Search Documents

The authors have succeeded in providing additional rigour and clarity to the formulation and execution of the dynamic programming algorithm for optimum open pit limit determination. The inclusion of the blocks on the J + 1 column in the search for Pmax, and constraining this search with blocks assigned a value of negative infinity, ensures an optimal solution within the defmed blocks. The effect of the negative infmity blocks is to preclude mining along the diagonal blocks from the first row that they occur in. Figure 1 graphically illustrates the effects of this on the calculation of P. A practical application for constraining mining with negative infmity blocks is the case where the pit outline is defined by lease boundaries and not by the value of blocks to be removed. Any legal, social or physical constraint could be accounted for in the same way.The danger in applying this technique is that the negative infinity blocks will override any other more profitable solutions that may exist. This is in fact what has happened in the example that the authors use. If a further column is added to the left hand side (column -1) and the calculation is carried out again, a more optimal x-section can be found. (If the negative infinity values are removed the same result is obtained.) This gives a pit value of 112 as against the 108 of the authors' optimal pit. This calculation is shown in Figure 2. Lerchs-Grossman optimization is reliable only if there are sufficient columns available to allow "mining" to optimum depth of the ore body and still allow the pit to break out at the surface within the confines of the columns.This author's approach is to create enough columns each side of the lateral limits of the ore to allow the pit to intersect the surface while still within the confines of the block model. Implementing the methods discussed by the authors helps to reduce the number of columns required to achieve this.

Jan 1, 1987

By D Thornton

Geologists use large data sets and spend many hours and much computing time modelling the distribution of minerals throughout a rock mass. Significant investments in drilling, assaying and quality assurance and quality control (QA/QC) are made before sophisticated geostatistical techniques are applied to the collected data. A large amount of research has been done in this field such that the ore control model is a reasonably accurate reflection of the mineral that is actually in the ground. However, after all this effort, the mining engineers then work just as diligently to blast the in situ rock mass to a particle size that can be efficiently handled and further reduced by downstream comminution processes. In open cut mines, this invariably requires large amounts of explosive energy that displaces the ore boundaries from where the geologists originally defined them. Failure to accurately account for blast movement will result in misclassification, whether that is ore to waste; low grade to high grade; sulfide to oxide; or other contaminates û collectively referred to as ore loss and dilution. The financial consequence of getting this wrong is substantial and not well quantified. This diminishes all of the good geological QA/QC done in defining the ore. This paper discusses various technologies used to physically measure blast-induced orebody movement and the difficulties in modelling this with a purely theoretical approach. Rock mass structure, blast energy, design and timing contours all have significant and interrelated effects on blast movement vectors. Measured blast movement has a large variance due to the uncertainly of many of the controlling parameters û arguably dominated by the heterogeneous nature of the rock mass. Although there have been significant advances in blast movement modelling capability in recent years, this unpredictable blast movement limits their use in the context of production ore control. Certainly, without physical field measurements, accurate predictions of movement are near impossible.Limitations of traditional surface markers in determining three-dimensional (3D) blast movement within the orebody are also reviewed, and advancements in accurately measuring these vectors within blasted ore discussed

