Search Documents

A drive, 3,500 ft long, was planned to explore mineralization exposed by diamond drilling. A rate of advance of 150 ft per fortnight, approximately double previous Broken Hill rates, was required. Subsequent to the completion of this drive its extension for a further 6,200 ft was planned to provide a main haulage way along which ore could be transported from a newly acquired lease back to the main hoisting shaft, a total distance of 13,500 ft.This paper describes the working conditions, relationships, manning and costs, and gives details of the cycle and equipment used to achieve rates up to 170 ft per fortnight.OBJECTIVEDiamond drilling from the 1,000 ft level at the Delprat Shaft section had indicated that the zone of mineralization, about 150 ft wide, which had been explored on the 1,000 ft level for a length of 2,600 ft, continued downwards with a westerly dip. The drilling results showed that within this wide zone there were arrower lenses of mineralization of possibly payable grade (see composite plan, Fig. 1).Diamond drill holes of 2,000 ft and over, particularly through heavily sheared areas of sericite schist, had been found to be costly, slow, and inadequate in testing the potential and trends of these smaller concentrations of mineralization.It was therefore decided that an exploratory drive should be advanced from the northern limit of the 1,480 ft level into the western mineralization, and that from this drive diamond drill holes should be drilled at dose intervals to outline the ore.The 1,480 ft level was chosen for the following reasons.1. It had the greatest northerly reach of the accessible levels at No. 7 Shaft section below the 1,000 ft horizon and therefore would enable the test to be made most quickly.

Jan 1, 1965

With the proving of a mineable orebody at Orlando in May 1961, Peko Mines N.L. was faced with the decision of whether to mill the ore on site or to haul it 25 miles to central facilities at Peko. Orlando was a relatively small orebody, so that it was decided to haul, although no reliable assessment of possible ore haulage costs was available.The necessity for a good haul road was recognised from the beginning and a 17 mile, 12 ft wide, single seal bitumen road was constructed, to link the mine to the Stuart Highway and Peko. The initial selection of 20 ton capacity diesel-powered end-tipping ore carts was made, with the best information available at the time.Since then some 130,000 tons of ore have been carted over a period of 3 years, and this paper presents the experiences of this haulage operation and the lessons learned.A second mine has just been brought into operation at Ivanhoe, 19 miles from Peko. For this haul it was decided to use an ore haulage vehicle of the side tipping road train type, which would cart some 70 tons, or more than three times the load of the vehicles initially selected.Only about 5,000 tons had been hauled at the date of this paper, but preliminary figures indicate a cost 01 1· 65d./ton-mile as against 2·47d. for the smaller vehicles.It would appear that the road haulage of ore from small outlying mines to a central plant can be highly economical, if certain basic rules concerning haul roads and vehicle selection are followed. This paper does not try to determine the maximum tonnages and haul distances which would finally make road hauling uneconomical...

Jan 1, 1966

By G Veillette, B Parker, S Hart

This paper provides a history of the challenges that were experienced while treating both the clayey oxide gold ores and the supergene copper-gold ores at the Boddington Gold Mine during the period 1989 to 2001. However the bigger challenge was to find a process flow sheet that would allow the economic treatment of the large low-grade competent gold-copper resource that underlies the oxide and supergene gold resource. Metallurgical test work and engineering studies on this resource started in the mid 1990s and culminated in the approval in 2006 of the 35 Mtpa Boddington Expansion Project to treat this material. The process flow sheet provides the basis of an energy efficient comminution circuit that includes high pressure grinding rolls and a treatment circuit with gravity separation, flash and conventional flotation to produce a precious metal low-grade copper concentrate followed by cyanide leaching of the rougher-scavenger and cleaner tailings streams. The treatment circuit allows maximum removal of copper minerals prior to cyanide leaching and so provides an environmentally responsible tailings disposal circuit.

