Search Documents

By J. Visman

"SummaryThis paper is presented as part of a programme to show the steps taken by industry and others interested in supplying a solid fuel of constant quality to 'satisfy a consuming market. The paper deals with the general principles underlying quality control in coal preparation plants, namely, constant quality and close adherance to acceptance limits. It also describes how control of ash content is ""generally hampered by the problem of coal sampling .and the long duration of the ash analysis and how these difficulties may be overcome.Quality control can be effected in several ways. Thorough blending wll reduce variations appreciably, except those of long trend. The latter can be detected by automatic sampling and quick ash analysis. At present, under favourable conditions, a system of half-hourly ash determinations with an accuracy of 0.5 to 1.0 per cent can be realized, to the effect that trends with a 'wave length' of more than two hours cu be eliminated within the limits of accuracy of the ash figures. The general solution of the problem is a combination of blending, accurate sampling, quick ash determination, and statistical analysis of the pattern of ash distribution.The use of statistical methods of analysis, such as the t test and F test, is •discussed at some length in order to emphasize the importance of the correct evaluation of observational data if there is to be confidence in the validity of test results.General ConsiderationsCOAL, as a fuel, is too cheap for a long haul across the country. The limiting distance depends on the price of the local competitive fuels, and, as the price depends to a great extent on quality, so does quality, to the same extent, command the market."

Jan 1, 1952

By K. J. Daun, C. J. Shi

UsiborThrough the second step heating at 900 °C, the spectral emissivity shows a gradually decreasing trend with increasing soak time, caused by the surface phase transformation from Al® 1500P coupons are austenitized in a Gleeble 3500 thermomechanical simulator using a two-step heating procedure in an argon atmosphere. Variations in spectral emissivity are measured in-situ using a near infrared spectrometer and ex-situ with a Fourier transform infrared reflectometer. Microstructural evolution and surface roughness are investigated using optical microscopy, FE-scanning electron microscopy, and a surface profilometer. A series of phase transformations of Al-Fe-Si intermetallic phases at the coating/steel substrate interface cause the surface phase and surface roughness to change, which in turn influences the spectral emissivity. At the beginning of the first heating step, the coupons have very low spectral emissivity, due to the molten Al-Si coating. Spectral emissivity increases significantly with increasing soak time from 5 to 12 minutes, associated with the surface phase transformation of the coating into Al7Fe2Si intermetallic phase and an increase in surface roughness. 5Fe2 into AlFe intermetallic phase with a decrease in surface roughness.

Jan 1, 2015

By L. Ferland, D. LaRonde, J. C. Caron

"The free-world production of columbium ore concentrates has doubled in the last five years. St. Lawrence Columbium and Metals. Corporation has contributed largely to this expansion, its production rate increasing from 720 tons of concentrates per year in 1961 to 2 200 tons in 1965.To follow the normal market development, the Company initiated an engineering study aimed at establishing the most economical mining methods, thus permitting it to increase its milling rate from 1,000 tpd in 1964 to 2,000 tpd in 1967 and possibly to 3,000 tpd in 1968. The results of this study pointed out the advantages to be gained in converting from an open pit to an under-ground operation. This paper describes how the mining engineering department has successfully developed ""stopes"" from the walls of its No. 2 open pit, in order to assure continuity of its operation during the interval required to develop its underground mine."

Jan 1, 1967

By G Anders

The mucking out of sub-level headings by slusher and by Autoloader is described, and the performance and costs of both methods are compared. The introduction of the Autoloader is taken as an example to illustrate the meth-od used at the mine for evaluating the suitability of new equipment. The consecutive steps in the process are covered in detail -from the preliminary cost analysis and the preliminary estimate of savings and advantages, and the review of these data after a field investigation, through the elimination of dubious factors, and detailed time and performance studies at the property, to the final assessment of the new equipment and an evaluation of the initial forecast. The Autoloader in Operation. 1198 Introduction AT Mattagami Lake Mines Ltd., the mine workings are laid out basically on a pattern of 60-ft.-wide stapes alternating with 60-ft.-wide pillars, with stope lengths varying from 80 to 200 ft. and stope tonnages generally between 80,000 and 200,000 tons. Stapes are drilled off from sub-levels at 60-ft. intervals, with the