Sep 26, 2011

By Fredley D. C

Georgius Agricola wrote in De Re Metallica in 1556 that a prudent a miner should not work in a region ruled by a tyrant-a person inimical to mining. In 1926, Associate Chief Sherman of the United States Forest Service in a speech stated, "It is the policy of the Forest Service to encourage the development of the mineral resources within the boundaries of the National Forests ... a man who fails to cultivate a friendly, helpful, cooperative spirit in his relations with those who are endeavoring to develop the mineral wealth of our mountains has no place in the Forest Service." Both statements are as true today as they were in 1556 and 1926. The challenge to the Forest Service and the mineral industry today is to maintain that cooperation in a world that has changed significantly since Agricola and Sherman. The United States Forest Service manages 77,000,000 hectares of land-mostly in the Western United States-an area equal in size to New South Wales. The vast majority-75 million hectares are National Forests, and 1.6 million hectares are National Grasslands. National Wilderness Areas account for 13 million hectares or rough- ly 17 per cent of the National Forest System. National Forest System lands (NFS) are some of the most visible, scenic and controversial lands in the country. They are also some of the most valuable for their mineral potential and production. The value of mineral produced exceeds US$4 billion per year. There are over 1200 producing mines, 15,000 oil and gas leases, and some of the largest lead, copper, silver, gold, platinum, molyb- denum, and coal deposits in the hemisphere. Every year the Forest Service approves nearly 5,000 mineral operations on the NFS. Much of the NFS (75 per cent) is open to location of mining claims pursuant to the 1872 Mining Law. And an equal amount of land is legally available for oil and gas leasing.

Jan 1, 1991

The control system of a mine winder or other variable speed drive has many component parts that must work together to provide the required functional performance of the machine, together with comprehensive safety features, reliability, maintainability, user-friendliness and efficiency. Modern winders use digital control technology extensively and hence software design is a major part of the overall system. It is not practical to simulate an entire mine winder in a single computer model because of the sheer mathematical complexity of the behaviour of many of the components. However, most component parts can be simulated quite easily, and related parts of the control system software can be simulated. Such simulations allow control software algorithms to be developed and tested in isolation from the real plant. Tests can be performed on the model without fear of injury to personnel or damage to the valuable plant. For example, speed regulator control algorithms and stability settings can be adjusted to and beyond the limits of stable operation, and near optimum settings can be found. This is particularly important, for example, when designing closed loop controls for emergency brake systems. Obviously, care must be taken to ensure that the computer model of the plant is realistic and takes into account as many non-linear features of the real plant as possible. Pure mathematical analysis of some systems is very difficult to perform when non-linear plant behaviour is involved. This paper shares a number of practical simulation experiences performed using commercially available software such as Matlab and Simulink to simulate various parts of the control system of a mine winder or other variable speed drive. Demonstrations of the operation of several different computer models are shown during the presentation of the paper.

Jan 1, 2005

This paper considers three aspects of cemented fill practice and research in Mount Isa. Firstly, an account is given of the use of Portland cemented hydraulic fill both in MICAF sills and in recovery of major horizontal pillars in the 650 copper orebody, where, during mining, cemented fill has regularly been exposed on unsupported vertical faces up to 90 ft high. In the paper the main considerations are the role and specifications of the fill used but also included is a brief description of fill preparation and placement.Data resulting from a Portland cemented hydraulic fill sampling, curing and testing campaign covering about 18 months of operating practice are presented, analysed, and discussed. These yield information indicating the mode of operation of a fully-automated fill preparation station, as well as a means of comparing field and laboratory strength results. A technique with potential for use as a fill quality control without actual strength testing is also described. The data collected showed that the fill station can operate within tolerances set on product quality, that laboratory and field strength results are comparable, and that rapidly obtained fillsample properties such as moisture content and void ratio can be related to cement content and strength, and hence used for quality control.Results of a fill research programme conducted by the author in Mount Isa since early 1968 are presented involving Portland cemented hydraulic fill and alternative, cheaper additives for cementing hydraulic fill. The most significant alternative to Portland cement is quenched and ground copper reverberatory furnace slag, whIch behaves as a pozzolan, reacting strongly with any available lime to produce cementitious hydrated calcium silicates and allowing Portland cement reductions of at least 50 per cent without strength loss.

