Search Documents

By CH. Liu, H. X. Jiang, X. Xiao

"A study has been conducted to characterize the fatigue life in 7050-T7451 thick plate by the comparison between an experimental alloy and commercial alloy. The fracture origins were specified and their sizes were measured by scanning electron microscope (SEM). Additionally, the size, number density and spatial distribution of porosity in the experimental material and commercial material were characterized and compared, using X-ray Computed Tomography(XCT). The results showed that microporosity was the predominant site for crack nucleation and subsequent failure of the experimental alloy. However, as for the commercial alloy, fatigue cracks were found to originate from constituent particles. The presence of microporosity in 7050-T7451 thick plate reduced fatigue life of an order of magnitude or more compared to the commercial alloy. The relationships between size of origin and fatigue life were proposed. It was showed that the fatigue endurance was reduced when the size of porosity increased.INTRODUCTION 7xxx series aluminum alloys, due to their combination of high strength, high resistance to stress corrosion cracking, and good fracture toughness, are widely used in structural engineering applications where high-strength and low-density characteristics are fundamental design requirements (Williams& Starke, 2003). Every designer is striving to find an optimal combination of properties including strength, corrosion resistance and fatigue resistance (Wanget al., 2016). Based on the design principles of aircraft, a higher fatigue resistance of aluminum alloys are required. Thus, many investigations have been carried out on the microstructures and its effect on fatigue properties of the 7xxx series aluminum alloy (Robson, 2004; Schubbe, 2009).Microporosity, which is a common defect in casting materials, can lead to a significant deterioration of mechanical performance and fatigue resistance, especially in the high alloyed 7xxx aluminum alloys. The actual valid loading area decreases due to microporosity, which results in detrimental effect on the mechanical properties. Many experimental studies have been conducted in this research field. Mayer et al.(2003) investigated the fatigue properties of magnesium alloys produced by high-pressure die-casting. The results show that porosity in magnesium alloys greater than0.18mm diameter may be considered as the most important material defect for high cycle fatigue and fully reversed loading conditions. Nadot et al.(2004) found that the near surface defects are much more dangerous than the internal defects. Wang et al.(2001a) used the Weibull statistics method to analysis the influence of the microporosity, oxides and particles on the A356-T6 alloy fatigue life. The results show that, the porosity is more detrimental to fatigue life than oxide films and particles. With regard to fatigue resistance, although the deleterious effect of microporosity has been generally acknowledged, a quantitative understanding between casting microporosity and fatigue life in 7050-T7451 plate is not well established."

Jan 1, 2018

By B. Tiryaki, M. Ayhan, O. Z. Hekimoglu

"This paper discusses the aspects of tracking cutters related to the computer-aided design of shearer drums. A comprehensive computer analysis of drum dynamic parameters for multi-tracking tool arrangement is not presently available, as the current computer programs mainly consider the aspects of single tracking. Despite the fact that the single-tracking arrangement is recommended for efficient cutting, some major drum manufacturers have been seen to persistently adhere to multi-tracking, probably due to a lack of information. Further studies in this field are believed to contribute greatly to the current understanding of the computer-aided design of shearer drums.A number of laboratory simulation trials and long-term underground investigations were carried out in detail on tracking cutter arrangement, and an equation required for a computer program was derived. The results obtained from computer assessment of dynamic parameters for drums with multi-tracking arrangement were found to be in accordance with those of the underground trials, indicating the validity of the equations. The procedure adopted for the computer appraisal of the shearer drums designed with a multi-tracking concept, as described in this study, is therefore recommended to be considered in the currently employed computer programs."