Jan 1, 1965

By Frank D. Adams

The Island of Ceylon, which is one of the most beautiful possessions of the British Empire, has been an abode of man from the very earliest times. The Veddhas, a wild tribe of some 4500 people still living in the fastnesses of the jungle in east central portion of the island, are believed to represent a remnant of the oldest inhabitants of which we have any actual knowledge, but in the caves in which they live there are found the stone axes and other implements of Palaeolithic people who represent the first race of men who inhabited our globe, and of whom they may be, for all that is known, the direct descendants. About the fifth century before Christ there came the Aryan invaders, apparently from the north of India, who drove the Veddhas into the remote fastnesses of the jungle and developed the remarkable Singhalese civilization whose high character is demonstrated by the remarkable and very extensive system of irrigation works which they built up, and through which they made the island wonderfully productive. Great cities arose, some of which are believed to have had a population of over a million souls and whose temples and public buildings show that the people were accomplished architects and sculptors.

Jan 1, 1926

By R. L. Dunsmore

Introduction If one had been called upon to describe petroleum oil refining seventy-five years ago, he could have acceded to the request quite satisfactorily in about fifteen minutes. Fifteen years ago, an hour and a half would have been sufficient to give a general idea of oil refining, and of the equipment used for this purpose. Today, so extensive has been the research into all phases of the refining and manufacturing of petroleum products, and so rapid the strides in improvement in technique and equipment, that I doubt if a week would suffice to give an adequate outline of ail the ramifications of present-day oil refining. I propose to only 'hit the high spots', dealing particularly with the equipment and methods employed at the Imperoyal refinery, which you are to visit. Crude oil, the refiner's raw material, contains essentially only two elements, hydrogen and carbon. These are not present in the free state but are combined in various proportions as 'hydrocarbons'. A given crude oil is not made up of just one hydrocarbon, but of myriads; some solid, others liquid, and still others gaseous at atmospheric temperature and pressure, ail dissolved one in the other. Moreover, the nature and the relative amounts of the several hydrocarbons vary very considerably in crude oils from different sources. That is, a 'crude' from Oklahoma will contain hydrocarbons not present in crude from Mexico, and is different again from the Venezuela crude. Not only this but oil in a certain well in, say, Peru may be differently constituted from that in a well half a mile distant from it.

Jan 1, 1931

By Walter Herd

For the past eight years, No. 2 mine of the Cumberland Railway & Coal Co., Springhill-a subsidiary of the Dominion Coal Co., Ltd.-has had an unenviable reputation for bumps. As the workings extended in certain directions under a greater cover, these bumps increased in severity and it became apparent some change in the system of extraction was necessary if the mine was to continue to operate. In September, 1924, following several fatalities resulting from bumps, the Mines Depart~ of Nova Scotia requested from the U. S. Bureau of Mines the services of George S. Rice, Chief Mining Engineer of the Bureau, to report on the conditions then prevalent in No. 2 mine, Springhill. °This request was promptly and courteously granted. Mr. Rice made a full investigation and a comprehensive and helpful report, which is embodied in the 1924 Annual Report of the Department of Public Works and Mines, Nova Scotia. Prior to 1925, the room-and-pillar method was employed, and in January of that year (there being a cessation of work from March to August due to labour troubles) longwall retreating on the west side, on a limited scale, and in a small section on the east side of the mine, was started. The major portion of the east side was not operated on this system till August, 1926, as there was developed a considerable area ready for pillar extraction between an arbitrary boundary and a point up to which bumps of any consequence had not been experienced. In ?the interval, development work for longwall retreating below the 5,900-foot level was vigorously pushed.