Jan 1, 1971

By P Commander

Western Australia is a major exporter of minerals, which places significant economic and environmental responsibility on Government and the stateÆs mining industry. Moving into the 21st century, mineral production in Western Australia is $14 billion accounting for 50 per cent of the stateÆs export income. There are over 60 large-scale mining operations distributed throughout the arid regions of the state (less than 300 mm/year rainfall). There are four key mineral provinces in arid Western Australia including the Pilbara (iron ore), Murchison (gold), Northern and Southern Goldfields (gold and nickel). These provinces have significant differences, particularly in respect to groundwater demand from mining and mineral processing, aquifer systems that are utilised, and approaches to groundwater management. The arid nature of the stateÆs interior and subsequent lack of surface water resources has required substantial groundwater resource development by the mining industry. A variety of aquifers have been explored and utilised ranging from shallow alluvium and calcrete, discrete fractured zones in bedrock, concealed palaeochannels and inland sedimentary basins. Groundwater usage by the mining industry is about 150 GL/year with most abstraction related to mine dewatering, mineral processing and dust suppression. Groundwater abstraction in Western Australia is regulated by the Water and Rivers Commission. In the Goldfields, the depletion of brackish (>2000 mg/L) and saline groundwater from storage is permissible, as mining is considered the beneficial use for groundwater which may be as much as 200 000 mg/L. In contrast, the low salinity groundwater of the Murchison and Pilbara is allocated on a sustainable basis. The role of monitoring and ongoing aquifer reassessment is crucial in water management, in evaluating the condition and performance of stressed aquifer systems. Mining operations face a variety of water resource issues ranging from insufficient availability for processing to excessive mine dewatering. These issues also change as a mine operation proceeds through its development, commonly starting with a deficiency and moving into surplus as deeper pits require more dewatering. Operating mines have to contend with three main issues: water supply, wastewater disposal and contamination of local water resources. In contrast, post closure issues are related to aquifer recovery or re-establishment of groundwater equilibrium, development of pit lakes in mine voids and isolation of waste products and associated seepage or run-off.

Jan 1, 2003

By P Gnnther, A M. van Niekerk

Coal mining operations in the Upper Olifants River Catchment in the Mpumalanga Province of South Africa are challenged with the increasing production of excess mine water that cannot be fully managed by existing practices of pollution control at source, recycling, and reuse on mining sites, storage and limited release to the natural water course. In contrast to this, the Olifants River Catchment is experiencing water stress and insufficient water is available to satisfy all water quantity and quality requirements for future industrial and municipal growth. It is estimated that the catchment has a deficit of 192 million m3 per annum if the reserve water requirements are taken into account. The future increased water requirements can be met by water transferred to the Olifants River Catchment from adjacent catchments. The cost of transferred water is likely to be substantially higher than the current cost of water supplied to local municipalities, commerce and industry. BHP Billiton and Anglo Coal Corporation are working together to jointly implement water management strategies that will contribute to the achievement of in-stream and dam water quality and aquatic objectives for the catchment. Consideration is now being given to the treatment and beneficial use of excess mine water. This will inaugurate a new era for the coal mining industry in South Africa, in which a pollution threat to the water resources in the Upper Olifants River Catchment is converted into a water source for beneficial use. Three potential mine water reclamation and reuse schemes have been identified and this paper details the technical, institutional, legal and financial considerations in the implementation of these schemes.

Jan 1, 2006

The paper poses certain questions relating to mine design aspects of deep shaft pillars. It then explores these questions in relation to Western Deep Levels (South) where a sub-shaft system is to be sunk to 4 000 metres below surface to exploit two narrow tabular reefs in the down dip extension of the mine workings. After brief discussion of some broad considerations, the findings of a major rock mechanics investigation are reviewed. Some overall conclusions as well as the outcomes of separate studies of the anticipated behaviour of shaft pillars on each of the two reef horizons are outlined. The effect of this behaviour on the barrels of the shafts in the system and on the associated shaft excavations and in-pillar development is Cnnctdarcrl

Jan 1, 1986

By Sharpin PC

The countercurrent gas-solid-heat transfer during the drying of brown coal briquettes in the pilot carbonization plant at Morwell has been analysed and theoretical gas and solid temp-erature distributions through the drier have been calculated. Although the calculations rest on several simplifying assump-tions, to be corrected as the experimental work develops, the theoretical temperature distributions compare well with those observed in practical operation. Valuable conclusions are reached as to the effects of changes in drier operating con-ditions on the rate of drying of the briquettes which-controls the 2 strength of the char produced. The analysis shows why a limitation was reached in the improvement of char-strength in the pilot plant in 1961 and a prediction is made of ' a way ' in ' which the limitation could be overcome.