Jan 1, 2003

By Thomas H. Heine

"The Rabbit Lake uranium deposit is located at 58° 11’00”N.. 103°42'36""W., close to the west side of Wollaston Lake, and approximately 800 km north of Saskatoon. The orebody is hosted by Aphebian Wollaston Group rocks, initially deposited as a series of shallow-water marine sediments consisting, in part, of carbonates and possible saliferous petites. Metamorphism during the Hudsonian Orogeny, peaking at about 1850 Ma, recrystallized the sediments to upper amphibolite grade paragneisses. This was accompanied by partial anatexis. The waning stages of Hudsonian orogenesis appear to be marked by minor granitic intrusive activity.The post-Hudsonian period was marked by a long interval of physical and chemical erosion, resulting in the unroofing of the Wollaston metamorphic complex. The entire region underwent extensive lateritic weathering under tropical to subtropical conditions. Carbonates were especially vulnerable and, in the Rabbit Lake area, suffered extensive solutioning with accompanying formation of collapse breccias. Old zones of weakness also underwent periodic reactivation.It was during this period that uranium was leached from the surrounding meta-sediments by oxidizing meteoric waters, and transported into the karsted and fractured rocks of the Rabbit Lake doline.Athabasca Group sediments eventually covered the deposit, their diagenesis taking place at about 200 °C and 900 bars. This allowed the partial to complete recrystallization of the initial mineralization, resulting in a minimum age of 1281 ± 11 Major ""first""-generation pitchblende. Periodic fault/fracture reactivation modified the hydrologic regime within the deposit, resulting in episodic mobilization and recrystallization of pitchblende and other uraniferous species. This is clearly shown in the open pit at the present time: uranium is being mobilized and recrystallized on damp pit walls as bayleyite and liebigite due to the modification of the hydrologic system by mining activities.The uranium mineralization occurs mainly as fracture fillings, coatings, and impregnations within breccia zones and intensely altered metasediments. Lesser mineralization is intimately associated with phyllosilicates which form the matrix of a carbonate-col/apse mega-breccia. The primary ore mineral is pitchblende, consisting of five generations, and from which a large suite of secondary uraniferous minerals have formed. On a gross scale the metal content of this deposit appears to be simple, consisting almost exclusively of U, but minor Ni, As, Cu, Se, Fe and Co are also present. The eastern limit of the mineralization is defined by a vertically-dipping microgranite dyke - breccia complex, containing high-grade uranium values. The orebody is truncated to the west and at depth by the Rabbit Lake reverse fault. Minor mineralization occurs as fracture fillings in unaltered plagioclasite in the footwall of the ore body. Precipitation of uranium from solution could have taken place by a number of processes. A mobile reductant (methane, carbon dioxide, etc.) may have been generated from graphite present in some of the host rocks of the orebody. Sulphides are also a common accessory and may have aided in the formation of a reducing environment. Phyllosilicates may have acted as adsorbants for uranium, allowing for its fixation. This metal has also been incorporated into the phyllosilicates themselves."

Jan 1, 1986

By Harry Wilton-Clark

Introduction Coal cleaning may be taken as meaning the separation of coal-as-mined into two or more fractions. Coal cleaning includes coal washing, together with any other means used in the ultimate preparation of coal prior to shipment (as coal) . The method of coal cleaning devised for any given mine must be one which is based entirely on the economic results obtainable. The installation of a high-cost and complex washing plant, designed to produce a low-ash dean coal, at the highest possible recovery, may be unsound practice. A crude 'roughing' washer may be the best result of sound engineering and operating consideration, and in some cases coal cleaning should be confined entirely to preparation at the face. Consideration of complete costs, to the point where the coal is actually sold, may show that certain seams are workable or not workable. Of the seams found workable, extraction of the whole or parts of the seam may be decided on. The portion to be extracted may contain rock or bone partings, which must be removed. It may be good practice to mine the extra portion and remove the objectionable materials by surface washing; or it may be that such materials should be removed underground, even at an increased mining cost. For instance, in some of the steeply pitching seams of the Alberta Crow's Nest Pass district, the removal of bone and rock at the face may be almost impossible under the usual 'up the pitch' or 'angle' mining methods, but possible by mining across the pitch so that the material to be rejected can be removed and gobbed. Again, if a complete seam is being extracted, investigation may show marked differences between top coal and bench coal, and if sufficient mine cars are being loaded from a chute at one time, the fact that such a place is working top or bench coal at the time may be reflected by peaks in ash content or size proportions at the ripple. It may be very effective coal preparation to smooth out such peaks.