Jan 1, 2007

By Moorrees C, Koh P. T, Tsambourakis G

Calcination of samples from the Savage River region of Thsmania containing varying magnesite/dolomite ratios under conditions optimized for the magnesite component, followed by carbonic acid leaching at elevated pressures, leads to leachates of varying composition. For a 3 per cent solids slurry leached at 15.5°C and 700 k Pa carbon dioxide, the leachates have magnesium concentrations in the range 0.71 - 13.2 g/litre. The corresponding magnesium extraction data are 12.5 - 86.4 per cent. The variation in leachate composition would be unacceptable in terms of continuous processing, so that a feed of "constant" composition is essential. Selective mining and physical beneficiation to remove the bulk of the dolomite do not appear to be practical. It is concluded that the most appropriate method of feed preparation is to carry out extensive blending of the magnesite/dolomite ore and the resultant calcine.

Jan 1, 1987

The mining industry is the largest source of foreign income for South Africa. It is also the main source of employment in the country and, as an industry; it is also one of the largest. Due to the labour-intensive nature of the industry, labour costs in South African mines make up nearly 50 per cent of the total mine cost. It is thus imperative to have optimum labour planning and labour management systems in place.The focus of this study was to investigate current underground labour-planning models. It is shown that there are serious limitations. The range between an oversupply and undersupply of labour can be as high as ten per cent. A new system was therefore developed to ensure a constant labour demand and supply on a daily basis. One of the main objectives was to determine the existing labour supply range and thus the requirements to fill the undersupply. For this purpose, a specific methodology was designed to capture and process all the relevant information. Mine personnel was involved throughout the entire process to ensure ownership of the new model. This buy-in was achieved through planning workshops, interactive presentations and discussions. The improved frequency of daily blasts validated the new system by providing the correct amount and mix of the labour force. The new labour-planning model was then extended to optimise revenue. Implementation on a mine resulted in increased income of R95 million.

Dec 6, 2010

This paper sets out to discuss how alluvials - particularly mineral sands, tin and gold have adjusted to meet the problems of lower grade and more difficult physical political and economic conditions. The mineral sands industry seems to have adapted satisfactorily but less so with tin and gold.

Jan 1, 1996

A tectonic interpretation of the Coromandel Peninsula which suggests that the basement underwent tensional collapse at its northern and southern ends would permit more ready penetration of late stage magmatic fluids. This hypothesis is consistent with regional trends of the chloride content of low grade geothermal waters and of the yield of gold and silver per unit weight of quartz worked. The consequences of such a model are that mercury should not only be a good pathfinder for Coromandel gold, but that it should be correlative with ratios of base metals high in the zoning or paragenetic sequences to those lower in the sequences. This is demonstrated successfully in an area of mineralisation in the southern Coromandel.

Jan 1, 1987

By G J. Lyman, F S. Bourgeois

As the prices of metals slide, financial control of mineral processing operations becomes more and more important. Control of a mineral processing operation implies measurement of grades, recoveries and losses, with every effort being made to recover more product from the same feed. Shareholders become more concerned with the transparency of the operations and the corporate governance.There is only one way to achieve this and this is by sampling and making good use of the results of that sampling. Sampling systems that provide only 'rough' figures are not good enough. Similarly, a competitive position in the marketplace demands close control of product quality. Maximisation of product output demands that the product just meet the specification so that product yield is maximised. Decisions based on precise sampling results carry less risk that those based on imprecise results.This paper reports some recent advances in sampling theory that permit full quantification of sampling distributions, not just the sampling variance as has been possible in the past. These advances can be used together with simulation methods to tie down sampling precisions and develop calculations that quantify decision making risk when using the sampling results. A number of examples illustrate the use of the new advances and a final example indicates the development of risk analysis curves in the coupling of sampling precision to sale of a commodity.CITATION:Lyman, G J and Bourgeois, F S, 2015. Sampling, corporate governance and risk analysis, in Proceedings MetPlant 2015, pp 27–34 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

Biosorption of Cr(VI), Pb(II) and Zn(II) from Aqueous Solutions by Immobilised Phanerochaete chrysosporium Biomass in a Fixed-Bed Column The continuous-flow adsorption of Cr(VI), Pb(II) and Zn(II) from aqueous solution by immobilised Phanerochaete chrysosporium biomass in a fixed-bed column was studied. The effects of flow rate, influent concentration of Cr(VI), Pb(II) and Zn(II) and bed depth on breakthrough curves and biosorption capacity were investigated. The experimental results showed that the breakthrough time decreased with increasing flow rate, increasing influent concentration and decreasing bed depth. The data also indicated that the equilibrium uptake of Cr(VI), Pb(II) and Zn(II) increased with decreasing flow rate and increasing influent concentration of Cr(VI), Pb(II) and Zn(II). Two models were employed to predict the breakthrough curves and to determine the characteristic parameters of the column useful for column design. The Thomas model was able to predict the breakthrough curve in the range of relative concentration(Co/Ci) higher than0.3, Cr(VI), Pb(II) and Zn(II) whereas the validity of the Bohart-Admas model was limited to the initial part of breakthrough curve at all flow rates and influent concentrations of Cr(VI), Pb(II) and Zn(II). The feasibility of reusing the immobilised fungal beads through five adsorption/desorption cycles in fixed-bed column was investigated.

