Search Documents

Recently published extensions to the mill-dump cutoff grade theory for joint open pit-concentrator operations lead to equations that must be simultaneously satisfied as a necessary condition for an optimal operating policy. These equations are parametrically dependent upon ore quality parameters, other than grade, relating to the ease of recovery of the disseminated mineral in the concentrator. Since it is not possible to treat quantities of ore corresponding to the size of selective mining units separately in the concentrator some mixing is inevitable and often deemed desirable in the interest of homogeneity of mill feed. This renders the calculation of cutoff grades for individual mining units futile; mining units must be grouped to form larger parcels that can be dealt with separately. In doing so an opportunity cost may be incurred; the loss of potential benefit that would result from such separate treatment. This matter is considered from a theoretical, qualitative, point of view. A numerical example then shows that a significant variability in the quality parameters can be tolerated without incurring such opportunity cost, provided sufficient knowledge is available concerning the distribution and effect of these variables to enable the use of effective mean values of these parameters in the cutoff grade calculation. Lack of such knowledge can have major consequences for the economics of the operation.

Jan 1, 1981

Thirty mixed cultures of microorganisms from soil, water and mineral samples from the Groote Eylandt Mining Company mine site were approximately three times more effective in biodegrading manganese dioxide (34± 18 mg Mn++/1/day) than sixteen purified strains (11 ± 10 mg Mn++/1/day) isolated from the primary enrichment cultures. Two pure bacterial genera identified as a Pseudomonad and a Bacillus, with an excess MnOz and nutrient, were able to dissolve 106 mg Mn++/litre/day in mixed culture compared with 29 mg Mn++/litre/day when grown separately.

Jan 1, 1983

By H Han, W Wang, E Zhou, D Duan

"In this study, physical, chemical and microscopic characteristics of high phosphorus oolitic hematite were studied firstly. Based on which, the new methods of high phosphorus hematite used in the æsolid state reduction by rotary hearth furnace - magnetic separationÆ and iron nugget by rotary hearth furnace direct reduction processes were discussed. The results showed that high temperature, low basicity and high carbon content is conducive for the apatite in iron ore to reduce into molten iron, but not conducive to the removal of phosphorus. Through optimisation of process parameters, dephosphorisation rate of high phosphorus hematite is more than 60 per cent by æsolid state reduction roasting-magnetic separationÆ process while that is up to 80 per cent by iron nugget process. This study can provide theoretical and technical basis on economical and rational use of high phosphorus oolitic hematite.CITATION:Han, H, Duan, D, Zhou, E and Wang, W, 2013. New methods for high phosphorus oolitic hematite dephosphorisation by direct reduction process, in Proceedings Iron Ore 2013, pp 391-396 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 12, 2013

