Search Documents

By Sakai S, Suga S, Bisque RE

Soil gases were collected on activated charcoal, analyzed by computerized mass spectrometry and treated with multivariate statistical pattern recognition to determine the diagnostic geochemical signature associated with the Okuaizu Geothermal Field in Japan. From this a geothermal model was developed and compare to 175 "unknown" samples in a 250 m spaced grid over 30 1Qn2 mapping the areas with a matching geochemical character. Faults and fractures were generally located by the presence of high molecular weight components. Following the initial survey, the faults in two specific areas were precisely located by a second survey with samples at 10-30m spacing. Where earlier geochemical surveys had placed anomalies 1-2 Km northeast of the geothermal center, the fingerprint survey accurately mapped the system and detected several faulted zones. It was not misled by hot springs located away from the geothermal System.

Jan 1, 1987

An exploration and preliminary mine design contract was undertaken in Thailand to establish whether adequate lignite resources existed for the addition of future power generation plant through to the year 2000. The lignite ranges in heat value from 14 to 24 MJ/Kg (air dry basis) and occurs in 2 major seams consistituting measured reserves of 536 Mt (with an ash cut-off level of 45 % on an air dry basis) and a strip ratio of 4.1 bank cm/t. The paper describes the pre-planning, programming, equipment used, project management, logistics and exploration methods adopted to undertake the contract in a monsoonal area using Australian drilling and geophysical contractors.

Jan 1, 1983

By Restarick C. J & Stewart P S B, Kelsall D. P

Over a four-hour period of steady plant operation samples were taken at regular intervals from points within the grinding and flotation circuits. Size fractions of each composite sample were analysed for lead and zinc values and a comparison made of the behaviour of the lead, zinc and gangue minerals, size by size throughout the whole circuit. Analysis of the breakage behaviour using dynamic mathematical models gave the rates of breakage of each size fraction of each main component. Simulated grinding experiments showed that the main grinding circuit had sane reserve capacity. In the lead flotation circuit all lead values between 150 mesh (Tyler) and 5 microns had excellent flotation characteristics, and a major proportion had a high rate of flotation which was practically the same for all sizes. Increase in overall lead recovery would require improvement of the flotation behaviour of ultra-fine lead minerals. These were slow floating and were responsible for approximately half the lead losses in the final zinc concentrate and one third of the lead losses in the final tails.

Jan 1, 1980

By Wilson J. R

The main mining method employed at Mt Lyell is sub-level open stoping with a typical extraction level interval of 100 m and sub-level intervals of 30 m. Currently, pillar blasts provide the major portion of broken ore and firings are in the order of 200 000 to 300 000 tonnes while future firings of 500 000 to 300 000 tonnes are planned. Improvement of blasting techniques in these mass firings has been necessary for the following reasons. 1. Extremely wet ground conditions have adversely affected ANFO performance and placed extreme pressure on the charging and priming phases. 2. As pillar blasts increase in size the problems of wet ground conditions are accentuated resulting in very slow loading of wet upholes with cartridged gelignite and unreliable charging of the remainder with ANFO. 3 Fragmentation in pillar blasts has suffered because of the above, result- ing in increased secondary breaking costs and difficulty of extraction.

Jan 1, 1977

Rock formation at shallow depths is generally associated with complex geology consisting of many joints, fractures, bedding planes, etc. Fragmentation results from primary blasts in such strata are therefore significantly influenced by structural discontinuities. To evaluate the role of discontinuities, which is of great use in the design of blasts in such conditions, a two-stage investigation program was taken up. In the first stage, model scale tests were conducted with single and double holes with the strike of discontinuities parallel and perpendicular to the face. Later, field studies were conducted in a limestone mine and a coal mine. Blast patterns were modified based on the results obtained from model scale blasts. Secondary blasting was taken as a measure to assess blast performance in the field, whereas mean fragment size, fine and coarse fragmentation indices were considered as fragmentation measures in model scale tests. Model tests indicated confinement of explosive energy by the discontinuities surrounding blasthole. Crater shape and size were significantly influenced by the orientation of joints with respect to the face. Modified blast designs with decreased burden x spacing patterns resulted in improved fragmentation in the field. A reduction of about 12 per cent in explosive consumption was recorded with modified blast designs. Boulder formation was observed to decrease by about 79 per cent as well.

