Search Documents

By M. S. Badollet, W. C. Streib

"AbstractA commercial method .has been developed for controlling the texture of chrysotile asbestos fibers so that they may possess properties comparable with natural sem1-harsh fibers for use in wet •processes.The physical properties of the soft, silky and slimy fibers are partially altered by a flash-heating process which removes a portion of the molecular water.The heat-treated fibers show an improvement in filterability, an increase in bulk, absorption, and surface area and better electrical properties, such as volume resistivity.IntroductionCHRYSOTILE ASBESTOS fibers are found in nature having varying degrees of texture, referred to as soft, semi-harsh, and harsh. Fibers of each type of texture have inherent characteristics which directly affect their usefulness to industry. Visual differences are apparent under a microscope where it is seen that the soft-textured fibers have a silky, serpentine or wavy appearance, whereas the harsh-textured fibers are coarser and spicular. Semi-harsh fibers, of course, have properties intermediate between these extremes.Fankuchen and Schneider ( l) have shown by the use of low-angle X-ray scattering that the diameter of the harsh type of chrysotile fiber is somewhat greater than tha of the soft variety. Surface area measurements on various chrysotiles of different textures tend to confirm their findings. By nitrogen adsorption methods, it was found that the surface areas of soft types of chrysotile asbestos are approximately 23M2 / g whereas for the harsh types they are as low as 11M2/g."

Jan 1, 1955

By Chris Dougherty

"This presentation will provide a demonstration of the methodology used in designing a modern shaft and hoisting plant utilizing a review of the challenges faced and solutions delivered for the Elk Creek Superalloy Materials Project (Niobium/Scandium). The development of the design required the review of complex hydrogeological conditions, mine production requirements, demanding capital expenditure (CAPEX) limitations and tight schedules. Through an extensive review of various alternatives to satisfy these constraints, the Nordmin Group (including Nordmin Engineering Ltd.) (Nordmin) was able to define a concept and design that addressed risks to the project, met production requirements, cost and schedule constraints and improved constructability. INTRODUCTION The Elk Creek Project, owned by NioCorp Developments Ltd. (NioCorp) presently, will become Nebraska’s first underground metals mine, built to access the Elk Creek Niobium/Scandium deposit. The development of the design for this facility required the review of challenging hydrogeological conditions, mine production requirements, demanding CAPEX limitations and tight schedules. Through an extensive review of various alternatives to satisfy these constraints, the Nordmin Group was able to define a concept and design that addressed risks to the project, met production requirements, cost and schedule constraints and improved constructability. This paper will review the challenges faced, and solutions arrived at in a demonstration of a methodology used in designing a modern shaft and hoisting plant. THE CHALLENGES Nordmin became involved in the project in 2015, invited by the Feasibility Study Consultant to provide input on estimating and layouts for the new operation. Many of the fundamental decisions regarding mining methodology, water handling and production strategy had been made, and the scope of Nordmin’s involvement was very limited in this first engagement. Following submission of that study in late 2017/early 2018, Nordmin had opportunity to discuss the overall effort, and its many assumptions and challenges, with NioCorp’s project team. The dialogue quickly identified several significant opportunities to improve the project construction schedule and costs along with the mine production profile and operational approach while reducing project risk."

Jan 1, 2019

By W. M. Brewer

Introduction This paper describes some of the mineral resources that are tributary to that portion of the Pacific Great Eastern railway included in the Western Mineral Survey District, No. 6, of British Columbia. This district extends 38 miles northerly from Squamish, the ocean terminus of the railway at the head of Howe sound, to Alta lake. Beyond Alta lake the railway continues northerly through two other mineral survey districts: the Central Mineral Survey District No. 3, and the Northeastern District No. 2. District No. 6 includes that section of the Coast Range from which the waters flow southerly towards Howe sound. The division between District No. 6 and District No. 3 is represented by an imaginary line across the summit between the headwaters of the Cheakamus river, flowing south into the Squamish, and the Green river which flows north and empties into the head of Lillooet lake near Pemberton meadows, about 20 miles from Alta lake. History: - The history of the route of the P. G. E. railway dates back to the old Cariboo days when a pack-horse trail traversed the country northerly from Squamish to the Pemberton meadows, and also south-easterly from Squamish to the head of Seymour creek, thence southerly down that creek to the north arm of Burrard inlet.

