating units and subjecting it to several test campaigns. This article presents the first results obtained in testing this new and innovative approach on alumina dry scrubbers used to capture fluoride emissions coming from aluminum electrolysis potlines.

Jan 1, 2006

By Francis Wm. Gray

The preparation of a paper read before this Society in 1927 on Undersea Mining led to representations to the Deputy Minister of Mines at Ottawa, Dr. Chas. Camsell, and to the Director of the Geological Survey and the Director of the Mines Branch, which resulted in the undertaking by these bodies of a geological, physical, and chemical survey of the Sydney coalfield, combined with revision of the geological maps, on all of which much progress has been made. Preliminary studies revealed the necessity for a new base-map on a scale that would permit the representation of the whole coalfield from cape Dauphin to Mira bay on one sheet, and in the making of this map the Geodetic and Topographical Surveys have collaborated, with the assistance of airplane surveys for filling-in of detail. The new map will show all the data accumulated by 50 years of active mining and will show also the extent of mine workings, with level-contours under the sea. Dr. W. A. Bell, of the Geological Survey, has, over a number of seasons, studied in the field the historical geology with the purpose of elucidating the sequence of earth movements that have determined the structure of the coalfields, especially those that have governed the course and extent of the complementary folds that traverse the Sydney coalfield. Dr. B. R. MacKay, of the Survey, and the officers of the Fuel Testing Laboratories at Ottawa have made exhaustive studies of the Phalen seam, chemical and microscopic, intended to elucidate the conditions under which this seam was deposited, and some very interesting conclusions have been reached.

Jan 1, 1934

By Karl J. C. Harries

"2.1. INTRODUCTIONNo agreement can be perfect in the sense that it contemplates and provides for all eventualities. Mineral acquisition agreements are usually negotiated and drafted at a time when an orebody is no more than a gleam in a geologist’s eye, so it is hardly possible to provide for development and operation in other than the most general terms. However, an agreement that stops short of contemplating the possibility of an orebody and production is ill-advised. Accordingly, it is important to provide procedures to make decisions that will let the project proceed, even in the face of a fallingout between parties. Whether the parties are shareholders in a corporation or venturers in a contractual common undertaking like a joint venture, differences of opinion and disputes will occur. Unfortunately, more and more are ending up before the courts. Besides greed and the growing tendency in society to fight rather than talk, there are other factors that contribute to the increase of litigation. In some jurisdictions, agreements have tended to become complicated, often defying interpretation, even by a lawyer, and explorationists want their budgets to go into the ground as constructive work rather than into a lawyer’s pocket. All this has led to a growing tendency for corporations to take the attitude that the chances of finding a mine are, at best, marginal and there are lots of earlier agreements in the files to draw from, so why not prepare their own agreements? As discussed in the preceding chapter, this can be folly. All these factors can quickly have parties facing each other in court while a project sits idle. Added to this is the problem that, in some jurisdictions, lawyers may take cases on a contingency-fee basis, sometimes promoting the pursuit of a nebulous claim.When an orebody is discovered, someone will always want some, or more, for himself. There is a breed of “prospectors” who prospect for legal actions, on the somewhat sound grounds that a major corporation will buy off nuisance litigation, rather than incurring the cost and effort of attacking even a poorly founded claim in the courts. They may even find a winner. Besides, it is far more comfortable and relaxing to prospect for problems and legal niceties than to prospect for an orebody.1 In short, it is appropriate to consider briefly some of the factors relating to lawsuits and judgments. Although many of the comments are made in the context of the common law and the Canadian legal system, most of the concepts and suggestions are applicable to any legal system."

Jan 1, 2003

By S. Banisi, A. Haji-Zadeh, A. R. Hasankhoei, M. Maleki-Moghaddam

At the concentration plant of the Gol-E-Gohar Iron Ore Company (Iran) three 9m × 2.05m AG (Autogenous) mills (fixed speed) are used in parallel in a dry operation. The test works conducted in a scale down mill with a diameter of 1m indicated that conventionally used "deflector" type liners did not provide efficient environment for grinding. In this research, to improve the grinding efficiency, a new design using low profile end liners incorporating radial ribs of proper height was investigated. In order to determine an appropriate liner design at different operating conditions, a 100cm×10.8cm model mill was used for experimentation. The special design of model mill made it possible to increase the radial ribs height in steps of 6mm up to 18.5mm. The transparent end of the mill enabled accurate trajectory determination by image analysis. The results indicated that the new lower height profile deflectors and 15.5mm-height (14.5cm in industrial scale) radial ribs improved the mill performance while avoiding excessive pressure drop across the mill and wear on the liner. The image analysis showed that the use of new liners increased the distribution of coarse particles across the mill cross section from 28% to 35%. A new liner design was proposed by decreasing the number of liners in each slice from 5 to 4 pieces. The thickness of the inner head liners reduced from 45cm to 30cm and the outer deflector liners replaced by radial ribs. The distance between the feed and discharge inner head liners increased from the original 115cm to 145cm which increased the effective length of the mill by 26%. The new design reduced the weight and volume of end liners by 9% and 23%, respectively. It was predicted that the new liners design increases the mill throughput by 10% and reduces the metal consumption by 20%.

