Search Documents

By A. Djebara

Today, indoor air quality, especially in manufacturing industries, is of great interest due to the use of new processes and advanced materials such as those containing nanoparticles. Manufacturing processes generate aerosols (dry or wet) which can be detrimental to occupational health and safety and to the environment. Controlling metallic particle emissions during machining processes should limit their formation at the source, and thus minimize the risk of exposure; this at-source reduction requires the characterization of the particle emitted (size, nature, concentration, etc). The metrics normally used in characterizing fine and ultrafine particles include the mass concentration, the specific surface and the number concentration. Most of these metrics are affected by the size, the geometry and the density of the measured particles. Information about the form and the real size of the particles is thus very important. A procedure for collecting and characterizing fine and ultrafine metallic particles was developed and applied to the study of particles emission during the machining of aluminum alloys. It was found that metallic particles emitted during the machining of aluminum alloys are of various shapes and sizes, and this information must be taken into account when characterizing these particles.

Jan 1, 2011

By Ashu Garg, Anirban Bhattacharya

"Friction stir spot welding of aluminum alloy AA6061-T6 sheets was performed with circular (plunge depths 0.4 and 0.6 mm), square and triangular tool pin (plunge depth 0.4 mm) with constant 0.2 mm shoulder penetration to characterize various zones of weld nugget. It was observed that the depth of the stir zone formed below the tool pin is comparatively similar for different tool pins but wider for circular tool pin. The size of another stir zone formed at the interface of tool pin and a tool shoulder is observed to be larger for triangular and square tool pin due to the higher swept rate. Predicted strain from finite element analysis, calculated strain rate using Zener-Hollomon relationship and experimentally measured grain size distribution indicates severe amount of plastic deformation in-and-around the nugget/spot region. Finer grains in various stir zones were observed than thermo-mechanically and heat affected zones. Grain size (at distribution peaks) in stir zones varied around 2.54 µm to 3.69 µm for different tool pin profiles as compared to base metal grain size of 20 µm. Microhardness results indicate that the welded region is quite softened than base metal and maximum hardness is mostly observed around the thermo-mechanically affected zone.INTRODUCTION Friction stir spot welding (FSSW) is widely used for joining the sheets of materials like aluminum, copper, magnesium, etc. The process begins by plunging a rotating tool (generally having a pin and a shoulder) into the sheets to be welded. Continuous stirring of the tool and downward plunging force generates localized heat due to friction at the tool-sheet interface and plastic deformation of the sheet metal. The material gets softened and the plasticized material adjacent to the tool pin starts flowing due to the action of tool rotation and tool plunge thereby causing intermixing and bonding between the overlapped sheets. The tool stirring also promotes grain refinement in the weld nugget associated with high strain, strain rate and thermal cycle. The formation of new microstructure also affects the mechanical properties and efficiency of FSSW joints. Studies also showed that the tool pin design and tool shoulder feature exerts a noteworthy influence on the material flow and intermixing during the FSSW process (Reilly et al., 2015; Hirasawa et al., 2010). Sarkar et al. (2016) studied the material flow and intermixing during FSSW using tracer material method and reported that the size and width of flow zone increases with tool penetration depth. The influence of tool rotational speed on microstructure and stir zone temperature was investigated during FSSW of dissimilar AA6061-AA5754 alloys (Gerlich et al., 2007). They reported that the average grain size in stir zone of AA6061 weld increases with increase in tool rotational speed. In another work, Gerlich et al. (2008) studied the local melting and tool slippage during FSSW of Al alloys. Tool slippage was investigated by calculating the strain rate using Zener-Hollomon relation. Garg and Bhattacharya (2017a) studied the effect of dwell time, tool pin profiles and tool rotational speed on shear strength, microstructure, temperature and strain distribution during FSSW of AA6061. In another work, Garg and Bhattacharya (2017b) analyzed the effect of different tool pins and pinless tools on the shear strength and microstructure during similar and dissimilar FSSW of AA6061-T6 and pure Cu. Chang et al. (2004) proposed mathematical relationship between the average grain size and Zener-Hollomon parameter during friction stir processing of Mg alloy. Solhjoo (2010) presented a mathematical approach to determine the critical strain as a function of peak strain required for initiation of dynamic recrystallization in austenitic stainless steel. Fratini and Buffa (2005) also proposed the numerical model to determine the grain size during continuous dynamic recrystallization phenomenon."