Jan 1, 1925

By G. Stenning

The paper outlines the need for high-volume ventilation in a uranium mining operation based on the design to meet environmental requirements for dust, radiation and diesel equipment. Mining methods in a highly mechanized operation, a key factor in design, are discussed. The construction and installation of major intake and exhaust fans are described briefly, together with the development of the mine airways and distribution system. Controls in the form of doors and bulkheads are important considerations in planning. Finally, the need to lower ventilation requirements in response to increasing power costs will result in future improvements.

Jan 1, 1979

By J. Talja

"Non-ferrous metal concentrates contain typically 7 – 12% water when received at the smelter. Removal of this water prior to smelting is always economically feasible because unnecessary heating of vapour (from 100 °C to 1200 °C) in the smelting furnace can thus be eliminated. This results in major reduction in CO2 emission and direct annual savings of several millions of dollars due to improved energy efficiency. Next step to further improve the energy efficiency, to gain substantial savings and simultaneously cut emissions is to select modern technology for the drying process. Consequently, all CO2 emission will be completely eliminated (from 40,000 tpy down to 0 tpy), NOx emission will be negligible, and the SO2 emission will be reduced by over 99 %. Switching of conventional direct heated drying technology to modern indirect steam drying brings, in addition to dramatic emission reduction, additional savings due to further improved energy efficiency. Direct energy savings count for 900 – 1300 MJ/t H2O, which depending on the concentrate feed rate and its moisture load can be worth several millions of dollars every year. Additional savings in operational expenses related to drying and gas cleaning may be worth a few million dollars more. Sustainability is a key issue today, and major savings together with significant emission reduction are readily available by proper technology selection for concentrate drying. INTRODUCTIONSustainability is a decisive principle in any process industry accompanied with emissions and high amount of energy. This is of significant importance in metal processing, including concentrate drying, where minimum impact on the environment, people and community are targeted, and all this with minimum cost, effort and resources. Therefore, special attention is paid to high energy efficiency, low energy consumption with preferable utilization of waste energy, safety issues, availability, level of maintenance, cost of maintenance, and emissions among other things.Non-ferrous metal concentrates can be dried using various techniques. Conventional drying based on direct heating, and use of fossil fuels for drying energy has almost entirely been replaced by steam drying. It is based on indirect heating and it has become the most dominant drying technology for copper concentrates during the last decade with over 90% of the market share of all new dryer installations. Among the steam dryers the Kumera Steam Dryer is the most pre-dominant technology with some 70% of all new dryer installations world-wide."

Jan 1, 2012

By Ralph V. Stewart

"The asbestos orebody is contained within ultrabasic rocks of Precambrian age, being located in the continuous permafrost zone of the Quebec Ungava Peninsula, some 300 miles north of the tree line at approximate latitude 61'49' and longitude 73°58'.The asbestos deposit is at the western tip of a folded ultrabasic sill complex which trends northeast and covers an elliptical area 4.5 miles wide by 15 miles long. Locally. the asbestos occurs in. a completely serpentinized dunite rock. The principal rock types in the vicinity of the ore-body originally consisted of dunite, peridotite and pyroxenite, all of which have experienced at least two periods of alteration, so that no fresh rock now remains.The main ore zone in the open pit is approximately one quarter mile in length, 150 to 200 feet in width, and plunges at 25 to 30 degrees in a northeast direction below surface, to a vertical depth of at least 1,200 feet, Consider¬able tectonic activity resulted in favourable structural conditions which culminated in the formation of the ore zone in its present form.The deposit consists principally of cross-fibre ""gash type"" veins which vary in length from several inches to several feet. The principal fibre vein direction is parallel to the dip of the enclosing serpentinized dunite and sill complex.Some of the problems encountered during diamond drill¬ing in permafrost are briefly discussed."

