Search Documents

By Z-Y Pi, B Zhang, S Wen

"The paper introduces the structure and work processes of outside auger hollow claw tipped mechanical sampler for coal. Twenty sets of claw tipped sampler performance tests show that: The design of inner hollow cylinder-type (?180 mm) can ensure to take a coal sample with nominal top size of 60 mm. Built-in self-cleaning piston pusher ensures no adherence and blocking of the sample. The operation practices show that the mechanical sampler can operate in order for taking coal sample with up to 16 per cent of total moisture. Claw closing design can avoid sample leaking or spilling during the claw lifting and ensure the integrity of primary increment. Ultrasonic positioning device makes the sampler capture the materials no less than 10 cm from the bottom of the wagons, basically meeting the requirement taking full depth of the sample. The precision and bias test indicates that the moisture and ash have no relative bias under the sampling process; the sampling precision is in accordance with the requirement in IS013909.At present, the spiral mechanical sampler is widely used for coal sampling but there are many limitations during application, for example: It is difficult to capture a large size sample, so the size range of a coal sample taken is limited. There is easy adhering or blocking for high moisture coal, which will result in the mixture of different increments, wear of sampler and the difficulties for cleaning and maintenance of sampler. It is difficult to capture the coal sample at lower than 30 cm from the bottom of the wagons, in order to avoid damage of the vehicle. It is possible for coal sample loss and spilling during the sampler lifting, due to the unsealed sampler.For the outside auger hollow claw tipped mechanical sampler designed for solving the above problems, the opening distance of the claw is the opening size of the sampler and makes the size range of the coal sample to be taken wide. During sampling, the two pieces of claws open and the sampler rotates vertically downward to capture an adequate coal sample after reaching the specific point. Then the two pieces of claws close tight automatically to ensure there is no coal leaking or spilling. The inner pusher of the sampler will prevent from the adherence and blocking of the coal sample effectively.CITATION:Zhang, B, Pi, Z-Y and Wen, S, 2012. Outside auger hollow claw tipped mechanical sampler for coal, in Proceedings Sampling 2012, pp 41-44 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 21, 2012

By G Balog, T Ormerod, D Sidea

Carrapateena is a copper-gold sub level caving operation located in the Gawler Craton, South Australia. One of Australia’s largest undeveloped copper deposits, the project will be a 4.25 Mtpa underground operation, with an estimated mine life of 20 years (OZ Minerals, 2017). First concentrate production was achieved in December 2019, within the Iron Ore Copper Gold (IOCG) hematite breccia complex. The Carrapateena orebody is overlain by 500 m of barren sediments of the Stuart Shelf, which hosts two aquifers. The cover sequence is dominated by shales, quartzites and sandstones in order of thickness. The cover sequence presented challenges to the mine ventilation system as a result of highly variable rock strengths. On this basis, the site developed the first vent rise, Vent Rise 5 (VR5), earlier than required as a means to test the empirical stability assessment. Assessment for VR5 was completed in 2017, with the mine yet to develop through much of the cover sequence. Due to the geotechnical data available at the time, it was anticipated that break out would occur within the vent rise walls as a function of the low strength Woomera shales. VR5 was developed to 4.5 mᴓ in late 2018. The timing of the VR5 development enabled the site technical team to calibrate empirical stability factors for the assessment of future vent rises. At the time of writing, four additional vent rises have been successfully developed to a diameter of 5.5 m. No significant overbreak has been observed within any of the vent rises. This paper is intended for geotechnical practitioners designing large-diameter vent rises in geological environments similar to the Stuart Shelf where a similar approach to vent rise design may be warranted.

