Search Documents

By S. Harries Daddow

IN order to get an idea as to the strength of steel rails, it will be well to review the tests to which iron rails have been subjected. In England, Mr. Ashcroft found that the best 80 pound rails broke under a 300 pound weight, falling 15 feet. In Germany the Society of Railway tyfanage1-s determined 011 and have long applied a test of 1000 pounds falling 101/2 feet, as the standard which all first-class iron rails must reach. In this country no inspection nor test is applied, but tests made show that iron rails fro; our most reliable makers, break under a G foot fall of a 1500 pound drop as an extreme test, most of those tested breaking under a far less test; some breaking with less than a 3 foot fall of the same weight. Everywhere where steel has been used, engineers have come to the conclusion that some test is required to show the regularity and strength of the product. As compared with iron, the tests which steel will stand are wonderful. After numerous experiments partially based on the experience of the rail-mill at Graz, belonging to the Southern Railway of Austria, the Society of German Railway Managers fixed upon a test of 2000 pounds falling 138 feet. They found that this test represented the steel which suited their necessities, and also found that with steel of otherwise average purity, this test represented about one-half per cent. of carbon, and made it a rule to take no steel containing under three-tenths of a per cent. of carbon, because it was too soft. They expressed a hope that a harder steel could soon be made tough enough to stand the same test. I n England, a test was adopted of 2240 pounds, falling 15 to 17 feet on the rail on heavy bearings. This test has been found satisfactory under heavy traffic on average road-beds, and has been invariablyPILLAR of coal, which are designed and left in our mines as the means of supporting the overlying strata of our coal-beds, and securing protection to the miner, are not only insufficient for these purposes, but the most objectionable means of providing the desired security to life and property. Though such pillars are left at a great sacrifice to the owners of collieries and mineral lands, loss to the resources of the commonwealth, and ultimate privation to the public, they defeat the very ends for which they are designed, and not only do not secure life and property, but are as fatal to the one as ruinous to the other. Propositions.-It is eminently desirable that the resources of the Common wealth-particularly our mineral wealth in anthracite coal, which is limited-should be carefully utilized and made available, not only to ourselves but our posterity. Yet, speaking as an anthracite miner, we are wasting our resources of coal with a recklessness which will bring ruin in the end, unless checked, not only to the iron manufacturing interests of the East, whose chief protection, in competition with the iron-masters of the interior, lies in a cheap and abundant supply of anthracite furnace fuel, but to the best interests of the State. It is, consequently, not only desirable, but necessary, that we should realize every ton of coal from each colliery, and every acre of coal area, in order that our resources may not be wasted at present, to breed want in the future, and to realize the greatest present benefit to the mine, the miner, and the public. It is not possible, however, to secure these ends, if we continue to leave, as we do at present, from one-third to one-half our resources in anthracite as pillars in our mines. But our sad bills of mortality, our abandoned collieries, and our yawning mountain-sides, present ample evidence that even this enormous waste of coal, though left for the purpose of protecting life and property, is as totally inade-

By J. Gordon Parr, D. H. Polonis

The formation and subsequent decomposition of metastable phases in Ti-Ni alloys containing up to 11 pet (atomic) Ni have been studied. The decomposition of a completely retained ß phase and of a completely transformed 8 phase in a 6 pet alloy has been followed by X-ray diffraction and metallographic methods and by hardness determinations made during the process. The possible mechanisms of the reactions are discussed. PREVIOUS investigations of the Ti-Ni system have usually been limited to phase diagram studies; but little attention has been given to metastable phases and tempering processes. These are important, however, since equilibrium conditions are rarely achieved—nor, perhaps, are they desired—in practice. Up to the present time the available transformation data for titanium alloys appear to be restricted to isothermal transformation curves for selected binary and ternary systems. No quantitative studies have been made of the mechanism by which equilibrium is approached. Several independent investigations have been carried out to determine the Ti-Ni phase diagram. Early work by Wallbaum' and later by Long et al.' produced tentative phase diagrams which were not representative of true binary conditions, since the alloys were contaminated with oxygen and nitrogen. The most recent diagram (Fig. 1) is due to Margolin et al.," and a slight modification of the a + ß/ß boundary (shown dotted) has been proposed by McQuillan.' The structure of the phase Ti,Ni was shown by Duwez and Taylor" to be face-centered-cubic, with 96 atoms per structure cell. The formation of a martensitic ß phase (close-packed-hexagonal) in Ti-Ni alloys has generally been observed when specimens of low nickel content are rapidly cooled from the 0 (body-centered-cubic) range. Margolin et al. reported an increasing tendency for P to be retained in lump specimens as the nickel content increases. McQuillan' has studied the effect on the microstructure of delay time in quenching, and has reported the formation of pro- eutectoid a precipitate in a quenched hypoeutectoid alloy. In a previous study of Ti-Fe alloys," experiments were made on powder specimens produced by filing alloy ingots. Techniques were devised for the preparation and heat treatment of alloys, and X-ray diffraction methods were used both for structure determinations and phase ratio estimations. A similar approach has been made in this study of Ti-Ni alloys. Experimental Methods Ten alloys ranging from 0.25 pet to 18 pet Ni* * All compositions are in atomic percentages unless otherwise stated. were prepared from iodide titanium bar stock (hardness Rf 72) and Johnson-Matthey spectrographic standard nickel by levitation melting.' As a check