Jan 1, 1976

By Ian M. F. Arnold

"Occupational health programs and their role in improving the quality of working life in the mining industry are discussed. Attention is directed to some problems peculiar to the Canadian mining industry. Factors affecting program development are reviewed, as well as parameters affecting cost-benefit analyses.IntroductionThe quality of working life in the mining industry is a more important consideration than in many other industrial environments because of the very nature of the undertaking. It was a strange paradox of the 1960s that preventive maintenance programs for machinery and equipment were well accepted, whereas the concept of ""preventive people medicine"" was basically ignored. Fortunately, there seems to be a swing toward the development of occupational health programs in many sectors of the business community; however, there is a noticeable lack of consistency and uniformity for thought among the members of the mining industry. The blame for this lack o f progress in the occupational field cannot be entirely attributed to the industry, but must also rest with (for the most part) apathetic and inadequately trained physicians. This latter problem is slowly improving with the growing recognition that a well-planned and executed occupational health program may improve the quality of working life for mining employees and their families.There are a number of factors which relate to occupational health in mining, and its effect on working life quality. Included among these are:1. Community isolation.2. High accident risks.3. Occupational disease risks.4. Production demands and the state of the economy.5. Government regulatory requirements.6. Travel demands.These, and others, reflect on all levels of the mining industry. To examine how these factors can be moderated by an occupational health program, it is necessary to first review the rationale for such a program and some of the costs related to it."

Jan 1, 1983

By G. G. Richards, Y. Oyediran, V. Chow

The oxygen softening process for partial removal of arsenic and antimony from lead bullion has been in use at Teck Cominco's Trail smelter since 1986. In this process, industrial oxygen is injected into bullion to remove As and Sb with the formation of an oxide slag. In Trail, the levels of these elements are reduced to concentrations suitable for processing in the Betts electrorefining plant. Recent moves toward the treatment of higher arsenic-bearing feeds have necessitated an increase in the process capacity to meet the specifications for drossing plant bullion. Process intensification trials were conducted in-plant to develop an operating strategy for higher bullion processing rates. This was preceded by a study conducted with McGill University to develop a fundamental understanding of the therm ochemistry and kinetics of the process. The results have yielded more effective control of the operation, and identified opportunities for further improvements.

Jan 1, 2008

By S. Mao

Total station has been predominantly applied in stationary survey scenarios in construction. With the moving target tracking and point survey automation functions, a robotic total station (RTS) lends itself well to more dynamic applications. Nevertheless, a RTS unit is still unable to track multiple targets simultaneously or to survey a target point when the line-of-sight is temporarily unavailable. In this paper, we propose a methodology to synchronize and automate multiple RTS units intended to address dynamic tracking and surveying applications in the construction field. By using the application programming interface (API) from the manufacturer, we implement the proposed methodology and the prototype system integrates two RTS units in regard to space and time and communicates survey command instructions among RTS units through wireless networks. The two RTS units can be operated to survey the two ends of one swinging sling concurrently in order to retrieve the actual length of the sling within several millimeters accuracy. Besides, in applications where line-of-sight between a target object and one RTS unit cannot be guaranteed all the time, continuous surveying can be materialized by automatically delegating the task to another synchronized RTS unit with clear view of the target object. A field test was conducted to demonstrate the application of the proposed automation approach in which sling length was measured of a rigging framework used for lifting industrial modules. The testing results are presented and achievable accuracy and reliability are discussed. The proposed solution overcomes the limitations of global positioning system (GPS) and laser scanning and holds high potential to provide cost effective solutions to many dynamic field applications.