Mar 15, 2021

By C E. Woolley, H Jebaliya, J Foster

The East wall of the Kalgoorlie Consolidated Gold Mines Fimiston Open Pit (KCGM Superpit) has a history of wall instabilities impacting mining operations; the most significant of which occurred in May 2018, when more than 1 Mt of rock dislodged over six, 30 m high bench stacks and impacted the pit floor. Since 2011 approximately 1.250 Mt of material has fallen from the East wall at Fimiston Pit across three failure events (2011, 2018 and 2020). Each failure has been associated with major structures intersecting the pit walls: the Fiji Fault, the Australia East Secondary Splay Fault and the EWD3 Fault. In each instance the trigger for failure has been transient pore pressure in the pit walls. Northern Star will mine a cut back behind the failure area over a vertical distance of 180 m. Cut back mining will include the extraction of a remaining in situ wedge, which is assessed as kinematically able to fail, and a subvertical failure backscarp in Stage 1. A substantial amount of rill material from the 2018 and 2020 failures will be extracted in Stage 2. This paper presents the methodology in use to mine Stage 1 of the cut back, safely, through this potentially high-risk area, detailing the specific mining methodology employed, the controls put in place and the monitoring required. Day-to-day monitoring will be undertaken using the already installed slope stability radar and will feed into a daily assessment of activities which may be undertaken in the cut back area. Initial activities will focus on eliminating the potentially unstable wedge and vertical backscarp with use of innovative drill and blast techniques/products and the extensive use of remote capable equipment to limit personnel exposure.

Jun 22, 2022

By S Henderson

The Otago Goldfield has produced approximately 8 million ounces of alluvial gold and over 2.5 million ounces of hard rock gold and is currently home to New ZealandÆs largest producing gold mine. In the eyes of explorers this production history makes the goldfield a good place to explore.   Modern exploration in the Otago Goldfield commenced in the late 1970s with the exploration for tungsten. However, a rapid rise of the gold price in the early 1980s saw the focus shift to the exploration for gold which lead to the discovery of the Macraes Gold Project in 1984, which since it came into production in 1990 has been New ZealandÆs largest producing gold mine. With the exception of the Macraes Gold Project, exploration continued in the Otago Goldfield for a further 20 years without further success.   In 2006, Glass Earth (NZ) Limited (Glass Earth) reviewed all the exploration technologies applied to the Otago region and available geological data, including the 1996 OceanaGold Helicopter Electro-Magnetic (HEM) data, and concluded that combined magnetics and HEM were able to delineate the Hyde Macraes Shear Zone (HMSZ) which hosts the Macraes Gold Project. Unlike previous explorers who explored the Otago region in a piecemeal manner, Glass Earth opted to collect a new, region-wide dataset which could be integrated with all previous collected geological information to come up with new exploration concepts and targets. As part of this process, Glass Earth applied in mid 2006 for New ZealandÆs largest on-shore gold Prospecting Permit, PP39-322 which was subsequently granted in November 2006. In mid January 2007, Glass Earth commenced acquisition of approximately 50 000 line kilometres of HEM data, making the Otago regional aerial geophysical survey (survey) the largest aerial geophysical survey ever undertaken in New Zealand.   This paper will report on the progress of the Otago Regional aerial geophysical survey and outline some of the preliminary findings from what is still a work in progress.

Jan 1, 2007

By L Xiong, W J Shi, J H. Wei

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Baizhangzi gold deposit is located in the northern North China Craton. The structural and lithological controls on the location and geometry of orebodies were studied through geologic survey, ore spatial configuration analysis and structural analysis. The orebodies of the deposit comprise auriferous quartz-sulfide veins and disseminated gold-bearing sulfides. The auriferous quartz-sulfide veins are dominantly hosted by the NNE- (and NE- and NW-) trending faults, which are subsidiary structures of the regional NNE-trending F2 fault. The subsidiary NNE-trending faults, having sinistral reverse kinematics, are associated with the sinistral reverse kinematics event of the F2 fault, which happened under a regional S–N-oriented compression stress field. The subsidiary NE- and NW-trending faults appear to be compressive and extensional respectively. These NE- (and NW-) trending faults are restricted to the granite intrusion and are associated with a sinistral strike-slip event of the F2 fault, which reactivated under a NW–SE-oriented compression stress field. It makes significant influence on geological evolution and distribution of different ore types that the strike of the F2 fault presents significant transition from NNE- to NE-trending in vertical. The ore-bearing disseminated host rocks, with widespread silicification and pyritisation, distribute in the lower inner contact zone of the granite intrusion, especially in the lower wavelike boundary of granite intrusion.CITATION:Xiong, L, Wei, J H and Shi, W J, 2015. Structural and lithological controls on the location of orebodies in the Baizhangzi lode gold deposit in western Liaoning Province, China, in Proceedings PACRIM 2015 Congress, pp 193–200 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By S Jeffrey, S Mundell, F Arboleda