Jan 1, 1995

An on-stream iron ore analyser has been developed in collaboration with Hamersley Iron Pty. Limited for determining the iron content of both lump (- 30 + 6 mm particle size) and fines (- 6 mm particle size) on conveyor belts. The analyser, which is called IRONSCAN, is based on pair production, and is now commercially available from Mineral Con- trol Instrumentation Limited (MCI) in Adelaide. It can be mounted under existing conveyor belts with minimal modifications to the conveyor struc- ture, and the presence of steel cables in the belt does not interfere once the analyser has been correctly calibrated. The analyser has been exten- sively tested on both lump and fines on the shiploading conveyor at Damp- ier, and typically the root mean square (r.m.s.) deviation between single IRONSCAN measurements and conventional chemical analyses is better than 0.5% Fe. It is currently being evaluated on - 150 mm ore from the primary crusher at Mount Tom Price, and initial results are encourag- ing. The principal advantage of IRONSCAN is that it provides rapid infor- mation on ore grades. But perhaps its greatest potential is at the primary crusher where conventional sampling and analysis is very expensive to Implement. at the University of Melbourne, and those of us who were his students had learnt of the application of physical chemistry to pyrometallurgical processing, pioneered by Chipman in the USA, Wagner in Germany, and Richardson in the UK. It was possible, by applying this theoretical insight to the equilibria between metal, speiss or Legierung, matte and slag phases, to find a practical and effective way to recover metal values in some residues which had been accumulating for many years at the NA, but which had defied all attempts to treat them to that date. There was also an opportunity to study the batch lead refining methods still in use at all lead refineries apart from Port Pirie, and to devise optimis- ing techniques which greatly improved the operations and effected considerable savings. Next the writer spent some six years alternating between the BHAS, Port Pirie, and Imperial Smelting at Avonmouth in the UK, concerned with lead or lead-zinc smelting, and the develop- ment of several further continuous lead refining processes, before returning to Australia as Section Leader, Process Development in the CSIRO Division of Chemical Engineering, Fisherman's Bend, Victoria. Metallurgical opportunities which arose during this last period included the problem of tin smelting which had developed over about a decade: the world's tin smelters had been accustomed to treating fairly high grade tin concentrates, con- sisting of almost pure cassiterite, with very little impurity-mostly quartz, limestone, iron oxides, and sundry other silicates. Most such concentrates had been produced from alluvial deposits, where nature had already done some of difficult part of the mineral processor's work-at who knows what recovery-so that he could now produce high grade concentrates at high recovery. The smelters were not really set up for the treatment of lower grade concentrates, such as could be made with reasonably high recoveries from rock mining. Thus they imposed such penalties on impurities and lower than desired tin grades, that whenever a mineral processor improved tin recovery at the expense of lower- ing grade, such an improvement entailed a lower financial return to the miner. There was clearly a need for improved understand- ing of tin smelting, (at that time shrouded in secrecy) and develop- ment of techniques better suited to the treatment of lower grade concentrates. As well as the practical development, a start was made with the computer modelling of the smelting process, with the obiect of optimising the process parameters.

Jan 1, 1988

Most types of nuclear power reactors use uranium dioxide fuel. Power reactors using natural uranium dioxide'fuel are of special interest to countries such as Australia that have their own uranium supplies. A wide range of uranium dioxide powders can be fabricated and the ideal one flows readily, presses without the need for binders or lubricants, sinters to the required density and gives low reject rates at all fabrication stages. Sinterable uranium dioxide is usually produced via the ammonium diuranate route. The A.A.E.C. is aiming to demonstrate production of nuclear grade uranium dioxide from Australian concentrates, improving technology where possible. Details are given of the dissolution, solvent extraction, precipitation, filtration, drying, and calcination-reduction steps. Solvent extraction from sulphate media is also under study with a view to developing a process to produce a nuclear grade product at the mine treatment plant site,