Aug 1, 2013

By Z. S. Shao, X. Z. Li

"Sub-critical crack growth plays an important role in long-term creep failure in brittle rock. Based on micromechanics established by using relationship between micromechanical wing crack growth model and macroscopic strain, and comparing theoretical model with testing results, a method, which applies the theory to real rock, is suggested in this paper. Using this method, properties of creep, damage and progressive failure in brittle rock are investigated. Effects of stress state on creep failure time and steady-state creep rate are analyzed and graphically presented. The results are helpful to support structure design and service life evaluation of underground structures with high geostatic stresses. INTRODUCTIONDuring the long-term operation in underground space with brittle surrounding rock, due to chemical action between pore water and rock, the failure of rock often occurs at stresses below its short-term failure strength, which brings serious effect on the long-term stability of underground structure. Thus, the long-term strength of brittle rock attracted wide interests of scholars around the world. The static fatigue limit was predicted by exponential function that is derived from abundant experiment data of stress level and failure time(Schmidtke & Lajtai, 1985), and similar result by relationship between stress state and failure time was also suggested (Lau & Chandler, 2004; Aubertin et al., 2000; Sangha & Dhir, 1972). According to relationship between steady creep rate and stress state during creep, a critical stress that transforms steady-state creep to accelerated creep was studied and the long-term strength was suggested (Tsai et al., 2008; Ma & Daemen, 2006; Lajtai et al., 1991). Based on the results of experiment in compression, the long-term strength of rock was defined by stress at volume strain reversal. When applied stresses are larger than the long-term strength, the microcracks in the rock will grow constantly, damage of rock will increase and failure of rock will occur finally (Chandler, 2013; Bieniawski, 1967; Brace et al., 1966)."

Jan 1, 2015

By A. J. Stapleton

"The Copper Mountain mine of Gaspe Copper Mines, Limited was brought into production in January, 1968.This paper describes the organization, scheduling and control of maintenance of large open-pit equipment, including 8-cu.yd shovels and 85-ton electric-wheel haulage units. The facilities for repair as well as maintenance are also described, including repair shops and field repair equipment. Maintenance costs are discussed and particular reference is made to tire inspection, records and costs."

Jan 1, 1969

By A. K. Ratte, C. M. Brown

"IntroductionIn autogenous mills, grinding of the ore feed is accomplished by the direct action of the variously sized rocks making up the feed on each other and the mill interior. Size reduction is achieved without the addition of grinding media foreign to the mill feed, differing in this respect from rod, ball, and pebble milling. The term ""semi-autogenous"" has entered common usage in the industry to describe autogenous mills to which supplementary grinding ball additions are made to increase the rate at which size reduction of the mill feed occurs, beyond that achieved solely by the action of rock on rock. In a semi-autogenous grinding (SAG) mill, 50Jo to 10% of the mill volume may be occupied by grinding balls, whereas a range of 25% to 45% is more usual in ball milling.The comminution of mineral ores using ""conventional"" techniques has been described in previous papers. In conventional operations, size reduction of mined ore, and liberation of the valuable mineral content, is typically accomplished using flowsheets employing two to four stages of crushing. Crushing is followed by one to three stages of grinding and classification using various combinations of rod, ball, and pebble mills. This paper describes operations employing autogenous or semiautogenous grinding as the principal stage in the comminution process. Primary crusher discharge, or in some instances run of mine ore, is fed directly to an autogenous or semi-autogenous grinding circuit. Final product sizing may be accomplished in a single grinding stage, the mills operating in closed circuit with classification equipment, or in several stages using autogenous and semi-autogenous mills for primary grinding, and ball or pebble mills for secondary grinding. In several operations a portion of the primary mill discharge is crushed in an intermediate comminution step, these circuits being called autogenousball- crusher circuits (ABC). Many different flowsheets exist, but common and important to most are crushed ore stockpiles, reclaim feeder and mill feed conveyor systems, pumps, screens, and classifiers. Autogenous grinding is employed in both wet and dry processes, although today wet predominate."

Jan 1, 1989

By D. H. Ryan, J. T. Graham, A. Navarra, J. A. Finch, S. Somot

Pyrrhotite (Po) is widely considered to be the most significant mineral in the self-heating of sulphides. It is therefore desirable to determine the amount of Po in mineral samples. This is commonly accomplished through x-ray diffraction (XRD) or quantitative evaluation of materials by scanning electron microscopy (QEM-SEM). This paper introduces another quantitative method based on Mossbauer analysis that requires limited sample preparation and has the additional potential to detect the sulphur/iron ratio within Po. The technique is explored using pentlandite/pyrrhotite mixtures.