In the current cycle of low commodity prices and rising costs, mine managers continue to focus on optimising mine performance and productivity. A critical component of strengthening performance and productivity is ensuring material is routed correctly and efficiently through the core mine production activities of drilling, blasting and grade control.By the time a blast is planned, an enormous amount of intellectual property has been invested in the exploration, resource development, feasibility studies and mine planning activities. The value of that knowledge is either realised or diminished during mine production. Efficient execution of the process is critical and is reflected by the quality and timeliness of the information produced.Multiple teams are involved in the mining extraction process. These teams are all under time pressure to keep the mine equipment operating. One of the root causes of this pressure is the dependency between the teams. They do not operate in isolation, but are a link in a chain depending on the outcomes of each activity. It is essential communication is efficient so tasks can be completed according to the production schedule. Unfortunately, communication fails when unintegrated systems are used because of:- different teams seeing different data, hence there is not an overall, up-to-date view of progress and priorities- lack of cross-functional visibility of data leading to failure to identify errors in time to address or correct issues- teams tending to be siloed and focusing on their part of the process rather than the overall objective.With different systems used for the parts of a common goal, supervisors and managers lack visibility of the process. This makes it difficult to identify process improvement opportunities.Streamlined communications help consolidate all data and activities resulting in improved cooperation between mine production teams. This outcome increases the confidence and efficiency of material routing decisions. It also reduces potential impact to mine performance from errors in early stage tasks like drilling and grade control. Having everyone collaborating off the same trusted data, helps teams identify with common goals and find business improvement opportunities as they appear.CITATION:Arboleda, F, Mundell, S and Jeffrey, S, 2016. Driving mine performance through communication, in Proceedings International Mine Management Conference, pp 117-124 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

TSL Concepts and Practical Examples of the Non-Reactive System - Meyco TSL 865 Thin Spray-on Liners (TSLs) have been intensively investigated by mining and chemical industries within the last decade. Apart from the basic concept of spraying thin liners, expectations of the product's performance vary, eg immediate active strata support is seen as a key to control the ground permanently. For many coal mines this is an important factor to reduce maintenance in their roadways and enable permanent production from the long wall. In opposition to a passive mesh system this technology offers immediate active support to the strata. But not only coal mines are interested in TSL technology, there are potential applications in hard rock mines, during shaft sinking, pillar support and as an anti-weathering sealant. This paper will explain the advantages and disadvantages of TSL concepts; it will give examples of successfully applied TSLs with a main focus on the non-reactive and flexible system MEYCO TSL 865 by BASF. Furthermore, it will indicate the limitations and discuss briefly the bearing capacity and reasonable lab testing of such systems.

Nov 25, 2010

By M A. Llano-Serna, D J. Williams, L Bu

Tailings dam failures continue to occur worldwide at an unacceptable rate, averaging two events annually over the last 100 years. Furthermore, tailings dams continue to grow in size, increasing the potential release of tailings and water should they fail. Tailings are generally deposited in a slurry state, with the potential to flow if containment is lost. Understanding the generation and propagation of excess pore water pressure on failure is critical to predicting the flow and run-out of tailings. This paper presents numerical modelling using the material point method indicating that tailings run-out processes may be self-enhanced by the excess pore water pressure induced during the collapse of the containment. Moreover, it is shown that geomorphological features, such as the slope and its surface roughness downstream of the tailings dam, influence the pore water pressure dynamics upstream of the advancing toe.CITATION:Llano-Serna, M A, Bu, L and Williams, D J, 2018. Excess pore water pressure induced during tailings run-out, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 377–383 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By F Wu, H Wang, W Chen