Jan 1, 2018

By Corby G. Anderson, Caelen D. Anderson, Patrick R. Taylor

"The United States contains a variety of domestic rare earth element mineral sources containing such as ancylite, bastnasite, monazite, and xenotime. Research has been performed to investigate the fundamental surface chemistry involved in the froth flotation of these minerals, and apply the knowledge gained to substantiate the results through experimental testwork on a domestically sourced rare earth ore. This paper will outline the fundamentals and literature of rare earth mineral flotation, review its industrial applications and provide some recent research updates.THE RARE EARTH ELEMENTSRare earth elements (REE’s) are a unique family of elements with nearly identical physical and chemical properties. They account for approximately 1/6th of all naturally occurring elements, but the entire group occupies only one position on the periodic table. These 15 elements make up the lanthanide series (atomic numbers 57–71), and all but one (promethium) occur naturally. In addition to these 15 elements, yttrium and scandium are also considered rare earths since they tend to occur in the same deposits as the rare earths and share similar physical and chemical properties as seen in Figure 1. In particular Figure 2 denotes, a cartoon of the subtle differences in each caused by the 4f atomic sub shell (Gschneidner Jr., 1964). These subtle differences result in very difficult challenges in the selective concentration and final separation of each rare earth. (Anderson, 2015, Kronholm, Anderson, Taylor, 2013)Rare earths are separated into two different subsections; the “lights” or LREE’s (lanthanum57 through europium63) and the “heavies” or HREE’s (gadolinium64 through lutetium71). Yttrium is generally considered a heavy rare earth since its ionic radius is close to that of the HREE’s, while scandium is not considered either a light or a heavy."

Jan 1, 2016

By G. Bonin, R. P. Preston

"This paper presents a series of case studies where spherical camera photographs were used to generate 3D shaft models using photogrammetric methods. The shaft models were, checked for accuracy by comparing them to overlapping laser scan data, provided survey data or idealized shaft models. Short lengths of model were found to more accurately reproduce the shaft surface, with a best observed accuracy of 8 mm. Longer models encountered errors with accumulated errors as exhibited by slight deviations from vertical or slightly conical model shape. At present, the models are considered acceptable for general documentation and gross change detection. INTRODUCTION Shaft inspections are required by mining regulations in many jurisdictions and are commonly completed by trained mine personnel via visual inspections. This can be time consuming and prone to errors due to lapses in attention and the rapid travel rate required to inspect an entire shaft in a reasonable amount of time. Similarly, because of the time requirements, there can be impacts on other aspects of mining as a result of occupying the shaft for inspections. Spherical cameras with supplemental light systems offer a modern addition or alternative to conventional inspections. These cameras can be lowered relatively quickly to collect high definition, fully illuminated videos of the shaft that can be reviewed in detail later while the shaft returns to service (Gillis et.al., 2019). The use of cameras offers a further opportunity for valuable survey data generation from the same original data stream. The video data can be processed into three-dimensional (3D) models using Structure-from-Motion (Westoby et al., 2012) based photogrammetric methods. Depending on the quality of the source video and availability of survey control (required for all photogrammetry models) these models can be very accurate. Shaft surveying can be conducted with traditional theodolite methods but such surveys are time consuming and limited in their data density. Similarly, scans can be completed using conventional terrestrial laser scanners, but this requires a significant number of distinct setups to provide sufficient overlap between scans. Work is being conducted both on the laser scanning (SLAM, Durrant-Whyte & Bailey, 2006) and photogrammetry fronts towards kinetic scanning (Benecke, 2017) systems. The major advancement which is permitting these kinetic systems is Inertial Measurement Units (IMUs) which can provide localization in GPS denied environments and reduce errors associated with the open traverse format associated with shaft scanning."

Jan 1, 2019

By K. Law

"The Hatch Product Transport (HPT) system is a highly flexible and configurable route selection and sequencing system for controlling large bulk material handling facilities. The system has a generic control algorithm that can be configured to suit any material handling facility. It can also be easily reconfigured to cater to plant expansion or modifications without incurring significant disruption to the existing production, costs in testing, and re-commissioning, thus achieving cost savings throughout a facility’s lifecycle.This new material handling control system has been installed at BHP Billiton’s Port Hedland iron ore terminal to facilitate its expansion to beyond 100 Mt output capacity."