Jan 1, 1929

By T. H. Janes

THE POSSIBILITY of producing pig iron from iron ores of British Columbia for a west coast primary iron and steel industry has been investigated by the provincial government and by commercial interests on sever.al -occasions. The latest study is that currently under way by The Consolidated Mining and Smelting Company of Canada, Limited. The Company is studying the possibility of making pig iron from the oxide calcine resulting from the roasting of pyrrhotite. tailings used in making sulphuric acid for fertilizer production at Kimberley. A comprehensive report on the subject .of establishing a primary iron and steel works in the Province, based on local iron ores, was prepared by Arthur G. Mc-Kee and Company of Cleveland, Ohio, in 1942 for the B.C. Minister of Mines and is available to interested parties. A detailed survey on the subject was also pre-pared in 1954 by Dr. G. P. Con-tractor, then .of the British Columbia Research Council. Considerable information is there-fore available on most aspects of an integrated primary iron and steel industry in British Columbia to supply the needs of the western provinces. To date, however, no basic iron industry has been established despite the .occurrence of high-grade iron ore deposits on the offshore islands and the high freight charges on iron and steel products brought into the area from Eastern Canada and overseas producers. The chief deterrent has always been the relatively small and highly diversified market available to a local steel producer. Other major fact-ors have been the lack of sufficient proven reserves of iron ore, and the difficulty of making pig iron, suit-able for steel manufacture, economically on a small scale. Technical and economic conditions have changed considerably since World War II and the establishment of a primary industry based on electric furnace production of pig iron or on one of the direct reduction processes, coupled with electric furnace steel production, may now be economically feasible.

Jan 1, 1958

By W. Geslin

Backward extrusion process is a metal forming process, which limits the manufacturing?s extra thickness when compared with classical die forging technique. Because of a lack of alloy?s mechanical behavior knowledge, the basic strategy of design is as follow: ?Definition of a small scale blank ?Performing experiment in order to get useful process data ?Improvement finite element simulation conditions ?Development of the full scale blank forming process (design of tools,...) using the finite element simulation A comparison between the result of modeling and the experimental data has been done to validate the finite element simulation.

Aug 1, 2010

By John Convey

This short paper deals with the subject of research and its relation to productivity. All who have stopped to even think about industrial re-search and its impact on the nation-al economy take for granted that research and development are pre-requisite to increased productivity. It is another matter, however, to identify and properly evaluate the many factors entering into the relationship between the two. Some studies are currently underway in the United States on the subject, but, so far, nothing much in the way of conclusive data has come to light. In Canada, we have not yet even produced any statistical figures on national productivity, although work is now being done on this subject and information will soon be available. The usefulness of being able to measure the benefits of investment in re-search and development in terms of industrial growth or productivity need not be laboured for the benefit of those interested in research management.

Jan 1, 1964

By K. van Warmerdam, M. Pearson, C. Kember, D. McMullen, M. Thayer, C. Ugarenko

In July 2012, Hatch Ltd. and Air Products & Chemicals Inc. completed construction and commissioning of a 4000 tpd O2 cryogenic air separation unit (ASU) for Barrick Gold’s Pueblo Viejo Project located in central Dominican Republic. The ASU produces high pressure gaseous oxygen, which is used for the oxidation of refractory sulphide ore within the pressure oxidation (POX) circuit. As a result of the project’s remote location and tropical climate, many challenges were faced over the course of construction, commissioning and start-up of the ASU. These challenges included adequate preservation of equipment due to dusty and humid site conditions, final assembly and erection of the cryogenic distillation columns on site, limited spare parts inventory/availability, and an unfinished power source for plant commissioning. This paper discusses the steps taken by Hatch and Air Products to successfully design, construct, commission and start up the largest stand-alone ASU plant for a POX application in the metallurgical industry.

Jan 1, 2014

By Wm Petruk

"The tungsten-bismuth-molybdenum deposit in southwestern New Brunswick occurs in greisenized and silicified tuffite * and feldspar porphyry in and adjacent to volcanic necks. The ore minerals occur as veins and veinlets and as disseminated grains in gangue. These minerals can be grouped into three assemblages. Assemblage 1 consists of oxides and phosphates of W, Ti, Fe, Nb, Sn, Ta and rare-earth elements, with the main minerals being deposited in the sequence wolframite, rutile, cassiterite. Assemblage 2 consists of arsenopyrite, molybdenite and bismuth, and assemblage 3 of sulphides with minor cassiterite and arsenopyrite. Sphalerite is the main sulphide mineral, but it contains minute inclusions of copper-tin- and indium-bearing minerals. Textural relations suggest that most of the elements can be recovered from this ore by conventional mineral beneficiation and extraction methods, but a variety of techniques must be employed. It is expected that the wolframite and molybdenite can be recovered satisfactorily, but poor recoveries are expected for bismuth and cassiterite. A sphalerite concentrate can be readily obtained by flotation, but it would contain a wide variety of elements. It is suggested that leaching be used to recover the bismuth and the elements in the sphalerite concentrate."