A pressurisation method with multiparallel fans has been adopted at HongLiuLin Coalmine to control the significant external air leakage through the goaf area of coalface 15207. Potential damaging effects of large external air leakage on a coalmine’s ventilation system are analysed according to the current air leakage status caused by the exploitation of shallow-covered coal seams. The use of pressure balanced ventilation to prevent external air leakage through goaf areas is introduced. The calculation of ventilation network of HongLiuLin Coalmine shows that the air resistance of an external air leakage branch through a goaf area and the air pressure drops from the intake slope to the working face can be adopted to determine the values of pressure to be increased by regulating fans and airflow controlling parameters of regulators. By investigating airflow requirements of the pressure-balanced area as well as the performances of the auxiliary fans currently used in the coalmine, the number of pressurisation fans needed is fixed. The expected result is achieved after the pressurisation method has been carried out, which can be helpful for other coalmines to handle similar problems.CITATION:Wu, F, Chen, W and Wang, H, 2015. Multiparallel fan method to prevent significant external air leakages through a goaf area of a shallow covered coalmine, in Proceedings The Australian Mine Ventilation Conference, pp 267–270 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By A Sadri, S Smith

In the metal and mineral industry, different empirical techniques are used to estimate the remaining thickness of the lining within an operating furnace. The disadvantage and costly factor when using these methods is that production needs to be halted. Hatch has developed an accurate and reliable technique based on stress wave propagation principles to determine the condition of the remaining lining whilst the furnace remains online and operational.The technique involves test data collected and compiled to generate 3D imagery used to assist operators and maintenance planning personnel with valuable information showing areas of metal penetration in the lining, remaining lining thickness, exact location of voids, cracks, poor contacts and deterioration due to chemical attack. In this paper, the principals of the AU-E technique will be explained both theoretically and practically. In addition, the use of ultrasound technology for determining the condition of copper cooling elements will be briefly addressed.

Jan 1, 2006

By G Noonan, S Thomas, M Limbert

Stuck drill rods (often referred to as bogged rods) in production ‘upholes’ are a common problem in the underground mining industry. Bogged and broken off drill rods have the potential to fall out of the hole without warning, posing a serious hazard to personnel and equipment below.Current industry practice to alleviate this hazard can be to either grout the hole in order to lock the drill rods in place, or to ‘plate over’ the hole with a rock bolt. Each of these operations seriously delays mine production as both require demobilisation of the production drill and mobilisation of alternative personnel and equipment to address the hazard. Both methods have been assessed for safety and efficiency and were found to be expensive, time consuming and in the case of plating over, ineffective.To address the safety and efficiency short-comings of the traditional practices, the long hole plug (LHP) has been developed to safely secure the lost rods in the hole. The LHP when struck by falling drill rods behaves similar to an expansion shell anchor transferring the axial forces from the falling drill rods horizontally into the rock mass. It is installed using standard production drills allowing work to safely continue with little interruption.Extensive testing has been carried out on the LHP in the laboratory and underground at the Rosebery mine on the west coast of Tasmania, Australia. Testing has included static pull testing, full scale drop testing and underground trials.The outcome of this work has proven the LHPs ability to add safety, volume and cost benefits to the Rosebery underground operation and it is currently in use at that site. It enables proven elimination of a common workplace hazard immediately, thus eliminating delay on the mine’s production cycle.CITATION:Thomas, S, Noonan, G and Limbert, M, 2017. Long hole plug – addressing the hazard of bogged rods in ‘upholes’, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 305–310 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By C E. Woolley, A Hosseini, J Foster