Jan 1, 1963

Strip mining offers the advantages of high productivity from both human and capital resources as well as high rates of production. Experience suggests that it will be advantageous to extend strip mining to the maximum pos- sible depth in order to minimize costs and maximize the recovery of the in situ coal reserves. Highwall and spoilheap stability pose significant problems. Deep working in strip mines is likely to produce a change from methods which are based upon the elevation of material followed by dumping, to methods involving elevation and horizontal transport. There is considerable scope for optimizing the types of machines and minimizing the amount of double handling.

Jan 1, 1975

To help meet the challenge of mine finding at the start of the 21st century, the exploration geophysicist will have at his command a powerful range of tools, some new, some improved, and some which already exist today but are as yet little used. Remote sensing, using satellite and aircraft-based multi-spectral scanners, will provide the means for routinely mapping the surface distribution of certain carbonate rocks, clay and ferrous alteration minerals, based on the analysis of solar reflectance spectra. Time and emission-spectral resolved laser-induced fluorescence will likewise map the distribution of certain ore and pathfinder minerals, as well as certain skarn zones, all potentially related to ore deposits. The GPS (Global Positioning System), based on 18 orbitting satellites, will provide a universal, three dimensional, all weather navigation system which will completely supplant all existing aerial navigation systems, and greatly facilitate aerial surveying and automated processing and presentation of the data. Aeromagnetic gradiometer measurements will provide higher geometric resolution which will yield better definition of individual geological units. Multi-method ground geophysical surveys will be greatly expedited through the use of portable microcomputer-based, multi-sensor instruments. These instruments will interface with other intelligent devices for automated processing, presentation and interpretation of the ground field data. Borehole geophysics will come into more general use, both for at-hole measurements, especially using active nuclear techniques for grade determination, and for remote detection using a variety of electrical, magnetic, seismic and other methods.

Jan 1, 1986

By Kobayashi M

Particulate chalcopyrite samples (78 ~ 98 mole per cent chalcopyrite, screen size fraction from 710 to 250 µm) were prepared by crushing and sieving lump ore samples from 12 locations in the Mt Isa Mine. Measurements of thennoelectric power (which does not involve the passage of a current) were made using a packed bed that was compressed by loading with a weight and placed in a temperature gradienL Details of the apparatus are described.The effect of particle size was investigated by preparing 12 fractions, with mean particle sizes ranging from 605 to 2.2 µm, from one of the ore samples. Values of thennoelectric power decreased with both increasing particle size and loading pressure; however it remained fairly constant for particle sizes above 80 µm, when loading pressure exceeded 3.3 MPa.Measurements of the chalcopyrite samples gave an average value of -260 JlV/K (-248 ~ -268 µV/K) for nine samples and about -290 µV/K for three samples, showing that these samples were all n-type semi-eonductors.

Jan 1, 1990

By Grieveson P, Rajakumar V

The reduction of an ilmenite concentrate with coal at 1000, 1050 and 1100¦C was investigated using thermogravimetry and X-ray diffraction, optical microscopy and electron probe microanalysis of the product. The effects of temperature, coal particle size, addition of ferric chloride and preheating of the concentrate in argon on the reduction kinetics and mechanism were determined. The rate of reduction increased significantly with temperature and was enhanced by the addition of the catalyst. The morphology of the iron was primarily determined by the degree of weathering of the particle. Significant coarsening of iron was obtained in the dense particles by the addition of ferric chloride. The sequence of reduction and the enhancement in the rate of reduction by preheating the concentrate in an inert atmosphere are discussed.