Jan 1, 1973

By Bunting S. Crocker

This paper reviews the trends in the past two years in autogenous grinding throughout the world. It covers rock grinding in South Africa, Sweden, Canada, the United States, Finland and Germany. To properly orient the discussion on this subject, the paper attempts to define and classify the scope of autogenous comminution. As this is a relatively new subject, there is often considerable confusion regarding the various practices, which sometimes differ widely. By clarifying the types and forms, we hope to help clear up this con-fusion. Autogenous grinding is being carried out, throughout the world, either in mills grinding in water or solution or in dry mills using air classification to remove the finished material. The wet grinding, particularly, can be divided into: (1) (2) (3) Primary autogenous grinding, or "run-of-mine" grinding. Secondary autogenous grinding or semi-autogenous grinding or rock pebble grinding. Combination processes. -This covers plants in which pebbles made in the primary mill are re-moved and used as grinding media for fine grinding in secondary mills.

Jan 1, 1963

By Richard R. Walker, John J. Watkins, Allen C. Amos, Matulich. Angelo

THE KIDD CREEK MINE is located within the Abitibi greenstone belt, near its west end, in an area known as the Porcupine mining camp (Fig. 5). The Abitibi belt, long known for its many major gold and base metal deposits, is the largest Archean (early Precambrian) greenstone belt within the Canadian Shield. In the Porcupine area, the greenstone belt is composed principally of Keewatin (older Archean) basic to intermediate volcanics, with subordinate felsic volcanics developed• locally. Greywacke, mainly of volcanic derivation, occurs associated with and overlying these volcanics. Timiskaming (younger Archean) sediments, principally coarse clastics, unconformably overlie the Keewatin volcanics and sediments. The reader is referred to Goodwin and Ridler (1970) •r. for a more comprehensive description of the Abitibi belt.

Jan 1, 1974

"Liberation is a key requirement for efficient separation in mineral processing. As a consequence of this an understanding of the inherent textural features of an ore is no longer possible since during the process of liberation, texture is destroyed. Knowledge of key textural features, such as mineral grain size and distribution, prior to breakage processes provides the opportunity to understand the textural drivers for ore hardness. Modern characterisation methods, including automated SEM-based techniques, provide the possibility of measuring mineral characteristics at a range of scales. This paper discusses how textural features of two different ore types in a porphyry copper deposit can be measured and interpreted at a number of scales. Standard breakage tests conducted on the ores indicate that one of the ores can be characterised as hard and the other as soft. The impact of mineral grain size and the presence and scale of vein type structures in the two ores have been used to determine the extent to which these features influence ore hardness.INTRODUCTIONIn order to effectively convert ore into metal, knowledge of both the processing stages and the characteristics of the ore are essential. Prior to the advent of technologies that enabled the fundamental understanding of the sub-process at each stage of processing and the measurement of appropriate ore properties the most effective way to understand how an ore would respond to a process was to put it through that process, for example the way to determine how an ore would break was to first break it. Existing comminution models seek to predict the size distribution of rock fragments as the result of applied energy based on knowledge of the rock strength. It is common for these models to consider the rock as homogeneous and despite providing important data for the design and optimisation of industrial comminution circuits these models are only applicable within a narrow range of operation. In order for reliable predictive models to be developed that account for the inherent ore characteristics, a step change is required in the type of measurements that are carried out to characterise an ore and the type of data that is extracted and used as model inputs."