Jan 1, 1934

By John Vergunst

"This paper traces the development of Ontario 's cap lamp standard. Over the years, numerous Coroner's Juries investigating fatal mine accidents have made recommendations with respect to underground lighting. As well, recommendations to improve mine lighting have been made by two Commissions, investigating mine safety in Ontario.During the past few years, the performance of any cap lamp worn by miners involved in serious accidents, have been measured by the Mining Heal/h and Safety Branch. Large variations in light output were found between and among cap lamp types. These variations have been attributed to the lack of quality control on the bulbs, design of the cap lamp head piece and in some cases, poor maintenance.In 1986, a series of underground tests were conducted to establish the minimum light output from cap lamps required to visually identify loose ground. The results of these tests indicated that a cap lamp should produce a minimum peak illuminance of 1500 lux measured at 1.2 metres from the light source. On May 30, 1987, Ontario became the first province in Canada to legislate the minimum amount of light required to visually assess ground conditions. INTRODUCTIONPoor lighting has been identified as a factor which can contribute to mining accidents. Over the past decade, several Coroner's Juries as a result of inquests into mining fatalities, have recommended improved lighting in mines.The Joint Federal-Provincial Inquiry Commission into Safety of Mines and Mining Plants in Ontario, was appointed to report upon the adequacy of existing arrangements and practice s that may affect safety. This Commission completed their report in April 1981, and recommended that inadequate lighting be investigated as a possible cause of all reportable underground accidents, and that a comprehensive research programinto mine lighting be undertaken.In response to the first recommendation, the Mining Health and Safety Branch of the Ministry of Labour, hereafter referred to as the Branch, initiated a program to measure lighting levels in all fatal accident investigations where inadequate lighting was a possible factor."

Jan 1, 1989

By Marc Arpin

La Bolivie possède tout pour réussir. Son vaste territoire de plus d'un million de km2 et qui occupe une position stratégique au coeur du continent sud-américain recèle des ressources naturelles (forêts, minéraux, gaz naturel, etc) variées et abondantes. Elle a une frontière avec pas moins de 5 pays dont le géant que constitue le Brésil ainsi qu'avec l'Argentine, l'autre puissance régionale. Pourtant, malgré tous ces atouts, la Bolivie demeure l'un des pays les plus pauvres du continent. Ce paradoxe n'est nulle part mieux reflété que dans le secteur minier. Celui-ci fait face à une situation de crise en dépit d'une tradition minière de plus de quatre siècles et d'un potentiel géologique indiscutable ayant conduit à la découverte et à l'exploitation de fabuleux gisements d'argent et d'étain. Les habitants des districts miniers vivent dans des conditions de pauvreté extrême et les indicateurs de développement humain de ces régions sont parmi les plus bas en Amérique du Sud. La Bolivie réussit difficilement à attirer les compagnies minières alors que, chez les voisins, et particulièrement en Argentine, qui n'a pas de tradition minière, les investissements miniers majeurs affluent. Dans cette conférence, nous chercherons à expliquer les causes de cette situation et proposerons des solutions possibles.