Jan 1, 1991

By Hiddlestone D. C

Effective exploration, testing and analysis is essential for good process design and optimisation of coal preparation plants. Coal processing relies on the sizing and washability characteristics of the particular coal to define the most cost effective design to meet the market requirements. Flowsheet development and equipment selection is dependent on the natural quality characteristics of the coal, its physical properties and the value of the final product in its market. The methodology of process selection and the key elements in design are discussed. Coal is consumed in two general markets: ò steaming coal - both domestic and export, and ò metallurgical coal. This paper discusses the typical economic analysis required to evaluate the potential for, and cost benefit of, providing the flexibility to switch coals between markets. A case study illustrates the methodology of process selection in a typical high value metallurgical coal.

Jan 1, 1997

By Heyer T, Wasmuth H-D

The concentrator plant of Fahrica Mine, that started production in 1977, was using nine Jones wet high intensity magnetic separators (WHIMS) of the standard type DP 317 with a 1.5 mm gap width for the production of pelletfeed concentrate. These WHIMS units were operating in parallel with a feed rate of 110 t per hour, with about 47 per cent Fe in the feed, and with a maximum of only 0.8 per cent magnetite. The field strength was about 1.2 Tesla. From 1986, the mine has adapted its production facilities to mine and concentrate larger amounts of lowgrade itabintes to maximise the use of the available iron ore reserves. An increase of up to three per cent magnetite in the magnetic separator feed, resulted in a reduction of capacity. This was due to partial clogging of the separation boxes at high field intensities, which were required for the recovery of the very fine hematite. Even by lowering the feed rate and the field intensity the problem could not be resolved. After extensive testwork in a pilot plant, with a Jones separator model DI' 90, the commercial WHIMS plant was modified into a two stage process using the existing nine Jones separators. The gap of the first stage with four machines was increased to a width of 3.5 mm, corresponding to a maximum field intensity of 0.7 Tesla. This first 'medium intensity scalping stage' is followed by a second 'real' high intensity WHIMS step with five machines operating at the original settings with 1.5 mm gap width and 1.0 Testa maximum field intensity. Feed rates of up to 320 tons per hour in the first and up to 240 tons per hour in the second stage could be achieved. The design concept of the concentrator at Fabrica mine is described using the old and new flowsheets. Details of the pilot plant testwork as well as actual performance data of the new plant section are presented.

Jan 1, 1993

By Lee H. G, El-Rahaiby S. K

The literature relating to reduction of sulphides by carbon using lime as sulphur-absorbent is reviewed. A stage-wise thermodynamic model is employed to evaluate the practical feasibility of the direct reduction smelting of galena (PbS) concentrates with a carbon reductant in the presence of lime; a coke-rate of 65 kg/ton Pb is predicted by the model. The experimental data on the reduction of PbS:4CaO:4C mixtures under nitrogen were correlated by means of a finite difference numerical method and the values of the intrinsic rate constant I1 were derived. The results for the uncatalysed reduction are represented satisfactorily with log I1 = 1.247(±0.522) - 5540(±610)T-1.The catalysed PbS:4CaO:4C mixtures contained 2.5 wt% of ternary (K, Li, Na)2CO3 catalyst. For the catalysed reduction it was found that log I1 = 3.981 (±0.301) -7790(±353)T-1, where I1 (in both relations) is expressed in moles.(g.C.)-1.atm-1.s -I. The catalytic enhancement faclor was found to be quite large in the 1068 to 1262°K temperature range investigated here.

