Search Documents

A fundamental component of grade control at Tarmoola Mine has been the monitoring of assaying through quality assurance programs. The programs have concentrated on issues related to accuracy and precision of leachwell and fire assay techniques, sample preparation and grade variability within a sample. An outcome of monitoring has been identification of shortcomings in the application of assaying techniques to Tarmoola ore types that contain coarse particulate gold. Leachwell has shown satisfactory precision since introduction as the primary assay technique in October 1998 but leachwell accuracy and recovery through comparison with fire assay techniques has identified bias. A bias toward higher fire assays in grades above 2 g/t invoked an investigation into the cause of the discrepancy between leachwell and fire assay. Testwork evaluated Leachwell assay recovery by varying leach time duration, which showed that by increasing the leach time improved recovery significantly. Monitoring of leachwell against fire assay had shown that a leachwell (200 g) with a one hour leach has under-called grade when compared with fire assay by up to 18 per cent, on average, for Tarmoola ore types. Alternatively, optimisation of the leachwell assaying technique using a 200 g pulp and a two hour leach has returned, on average, higher assays than fire assay by up to eight per cent. Testwork on screen fire assays, duplicate assays and fire assay to extinction has demonstrated assay variability associated with coarse, particulate gold. The variability and distribution of gold in Tarmoola ore types has emphasised the importance of high quality sample preparation for leachwell assaying to ensure liberation of gold to leaching solutions. Assay quality assurance protocols are vital to assay data integrity and enable confidence in delineation of ore-waste boundaries and provide early recognition of problematic assaying periods and isolation of grade control practices, which depart from performance standards critical to the operation.

Jan 1, 2000

By A Asadov, D Nair

This paper discusses the determination of the percentage of crystalline material in a natural silica deposit which would be considered harmful to health (<10 ¦m). A sample of the natural silica material was recovered and split into a number of subsamples. Samples were sieved using a conventional dry sieve to remove material >300 ¦m before testing. Particle size analyses of the fine fraction showed 75 per cent of the material was below 10 ¦m. Initially XRD and XPS were run on the samples to determine the minerals and composition of the sample. The XRD revealed strong quartz peaks and smaller tridymite peaks with a high amorphous background. The XPS indicated traces of iron, titanium and carbon with dominant silicon and oxygen peaks. The structure of the sample was investigated using the SEM. It was apparent that there were a number of larger quartz crystals (>30 ¦m) with a mix of amorphous and crystalline in the finer fraction. It was also observed that amorphous material was attached to the surface of the crystals. In order to determine the percentage of crystalline quartz a known amount of quartz was added to the sample incrementally. On each addition an XRD scan was performed and the area under the peaks recorded. Back analysis of these peaks with an assumed percentage of crystalline material in the original sample gave a crystalline content of 30 per cent. The quantity at the respirable fraction was estimated to be 18.7 per cent.

Jan 1, 2003

By V L. Los, G J. Abramson

The paper examines three types of polar zoning of ore-forming and associated elements that can be detected from geochemical data. Polar zoning is mapped in the form of geochemical ore systems of various ranks. Various types of polar zoning can be found in some systems, which present a general geochemical model of the ore object. The genetic basis of zoning is examined from the perspective of the conception of geoelectrochemical redistribution of matter, including ore-forming elements. The volume of the geochemical ore system may be used in the prognosis of resources for every rank.

Jan 1, 1999

By J W. Dong, Y M. Li, J L. Tian, Z H. Jiang

Electroslag remelting is widely used to produce various special steels, mainly because of its ability to provide high cleanliness and excellent homogeneity of ingot. Undoubtedly an optimal slag plays a key role in removing inclusions and enhancing the mechanical properties of a specific special steel. In order to improve the metallurgical performance of the slag in electroslag refining of die steel, a variety of slags have already been developed using traditional trial-and-error methods. Nonetheless, these slags may not be inherently optimal for the specific requirements of actual die steel refining processes. In this work, we have designed a CaF2-CaO-Al2O3-SiO2-MgO quinary slag system using genetic algorithms method aiming to remove the existing large size inclusions (D and Ds type) in high quality die steel. The comprehensive effects of five components (CaF2, CaO, Al2O3, SiO2 and MgO) were studied based on existing fundamental theory. The slag composition was screened considering the parameters such as melting point, electrical conductivity, calcium ion concentration, and appropriate viscosity etc. Furthermore, the candidate optimal slag was applied in the industrial production of die steel by electroslag remelting method. The detection results indicate that majority large inclusions (D and Ds type) have been successfully removed, showing significant advantage to traditional slags. This result has demonstrated the genetic method to be efficient and reliable. In addition, depending on the personalised demand of other steel and alloys, this method allows for the adjustment of the screening frameworks and processes to develop the candidate optimal slags. This method has not been reported previously in the field of electroslag composition design, and compared with the traditional trial-and-error method, the new method will save a lot of time and experimental costs.