The Oregon-Idaho graben evolved after widespread tholeiitic flood basalt volcanism associated with the arrival of the plume head of the Yellowstone hotspot beneath southeastern Oregon approximately 17 - 16 Ma. The north- to north-northeast-trending, 50 km-wide graben evolved between 15.5 and 10.5 Ma during east-west extension. The graben is part of a middle Miocene back-arc rift (1100 km long) that includes the northern Nevada rift, the Baker and LaGrande grabens, and the Chief Joseph dike swarm of the Columbia River Basalt Group. The graben ceased to be a volcanotectonic depression as the cross-cutting western Snake River plain began to evolve at approximately 10.5 Ma. At about 14.3 Ma and continuing to approximately 12.6 Ma the Oregon-Idaho graben began to break up into subbasins that were bounded by intragraben fault zones. The break up was accompanied by a change to calc-alkaline volcanism that persisted within the Oregon-Idaho graben until 8.1 Ma, approximately 2.5 million years after subsidence within the graben ceased. Three intragraben fault zones have been identified and a fourth is inferred. The easternmost, the Devils Gate fault zone, coincides with the magmatic axis of the graben at approximately 14.3 Ma. By approximately 13.5 Ma the magmatic axis had shifted to the west along the Dry Creek Buttes and Wall Rock Ridge fault zones. A diffuse magmatic axis developed at approximately 12 Ma farther to the west where the fourth intragraben fault zone is inferred. In addition to serving as conduits for the ascent of basalt, basaltic andesite, rhyodacite, and rhyolite magmas, the zones focused the discharge of large geothermal systems. The intragraben fault zones display a common evolutionary pattern. The 2 to 3 km-wide zones initially control the distribution of facies in volcaniclastic sediments and the location of basalt hydrovolcanic vents. During this stage, the fault zones may have had no surface expression other than a low elevation change on a relatively low-relief landscape. As relief developed by continued deformation along the fault zones, strike-length of individual faults increased and weakly consolidated volcaniclastic sediments, silicified sediments and hot-spring sinter, and palagonite were eroded from the uplifted blocks and deposited in neighboring subbasins. It is during this stage that the large hot-spring precious-metals bearing prospects evolved. Displacements of over 150 m on a few faults within the zones and possible reversal of the sense of displacement along the zones occurred in this final stage of development. Locally, the fault zones were remobilised during the subsidence of the cross-cutting western Snake River plain. The intragraben fault zones within the Oregon-Idaho graben illustrate the relations among syntectonic volcanism and sedimentation and the evolution of geothermal systems within continental rift systems.

Jan 1, 1995

Up to 19 chemical parameters were studied in flotation pulps in six Australian lead-zinc concentrators with the aim of obtaining a better understanding of the nature of, and changes in, the chemical environment. This paperdiscusses collector residuals, metal concentrations in solution, and other parameters.Collectors used in the plants studied were various xanthates, Z-200, and Aerofloats. Xanthate residuals varied in different ways in most plants. However the general trend was for residuals to be at the O· 5-2 p.p.m. level in lead flotation and O· 5 p.p.m. or less in zinc flotation.Aerofloat residuals were also variable but in the plant concerned were at a much higher level (8-10 p.p.m.) than xanthate residuals. Z-200 residuals were in the 10-20 p.p.m. range and it was found that the Z-200 added to zinc flotation was reporting in dam return water and entering lead flotation.Copper concentrations in solution were negligibly low in those plants where cyanide was not used. When cyanide was used, copper was at the 5-20 p.p.m. level and appeared to be present as Cu(CN)-2. However the hiocyanatepresent may be important. Xanthate was also present in these solutions.Zinc concentrations ranged from 0·1 to 800 p.p.m. in different plants. The general trend was for the zinc level to be highest in the grinding circuit and to drop during flotation. However there was always an increase in zinc concentration when copper sulphate was added, even tho.ugh this incre.ase was not permanent, and the increase was greater with higher copper sulphate additions.The manganese concentration also increased appreciably during copper-activation of marmatite. In some plants lead concentrations increased from 0·1 to 1 p.p.m. during activation of marmatite.Calcium concentrations (20-1200 p.p.m.) and magnesium concentrations (10-600 p.p.m.) tended to be fairly stable in each circuit.

Jan 1, 1970

By T Isaksson, J Anderson

The procurement process for underground construction contracts, in particular those contacts involving tunnel boring machines (TBMs), is subject to many complex and inter-related variables, including national and local politics, public policy, community involvement and media attention û as well as strict environmental and legal requirements. Other restrictions include the time available to adequately investigate geotechnical conditions and viable technical options to determine the best construction methodologies û including selection of tunnel boring machine characteristics and, those construction means and methods suitable for the specific geotechnical and environmental conditions. The latter are, most often, quite imperfectly understood. æGetting it rightÆ implies that an optimal configuration û of machine type, characteristics and associated methodologies û can be found and successfully implemented for a particular project. æFrom the beginningÆ implies that the lack of time issue can be successfully resolved. Within an international context this paper highlights a number of issues of concern which relate to tunnel procurement systems and the ways in which certain key processes are managed during planning, design and construction. The authors argue that there is considerable room for improvement in the way tunnelling projects are undertaken and an approach is discussed which has the potential for substantial gains in cost and schedule and reduction of risk. Savings, however, may only be fully realised if the new methods can be fully implemented by all parties involved. This, we believe, will require the rejection of ætraditionalÆ forms of management and procurement with associated changes in the roles and responsibilities of owner, engineer and contractor. Additionally, risk identification, assessment and mitigation are essential cost and schedule control process which have, to this point, been underutilised by the underground construction industry.