Jan 1, 1969

Using normal low pressure filtration methods for the dewatering of fine china clays, the best that can be achieved is cakes with about 30% moisture. In order to get the moisture levels down to acceptable levels the traditional method used is thermal drying, which is both costly and dust creating. It was to improve this process that ECC International embarked upon a programme of development of filtration equipment using high pressure to achieve significantly lower moisture levels. This development work investigated several design philosophies and culminated in the production of two quite different solutions. The High Pressure Plate Press uses round plates / chambers of one metre diameter and a filtration pressure of 70 bar. This press is fully automatic and produces a surface dry cake that has sufficient plasticity for the further processing that is required on specific qualities of china clay. The TUBE PRESS on the other hand uses a unique design configuration and operates at a filtration pressure of 100 or 140 bar, depending upon the model. The TUBE PRESS produces a brittle, surface dry cake that is easy to handle and a filtrate that is usually crystal clear. The TUBE PRESS achieves a much higher degree of separation than is possible with conventional equipment, which is particularly important if the filtrate is the product. Over the past 15 years plants incorporating both HP Plate Presses and TUBE PRESSES have been installed in the china clay operations of ECC International and are giving excellent trouble free service. The TUBE PRESS has also proved to be extremely versatile, effectively dewatering a wide range of fine particled slurries, in a number of diverse industries.

Jan 1, 1989

The physical phenomena which influence gas flow in the bosh and hearth of a blast furnace are discussed including the hold-up of slag as a mechanism which can result in a flooding condition. An equation is defined which describes the limitation to wind volume arising from the flooding condition. Implications of the various factors influencing bosh and hearth gas flow on furnace operation are discussed. Coke quality is shown to be the most important factor in the aerodynamics of these zones and coke requirements are defined for the Port Kembla No. 5 BF which has an inner volume of 2670 m3.

Jan 1, 1975

The Lower Proterozoic metasediments of the Pine Creek Geosyncline form a chrono- stratigraphic sequence of mainly greenschist- and amphibolite-grade shallow-marine to supratidal pelites, psammites, carbonate rocks, and volcaniclastics which in places rests unconformably on Archaean basement. Granite and later dolerite intrude the sequence, and are associated with the major orogenic 1800-m.y. event which regionally metamorphosed the sediments. Most mineralisation is stratabound, and can be related at least partly to volcanic activity. Uranium mineralisation is mainly confined to particular carbonate-rich horizons near basement. Other metals are mainly in small hydrothermal deposits near intrusive granite. Specialist studies indicate that uranium was leached from its source rock, and probably carried as carbonate complexes in highly saline fluids at between 100 and 3500 C. Precipitation took place by redox reactions in breccia zones in carbonate rocks; these zones were formed by carbonate solution or diapiric movement of evaporites which preceded the carbonate. Extensive chloritisation in the ore zones suggests metasomatism by Fe- and Mg-rich fluids which may have evolved during dewatering of the evaporites. The main mineralising event took place after the 1800 m.y. metamorphism, and was probably

Jan 1, 1979

By Brumley J

The development of the SECV brown coal open cut at Loy Yang will require depressurisation of aquifers both within and below the coal seam sequence in order to maintain open cut stability. Prediction of future open cut dewatering requirements at Loy Yang Open Cut and evaluation of the regional consequences of dewatering has required development of a detailed hydrogeological model of the Loy Yang area. The complex stratigraphy of the coal seam and aquifer/aquitard sequences at Loy Yang have been analysed and integrated with the hydrogeological concepts developed from regional groundwater studies to formulate a realistic hydrogeological model as a basis for finite-element flow modelling.