Jun 19, 2024

By D Craw

Previous studies of alluvial gold in Otago and Southland placer deposits have suggested a gold-mercury association for some deposits derived from Caples Terrane schist, whereas alluvial deposits on Torlesse Terrane basement typically have no mercury. A regional study of gold from Otago Schist vein deposits from both Caples and Torlesse Terranes has revealed the presence of both Au-Ag and Au-Ag-Hg alloys in both terranes. Au-Ag alloy (3 - 4 wt per cent Ag) is typical for gold found in most Torlesse vein deposits, and Au-Ag-Hg alloy (3 - 8 wt per cent Ag, 2 - 8 wt per cent Hg) is found in many Caples vein deposits. Au-Ag-Hg alloys are not exclusive to the Caples Terrane, however, as Au-Ag-Hg alloys with up to 4 wt per cent Hg are found in vein material from the Torlesse-hosted, HydeMacraes Shear Zone. In addition, not all Caples-hosted deposits have a gold-mercury association; gold grains from the Carrick and Invincible gold fields have no detectable mercury. The present study characterises gold compositions from various hard-rock vein deposits and has potential for determining placer-source relationships.

Jan 1, 2003

By D Craw

At Reefton, mesothermal gold deposits occur in the Ordovician Greenland Group basement and bituminous coal deposits occur in overlying Eocene Brunner Coal Measures. These different resource types occur in close proximity to one another in the same topography, vegetation and climate. Both types of resources have been mined for many years and as a result historic mining areas discharge water with chemistry reflecting the mineralogy of the deposits. Coal measures release natural acid rock drainage throughout the region due to oxidation of pyrite in coal and associated sediments. Levels of acidity are increased in mining areas, and pH near three is common. Gold mines contain pyrite, arsenopyrite and stibnite. Discharge waters from these sites have pH near seven because of the high acid neutralising capacity of the basement rocks. Both coal and gold mining sites have iron oxyhydroxide precipitates in drainage waters. These precipitates are more abundant at gold mining sites, and one deposit is up to 5 m thick. Iron oxyhydroxide at coal mine sites contain Zn (up to 89 ppm), Ni (up to 10 ppm), As (up to 163 ppm), Cr (up to 23 ppm), Pb (up to 16), and Cu (up to 11 ppm). Jarosite group minerals have been identified in the coalmine iron oxyhydroxide, although most of the material is amorphous. Gold mine iron oxyhydroxide contains Zn (up to 353 ppm), Ni (up to 592 ppm), Cr (up to 17 ppm), Cu (up to 72 ppm), Pb (up to 29 ppm), Sb (up to 230 ppm), and this material is particularly high in As (up to 20 wt per cent). Most of the material is amorphous but distinctive zones (mm scale) are As rich (up to 30 wt per cent As oxide). Pharmacosiderite, K2Fe4(As04)3 (OH)5.6.3H20, is a secondary mineral in one deposit. These iron oxyhydroxide deposits are useful indicators for the metals mobilised into the environment by oxidation in the historic workings.

Jan 1, 2003

By H Han, L Lu

Due to the international depletion of reserves of traditional high-grade iron ore, the ore resources available throughout the world, especially in steel mills in East Asia, have changed drastically from hard hematitic to more goethitic ore types, such as pisolitic and Marra Mamba ores. The level of impurities and loss on ignition in iron ore has also been slowly increasing. Finally, the proportion of fine material in the available products has increased considerably for most iron ore fines. This has been found to have significant impacts on sinter quality and sintering performance. Magnetite concentrate is typically high in Fe grade and releases extra heat when oxidised to hematite. The amount of magnetite concentrates is expected to increase due to the recent development of a number of magnetite projects. Some of these magnetite concentrates will end in sinter blends. This will not only improve the sinter quality and but also have a beneficial impact on the fuel consumption of the sintering process. However, most of the concentrates available are very fine, which will negatively impact the green bed permeability and consequently the productivity of the sintering process. This paper reviews and comments on the recent technological advances in sintering with high proportions of magnetite concentrates.CITATION:Han, H and Lu, L, 2017. Sintering technologies of sinter mixtures containing high proportions of magnetite concentrates, in Proceedings Iron Ore 2017, pp 31–38 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