Jan 1, 2016

By Joseph D. Martinez

"The benefits of modern technology can readily be identified with energy availability. A clear correlation has been established between per-capita energy consumption and the GNP for various nations. The United States is an outstanding example of a nation which has benefited from vast energy reserves. The nation is now challenged, how¬ever, by dwindling reserves and the need to develop new sources consistent with the preservation of environmental quality. The development of new, virtually inexhaustible and environmentally acceptable sources cannot be expected for several decades. Meanwhile, we will have to depend on coal, nuclear energy and/or rigorous conservation measures.The net effect of environmental considerations has been to delay and perhaps ultimately eliminate the nuclear energy option as a national energy alternative. This forces a more positive move toward coal as the next major source of electrical power. Our coal resources are large, but the use and production of coal is also a threat to the environment. Thus, we seem to be moving from one major accessible source to another due to environmental concern only to face the probability that the alternative is also environ¬mentally unacceptable.Controversies revolving about energy choices must be resolved by an analysis of the relative benefits and impacts of these two sources and others. The pattern of changing energy sources is not new. We have moved from wood to coal to oil and gas in the past and must learn to adapt in the future. Rational decisions must be made relative to the utilization of intermediate energy sources pending development of promising future approaches. A collapse of current levels of energy supply could threaten our technological society and the means to develop a new energy base."

Jan 1, 1976

By A. Brown

"The mining industry is no exception to the general rule that continuing research is essential to good management; in fact, because of the imperfect state of knowledge in regard to many important factors associated with a mineral extraction, mining research assumes a position of unusual importance. On the basis of a recent visit to mining research centres in a number of European countries, the author describes their organization and their role in the mining industries of these countries. Some observations are made on Canadian mining research efforts, with a view to indicating a more systematic basis of procedure."

Jan 1, 1960

By D. A. Le, T. S. Nguyen

"In Canada and other countries, several types of rock formations are being considered for the geological disposal of radioactive wastes. In order to better understand the ability of these rocks to contain and isolate the wastes, the Canadian Nuclear Safety Commission collaborates with different international research organizations and has access to experimental data from Underground Research Laboratories (URLs) in the world. Such an URL is situated in Opalinus Clay, at Mont Terri, Switzerland. An experiment, consisting of the excavation of a tunnel followed by water and gas injections in a test section of the tunnel, was performed at the URL. The authors have developed a mathematical model, based on the poromechanics theoretical framework, to simulate those phases of the experiment. The constitutive relationship for the stress-strain behaviour of Opalinus Clay takes into account its inherent anisotropy due to bedding. The model was able to capture the main features of the experiment such as the prediction of the shape and extent of the excavation damage zone and its influence on water and gas migration.INTRODUCTIONIn Canada and many other countries, several types of rock formations such as crystalline rocks and sedimentary argillaceous rocks, are being studied for the disposal of used nuclear fuel from nuclear power plants. Geological disposal relies on multiple natural and engineered barriers for the long-term containment and isolation of the wastes. The host rock is a major natural barrier and is the subject of extensive research. The Canadian Nuclear Safety Commission (CNSC), Canada’s nuclear regulator, will be responsible for the licensing of future deep geological repositories. In order to evaluate the safety of deep geological repositories, CNSC staff keep abreast of scientific developments by collaborating with national and international partners on experimental and theoretical research on the long term performance of those engineered and natural barriers. Through that collaboration, the CNSC has access to data resulting from experiments performed at different Underground Research Laboratories (URLs)."

Jan 1, 2015

By R. Khettabi

The mechanical, thermal and bioproperties of titanium alloys allow their wide use in different industries. Compared to aluminum alloys, titanium alloys are very tough, making them that much more difficult to machine than aluminum alloys. Most studies conducted on these types of materials have mainly covered and made comparisons in terms of cutting speed, cutting force and mechanical properties. Recently however, their sustainability and environment parameters have begun to attract significant interest, and it has been found that machining processes generate particles that can be harmful for health and the environment. In this paper, particle emission is investigated during the turning of the titanium Ti6A14V and 6061-T6 aluminum alloys.

Jan 1, 2011