May 1, 2001

By George Hope, Brigitte Lacouture

"The Red Dog mine has increased mill throughput most years since start-up. Although flotation equipment has been added over the last 10 years, the Red Dog metallurgical performance has been restricted by a lack of adequate flotation capacity. Two reduced tonnage trials conducted in 1997 as well as numerous SAG relines have consistently indicated the potential to significantly increase both zinc concentrate recovery and grade with additional flotation capacity. Later in 1999, a new circuit was designed with increased flotation capacity while simplifying the current circuit, providing for three stages of dilution cleaning, and creating a retreat section. The purpose of the retreat section is to target the more complex particles and allow the chemical environment to be fine tuned for improved iron depression. In total, 21 Outokumpu OK50 (50 m3) mechanical flotation cells and four 3.66 mØ column cells were added to the current flotation circuit. The VIP (value improvement program) mill optimization project is also addressing thickening, water treatment, and power generation issues and has a total budget of US$105 M. Start-up of equipment was phased in to minimize the impact on current operations and the project was completed by the end of 2001. IntroductionRed Dog Operations started production in November 1989. The mine is located above the Arctic Circle in northwest Alaska. It is linked by an 80 km road to a port-site facility where the concentrate is stored. Concentrate is shipped to markets throughout the world during the one hundred days of open seas. As of January 2002, the Red Dog main pit had 38.4 Mt of reserves grading 19.2% Zn, 5.3% Pb, and 102 g/t Ag. Additional reserves and resources contribute an additional 72 Mt at 15.6% Zn, 4.2% Pb, and 78 g/t Ag. Red Dog is a Mississippian to Permian, black shale-hosted, zinc-lead-silver deposit located in the DeLong Mountains, western Brooks Range, Alaska. All the rocks associated with the mineralizing event are considered to be part of the exhalite rock package. Silicification was a dominant component of the mineralizing event and the host shale has been silicified and locally resembles a chert. The major sulphides in decreasing order of abundance are sphalerite, pyrite, marcasite and galena. Most of the deposit’s silver occurs within the crystal structure of the galena. The dominant ore mineral, sphalerite, is very fine grained to amorphous and is commonly intergrown with silica. Ore textures are massive, fragmental, chaotic, veined and rarely show classic sulphide sedimentary layering. The upper portion of the orebody has been physically and chemically weathered. Oxidation has altered the sulphides to sulphates. The zinc and iron sulphates are very soluble and are readily depleted from the weathered cap, while the lead sulphate is residual and is, therefore, enriched."

Jan 1, 2003

By Ernest A. Hodgson

A SERIOUS hazard which must be faced in some mines, though quite absent in others, is that of rockbursts. Bursts cannot be wholly avoided in such mines, but the hazard would largely disappear if they could be predicted. The problem of prediction resolves itself into that of measuring pressure in the mine and determining when that pressure nears a critical value. The geophysical approach to the problem lies in discovering some physical property of the rock, which varies with pressure, which can be measured for rock in place, and for which the indication of critical conditions is sufficiently definite and open scale. A physical property, suggested first in connection with earthquake pre-diction, is that of sub-audible snapping. It was argued that, as the pressure grows, the rock probably yields microscopically and that minute snapping occurs which is so faint as to be inaudible to the unaided ear. Experience has proved this to be the case. Following other earlier work begun early in 1939, experiments with this method were initiated at Lake Shore Mines in 1941, and equipment was slowly being developed in practice when, fortunately, it was found possible to by-pass this tedious development programme. Experiments with sub-audible snapping in mine rocks had been carried out by Dr. L. A. Obert of the U.S. Bureau of Mines and his associates over a period of about four years. An amplifier and a recorder were developed, each reasonably satisfactory in practice. Lake Shore Mines offers a tempting field for rockburst research. Dr. Obert was invited to test his equipment in this and other mines in Ontario and did so. As a result, he and the administrative personnel of the Bureau became interested in the Lake Shore experiments co the extent of most generously arranging for the manufacture of sets of their own designed equipment for use in this programme. The first three sets of recorders were ordered at once and were delivered in May, 1942. A second group of three sets, incorporating various improvements indicated by experience both in the United States and in Canada, reached Kirkland Lake in April, 1943. The pick-up devices, known as geophones, were made in the electronics laboratory at Lake Shore by Mr. Zack Gibbs, who has had charge of all the instrument development in this re-search.

Jan 1, 1943

By J. D. Zhu

A numerical model for predicting microporosity formation in aluminum castings has been developed, which describes the redistribution of hydrogen between solid and liquid phases, the transport of hydrogen in liquid by diffusion and Darcy flow in the mushy zone, One of the key features of the model is that it uses a two-stage approach for porosity prediction, In the first stage, the volume fraction of porosity is calculated based on the reduced pressure, whereas, in the second stage, at fractions solid greater than the liquid encapsulation point, the fraction porosity is calculated based on the volume of liquid trapped within the continuous solid network, which is estimated using a correlation based on the Niyama parameter, The porosity model uses thermal data calculated using the commercial finite element package ABAQUSTM. The model has been applied to examine the evolution of porosity in a series of experimental samples cast using unmodified A356 in which the initial hydrogen content was varied from 0,048 to 0.137 [cc/100g], A comparison between the model predictions and the experimental measurements indicates good agreement in terms of the variation in porosity with distance from the chill and the variation resulting from initial hydrogen content.