Jan 1, 2006

By N. Shi, T. G. Joseph

ABSTRACT: An interactive cable shovel simulation has been developed to mimic any shovel dipper geometry for a given cable shovel operating in any homogeneous face material. This interactive cable allows the user to predict shovel performance in any face material encountered and track both its ground stability and the dipper-ground interaction. An embedded Microsoft® Visual Basic spreadsheet was used as the platform for developing an interactive simulation that allows for maximum user-defined parameter input and interactive visual output. The result is an analytical dipper-ground interaction solution that yields crowd, hoist, and digging effort as a function of face activity position.

Jan 1, 2011

By S. Sundararajan, Z. Lin

ABSTRACT Fierce market competition and demand have made it imperative for mining companies to achieve higher productivity and operational efficiency. The selection of the best mining method and equipment combinations will enable companies to meet production and efficiency targets. Continuous mining is increasingly preferred by companies for its high efficiency and low unit costs. We developed simulation models for two continuous mining systems: the continuous surface miner (CSM) system and the at-face slurrying (AFS) system. Considering two different case studies, the paper discusses application of developed models to determine the optimal number of trucks and equipment capacities for the two systems.

Jan 1, 2013

By J. S. DeLury

Introduction The problems of metallogenesis are largely related to those concerning the origin of igneous rocks, which, in turn, are involved with the question of crustal mechanics. Many ore-bodies are genetically related to associated intrusive and there is an equally close association apparent between igneous intrusion and crustal deformation. The problem of ore-deposition is concerned, therefore, with the fundamental problems of geology. For a long time speculations regarding crustal movements rested largely on the contraction theory and its associated conceptions. Vertical movements were considered to be all important and horizontal movements secondary to them. Magmas were pictured as rising more or less vertically in the crust and were believed to form in vertically disposed magma-chambers or reservoirs. The principle of magmatic differentiation seemed to offer the best explanation of the origin and association of diverse rock types and it seemed also to require the existence of quiescent magma-chambers for the admittedly slow process of differentiation. Accumulating evidence of the importance of horizontal movement in the crust, has, along with other considerations, discredited the contraction hypothesis and many of the inferences that go with it. The same evidence may require some change in the prevailing conception of the origin of the various types of igneous rock and of the mechanics of intrusion. Geologists are now at sea concerning some of the vital and fundamental problems of the crust, and the field is open for speculation. The writer is developing a hypothesis which seems to permit an explanation and? a correlation of earth structures and phenomena. If it rests on a firm foundation, the hypothesis, because it is fundamental, is certain to have a profound bearing on the problems of economic geology. It is for this reason that an outline of the hypothesis is offered at this time. Only a few of its economic bearings are foreseen at this time and these will be indicated.

Jan 1, 1932

By J E. Gordon

For many years, it has been known that certain loud noises may, with prolonged exposure, temporarily or permanently damage a person's hearing ability. Pneumatic rock drills, al-though among the offenders, have, until recently, remained unaltered and unrestricted as to noise output. Now, there are drills available with higher rates of penetration and yet with noise levels reduced to those of previous models or less. Use of such drills, when proved to be superior in noise attenuation and of acceptable performance, should be encouraged in order to reduce future hearing losses to a minimum. People Have the Right to Hear P ERHAPS the earliest recognized indication of hearing loss due to industrial noise was the deaf-ness developed by the workmen in boiler factories. Here, the vibration set up in the shells by the riveting hammers gradually deteriorated the workmen's hearing, especially those whose job it was to hold the dollies inside the drum, where the sound is greatly intensified by reflection

Jan 1, 1963

By Larry A. Morris

The environmental impacts of industrial activities have become very serious concerns of the public over the past few decades. Not surprisingly, governments have responded with legislation and regulations to force industry to operate in a more environmentally responsible manner and, more recently, have prompted industry to initiate voluntary measures in response to specific environmental issues. The concept of Product Stewardship has evolved as a system or vehicle for the industrial sector to demonstrate an active concern about the environmental impact of their products, services and processes.

Jan 1, 1996

By Larry A. Morris

The environmental impacts of industrial activities have become very serious concerns of the public over the past few decades. Not surprisingly, governments have responded with legislation and regulations to force industry to operate in a more environmentally responsible manner and, more recently, have prompted industry to initiate voluntary measures in response to specific environmental issues. The concept of Product Stewardship has evolved as a system or vehicle for the industrial sector to demonstrate an active concern about the environmental impact of their products, services and processes.