Jan 1, 2016

By J. H. McKibbon

THE metallurgical industry has purchased more than sixty per cent of the industrial gas cleaning equipment installed in Canada. This includes cyclonic collectors, scrubbers, cloth filters and Cottrell Precipitators. These are the principal types of equipment which are used commercially for the cleaning of gases which result from the processing of iron, nickel, copper, lead, zinc, gold, gypsum and aluminum ores. The recovered dust, which usually contains metal values, is returned to the process. The cost of the equipment is thus economically justified. This is in contrast to other industries, such as those involving steam power generation, asbestos, cement and lime production, where, though dust collection equipment is extensively used, it is installed primarily for nuisance abatement. Communities are becoming more and more conscious of air pollution, new and more stringent legislation is being enacted, and, for other than economic reasons the smelting industry will eventually be required to install more efficient gas cleaning equipment. This paper

Jan 1, 1962

By Heribert F. Broicher

By the very nature of mineral deposits the quality of the raw material generally fluctuates and should be known for optimum processing. Early classification, for example, of limestone into road-metal grade or lime grade or of run-of-mine ores into high grade, low grade and waste as well as information for blending or for dosage of reagents are prerequisite for economic processing. Non-contact, real-time and on-line rock identification or assessment of quality parameters can be realised by introducing the analysis of laser-induced fluorescence (LIF) into the mining industry. LIF analysis is an optical method evaluating the basically known photoluminescence properties of matter, however, extending the application into hitherto unimagined fields by use of high-energy pulsed lasers and time-resolved analysis of fluorescence in the ultra-violet, the visible and near-infrared domains of light. LIF analysers and test work in a limestone quarry and a cement plant in Germany as well as in an iron ore mine in Sweden are described. First results of test work are available and proof this technology to be promissing.

May 1, 2002

By Adrian Dance

Barrick Gold Corporation?s wholly owned subsidiary, Barrick (Granny Smith) Pty. Ltd. operates the Granny Smith operation in Western Australia and has been operating a SAG/ball mill (SABC) circuit for a number of years processing a blend of secondary crushed, open pit and underground material. With closure of the open pit in 2008, Granny Smith was considering different options to process underground only material at a lower throughput. Using the existing equipment available on site, a number of circuits were evaluated by Metso Process Technology & Innovation (PTI) through modelling and simulation. A single stage SAG mill circuit was selected based on power requirements and operating efficiency. In April 2008, Granny Smith started operating their SAG mill in single stage, processing primary crushed feed and using their existing pebble crusher for scats. Smaller cyclones were used to control the final grind size. PTI surveyed the new single stage circuit in July 2008 under normal and high rock load conditions to show the effect on final grind size. Granny Smith continued to operate this circuit until the end of 2009, when alternate feed sources resulted in a return to the complete SABC circuit at a higher tonnage once again. The variable speed, single stage SAG mill proved itself to be very efficient and flexible option to process the hard underground Wallaby Deeps material. This paper will review circuit performance following the conversion to single stage in comparison with the full SABC circuit.

Jan 1, 2012

By S. A. Luciani

"In 1957, an asbestos orebody was discovered in the northern sector of the Ungava Peninsula of the Province of Quebec, an area now identified as Asbestos Hill. The deposit is situated on a plateau 1700 feet above sea level and 42 miles inland from Hudson Strait. It is a bleak, iso. lated location of typical arctic environment. Fifteen years were to pass before the first shipment of ungraded fibre was made in 1972. These years we1•e occupied with field surveys and investigations, diamond drilling, engineering design, evaluation of investment and operating costs, and construction. The problems normally associated with mine development were further complicated by location, isolation, and the extreme cold and permanently frozen ground of the arctic regions. Unique to an isolated arctic operation are the organization of support facilities and services, procurement and retention of personnel, construction of access roads and airports, and scheduling of product out and supplies in during the short summer period of sea navigation."

Jan 1, 1976

By J M. Anderson

The cable belt conveyor installation at Craigmont Mines Limited, Merritt, B.C., has the greatest one-stage vertical fall of any conveyor installed overland in Canada. Since the late summer of 1961, this conveyor has carried more than 5,000,000 tons of copper ore from open pit to concentrator site. When the conveyor is loaded, the drive motor acts as an induction generator, delivering power to an external circuit. This paper covers the selection, the operation, the performance statistics, and the installation and operating costs of this conveyor system. Introduction T HE Craigmont mine is located in the south-western interior region of the Province of British Columbia, approximately 240 miles northeast of Vancouver. A moderate climate, good roads, service by the Canadian Pacific Railroad, power from the British Columbia Hydro Authority, gas from the nearby main line of the Inland Natural Gas Company and close proximity to the village of Merritt provide a favourable location for this mining operation. The ore occurrences at Craigmont have a vertical extent of 1,500 feet,

Jan 1, 1965