Northern Star’s Thunderbox Open Pit C-Zone cutback was designed to maximise extraction in a short life excavation; In fresh rock on the western wall this included 20 m to 30 m bench heights with 6.5 m to 10 m berm widths and a 90° pre-split angle. Rock mass quality in this area is generally fair to good, however, there are sections where the dominant foliation runs parallel with the designed pit wall, and more closely spaced, altered, foliation is present: these areas are difficult to predict and prone to failure. Stringent controls and monitoring were required in order to safely access below these areas, in particular the use of slope stability monitoring radar, Trigger Action Response Plans (TARPs), re-entry procedures, visual inspections, drone inspections and day-to-day personnel awareness of the hazard. Robust and comprehensively planned remediation was also required after two significant slope failure events where long reach equipment and rope access techniques were utilised to remediate the areas in question safely, but also in a timely manner, such that expected production targets were impacted as little as reasonably practicable. This combination of rigorous risk management and well planned remediation resulted in a successful and complete extraction of the C-Zone cutback with no impact to operational safety.

Jun 22, 2022

By P Viljoen, A Holland, C Parken

In the raisebore industry, there are two known methods of removing large diameter reamer heads once the reaming of an underground shaft is complete: 1. Lower the reamer head to the base of the shaft and use a thermal lance to cut the drill string and drag the reamer away from the hole. This method exposes the person doing the job to falling rocks from the unsupported mineshaft, a hazard which is difficult to control and has caused fatalities. 2. Install breast plates in the backs above the reamer head at the top of the hole, and use air hoists to lift the reamer out of the hole. Steel beams are then placed across the hole which the reamer is lowered down onto, dragged forward away from the hole, disassembled, and removed. This method is time consuming, expensive, and complex in the controls required to ensure safe completion of the job At Carrapateena, the air hoist method had been successfully used, however, with the cost involved and the complexity of this process, development of an improved and fit for purpose reamer removal method was pursued. OZ Minerals collaborated with Pybar to develop an industry first application of Enerpac SL100 lift and shift technology; a track mounted system with hydraulic lifting units that can both lift the reamer out of the hole and tram it back along the tracks away from the hole. A key component of turning the idea into a reality was by establishing a truly collaborative relationship between client and contractor. When the SL100 mobile gantry arrived, it was set up in Adelaide and trialled with the whole raise bore crew attending the two-day workshop and risk assessment; a rare opportunity for drillers. There have now been five successful reamer removals with the SL100 mobile gantry at Carrapateena. It has proven to be an efficient process with the entire process from setup to demobilisation taking less than 48 hours. This new way has completely removed hot works and uncontrolled hazards from working at the bottom of a shaft. It has also saved the reamer stabiliser from being cut and thus wasted. Exposure to the open hole has been minimised significantly as assembly of the SL100 is completed well forward of the open hole. This new process is exponentially safer, quicker and cheaper.

Mar 15, 2021

By S Maritsa, D Simbi, E K. Chiwandika, S M. Masuka

The steel industry is facing challenges on a global scale that include depletion of resources, huge energy consumption, and the emission of CO2. The demand for iron products is increasing due to the increased infrastructural development. Zimbabwe produced cast iron from scrap metals. However, there is currently a shortage of scrap, and yet Zimbabwe is rich in limonite ores that are currently being underutilised. The possibility of using limonite ore as a sustainable feed for pig iron production was investigated by preparing some limonite ore carbon composite pellets. The results showed that the addition of coal to the limonite ore and calcium carbonate mix to form the composite pellets resulted in a decrease in the drop number as well as the dry compressive strength of the composite pellets. This research aims to improve the physical properties of the green pellets by the careful addition of hydroxyethyl cellulose as a binder that was found to improve the physical properties of the green pellet. This is important for materials handling during the production process of the composite pellets. Results showed that the drop number was substantially improved by the addition of 0.4 wt per cent hydroxyethyl cellulose while the dry compression strength improved from 2.5 kg/pelIet to around 23 kg/pellet irrespective of the amount of binder added. The binder improved the physical strength of the iron-carbon composite pellets enough to allow for large-scale production of the pellets that can be an alternative and sustainable feed for cast iron production. However more results on the indurated compression strength and other properties such as the reduction degradation index, swelling index, and the reducibility test are required.