Jan 1, 1996

By Hamidreza Soltanzadeh

The injection of CO2 into a reservoir or aquifer can potentially result in deformation, induced fracturing and fault reactivation in the injection zone and/or the rocks that surround it. This paper reviews the data collection and geomechanical analyses performed to assess these potential hazards for the Heartland Area Redwater Project (HARP), in which CO2 sequestration is being considered in a carbonate (Leduc Formation) reef. A three-dimensional mechanical earth model (3D MEM) was developed using available geophysical log data from several wells. The geomechanical response to CO2 injection was studied using a finite element numerical model based on the 3D MEM and pore pressure distributions predicted using a reservoir simulator. The modeling results suggest that the potential for induced fracturing and fault reactivation is low and the maximum predicted ground surface heave is less than 2 cm. Sensitivity analyses conducted with a 2D geomechanical model that was extracted from the 3D model confirm that this conclusion holds true even when a reasonable measure of uncertainty in rock mechanical properties, ambient pore pressures and horizontal stress magnitudes is accounted for.

Jun 1, 2012

By George F. Crocker

Introduction The Helen mine and the Victoria mine of Algoma Ore Properties, Limited, in the Michipicoten district, Ontario, are 120 miles north of Sault Ste. Marie, on the north shore of lake Superior. They are on the Algoma Central railway between Hawk Junction and Michipicoten Harbour. Between them, these mines have produced 10,757,113 tons of iron ore. From 1900 to 1918, 2,823,369 gross tons of brown ore was shipped, and from 1939 to the end of 1949, 7,933,744 tons of siderite was produced from the open-pit operations and underground development. The finished product, known as 'Algoma sinter', is shipped to blast furnaces both in Canada and the United States. The iron-ore bodies are a part of a tabular shaped area of iron formation that extends over a length of more than 10,000 feet and has maximum width of 1,000 feet. The two siderite orebodies, known as the Helen and Victoria, are separated by two diabase dykes. The Helen orebody is 1,600 feet long with a maximum width of 250 feet and the Victoria is 1,200 feet long with a width comparable to the Helen. These orebodies are considered to be a replacement of the original rock by iron carbonate. The introduction of the iron-1bearing material probably occurred after the development of the major folded structures. The open-pit mining of siderite started in the Helen ore body in 1939 and continued until 1945. During this period, 3,853,395 tons of ore was mined. Open-pit mining started in the Victoria body in 1946 and is still being carried on. Underground development commenced in September, 1947. Diamond drilling and surface sampling had shown the Helen deposit to average 35.61 per cent Fe and 7.28 per cent SiO2, and the Vi.otoria deposit 33.73 per cent Fe and 10347 per cent SiO2?

Jan 1, 1950

By T. E. Morimoto

Summary The Research Council of Alberta has made a series of tests with the cyclone washer to investigate the influence of the following operating variables: underflow apex diameter, .specific gravity of medium, pulp ratio, density distribution of the feed, and size analysis of the feed. The results obtained for all the variables studied, except size analysis of the feed, are included in this paper. The tests were made with smaller underflow apex diameters and lower specific gravity .suspensions than have been recommended by Cerchar for the sharpest separations. However, what is considered to be sufficiently good cleaning was accomplished with a suspension of 1.30 specific gravity and an underflow to overflow diameter ratio of 0.56. It was found that the sharpness of separation was not affected appreciably by variations in specific gravity of suspension or underflow apex diameter provided that the density of separation was within the normal range of washery operation. Cyclone performance was not too adversely affected by decreasing the pulp ratio. The minimum figure which gave reasonable separation was 4 to 1. The tests with various density distributions of feed revealed .that the degree of washing difficulty had no detrimental effect on the .sharpness of separation given by the cyclone. Introduction A major problem of the bituminous coal industry today is that of reducing the ash content of the finer sizes (minus 1/4-inch) of coal. This problem is particularly acute in Alberta, where, because of tectonic movement subsequent to deposition, the coals have been rendered friable, and bands of impurities have been intimately mixed with the clean material. As a consequence, most Alberta coals, as mined, contain a large proportion of fines and have a high inherent mineral-matter content. The advent of mechanized mining and stripping operations ?has further aggravated this problem.