It is now becoming mandatory in Australia to rehabilitate ponded fine grained coal mine tailings, which may well have been deposited initially with no consideration as to how or whether this could be done nor to the costsinvolved. Of prime importance to the rehabilitation of tailings ponds are the bearing capacity and deformation characteristics of the tailings. Since the tailings are fine grained, time effects will govern the self-weightdeformation of the tailings initially deposited as a slurry and the subsequent deformation of the deposit under the weight imposed by rehabilitation fill. The engineering properties of a particular deposit of ponded tailings havebeen investigated and its response to the placement of fill monitored and analysed.

Jan 1, 1987

Mining companies in order to compete and succeed in being viable business propositions must look to the future and select mining methods which guarantee improved efficiency and productivity as well as lower costs. A mining company in adopting a method of mining must now select the equipment most compatible. To some mines compatible equipment may mean the use of drilling jumbos to replace hand held rock drills or the use of load haul dump units to replace scrapers. To other more mechanised mines compatible equipment may mean the use of raise borers and road heading machines. The right decision will be where equipment compliments method in such a way that the working environment is improved, productivity is maximised, cost if reduced and all profit opportunities are optimised. An example of such is where the use of improved mining techniques in underground operations may see cut off grades reduced. By selectively mining these lower grade orebodies, smaller operation's ore reserves improve and the capacity for continued growth is enhanced.

Jan 1, 1990

In coal mining, geophysical techniques have an established application in determining the location of seam boundaries ahead of the face so that underground mines can be planned to avoid any geological structures that might disrupt production. Geophysics can also be used in geotechnical studies to determine the in situ properties of the rock mass and the response of the rock mass to the mining. The use of geophysical logs and microseismic monitoring in these geotechnical applications are discussed in this paper.

Jan 1, 2002

By K Palmer

Alluvial platinum was recovered during gold mining operations in Maud Creek, a tributary of the Howard River. Average electron probe analyses give Pt 88.75, Fe 5.27, Ir 0.70, Os 1.06, Pd 0.34, Ru 0.14, Rh 1.29, Cu 1.06. Rare grains of a Pt-Fe-Cu alloy are also present and an unusual feature of all grains is the relatively high rhodium content which finds expression in segregations of rhodium arsenide, cherepanovite. Platinum is found in the Orepuki area of Southland, where it is probably partly derived from the mafic rocks of the Longwood Complex. Rocks of the Rotoroa Complex, similar to those of the Longwood Complex, form bedrock in Maud Creek and are possibly the source of the Howard platinum. Alternatively, it might be derived by glacial transport from the Matakitaki ultramafic block 30 km to the southwest. Origin from the Rotoroa rocks is preferred as, if the Matakitaki rocks are part of the Dun Mountain Ophiolites, they might be expected to contain osmiridium rather than platinum. The ratio Pt:Ir-Os has been widely used to distinguish low Pt:Ir-Os ophiolitic from high Pt:Ir-Os gabbroic assemblages. Mafic complexes such as Longwoods, Darran, Rotoroa, and Riwaka might be expected to show similar high Pt:Ir-Os ratios and be targets for platinum exploration. Detrital platinum examined from the Parapara area, Golden Bay is mainly osmiridium, with rare grains of rutheniridosmine, very similar in composition to that found in concentrates from the Kaniere dredge, West Coast.