Jan 1, 1999

Jan 1, 2004

By A Brzovic, E Córdova

In an underground mine, different mining activities such as undercutting and cave progression generate redistribution in the present in situ stress field, and these changes are represented in the rock mass through induced seismicity.In order to study and analyse the induced seismicity generated in El Teniente, a block model was developed to account for the dissipated seismic energy through different areas of the mine from 1992 to 2015. More than 2.1 million seismic events were unified and classified in 3D in order to be used for the interpolations. The resultant model variables account for the accumulated energy releases in a monthly time resolution, and provide the ability to intersect different 3D entities with the stored information in the blocks, and estimate the energy evolution inside these entities.The generated model was used to analyse the geotechnical variables that determine the seismic response for the rock mass in the mine, such as geometry and direction of advance of the undercut fronts, lithological domains, and to study the ‘work’ the rock mass needed to go through in order to generate caving in areas with different stress settings.A specific area of the mine under high-stress conditions was analysed by studying the seismic energy associated with two subsidence caves interacting around the project, the modelled lithology. Using the same approach two adjacent projects are analysed to understand the released energy from the rock mass based on different stress and geotechnical settings for each project.CITATION:Córdova, E, Brzovic, A and González, R, 2016. Analysis of progressive seismicity and its correlation with geotechnical variables at the El Teniente Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 835–844 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

Despite a long history of production of industrial minerals and rocks, New South Wales still offers significant opportunities for exploration for and development of these minerals. Exploration for opal, sapphires, and zeolites in the State has been particularly encouraged by pioneering geological studies by the Department of Minerals and Energy, which have resulted in the development of important new geological concepts and exploration techniques. Large areas with potential for these minerals have not yet been tested. In the case of sapphires, the studies have identified a new type of deposit which is'the source of most of the sapphires mined from alluvial deposits. Recent price increases for heavy minerals, a re-evaluation of previous exploration in coastal regions, and a recognition of suitable environments in inland New South Wales have stimulated renewed exploration both onshore and offshore and have led to increased production. Significant potential also exists for development of a number of other minerals, including: topaz, which occurs in large, unusual and perhaps unique deposits in northern New South Wales; dimension stone (particularly granite); bentonite; diatomite; and silica for metallurgical use. Potential also exists for development of construction material resources, particularly construction sand, which is in short supply in the Sydney region.

Jan 1, 1989

By D O’Dea, B Godel, T Honeyands, B Ellis, T Harvey

X-ray computed tomography (XCT) is a non-destructive technique that allows the exploration of the internal structure of solid objects in 3D. Over the past ten years, the combination of XCT with more conventional 2D techniques and quantitative 3D image processing and analysis (commonly referred to as digital rocks) has allowed us to address some of the most challenging problems in ore deposit studies. The range of X-ray energies used in XCT allows the X-rays to be transmitted through complex and dense materials including iron ores (eg sinters, lumps, granules). Recent high-resolution XCT scanners have the ability to generate multiscale (25 down to 0.3 µm voxel size) imaging of a given sample enabling the characterisation of 3D textures across a range of scales. This paper will focus on the application of digital rocks to iron ore sinter particles (using filtered polychromatic X-ray beam). The paper is divided into three parts and includes: i) details on the methodologies including their benefits and limitations and the effect of spatial resolution; (ii) the quantification of pore network topology and pore characteristics (eg open versus closed pores, pore size distribution and pore morphologies; degree of connectivity of the pore network and its tortuosity); and (iii) the evaluation of the technique to characterise various phases within the material and quantify 3D mineral textures.CITATION:Godel, B, Ellis, B, O’Dea, D, Honeyands, T and Harvey, T, 2017. Digital rocks for iron ore sinters – towards a D quantification of sinter textures, in Proceedings Iron Ore 2017, pp 529–534 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By D Reid, J Black