Sep 13, 2010

Investigation of the Classification Operation in a Coal Pulverising Vertical Spindle Mill Coal pulverisation in power plants is a major electrical energy consumer. In 2006 more than 41 per cent of world electricity generation was from coal where pulverisers use 0.5 to 1 per cent of gross generation. Therefore, pulverisers are an important target for optimisation not only for reducing costs of power generation but also for reduction of greenhouse gas emissions. A better understanding of the operation of pulverisers is an essential requirement for their optimisation. However, little information is available, other than operating experience, on the performance of pulverisers and how these react to changes in operational variables. This study investigates the effect of changes in coal and airflow feed rates on the classification performance that occurs in an industrial scale ball-and-race vertical spindle mill in which the pulverisation and classification processes are linked together due to the separator classifier being an integral component within the pulveriser. In order to decouple the breakage and classification processes, samples were cut from upward flowing streams through sampling ports drilled on the pulveriser body at different locations. Specific sampling tools were developed. Samples collected from the pulveriser were size and density fractioned to distinguish the differences in behaviour of the components, namely coal and mineral matter. The coal flow rates on dry basis within the mill and around the separator classifier were calculated by mass balancing the multi-component data. The difference in classification behaviour of components during pneumatic transport was confirmed. The response of the circulating load in the mill (~600 to ~1100 per cent) as well as the dependency of fineness of the streams to the operating variables was demonstrated. The approach taken in this study has proved that development of a classification model for a vertical spindle mill pulverising non-homogeneous materials, eg coal, requires treating these materials as multi-component/composite substances.

Sep 13, 2010

The importance of timbering, not only from a financial point of view but from an actual mining point of view, is so often overlooked or slightly glossed over by the average expert and investor, that I have thought it would prove interesting to go into the matter and to invite discussion upon the subject. We will first take small veins, or reefs as they are termed in some mining countries; and by small veins it is intended to denote fissures from a few inches to three feet. The ore body is supposed to be confined within well defined walls free from gangue matter, unless the casing can be defined as such. Now, if the walls are smooth and moderately hard, no timbering is required other than the stulls, which are braced from wall to wall in order to form platforms or stages to stope from. Should the reef from wall to wall prove payable, or should the vein be of a character to prohibit cleaning or sorting; and it be determined to send the whole of the stone to the, reduction works, the stuUs should be left in place until the section or block of ground is worked out, in order that if a weak spot in the walls (especially the hanging) occur, it would be possible, without any particularly extra expense or difficulty often times accompanied by danger to brace and secure the slabs. After the block became entirely stoped, it would pay where labour was cheap to remove the majority of timbers to stull another section.

Jan 1, 1901

IF a straight line should be drawn on the map (See 1, page 96) through the northern half of the South Island of New Zealand, from Mt. Domett in the north to Arthur's Pass in the south, and another line drawn parallel to it and at a distance of ten miles to the west, according to the topographic scale, it will be found that within the belt thus drawn across the country all the most important mines, past and present, of the South Island are situated, with the exception of a few in Otago.The most important product of this tract being gold, and Reefton, the most important southern mining field, being situated at about its central portion, the zone may aptly be termed "The Great Reefton Gold Belt." The occurrence of so many gold mines along this particular strip of country is not at all a matter of chance, but is the outcome of cause and effect. Running along the eastern side of the gold belt are the Brunner and Victoria Ranges, which are chiefly composed of crystalline schists and metamorphic granite of probably Cambrian or Silurian age; between these and the gold-bearing series there are interposed at one or two places some beds of slates, limestones, and...