Jun 19, 2024

By A K. B Chigwada

Mining organisations grapple with the same problems year after year, wasting incredible amounts of time and money. According to estimates from the International Labour Organization (ILO), over one million work-related deaths occur annually, and hundreds of millions of workers suffer from workplace accidents and occupational exposure to hazardous substances worldwide. Many accident reports cite human failure as a primary cause (Busse and Johnson, 1998). The workers at the Bhopal chemical plant pumped methyl isocyanate into a leaking tank (Morehouse and Subramaniam, 1986). On 3 December 1984, more than 40 tons of methyl isocyanate gas leaked from a pesticide plant in Bhopal, India, immediately killing at least 3800 people and causing significant morbidity and premature death for many thousands more. The company involved in what became the worst industrial accident in history immediately tried to dissociate itself from legal responsibility (Broughton, 2005). Australia is not spared from safety problems either (Lucas, 2022). The ILO Convention 176 (1995) as a response provides that national law should inter alia provide for the supervision of safety and health in mines; the inspection of mines by designated inspectors of the competent authority; the procedures for reporting and investigating of fatal and serious accidents; the compilation and publication of statistics on accidents, occupational diseases and dangerous occurrences; the competent authority to suspend or restrict mining activities on safety and health grounds until conditions giving rise to the suspension are addressed; and worker consultation on matters related to safety and health in mines. This has assisted in getting enough data to define the magnitude of the problem to the mining sector.

Apr 16, 2024

By M Davis

Increasing growth in the minerals industry over the past decade has raised the question of whether the standard of training for new geologists has been negatively impacted. This hypothesis was tested by means of a survey. Factors considered included the quality of training and whether it has changed over the past 50 years, preferred styles of training compared to styles of training received and whether the quality of training provided by a company changed with the type or size of company. Data from 435 survey respondents showed a consistent standard of training, but a significant increase in the level of responsibility allocated to new geologists. Those with increased responsibility also had reduced access to additional support and were often asked to perform tasks for which they had little or no training. New geologists were more likely to receive better quality training in a large company (over 100 employees) that owned the mine or exploration lease. A more structured training program was more likely to provide a higher quality result than those with minimal or no structure.

Aug 22, 2011

By D Kay, M Lovitt

Mass Blasts are generally required at the completion of longhole stoping cycles to maximise the recovery of ore from a specific orebody. During the course of mining, the practice is to leave pillars of ore to support the opening left by extracted ore and to mitigate stresses from working areas of the stope. These pillars usually contain ore that has been included in the resource evaluation and is highly valuable to the mining operation. Due to their stressed nature, the removal of pillars by conventional blasting techniques, through small blasts, can result in pillars being reduced beyond their critical size and ultimately failing, rendering the ore unrecoverable. The AurionGold Kanowna Belle Gold Mine operates a Mine to Mill philosophy. This philosopy requires the fine tuning of blasting to provide the best possibe ore feed at the highest grade for mill productivity. This means that ore to the mill must be well fragmented from blasting that provides high extraction rates from draw points, with minimal dilution from overbreak or fall off, and sized to maximise SAG mill throughput. The AT04 Mass Blast contained significant ore reserves which were required to meet gold production targets. KBGB needed the AT04 Mass Blast to perform as well as if not better than conventional stope blasts to maintain mill production. This paper describes the circumstances, planning philosophy, techniques, including the use of Electronic Initiation Systems and Bulk Emulsion Explosives, and results that provided a highly successful outcome.