Jan 1, 1988

By Yamada K, Abe H

Magnetic scanning type mass spectrometers have been given improved sensitivity with a large dynamic range and considerable resolution by the addition of a computer-controlled electric equipment. A mass spectrometer equipped with this newly developed electric system was applied to studies of the activities of liquid iron-silicon alloys and of liquid iron-phosphorus alloys at 1600¦C. The range of silicon concentration was 5.8at%-51.1 Si= at%, and values of ySi -3.1+0.15 and es 11.5 +1.5 were obtained. The concentration range of phosphorus was 1.3at%-5.7at% and a value of eP=7.3+0.1 was obtained.

Jan 1, 1980

By Agrawal A, Joshi A

Mochia mine, in culmination of depillaring operations, fired India's largest underground pillar blast consuming 145 tonnes of explosive and yielding 0.55 million tonnes of ore in June 1994. To protect main mine structures (situated at a distance of 250 to 350 m from the blast site) from resultant ground vibrations, the charge per delay was restricted to 2300 kg. The post-blast observations revealed that no damage was caused to these structures. However, the damage assessment survey of the mine workings situated in close proximity revealed a general trend in consonance with the distance from the blast and found to be well correlated with peak particle velocity.

Jan 1, 1995

Feasibility is a value improvement process for projects. At any stage in project development, a feasibility study can be undertaken, but although the scope generally remains unchanged the extent of detail and level of accuracy usually increases with time. The main scope elements are a business definition, project description and an execution plan. The studies are designed to assess the potential of the project and to secure funding for on-going examination. Invariably, the investigations loop back to earlier stages to establish more appropriate development criteria but a critical stage is reached when a project construction decision is requested. This feasibility study requires very detailed presentation and analysis to a higher accuracy for the owner(s) and their potential lender(s).

Jan 1, 1997

By Gooday PE, Brech GE

Ore reserve categories used by Pancontinental Mining fall into one of three fundamental groupings: Geological In Situ Reserves Mining Reserves Production Estimates The first of these describes the total reserve within stated parameters without implication as to its mineability. The second is that part of the Geological In Situ Reserve which is considered mineable under a specific mining plan. The third is the Mining Reserve adjusted with appropriate dilution and recovery factors and thus represents the best estimate of the tonnage and grade of production. This practical three category system mirrors the standard steps traditionally taken in ore reserve estimation and readily conveys the basis of the estimates. An important, but secondary classification can be added to qualify the level of confidence in these estimates using the terms: Proved (or Measured) Probable (or Indicated) Possible (or Inferred) These terms can be applied to any of the fundamental groupings, but it is generally implicit that the level of detail required to produce meaningful Mining Reserves or Production Estimates would require the basic Geological Reserve to be at a Proved or at least Probable level of confidence. The application of these classification systems by Pancontinental is illustrated by reference to the Paddington Gold Project. The methods of calculation are described including the use of geostatistics. Reconciliations of actual production with predictions from reserves are carried out monthly and annually. To date there has been an excellent correlation with Production Estimates, based on both manual and geostatistical calculations.

Jan 1, 1987

By Grobler H. P, Chitombo G. R

Production blasting of Dc Beers Consolidated Mines Limited, Koffiefontein and Finsch Mines involves both uphole trough rings of 9 to I I holes and near vertical 360 degree compound rings of 42-54 holes. The rate of production from these stages is dependent upon being able to achieve a specified fragmentation size range and this has driven the derivation of blasting practices to consistently achieve this target fragmentation. At the Dutoitspan Mine, in Kimberley, where mining of the kimberlite pipe is by block caving, 100 per cent extraction of the undercut level by ring blasting is essential. If this is not achieved, pillars are formed which not only inhibit the efficient initiation of the caving process, but also concentrates load onto the extraction level, causing damage to draw points and pillars. These two case studies demonstrate the importance of achieving optimum blasting performance for downstream mining efficiency; ie fragmentation for increased productivity at Koffiefontein Mine and 100 per cent undercut extraction for efficient initiation of the caving process at the Dutoitspan Mine. The case studies also serve to highlight the long road towards blast optimisation taken by De Beers Consolidated Mines Ltd (Koffiefontein. Finsch, Premier and Kimberley Mines) since 1989.