Jan 1, 1910

THE most important part of the routine survey work on a mine is the keeping up-to-date of plans and sections showing progress of stoping and development work, and the direction of the latter for the purpose of making necessary connections. Except in specialcircumstances, e.g., major horizoittal development, the exactitude required in this work is not extreme, and a method of survey in keeping with the demands of the work itself is all tbat is required.For example, no one would consider measuring the walls of a stope to a fraction of an inch; such extreme accuracy would be wasted.The stope walls being irregular, a mean is usually taken, and for ordinary purposes a survey with a limiting error of six inches is quite satisfactory for the purpose of plotting either stoping or development.It is the author's aim in this paper to describe the method in use at the North Broken Hill Oompany's British mine. This method, while being sufficiently accurate for the purpose in view, possesses the very great advantages of speed and simplicity of operation,with a minimum of necessary equipment. This latter is a very important item where several surveys on different levels have to be carried out on the one day.Let it be understood, however, that the use of this method does not dispense with the theodolite, but simply serves as a convenient adjunct to obtain details and to extend the accurate theodolite survey up rises and down winzes, and through ladderways orwinzes into stopes, where the use of a theodolite, if not actually impossible, is often exceedingly inconvenient. This is particularly so on the British mine, where a large proportion of the ore is won from narrow and complex-dipping lodes, and where vertical ore...

Jan 1, 1928

Mineral exploration and mining in New Zealand has had almost five years of new legislation. The requirement for different consents is a challenging, time consuming, expensive exercise but in most cases the new procedure is working, although the matter of obtaining access to land is still a major issue. Priority is critical. After lodgment of an application for a minerals permit there are many other matters to address such as identifying land owners, occupiers and administrators, preparation of access applications, consultation and preparation of various resource consent applications.

Jan 1, 1996

The Martha Hill project operates with a nett surplus of water, due to the catchment of rainwater on the tailings dam and the requirement to de-water the open pit mine. It is necessary to discharge this surplus, treated as required, to the Ohinemuri River which flows past the process plant.   The treatment plant, adjacent to the process plant, handles all effluent from the Martha Hill operation including water pumped from the mine, excess water from the tailings decant, and seepage from the tailings dam underdrains. To-date the plant has treated and discharged over 800 000 tonnes of water.

Jan 1, 1991

Analyses of scheelite from all the known scheelite fields in the South Island of New Zealand have shown that the scheelites are essentially molybdenum-free. The scheelites are almost stoichiometric CaWO4, except for some strontium replacing the calcium, with a maximum of 0·92 per cent SrO. Variation in strontium content appears to be' related to the metamorphic grade of the enclosing rocks.

Jan 1, 1970

By H M. Ahmed, W S. Dunbar

Construction of cave mining systems requires significant capital expenditure and long-term commitment of human, equipment and material resources before production commences. Risks and uncertainties of these large-scale mining projects are significantly higher than for small-scale projects. This is due to the complexity and interactions of the construction schedule components and the large scale and uniqueness of such projects. One way to successfully manage construction uncertainties that would lead to schedule delays is to include a reasonable cost contingency in the budget estimation. A real options approach based on the least-squares Monte Carlo (LSM) method is used to estimate cost contingency associated with schedule uncertainty in mass mining projects. Cost contingency is estimated as the cost of potential project crashing (acceleration) decisions, which pays for not extending the schedule. While such a significant undertaking is expected to be subject to some delays, these can have an enormous impact on the economic value of such projects. The value of the crashing option was explicitly formalised into the process of valuation, as it is assumed to be a single option being considered in the valuation at every decision point prior to the construction completion date. As a part of the proposed method, a stochastic function for the percentage of remaining scope of work for the remaining duration of the entire project was integrated into a framework of numerical simulations. This ensured that this function can implicitly account for sources of schedule uncertainties for projects represented by multiple and overlapping work packages. The LSM method was applied to a real case scenario in an operating block cave mine, with modified scale and features. The results yielded by the LSM method indicated that significant changes in capital budget allocation stem from variation in a contractor’s risk perception and confidence level of estimated delays.CITATION:Ahmed, H M and Dunbar, W S, 2016. Budget estimation and contingency allocation of block cave construction using least-squares Monte Carlo real options, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 801–808 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By N Clarke, G R. Ballantyne, M S. Powell, P Elms, A Anyimadu