Jan 1, 2005

By John L. Hatton

The author will introduce and describe the nature of Fiberglas-Reinforced Plastics. Successful applications of corrosion-resistant structures will be shown and described, including pipe, ducts, tanks and other equipment. These structures are generally designed to handle corrosive liquids and gases and have proved both satisfactory and economical in service in various industries in Canada. The specification of structures will be discussed in relation to materials, construction and workmanship, physical properties and methods of testing.

Jan 1, 1970

By Ellie Condolios

Hydraulic hoisting offers a number ~f attractive features over conventional hoisting methods: small shaft space requirements; great flexibility of layout, including pick-up or delivery of the material at points distant from the mine shaft; low investment and operating costs. However, limited practical experience with this type of hoisting dictates that careful design and, frequently, extensive testing be done by competent engineers before large-scale installations are built. This paper covers the following: basic laws and design criteria for hydraulic hoisting installations; a description of a coal hoisting installation which has been in industrial operation since 1960, with a vertical lift of 600 feet and an annual capacity of 500,000 tons of -3 ~-in. coal; and a tentative appraisal of the process, including cost estimates. THE transportation of solids in water flowing through a pipe-line has, for a number of years, been common practice in dredging, public

Jan 1, 1963

By Anton Gronningsater

AS we know, Sir Henry Bessemer introduced Bessemer converting in the steel industry about 1855. It was not until twenty years later that the principles were adopted by non-ferrous metallurgists. In 1880, Manés first produced blister copper from matte in a converter, a very important forward step in copper metallurgy. For thirty years, up to about 1910, bessemerizing of copper matte was carried out in the acid-lined converter. It is not necessary here to enumerate all the shortcomings of that operation, one of which was that it strictly limited the grade of matte that could be treated; a 35 per cent matte was low in those days. From the early days of copper converting, many and repeated attempts were made to use a basic converter lining, and the older metallurgists will remember the numerous reports and discussions in connection with such experiments. These make interesting reading. I quote from a book published in 1900: ?'The siliceous lining is as much a part of the process of copper converting as magnesia lining is in the basic bessemer treatment of phosphoric iron, and it is suicidal to attempt any other kind of lining, either water-jacketed or basic.' "Even if the silica could be introduced in this way (through the tuyeres), it would still produce another trouble in the converter. The small particles of silica, being cold, would combine very imperfectly with the iron oxide and produce granulated and pasty slags, which could not be skimmed or poured out of the vessel".

Jan 1, 1942

By Laura Steeves, Inoka Eranda Perera, Jhon Silva, Arend Spaeth

"This paper reviews the main concepts ruling the design, implementation and performance of active explosion barrier systems for underground coal mines in the USA. The document examines the parameters needed for the design of this type of system, such as overpressure and flame speed, suppressant deployment speed and duration time of the active barrier. The document also discusses the available solutions for gassy mines and the concepts behind the selection of machined mounted and roadway active explosion barrier systems. The paper includes a review of active explosion barrier systems developed in the USA and South Africa. The paper provides an overview of the current status of this technology in the underground coal mining industry in the USA, and the possible implementation of such systems. The paper concludes with the identification of the future work needed for the successful implementation of the systems in several conditions to enhance the safety of underground coal mine operations and to provide more tools to the miners for their safety.INTRODUCTIONUnderground coal mine explosions can be addressed in two ways, through prevention or mitigation. The United States mining industry practices have emphasized the prevention of explosions in underground coal mines, with little being done to mitigate the explosion once it occurs. Despite successful practices for the prevention of underground coal mine explosions in the US, the threat of an explosion does still exist. Other mining countries around the world have developed and implemented mitigation systems such as active explosion barriers in their underground mines. In the 1970s, the United States Bureau of Mines (USBM) carried out extensive research on the use of active or triggered explosion barrier systems in the US; however, they are not currently used.Explosion barrier systems do not prevent explosions but mitigate the propagation of the shockwave and flame to other areas of the mine. The use of active explosion barrier systems enhance the safety of underground coal mines. Active or triggered explosion barriers will detect the arrival of the shockwave or flame front of the explosion and release inert material to suppress or extinguish the flame. The technology required for active barrier systems is readily available based on their presence in other mining countries and must be adapted for their use in US coal mines. The adaption must consider the coal dust and methane concentrations in US coal mines, the mine geometry, and the mining equipment used."