Jan 1, 1952

By K. E. Waters, M. Mirnezami, R. Gauvin, A. Jordens, K. W. Malas

"There is currently very little information on the physico-chemical properties of rare earth elementbearing minerals, or on their processing. With the increasing demand for rare earths, this is something that needs to be addressed. This paper introduces some surface chemistry analysis of fergusonite (YNbO4), and the bubble-particle attachment. Zeta potential measurements indicate adsorption of sodium oleate and, to a lesser degree, potassium amyl xanthate onto the surface, and an increase in attachment to an air bubble is observed at pH 4.5 and 6.5. At a pH of 10.5, no attachment is observed, whether in the presence of the reagents or not. This analysis, although initial, will be used to initiate flotation tests, in order to facilitate the selective recovery of fergusonite. INTRODUCTIONRare earth elements (REE) are increasingly in demand, due to their prevalence in both renewable energy devices and high-end electronics. An article in the New Scientist highlighted the importance of a number of REE, many of which most people are be unlikely to have heard mentioned (Crow, 2011). From batteries (lanthanum and cerium) to magnets (dysprosium and neodymium) and lighting (yttrium), the REE are crucial to the advancement of technology and energy saving devices. For example, neodymium is finding most use in the high end magnets that keep the motors turning that power wind turbines and electric cars. In the case of yttrium, the demand outstripped the supply in 2010, emphasising the need to develop deposits containing this and other REE (Crow, 2011). The impact of our dependency on REE has become even more apparent with the reduction in exports by China, which currently controls 97 % of the world’s rare earth production (Pitts, 2011).With the increasing demand for rare earth elements (REE), there is a drive to exploit the known resources around the world. However, the physical beneficiation of the rare earth element bearing minerals is a subject which will require a great deal of investigation to fill the knowledge gaps surrounding these developing rare earth projects. There are numerous articles on REE mineralogy as well as the hydrometallurgical processing of REE concentrates (Alex, Suri, & Gupta, 1998; Peter Gromet & Silver, 1983; Ring et al., 1993; Schnetzler & Philpotts, 1970; Uda, 2000), however a common feature amongst these resources is the lack of detailed descriptions of the physical beneficiation processes required to concentrate REE-bearing minerals. There is work being conducted into reagents and methods for use in recovering some rare earths from their associated ores (Bulatovic, 2010; Ni, Parrent, Cao, & Liu, 2011), but much more in-depth research is required."

Jan 1, 2012

By Douglas C. Fraser

A DIGHEM survey was flown in the Belford-Montcalm Township area of Ontario in November 1975. This 600-linemile survey resulted in the detection of 134 EM anomalies. The Montcalm Township copper-nickel discovery yielded a single-line anomaly having a conductance of 154 mhos. This anomaly was highly visible because (a) it had the highest conductance in the survey area, (b) it correlated with a 175-gamma thumbprint-shaped magnetic anomaly and (c) it was isolated from long conductive bands. The deposit is a copper-nickel pyrrhotite body which occurs in gabbro and strikes north-south, parallel to the flight lines. The DIGHEM survey was flown north-south, because the exploration program was primarily concerned with locating copper-zinc sulphides in the east-west-striking felsic volcanics. The flight line passed close to the deposit and yielded a 9-ppm anomaly on the chart record. The computer analysis showed that a deposit of exceptionally high conductance (154 mhos) caused the relatively weak (9 ppm) anomaly. The ground follow-up program of magnetics and EM led quickly to the discovery drill hole, which penetrated the orebody in September 1976. Subsequent geophysical surveys consisted of horizontal-loop EM, pulse EM, magnetic and induced polarization surveys over an area of about 8 claims. In addition, a detailed DIGHEM" airborne survey was flown at a line spacing of 100 m to evaluate the entire property of 620 claims. This detailed survey yielded EM conductor maps and contour maps of resistivity, magnetics and enhanced magnetics.

Jan 1, 1978

By S. A. G. Poppen, J. Konopka

"Petro-Canada's project investigative and experimental underground work in the Galt coal seam at Kipp, Alberta included the construction of an emergency egress and ventilation raise from surface.The Galt coal seam is 206 m below the surface and covered by 8 m of shale, sandstone and clay beds of the Oldman Formation, 128 m of shale, bentonite beds and sandstone of the Bearpaw Formation, and 70 m of glacial till and basal gravel. Free water was encountered from sand lenses in the glacial till and the basal gravel.Excavation for the ventilation raise was a nominal 2 m diameter and it was lined with a welded, continuous, steel liner of 1.2 m 1.D.Excavation in the glacial till was carried out with a surface bucket drill rig combined with hand mining. Ground support in the glacial till consisted of liner plates and backfill grout. The Bearpaw and Oldman formations were excavated by employing standard raise boring techniques. The individual liner sections of the continuous steel liner were assembled on surface and the entire liner column was lowered into the raise by employing hydraulic lift climbers. The liner column was back-filled with concrete.IntroductionThe Lethbridge Coal Field comprises an area of approximately 1 165 square km in the vicinity of Lethbridge in southern Alberta. Pacific Petroleums Ltd. proposed in a Preliminary Disclosure in January 1979 ""to open an experimental mine prior to development of a producing underground mine with an initial rate of 540,000 tonnes per year"". A 2 900-hectare group of leases in the Kipp-Coalhurst area was selected as the primary target for the Kipp experimental mine. The scope of work for the experimental mine included the construction of an access shaft with production capabilities, the construction of a ventilation and emergency exit raise, drive-ages in coal to yield a bulk sample, gathering of geotechnical information and the testing of experimental mining methods."