Jan 1, 1987

By M A. Knackstedt

Coupling between deformation processes and rock permeability is a major factor influencing the architecture of fluid migration and the localisation of ore deposition in several types of hydrothermal ore systems in middle to upper crustal regimes. Permeability in many hydrothermal systems is controlled by a dynamic competition between deformation-induced porosity-creation processes and porosity-destruction processes. Localisation of deformation within faults, fractures and shear zones leads to flow localisation, with large-scale flow systems forming when active faults and shear zones link to create percolation networks. Numerical modelling techniques are used to explore the growth of fracture networks and evolution of network connectivity during progressive deformation. Initial results indicate that networks reach a percolation threshold at very low strains. Near the percolation threshold, flow is localised along a small proportion of the total fracture population and favours localised ore deposition. At higher strains, flow is distributed more widely throughout the fracture population and may provide reduced potential for production of high-grade deposits. The distribution of mesothermal gold deposits along a small subset of the total population of co-active faults and shear zones in the Archaean Yilgarn Craton in Western Australia indicates that some hydrothermal systems maintain themselves near the percolation threshold for a substantial part of the lifetime of the system. Fluid-driven growth of fault/fracture/shear networks may lead them to self-organise near the percolation threshold.

Jan 1, 1999

By W Blair, J Bosman

The measurement of ferrosilicon rheology and characterisation of the parameters that have a direct influence on medium rheology provide the basis for evaluating, comparing and selecting an appropriate size and shape of medium to maximise separation efficiency in a dense medium application. The role of medium viscosity on particle separation in both static and dynamic separators is illustrated using relevant theory. The primary measurements of rheology are medium viscosity and stability. These in turn are determined by particle size, particle density and particle shape which in turn can be quantified. Additional characterisation parameters are also discussed. Different areas of application where ferrosilicon characterisation can be used are also discussed.CITATION:Bosman, J and Blair, W, 2017. The practical characterisation of ferrosilicon for dense medium applications, in Proceedings Iron Ore 2017, pp 135–140 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By K J. Thompson

This paper describes the work which has been undertaken at the Ohai coalfields in Southland to restore overburden heaps during past opencast mining operations, and procedures which have been adopted to ensure that restoration is achieved concurrent with present opencast mining activities. The system implemented for the treatment of wastewater from opencast mining operati6ns is also described.

Jan 1, 1981

By D J. Kilkenny

Work practices involved in shaft construction can be aligned with current industry standard operating practices. However, the working environment during conventional shaft construction introduces unique conditions which can not always be overcome by hard engineering controls. To provide an improved working environment, future shaft diameters will generally be greater than has historically been the case for the Australian hard rock mining industry. This paper aims to explore both what can be constructed from the contractors perspective, and how does an owner extract maximum business efficiency from an asset that in many ways is likely to be larger, more complex and more expensive than initially envisaged.Newcrest Mining Limited, or an associated company, has constructed two major shafts over the last seven years. In both cases, Byrnecut Mining, or an associated company, was the contractor engaged for the shaft sinking activity. The first is the 1127 m deep, 7.0 m diameter production and intake airway at the Telfer Gold Mine, the second is a 295 m deep, 5.5 m diameter split shaft at the Gosowong Gold Project in Indonesia that was primarily designed as both an intake and exhaust airway. Importantly both shafts are designed to provide emergency egress from the respective underground operations.From an Australian shaft sinking perspective, the construction of these two shafts resulted in the following learnings: •constructability is of equal importance to desired functionality;•allow six months of interactive design between the owner/engineer/contractor/regulator to get it right;•shaft sinking and equipping are intimately entwined, therefore engineering of both needs to be complete prior to any activity commencing; and•the mobilisation of both equipment and experienced personnel to a new shaft sink takes up to eight months.Shaft sinking is not extinct in the Australian hard rock mining industry. But, if you are considering constructing a shaft, approach it as a long life asset, front end planning to a high level of detail is required to unlock its full value. Think – plan – think and remember it’s going to take 12 months to get from the whiteboard to firing the first cut.

Mar 21, 2011

The New Zealand Steel Ironsand Slurry Pipeline was successfully commissioned in February 1986. The project includes 18 km of high pressure, polyurethane lined buried pipe. McConnell Dowell Constructors Limited has developed a coupling which has allowed this pipeline to be fully welded. The design and development of the coupling and its application on this project is discussed.