Jan 1, 2002

By R McCarthy, P Darvall

FerrAus Limited's Robertson Range and Davidson Creek iron ore projects are located on the far eastern margin of the Hamersley Province, approximately 100 km to the east of Newman, Western Australia. The deposits are primarily formed of bedded haematite-goethite-limonite mineralisation within the Marra Mamba Formation, comprising a total combined resource of 164 Mt at 58.6 per cent Fe. The deposits represent relatively new discoveries for the Hamersley Province. The potential for mineralisation at Robertson Range was identified by Rio Tinto Exploration in 2000, while Davidson Creek remained untested until 2007. One of the main reasons for this is that these deposits are almost exclusively concealed beneath Tertiary sediments and recent transported cover making them difficult targets for conventional, prospecting style exploration. Since commencing exploration in the project area, FerrAus has collected nearly 20 000 stations of gravity data within the Robertson Range and Davidson Creek project areas, with most of this data collected at a 50 100 m station spacing. Gravity has proven itself to be an effective technique at predicting the position of the target host stratigraphy and has been a key driver in the exploration for concealed iron ore deposits. However, there is not always a perfect correlation between the position of gravity anomalies and concealed ore. The response of deep haematite bodies may be masked by low-density cover rocks, while other dense lithologies may be the cause of gravity anomalies which appear similar to the Marra Mamba targets. Hence, effective use of the gravity data requires interpretation in a geologic context with an understanding of the capabilities and limitations of the technique.

Jan 1, 2009

Blasthole cone samples are used for grade control in most of the iron ore mines of the Pilbara of Western Australia. This method of sampling is straightforward when the target sampling interval matches the mining bench height but is problematic when the blasted bench is 'flitch' mined in two or more passes. Crucially, the sampler needs to decide which part of the blast cone represents the upper and lower flitches to be mined. This sampling selection decision is usually made by assuming a certain proportion represents the subdrill component of a sampling face in a blasthole cone and the two flitches are split equally from the remaining portion. In this study of a West Australian channel iron deposit, sampling experiments were carried out to determine the actual proportions of a sampling face in a blasthole cone by spray painting the blast cones at flitch and subdrill boundaries during the drilling process. Measurements were then taken to assess the differences between assumed sampling face proportions and actual proportions. A set of paired samples was also collected from a number of blastholes with one set using the assumed proportions of each flitch for each sample, while the other set sampled the actual proportions, which were identified from the cone painting process.

Mar 1, 2010

By J Sargeant, T Levi, J Theiler, B Beamish

Two coal samples (810 Panel and Area 900) collected from Clarence Colliery have been tested under a controlled heating procedure to evaluate the gas evolution trends corresponding to increasing temperature. Gas evolution data are normally used to identify key gas indicators and validate the trigger action response plan settings for the mine as part of the Principal Hazard Management Plan for Spontaneous Combustion. The samples were located some 6 km apart and there is a significant coal-type difference between them. At low temperatures (<100°C), the Graham’s ratio (GR) values for the two samples are almost identical. However, at elevated temperatures, there is a significant difference, with the 810 Panel coal having higher GR values than the Area 900 coal. This is most likely due to a difference in the coal reactivity. The 810 Panel coal does not evolve ethylene until temperatures in excess of 140°C are reached, whereas Area 900 coal evolves ethylene once temperatures in excess of 120°C are reached. The 810 Panel coal also produces significant ethane evolution (200 ppm) at low temperatures (50°C) due to the presence of retained ethane seam gas, which decreases as the temperature increases due to desorption from the coal. Once the coal temperature exceeds 130°C, the ethane evolution increases again due to coal oxidation reactions, reaching levels of 50 ppm. In contrast, the Area 900 coal has no significant low-temperature ethane evolution, and ethane evolution only increases once the coal temperature exceeds 120°C. There are also noticeable differences in the trends of other gases evolved from the coal. These findings have implications for the interpretation of gas monitoring results from the two different areas of the mine. They also illustrate the need for obtaining results from each new area of a mine as it develops so that changing gas evolution trends can be identified in advance of mining.CITATION:Beamish, B, Sargeant, J, Levi, T and Theiler, J, 2015. Gas evolution trends for coal from two different areas at Clarence Colliery, in Proceedings The Australian Mine Ventilation Conference, pp 273–278 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015