Jan 1, 1983

By R Chandramohan

Comminution is the science of size reduction of brittle materials. It is integral to mineral extraction and is one of the most energy intensive processes in the mining industry. There are a number of tests used to quantify the strength of ore, which are then used to size the AG / SAG mill in circuit design. The calculated energy utilized for breakage in these devices is based on the assumptions that the materials treated are of average shape and that the processing equipment is designed to break the ore as efficiently as possible under the given operating conditions. In drop weight tests, it was found that shape significantly influences the measured rock strength. Controlled experiments with variations in blends of rock shape show that mill throughput increases with the addition of weaker shaped rocks.

Jan 1, 2012

By M. M. O?Brien

THE SULLIVAN MINE The Sullivan mine of the Consolidated Mining and ? Smelting Company of Canada, Limited, is situated at Kimberley, B.C., nineteen miles from Cranbrook, a divisional point on the Crowsnest Pass branch of the Canadian Pacific railway. Production started on a small scale in 1900, and in 1914 the mine became the largest lead producer in Canada. In 1925 it was the largest single producer of lead and zinc in the world. Since operations commenced, 4,800,000 tons of ore have been produced from stopes and 170,000 tons from development. At the present time, ore is being mined at the rate of 1,100,000 tons per year, with a yield of about 200,000 lb. lead, 110,000 lb. zinc, and 4,000,000 oz. silver. The town of Kimberley is easily accessible by road as well as by rail. The altitude at Mark creek, a tributary of the St. Mary's river, is 3,700 feet. To th'e north of the creek, Sullivan hill rises to a height of 6,100 feet, and it is on the southern slope of this hill that the mine is located. Sullivan hill is in the Purcell range, which rises between the Rocky Mountain trench on the east and Kootenay lake on the west. It thus lies within what is commonly referred to as the East Kootenay district.

Jan 1, 1926

By F. Rivard, M. G. Drouet, W. S. Ruff, P. Carabin

"In both the hot rotary-salt-furnace (RSF) treatment of aluminum dross and the cold ball-millsieving (BMS) treatment of zinc dross, enormous amounts of energy and recoverable metal are wasted and large amounts of greenhouse gas are produced. Such wastes and the environment pollution could be avoided by using the DROSRITE PLUS™ technology. Economic and GHG production comparisons between the presently used industrial treatment processes and DROSRITE PLUS™, supported by over one hundred tests conducted in Canada, the US and Europe, are presented. The savings, with DROSRITE PLUS™, would be about $191 and $418 per MT of aluminum and zinc dross, respectively.INTRODUCTIONDross is a material, which forms on the surface of molten non-ferrous metal, such as aluminum or zinc, during melting, metal holding and handling operations when the molten metal is in contact with a reactive atmosphere. Dross normally consists of metal oxides entraining a considerable quantity of molten free (unreacted) metal, and for economic reasons it is desirable to extract the free metal before discarding the residue. In the case of aluminum dross, recovery of the metal is usually carried out by treating the dross in a furnace at a high temperature (Peterson et al., 2002). By contrast, cold zinc dross is crushed in a ball mill followed by sieving to separate the coarse metal portion from the fine oxide residue.The conventional aluminum dross treatment process, using gas or oil-heated rotary salt furnaces (RSF), is thermally inefficient and environmentally unacceptable because of the salt slag and CO2 produced from the combustion of fossil fuels. In the past several years, a number of salt-free processes have been developed and some of these have found limited commercial use (Gripenberg et al., 1994; Lavoie et al., 1990). In all these dross treatment processes, heating of the cold dross in a rotary furnace requires an external energy input that varies between 375 and 2,500 kWh per (metric) tonne of dross. Molten metal separated during processing of the heated dross is tapped, and the remaining solid residue is discharged from the furnace."

Jan 1, 2012