The adverse health impacts from diesel particulate matter (DPM) exposure are a well-known global concern. The building evidence has triggered underground mining operations to review existing atmospheric conditions and assess the scale of the challenge faced. South32’s Cannington Mine (Cannington) evaluated the ability to provide a healthy atmosphere from a whole mine approach, taking into account existing preventative controls including: maintenance strategies, fuel quality, mining operations, ventilation provisions, monitoring protocols and effective education and training programs.During the evaluation process, Cannington gave due recognition to the advice and guidance provided in the Queensland Guidance Note 21 (QGN21), the Guidelines of New South Wales’ MDG29 and Mining Industry Advisory Committee (MIAC) of Western Australia. Each of these documents advises a dilution rate of >0.06 m3/s/kW is best for reduction of DPM exposure in underground mines.Achieving the prescribed mine ventilation rate typically results in the need to directly invest significant capital into increasing ventilation infrastructure in order to further dilute contaminants. In today’s economic market of volatile metal prices and increasing pressures to meet regulatory requirements, it can become challenging for established metalliferous operations to create a balance between optimisation of current ventilation infrastructure and capital outlay.In order to obtain and correctly justify the requirements for capital investiture Cannington conducted a ventilation operational analysis for the life-of-operation, identifying the existing air volume envelope was adequate for current and future production rates by optimising existing primary ventilation infrastructure through the implementation of a modified ventilation on demand (VoD) and air conservation system.This process achieved sustainable operating and capital cost reductions without compromising delivery of adequate ventilation to work areas. The process also recognised that engaging mine workers’ ownership of their work areas is crucial to maintaining a technically efficient and operationally robust ventilation system.This paper will concentrate on Cannington’s existing preventative controls, their implementation and their management for the prevention of increased DPM exposure; reducing the risk of both short and long-term health impacts to ‘as low as reasonably achievable’ (ALARA).CITATION:Black, J and Reid, D, 2017. Delivering a healthy atmosphere underground in a cost-conscious environment, in Proceedings Australian Mine Vent Conference 2017, pp 159–168 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

I am wearing two hats today. When the invitations went out to participate in this forum, two were received in the head office of the Department of Lands and Survey - one addressed to the Director-General of Lands and one to the Chairman of the National Parks Authority. It seemed logical that as the department is responsible to the Government for the administration of the National Parks Act 1952, we should respond by providing one speaker to cover both the department's interests and those of the National Parks Authority. I hope, however, that this will not blur the clear distinction which exists in the context of the mineral industry between Crown land on the one hand administered by the department for the statutory Land Settlement Board and national parks and allied reserves on the other hand which are the responsibility of the National Parks Authority.

Jan 1, 1976

Declining metal prices over the last few years have reduced the number of new metallurgical plants being built and limited opportunities for introducing new processes. However, technological advances are still being made. With increasing economic pressures, the emphasis is now on reducing unit costs by making equipment larger and through use of technologies with lower operating costs. This trend can be seen in the increasing size of grinding mills and flotation cells used in recent plant designs and in the adoption of HPGR crushing as an alternative to SAG milling. Few new technologies achieve widespread introduction until there are clear economic or operational drivers. These might currently include: ò          increasingly stringent environmental standards; ò          availability of exotic materials for equipment construction; ò          increasingly sophisticated instrumentation and control systems; ò          the need to treat increasingly refractory oretypes; and ò          the length of supply routes to many new plants. As a result of these drivers, a number of new and revitalised technologies will get increasing prominence in the design of new operations, such as: ò          use of ultrafine milling equipment such as MIM's Isamill for treatment of refractory gold ore concentrates; ò          use of thiourea as an alternative for cyanide in sensitive locations; ò          novel hydrometallurgical routes for treating base metal ores in remote locations; ò          paste thickening for tailings deposition; and intensive cyanidation of gravity concentrate