Jan 1, 1986

By G C. Sen

All mining and quarrying operations that employ blasting to fragment and move broken ground have a price to pay for æby-productsÆ such as vibration and noise. These æby-productsÆ cannot be eliminated but they can be controlled and modern blasting techniques have improved to the point that excessive environmental restrictions can be adhered to whilst maintaining acceptable production rates and quality. Accurate measurement is the key to control, and as the environmental limits are becoming tighter, the proper way to measure vibrations from blasting operations becomes an integral part of the mining or quarrying operations. The basic vibration monitoring system consists of a primary sensor connected to a data logger and computer software for the analysis of the signal received and recorded. Currently, as with all fields of measurement, much improvement has occurred over the past decade, and electronic devices are much more accurate and reliable. Data analysis has also improved considerably with the computing power that is available to field operatives today. Mounting the primary sensor has been often overlooked in supposed æstandardsÆ with procedures such as double sided tape, resting on a flat surface provided the vibration level is less than a given amount. But if it is worth going to the expense of the monitoring equipment and manpower, surely it is worth a little extra effort to ensure the primary sensor is coupled to the ground effectively. The primary sensor must move with the ground and measure this movement; so if the primary sensor is allowed to move without respect to the ground (ie poor coupling to the ground) then a false record of the physical event will be measured. This scenario can easily be a practical reality if the primary sensor coupling method to the ground is not effective. In this study a number of mounting methods were fabricated and connected to similar data monitors and a series of ænormalÆ production blasts were used as the vibration source. These mounting devices were measured against an in-house procedure (the æstandardÆ) and the relative merits compared. A laboratory investigation was also carried out to look at the physical parameters of the æsoil and their effect on vibration attenuation of the in-house standard method.

Jan 1, 1999

An understanding of the way that solutes are transported in mining or natural environments is essential to the development of sound strategies for managing waste disposal. Research on miscible pollutant movement in unsaturated porous media is carried out both experimentally and numerically. Results of numerical modelling are obtained by solving the groundwater flow equation and the solute transport equation. The finite element method is employed and comparisons between simulation results and experimental data are found in remarkable agreement.

Jan 1, 1995

By S Doudle

The Iluka Resources Ltd Jacinth-Ambrosia heavy mineral sand mine (South Australia) is located in an undisturbed semi-arid landscape consisting of sparse trees, shrubs and grasses. The soil interspaces are covered with biocrusts, a living soil cover also found worldwide in arid regions. Biocrusts are composed of lichens, cyanobacteria, algae, mosses, liverworts, fungi and bacteria, and live on and within the first few millimetres of the soil surface. Biocrust organisms bind soil particles, sequester carbon and many fix atmospheric nitrogen making them important structural and functional components of ecosystems. Despite their important role in ecological processes, biocrusts are susceptible to disturbance; nevertheless they can recover provided sufficient inoculum is present. Cyanobacteria are the early colonisers and they capture atmospheric and landscape resources and establish conditions that subsequent successional seres can capitalise on. Research conducted in countries including China, Spain and South Africa has been focused on methods to either encourage rapid regeneration of cyanobacterial remnants or to introduce new material from cultured cyanobacteria. We have been investigating the extent and diversity of biocrusts across the 4500 ha mine lease and their potential to improve mining rehabilitation outcomes. Approximately 46 per cent of the soil surfaces are colonised with biocrusts and 33 taxa have been identified. Laboratory experiments were designed to mimic massive soil disturbance and treated with a range of water qualities. Within 22 days, treatments irrigated with fresh water were colonised by new cyanobacterial filaments with a mean surface coverage of 65 per cent. Secondary tests revealed that differences in the photosynthetic yield of the crust were dependent on the salinity levels of the irrigation water used. In 2011 this program is expanding from the laboratory into field scale trials designed to assess both the potential and practicalities of up scaling these techniques to provide crushed biocrusts and cyanobacterial bio-inoculum for use in mine rehabilitation.

Oct 5, 2011

By M Lentz

This paper will discuss the issues associated with blasting in an urban mining environment that have been addressed by Winstone Aggregates at the Mt Wellington Quarry. These issues include - control of vibration and air overpressure, repeatability of shot performance, fragmentation on an extremely low maximum instantaneous charge, compliance with Territorial Authority regulations and perception. Over the last two years, in order to address these issues, Winstone Aggregates have undertaken a programme of continuous improvement, which has included; ò implementation of new technology; ò revising site procedures; ò conducting an investigation into the structural response of local buildings; ò investigating safe extrapolation; ò extensive public consultation; ò establishing credibility during the consent process; ò identification of perception issues; and ò building relationships and trust with neighbours. The issues addressed at the Mt Wellington Quarry have increasing significance for traditionally rural mining operations, as the input of the local community being urban or rural, increases. New and existing operations have the potential to adopt best practice now, building trust with the community and raising the profile of the industry.  

Jan 1, 1999