Jan 1, 2009

By R. K. Rajamani

Discrete Element Method simulation of charge motion in ball, SAG and autogenous mills has become a standard for design of mill internals, power draft evaluation, etc. Both two-dimensional and three-dimensional codes are being used. The two-dimensional code dominates the user market since the code completes a simulation in one or two hours. On the other hand, three-dimensional codes have been in the domain of specialists who can handle the complexity of the code and have access to parallel computing hardware. For the first time, this barrier is overcome via computing with graphic processing units (GPU). Commodity graphics cards now allow parallel computation with hundreds of processors. It is shown that the computational time has been reduced by a factor of fifty using GPU computing. Hence, SAG charge simulation results in three dimensions are achievable in a few hours using affordable desktop machines. The GPU computing shown here enables the three dimensional simulation into a manageable daily task for mill designers and researchers. On the technical side, the simulations can be elevated to a higher level of complexity to simulate breakage and transport. First, the speedup factor of fifty is established for the Nvidia GeForce GTX 580 graphics card. Next, four simulation tasks, consisting of AG, SAG and ball mills are reported. The simulation of AG and SAG mills are completed in less than 8 hours. The ball mill simulation with 1.25 million spheres is completed in 27 hours. In the near future, as the graphic card hardware advances the compute time can be halved.

Jan 1, 2012

The primary (sulphide) resources at Aphrodite are refractory in nature, requiring an oxidation process stage to be introduced to facilitate extraction of the gold. The company is investigating the use of pressure oxidation (POX) as the oxidation method for processing of high grade gold bearing concentrate it plans to produce at Aphrodite. POX has been used extensively around the world for the past 30 years and continues to be the favoured option for a number of refractory gold plants currently in the design and construction stages. Initial pressure oxidisation testing investigated the effect of temperature, pressure and grind size on a bulk flotation concentrate prepared from Alpha lode material. The concentrate averaged 47.3 g/t gold and was prepared from a composite of core samples averaging 1.49 g/t gold. Sub-samples of the concentrate were subjected to POX for 1 hour resulting in rapid oxidation during this very short period. Testing undertaken showed that there was a significant increase in sulphide oxidisation at higher temperature (220°C) and pressure (2,500 k/Pa) for the two grind sizes (75 and 20 microns) evaluated. The proposed flowsheet, OPEX and CAPEX are critical aspects for project development.

Jan 1, 2014

By M. B. McClenaghan

"Abstract - The Matheson area of northeastern Ontario is of great interest for mineral explo­ ration because of its geological similarities with the adjacent Timmins, Kirkland Lake and Larder Lake gold camps. Exploration in the area, however, is hampered by the presence of an extensive and thick cover of glacial sediments. For this reason, till geochemistry has be­ come an important exploration method. The Ontario Geological Survey&apos;s Black River -Matheson (BRiM) reconnaissance till sampling project, carried out between 1984 and 1988, was designed to aid exploration in the Matheson area by documenting the Quaternary stratigraphy and providing a database of till geochemistry. Till samples were collected by backhoe trenching of surface pits in areas of thin drift ( < 5 m) and by sonic overburden drilling in areas of thicker drift. This paper summarizes the results from the shallow till sampling component of the BRiM project.Two hundred and eighty-two surface samples were collected from Matheson Till, the youngest till sheet in the area, which was deposited during the Late Wisconsinan. For each sample, the non-magnetic heavy mineral (>3.3 S.G.) and fine (-250 mesh) till fractions were analyzed geochemically. In addition, visible gold grains were recovered by panning the heavy mineral fraction. Five areas that display multi-element anomalies in both till fractions warrant further investigation: (1) western Egan Township, overlying the Bradley Lake Syenite; (2) around and south of the Munro and Croesus mines, in Munro and Guibord townships; (3) central Garrison Township overlying the Garrison Stock; (4) south of Ore Car Lake in northern Thackeray Township; and (5) southeastern Harker Township. In these areas, Matheson Till has a local provenance and the bedrock sources for these anomalies are nearby in the up-ice (north­ northwest) direction. Due to the fine-grained nature of gold in bedrock deposits in the BRiM area, the small size of most gold grains recovered from till samples (<50 1-1m) and the variable distribution of gold in the heavy mineral concentrate and fine fractions, the fine fraction in addition to the more commonly used heavy mineral concentrate should be used for gold exploration.Surface till samples have been affected by weathering to a depth of s3 m. Weathered till is characterized by a very low carbonate content in the matrix fraction, the absence of sulfide grains in the heavy mineral concentrate and higher concentrations of copper, nickel and zinc in the fine fraction than in the heavy mineral concentrate. As a result of the weathered/ oxidized nature of the surface till samples, the fine fraction is a better sampling medium for base metal exploration."