Jan 1, 2019

By A. Taylor, E. Thorn Corthay, R. Storey

In response to requests from its stakeholders, the International Standards Organisation is engaged in development of an international standard for Energy Management Systems (EnMS) which will become "ISO 50001". This new standard will build on the successes of both the EN16001 EnMS standard that has been used by dozens of European companies, as well as the ANSI/MSE 2000:2008 EnMS standard that is currently being used in several pilot projects in the USA and Ontario. This paper provides an overview of the key points of the EnMS standards, and describes how they can be used to drive sustainable energy reductions in the metallurgy industry.

Jan 1, 2010

By Andrew Kerr

Overview of Presentation ? Introduction ? An historical context: From 1866 to the 21st century. ? Geological framework for iron ore in the region known as the ?Labrador Trough?. ? Producing iron-ore deposits of the Labrador City ? Wabush area, and near-future production from the Schefferville area. ? Exploration projects representing potential future production?.or expansion of the district. ? Some concluding remarks???

May 1, 2011

By A. Ockewitz, A. Trondl, D. -Z. Sun

"Numerical simulation of extrusion processes offers an efficient method for tool design and optimization of geometries and properties of extruded parts. However, until now there are few systematic investigations about influences of material model and different parameters e.g. for friction and thermal processes on calculated local and global responses. Since extrusion processes are essentially influenced by friction between billet and extrusion tools, new friction tests were performed in this work to develop a reliable friction model. Compression and torsion tests were performed at different temperatures and velocities to calibrate the material model for extrusion simulations. Extrusion processes for circular rods and U-profiles were conducted at TU Berlin with backward and forward extrusion for different extrusion ratios, billet temperatures, product velocities and cooling conditions. This work focuses on numerical simulations of the extrusion tests with the FE code HyperXtrude. Based on the calculated distributions of local strain, strain rate and temperature the recrystallized volume fraction and grain sizes were calculated with empirical models and compared with the experimental results from optical micrographs and EBSD scans. The calculated total and friction forces and temperatures were compared with the experimental results and the deviations between experiment and simulation were analyzed.INTRODUCTION Extruded aluminum components are widely used in vehicle constructions due to light weight and manufacturing consideration. Local mechanical properties in the components are inhomogeneous as a consequence of the spatial distribution of microstructure which is influenced by numerous factors like material composition, temperature, tool design, friction, extrusion ratio and speed during the extrusion process. For the optimization of the extrusion process with regard to all these factors numerical simulation can be an essential tool. Based on results of finite element simulations of the extrusion process the microstructure in the extruded components can be predicted and then the resulting mechanical properties can be numerically determined instead of by costly trial and error methods. The aim of the work presented in this paper is the development of a numerical method for the simulation of extrusion processes with modeling of microstructure."

Jan 1, 2018

By B. Meddings, O. J. I. Evans

"This paper is mainly concerned with the present and probable future role of hydrometallurgy in the production of base metals.The economic and technological bases of the hydro-metallurgical plants built and operative in the mid-fifties are compared to those in production in the mid-sixties. The trends observed are extrapolated and some estimates made concerning the probable size and type of hydrometallurgical plants which will be operative in the mid-seventies.The impact of emerging socio-economic factors such as pollution control and the market demand for specialized metal products which favour hydrometallurgical recovery processes are also discussed."