Jan 1, 2000

By P Atkinson, M P. Simpson, J R. Kyle

BM37 is a bonanza-grade (>30 ppm Au) ore shoot of the Maria Lode of the Karangahake adularia-sericite epithermal deposit in the southern Hauraki Goldfield. Samples from BM37 contain up to weight percent gold. The ore shoot is a vein that pinches and swells, but is typically tens of cm thick, and locally exceeds 0.5 m in true width. Gold occurs as irregular anhedral electrum grains that range up to 300 microns across and contain 38 to 59 wt per cent Au (ave. 52 wt per cent Au). Electrum occurs in sulphide-rich bands in association with pyrite, chalcopyrite, acanthite, galena, sphalerite, and local covellite. Lower grade samples contain local to rare mckinstryite [(Ag, Cu) 2S] and polybasite [(Ag, Cu) 16 (As, Sb) 2S11]. Pyrite from BM37 is nearly stoichiometric; it lacks the As that commonly occurs at up to percent levels in pyrite from other veins in the goldfield. Acanthite also contains low quantities of trace metals, and typically has less than 2.5 per cent Se. The vein shows complex textures. Bonanza grade sulphide-rich ginguro bands form discrete layers adjacent to the vein margins, and occur as breccia fragments encased by later massive to comb quartz with local quartz after platy calcite. Both the breccia fragments and ginguro bands are cross-cut by later quartz veins. Textures thus indicate that formation of the high-grade portions of BM37 resulted from one or more discrete events that differed markedly from the events that formed the bulk of the vein.

Jan 1, 2006

Process Simulation and Plant Design of a Mineral Selective Magnetising Flash Roasting Plant Using Neutrons

Sep 13, 2010

Triboelectrostatic Producing Ultra-Clean Coal

Sep 13, 2010

By A T. Job, M L. Edgar, P R. McAree

Characterising ores in-pit and in real-time presents a significant value opportunity for the mining industry. Hyperspectral imaging systems are proposed as an enabling technology to achieve this real-time characterisation. This paper considers the application of a hyperspectral imaging spectrometer mounted on a shovel. We define the performance requirements for such a spectrometer and associated subsystems during a typical dig-load cycle. The relatively high swing rotation speed of the shovel requires approximately video-rate exposure times to achieve good spatial resolution. We analyse a selection of components against these requirements and find that suitable commercial spectrometers, detectors and optics appear fit-for-purpose. Automated, real-time spectral classification systems are also available, with only relatively modest requirements for processing power. The paper argues that at near peak solar illumination, a system for field deployment at the required sensitivity is viable using only commercial off-the-shelf components.CITATION:Job, A T, Edgar, M L and McAree, P R, 2017. Real-time shovel-mounted coal or ore sensing, in Proceedings Iron Ore 2017, pp 397–406 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

Adsorption of Starch on Kaolinite Surfaces

Sep 13, 2010

Applicaton of Agricultural Residues from Pyrolysis in Flotation of Black Coal

Sep 13, 2010

The oxidation of ferrous sulphate to ferric sulphate with air and oxygen in a gas lift percolator was investigated with initial Fe2+ concentrations in the range 0·01 M to 1·0 M,temperatures in the range 20-80°C, and pH in the range oto 2.The rate of formation of Fe3+ was found to be well described by the rate expressionEquation 1and a consistent mechanism is proposed.The presence of Cu2+ was found to cause an increased rate of oxidation, the effect being greater with Cu2+ concentrations increasing in the range 0·001 M - 0·01 M in 0·2 M Fe2+. The effect of other solutes containing Ni, Zn, Mn, Co, Hg, Cl, Mo, NH4, As, Cr, or Na at a concentration of 0·001 M in 0·2 M Fe2+ was negligible.

Jan 1, 1972