Jan 1, 1992

By N. Melnyk, H W. Habgood

The conventional low temperature process for extracting' helium from natural gas involves liquefying the whole gas stream in order to remove the relatively small fraction of helium. A process based on the selective diffusion of helium through a semi-permeable barrier is, in principle, more economical and flexible, particularly for the treatment of small re-serves and low concentrations. The well-known permeability of glass to helium offers the possibility of such a diffusion process and McAfee of the Bell telephone Laboratories showed in 1958 that practical separations could be achieved by passing natural gas over bundles of fine capillary glass tubing. Developmental studies have been carried out involving larger units and more extended field tests than those of McAfee. Fine capillary tubing of Pyrex glass 0.0035 in. diameter was prepared by drawing ordinary 6 mm. laboratory tubing in a furnace. Extraction units were pre-pared containing about 10,000 such tubes, 4 ft. long and cemented inside

Jan 1, 1961

By The Staff

WE were requested to make a digest of our original grinding report, Fine Grinding Investigations at Lake Shore Mines. This digest is much easier to read than the original report, but it lacks the experimental &apos;evidence&apos; found in the first report which, in many cases, is much more interesting and educational than the conclusions derived from it. In the course of rewriting the paper, we noticed several new angles on the test data which had not occurred to us previously. From the data included in the report and other tests not published, calculations were made which indicated a line of new test work. These tests, among other things, more than suggest a technique for designing the length of mills, the position and number of classifiers, and the total loads a mill should carry.

Jan 1, 1941

By D. G. F. Hedley, F. Grant

"In 1958, the Ontario Department of Mines appointed a committee to study the accident situation and mining methods used in the uranium mines in the E1liot Lake district. This committee reviewed the existing knowledge on mine design, pillar support and roof spans and came to the conclusion that scientific knowledge had not yet reached the stage of producing rational design procedures which would reduce the dependence on trial-and-error methods. Since that time, the Mining Research Centre has made numerous stress measurements in two mines to define the pre-mining and pillar stresses. A comprehensive series of tests has been done in the laboratory to measure the compressive strength of the rock; a geological survey of the region has been made to evaluate tectonic stresses; and a survey was done on mining conditions with regard to stable and unstable pillar configurations. This information has been used to evaluate pillar design as effected by pillar width and height, depth below surface, extraction and pre-mining stress fields. The resultant design of pillar widths and corresponding extraction as the depth increased is in line with past and present experience in these mines. The information available on roof stability is still insufficient to design stable stope spans with the same degree of confidence; experience and trial-and-error methods are still required."

Jan 1, 1972

By H. A. Gorrell, S. R. L. Harding

"The potash beds in the Saskatchewan portion of the Williston Basin occur in the upper portion of the Prairie Evaporite formation of the Devonian Elk Point Group. They represent the late stage of a major evaporitic cycle. Two other evaporitic cycles are known in overlying beds, but these apparently never reached the stage of potash salt deposition. The basin in which salt deposition took place extended from the northwestern corner of Alberta southeastward across Saskatchewan into Manitoba, North Dakota and Montana. Deposition of potash salts was apparently restricted to the southeastern portion of the evaporite basin. On a regional basis, five major stratigraphie divisions of the potash-bearing strata have been made. Locally, several of these units may be divided into correlatable sub-units. The potash-bearing strata are separated and overlain by predominantly halite layers of varying thickness. Cross sections show the regional correlation of the potash-rich zones, and maps show the present distribution of the individual potash-bearing zones and the areas of richer development for each zone. The maps tend to substantiate the interpretation of considerable subsurface solution of salt and potash beds."

Jan 1, 1967