Jan 1, 1971

By D. Karpoff

"IntroductionUNTIL the recent discovery and development of deposits at Allard Lake, on the Lower Romaine river, practically the whole of Quebec's - and indeed of Canada's - production of ilmenite had come from deposits in the vicinity of St. Urbain, Charlevoix •county, a village about eight miles north of Bay St. Paul on the north shore of the St. Lawrence, some sixty miles below the city of Quebec (see Figure l) . Although these deposits were known nearly three hundred years ago and were worked in a small way during the years 1872-74, when a charcoal blast furnace was operated by the Canadian Titanic Iron Company for making white pig iron, it was not until 1908 that more or less continuous production commenced and has •continued to the present by the American Titanic Iron Company. The whole of the output has been exported to the United States.The ilmenite occurs in lenses •and dyke-like bodies within anorthosite. Production has come chiefly from three deposits: General Electric, Furnace, and East and West Coulombe. During 1951 -52, an extensive diamond drilling programme was carded out under the direction of the writer to test the Furnace and the East and West Coulombe deposits (Figures 2 and 3), which form part of the property of St. Lawrence Iron and Titanium Mines, Limited. The average tenor of the orebodies encountered in the course of the drilling was 38.60 per cent TiO2 and, in addition to these high-grade •bodies, there was found a very considerable tonnage of lower grade ore."

Jan 1, 1953

By I. Westermann, K. Marthinsen, M. S. Remøe

"Al-Mg-Si alloys often add small additions of e.g. Mn or Cr, to form dispersoids, which may act as nucleation sites for Mg2Si particles after homogenization. The purpose is to ensure a high density of uniformly distributed small ?’-particles, which can be dissolved during further processing prior to the final age hardening step. However, their density and spatial distribution are critically dependent on the homogenization procedure. It is therefore important to have a robust and reliable method for assessing their spatial distribution. In the present work an existing methodology for assessing spatial uniformity, the Global Shannon Entropy (GSE), has been implemented and evaluated for different dispersoid structures characterized by scanning electron microscopy. This metric is highly dependent on the parameters used, but by careful selection of adequate parameters, it can be effective in detecting non-uniformity. An important weakness with the GSE was identified, and a modification to improve on the ability to differentiate degrees of non-uniformity is suggested. To evaluate the proposed methodology, the effect of heating rate on dispersoid precipitation behaviour during homogenisation of four Al-Mg-Si alloys with different Mn/Cr-content has been investigated. The metric with the new term has demonstrated promising results, and improved the ability to differentiate degrees of spatial uniformity.INTRODUCTION Al-Mg-Si series alloys are the most common aluminium extrusion alloys and are attractive for applications in a range of sectors (e.g. construction, automotive and recently also in consumer electronics), due to their generally good combination of strength, ductility and corrosion resistance. However, their extrudability and end properties depend critically on the alloy chemistry as well as prior processing conditions. Coarse ß-AlFeSi or Mg2Si-particles typically have a detrimental effect on extrudability, while small dispersoid particles may affect recrystallization, grain growth and precipitation of Mg and Si. The strengthening potential in the final age hardening step depends strongly on the amount of Mg and Si in solid solution after extrusion. The manner in which these particles are spatially distributed will decide whether the final product will exhibit uniform properties, and the number density and sizes will determine the extent of the effect. As such, these are important characteristics."

Jan 1, 2018

By D. D. Campbell

The Hat Creek coal deposit s occur within folded and faulted Tertiary (Eocene) strata of the Coldwater Group, which comprises weakly lithified shales, siltstones and conglomerates underlying the floor and lower flanks of the valley of Upper Hat Cr eek . This upland valley,16 miles in length and 2-4 miles in width, is located within the eastern foothills of the Coast Mountains, 120 miles northeast of Vancouver, approximately midway between the towns of Lillooet and Ashcroft, in the Interior Dry Belt of British Columbia . Most of the valley floor is covered by till and glacial outwash deposits ranging up to 500 feet in depth. Became of this overburden cover , the majority of the data on the coal deposit have been obtained from diamond drilling done during 1974?76 by the property owner, B .C. Hydro and Power Authority. Because of the limitations imposed by the lack of out crop, the Tertiary geology at Upper Hat Creek is imperfectly known; however, it appears from correlation with other coal-bearing Tertiary remnants in the southern interior of the province that these remnants, including Upper Hat Creek, may represent preserved segments of the western shoreline of a Tertiary continental sea along which deltaic swamps developed and were sustained for unusually long stable periods, giving rise to the world's thickest known coal beds.

Jan 1, 1977