Jan 1, 1995

By Stokes WPC

The capital requirements to develop a new mining venture are becoming very large; amounts of the order of US$1,000 million are not now unusual among estimates to bring new mining complexes into production. At the same time prevailing political and economic conditions are making it increasingly difficult to determine whether or not a project is likely to be viable. These factors emphasise the need to carry out thorough evaluation studies of all mineral prospects before making major investment. Additionally with the rapidly changing economic climate existing at the present time, it is becoming more and more necessary to carry out reappraisals of existing mines. An important function of both initial evaluations and reappraisals is to provide the operators of the mine with effective mining plans to ensure that the operation will meet its required economic targets. P, p M. tl p b, c v, s c 1 n 1 f r d c e c e u w Modern computers are well equipped to store and manipulate large amounts of data with speed and reliability. Their use in the mining field r is increasing and this trend serves to free f technical staff from much of the time consuming m and error prone hand calculations which were o formerly required in determining reserves and w carrying out all forms of mine planning. r Nevertheless, computers are not a universal

Jan 1, 1980

A number of cooperative studies have been carried out as preliminary work for drafting a standard for application of granulated slag sand for concrete, and the following conclusions were reached 1 The ten kinds of granulated slag sands pro- duced in Japan satisfy the national standard for fine aggregate in terms of physical and chemical properties. 2 Mortar and concrete tests conducted with granulated slag sand revealed that, although with slight differences in the extent, gran- ulated slag sands used in these tests were applicable'as fine aggregate for concrete, 3 The pumpability test by a concrete pump carried out on concrete with two kinds of now commercially available granulated slag sand demonstrated that the pump pressure feeding is applicable in the same manner as in the case of ordinary concrete. These tests permitted' preparation of a draft standard for application of granulated slag sand, and the results formed the first step toward utilizing this material as a sub- stitute for natural sand.

Jan 1, 1979

By Lawrie DC

Finely ground beryl was decomposed by mixing with ground limestone and soda ash andheating at 900¦C for,4-6, hours.The sintered material was then crushed and leached by boiling under reflux with 5N sulphuric acid for up to 4 hours. The liquor containing Be, ; Al, . Fe and, other elements as sulphates, was separated from the residue which consisted mainly of silica and gypsum, either' by filtration or by decantation washing.The clarified leach liquor.was first treated to remove Fed}: , by contacting with a primary amine-kerosene solution in2 counter-current stages. The iron free liquor wa,s then passed to a 4-stage counter-current extraction unit where it was con-tacted with 0.5M di-(2 ethyl hexyl), phosphoric acid (EHPA) in kerosene. The'operating conditions were such that at least 99 p'br cent of the Be and only 7' per' cent of the Al- was, extracted The ,B6`= and. Al were ;stripped from the organic phase by sod-ium hydroxide solution of suitable concentration to form soluble "beryllate" and "aluminate" respectively. Most of the Be was subsequently precipTitated a's Bo(OH)2 by-hoating the alkaline solution to 90C, the Al remaining in solution. After filtra-tion and washing, the Bo(OH)2 could be ignited directly to BeO at about 1000 C or used as a feed to further purification stages aimed at producing "nuclear grade" BeO.A small coaAter-current extraction unit was operated con-tinuously using liquor derived from the sintering and leaching stages. Data obtained in batch laboratory tests were confirmed. A product obtained by ignition of the washed "beryllate" precip-itate contained more than'99 per cent BeO.

Jan 1, 1963

In the five years since Great Central Mines Limited (GCM) commenced exploration in the Jundee and Bronzewing areas of Western Australia's Yandal greenstone belt, the Company has been transformed from a junior explorer into Australia's fourth largest gold producer with annual production of approximately 440 000 ounces and mineral resources of seven million ounces of gold.The growth in resources has been driven by a high quality geoscientific approach, supported by a substantial budget for drilling and strong management commitment. In 1997, the Company expects to spend US$30 million on exploration in the Yandal greenstone belt.

Jan 1, 1997