Jan 1, 1991

The mine manager is one of the oldest jobs in the world. Over many centuries the fundamentals of how this job was approached did not change much. However since the later part of the 1980s there has been a dramatic shift in the expectations and role of the mine manager as the pressures of globalisation and consolidation have increased the size of companies and the production levels of mining operations. The changes have been dramatic, with demanding requirements on mine managers to continually improve the skill levels of people, to apply and develop rapidly changing technologies and to consider far broader business issues that need to be managed in a truly globally connected world. This paper will attempt to outline some of the issues, the complexity surrounding them and some of the approaches that have been made to manage them. There is not a single correct answer or approach, but there are many key success factors that have led to some amazing levels of performance being achieved as we go deeper, broader and literally move mountains to meet the customerÆs needs for today and tomorrow. This contrasts with many mining operations in developing countries that still have a traditional approach to how they mine. Society is the river of life that continually flows and changes the environment that surrounds it. The pressures from the customers and world growth, shape and force alterations to be made in an industry that has to live with the far greater primal and uncompromising forces of the earth we mine. This has led to some paradigm shifts in how we accept what we manage. TodayÆs mine manager must manage a far broader range of issues, than just how do we get tonnage out of the mine and product out of the ore. These include but are not limited to technical, commercial, product quality and end use understanding, employee and community issues, environmental and the ever increasing complexities of sustainable development. Organisations will have to look at how they structure their management of the business to manage functions to meet the complexity of different stakeholders needs û the business, the employees, the customer and the broader community within an environment that is becoming more attuned to the harm impacts to the world in which we operate. The attraction and retention of skilled people that contribute to the value and worth of the corporation, will become critical to sustain a companyÆs growth. One of the fundamental elements of successfully doing this will always be the skills of the mine manager and his/her extended team with the continued development and support that they will need to meet these demands.

Jan 1, 2006

By Blain CF

For all mineral resource-based companies, it is important to reach the right balance of investment between acquisition and exploration to allow the best chance of achieving long-term corporate goals. The Broken Hill Proprietary Company Limited (BHP) provides an excellent example of success from generative exploration and supports the belief that exploration can be justified, not only in terms of investment criteria, but also because it is essential to a company wishing to build a dynamic profitable growth path based on world-class deposits as cheaply as possible. BHP was incorporated in 1885 to mine a lead/zinc/silver discovery at Broken Hill. The Company has since gone through a steel development phase (1911-1965) and is now in a major phase of growth partly based on exploration success. This third phase was marked by decisions taken in the 1950's to search actively for mineral and energy resources above and beyond the requirements of the steel industry. The commercial successes of this period have been Bass Strait oil and gas, Groote Eylandt manganese, Deepdale iron ore, Gregory coal and Carnilya East nickel. In total at least 22 new resource discoveries have been made in the last 25 years, of which 11 have been developed and several are undergoing feasibility studies. A financial analysis shows that the real value of the returns seeded by discovery covers the real exploration cost many times over. Moreover, the major discoveries have had a spectacular impact on the growth and development of the Company. BHP's present exploration effort is directed towards geological targets which most frequently meet attractive financial criteria and also promote diversification from steel-related earnings.

Jan 1, 1986

By Hematian J

A high horizontal stress field has significant effect on the stability of underground roadways and influences the design of a support system in this environment. The high horizontal stresses at E1lalong Colliery, NSW, Australia provided the environment for this study. Samples of coal measures 'rock were collected and tested to determine their mechanical properties. The lithology, stress state, geometry and conditions prevailing in particular areas of the mine were obtained from geotechnical reports available at the mine and by field observation. The results of a series of finite element models constructed and tested under various conditions provided a basis for comparison with field observations. Analysis of the results indicated sufficient correspondence to provide a basis for the proposed design of an optimum support system. It is not suggested that finite analysis provides 'exact answers', but it does show the relative importance and interaction of various parameters.

Jan 1, 1995

By Marquez W

Trace fossils have been found in Bolivian Silurian sediments in "La Iumhre" area close to La Paz-Bolivia.Tracks, are good indicators of depth and environment. A detailed study of the ichnogenus is made.The depth and environmental deposits are analyzed to determine the facies. It was shown that the trace fossils of Silurian sediments in La Paz belong to the Zoophvcos and Nereites facies.

Jan 1, 1990