AngloGold Ashanti Ltd nominated Sunrise Dam Gold Mine as a case study via their involvement with the long-running Australian Mineral Industry Research Association (AMIRA) International P9P research program (AMIRA, 2015) . A group of researchers from the Global Comminution Collaborative (GCC) conducted a comminution circuit survey and review together with a large group of graduate metallurgists, senior metallurgists and operators. Fundamental and applied research understanding was used to identify productivity and efficiency improvements around the crushing and grinding circuits. The limitations of current scientific knowledge were identified through this process and this will allow future research to be more focussed on what is required by industry.The comminution circuit at Sunrise Dam comprises three stages of crushing followed by two stages of ball milling. The secondary crusher and primary ball mill classification were identified as the primary limitations of the circuit. The secondary crusher was found to be underperforming through overall equipment efficiency (OEE) analysis and an improved chamber design was identified by Chalmers University. This improved design will promote higher power utilisation, choke feeding and a finer crushed product for the milling circuit. The primary ball mill product is classified by a combination of a trommel, 3 sieve bends and a hydrocyclone. The combination of poor classification and coarse, competent feed led to a situation where the primary mill was overfilled with rocks, reducing grinding rate due to cushioning of impact. Size specific energy (SSE) benchmarking methodology was used to identify that a 10% increase in throughput could be achieved with improved primary classification.CITATION:Ballantyne, G R, Clarke, N, Elms, P, Anyimadu, A and Powell, M S, 2015. Application of research principles to identify process improvement at Sunrise Dam Gold Mine, in Proceedings MetPlant 2015, pp 221–229 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By K H. Esbensen

The Theory of Sampling (TOS) has made remarkable strides and has witnessed a suite of achievements over its ~65-year history; especially in the last 15 years, since organised work began for the erstwhile fragmented sampling community (2003). Theory and practice have been very well exposed and disseminated, as witnessed in the successful series of the World Conference on Sampling and Blending (WCSB) events and other dedicated sampling and mining conferences in Australia and South Africa. At this WCSB8 occasion we fittingly devote a section of our conference to celebrate the life and monumental achievement of Pierre Gy, the originator of the Theory of Sampling; a special issue of TOS Forum was recently published to the same purpose. But TOS is most emphatically not a finished work.Here I try to look into the future with a personal view: TOS – what’s next? Commensurate with this objective there is offered some out-of-the-box thinking. The purpose is to try to zoom in on probable additional future aspects of TOS and its application compared to the first 15 years of our common journey. There are bound to be lacunae here-and-there across the vast application horizon delineated, which is as it should be, as this lecture is meant to initiate a broad(er) debate – and readers may agree with all, parts, or none of the topics presented. All is well that furthers this debate.CITATION:Esbensen, K H, 2017. Theory of Sampling – what’s next?, in Proceedings Eighth World Conference on Sampling and Blending , pp 29–38 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By C Jia, J Graindorge, L M. Olssen

Picking up abandoned mining tenements and looking to recover remnant resources around old operations is an opportunity that comes with its own challenges and risks. Reliance on information released to government departments (such as the Department of Mines and Petroleum (DMP) in Western Australia) by the previous owners, can compound the risk.This paper explores Alto Metals Ltd’s Lord Nelson and Lord Henry deposits and surrounds near the town of Sandstone in Western Australia. The Lord Nelson and Lord Henry open pits produced around 2 Mt of ore for over 250 koz of gold during production between 1999 and 2010. There has been no further work carried out in the area between 2010 and 2016. The deposits are open at depth and along strike.Alto Metals picked up the tenements in 2016 and has subsequently re-estimated remnant resources around Lord Nelson and Lord Henry, and publicly reported updated Mineral Resources in accordance with the JORC Code 2012.All of the information was manually compiled from data released to the DMP and annual reports. This paper highlights the challenges and risks arising from this data compilation, geological interpretation, re-estimation and classification process, together with future opportunities and challenges for further developing the area.CITATION:Olssen, L M, Graindorge, J and Jia, C, 2017. Starting from scratch – defining remnant resources from publicly available data: a case study from the Lord Nelson and Lord Henry gold deposits, in Proceedings Tenth International Mining Geology Conference 2017, pp 175–188 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017