Jan 1, 1957

By John H. Hollomon

The interpretation of notched-bar impact results has been a matter of controversy since the introduction of more or less standard tests by Fremont,' Charpy2 and others at the turn of the century. Many investigators3-l1 have contributed to the understanding of the significance of such tests. Several symposiums12,13 have been held with the express purpose of discussing the significance and interpretation of the impact tests. It is not the purpose of this paper to review all these contributions to the development of the knowledge on this subject, but rather to present an interpretation of notched-bar impact tests that appears to be in agreement with the available published data. Fundamentally, the interpretation discussed in this paper of the brittle failure of some steels in notched-bar impact test is similar to the qualitative analysis presented by Ludwik3 in the I92o's. Essentially, Ludwik stated that the function of the notch was to increase the tensile stress necessary for yielding, and that brittle failure occurred when the stress necessary for yielding exceeded the normal stress required for fracture (with no plastic deformation). Ludwik, however, had no means of measuring this normal stress necessary for failure of a plastically* undeformed metal, therefore he could not extend his interpretation beyond the qualitative stage. Kuntze14 and recently Mc-Adam15 attempted to determine the effect of deformation on the stress necessary for fracture by testing, in tension, specimens notched to various depths and angles. Because of the uncertainties in Kuntze's (and McAdam's) analysis of the stresses (which have been pointed out by Sachs16) and the inherent nonuniformity in the stress distribution in notched bars, the results of such investigations are difficult to interpret. A more direct method of measuring the effect of deformation on the fracture stress was suggested in previous papers"-18 and has been utilized in the present investigation. The present paper concerns itself primarily with the behavior of notched impact specimens. The effects of strain rate, temperature, and stress distribution, which are discussed with reference to the impact specimen, apply just as well to the behavior of metal at the bases of notches in any engineering structure. All that is necessary is to determine the stress distribution in the structure at the base of the notches.

Jan 1, 1944

By J. W. H. Clare

An equilibrium isotherm at 550°C is given for ternary alloys rich in aluminum containing 0 to 15 wt pct Cr and 0 to 20 wt pct Mn. Phases encountered are: aluminum solid solution; stable temary compound G; and MnAl8,. In addition, a limited number of alloys were annealed at 450°C to check for differences from the 550°C isotherm. These experiments limited the composition of the G phase at 550°C and further experiments established that the G Dhase is not stable above 590 ± 1 °C. RAYNOR and Little1 established several equilibrium isotherms using aluminum-rich alloys containing up to 5 pct of the elements chromium and manganese. These isotherms showed that, in addition to an a solid solution and the two binary intermediate compounds 8 and MnAl6, a stable ternary compound ex-isted in the system. This phase was called the G phase because of its ghostly appearance in micro-sections. Little, Raynor, and Hume-Rothery2 found a similar phase in binary aluminum-manganese alloys and, as a result of their experiments, concluded that the G phase was a metastable phase existing in the aluminum-manganese system. This phase was stabilized by the addition of chromium. The constitutional work of Raynor and Little,' although showing the existence of the G phase in the aluminum-chromium-manganese system, did not establish precisely the composition limits of the phase or the temperature above which the phase became unstable and disappeared from the system. The work described in this paper was undertaken to provide this information. An examination of the previous work' showed that an isotherm at 550°C would provide the required data regarding composition in the shortest possible time, as the (a + G) phase field narrows considerably at higher temperatures. The same work showed that the G phase ceased to exist between 580° and 595°C. A more precise estimate of the transformation temperature would therefore be obtained by annealing selected alloys at successively higher temperatures beginning at 580°C. EXPERIMENTAL PROCEDURE 1) Materials Used—The experimental alloys were prepared from four master alloys containing 15.00 w pct Cr, 15.28 wt pct Cr, 19.80 wt pct Mn, and 19.38 wt pct Mn which were made from super-purity aluminum, electrolytic chromium, and electrolytic manganese. The aluminum was of 99.996 pct purity, the principal impurities being copper, iron, and silicon. The chromium and manganese were 99.9 pct pure, the principal impurities being antimony, calcium, and magnesium. 2) Preparation of the Experimental Alloys—The alloys were prepared in 20-g quantities by melting together the requisite amounts of master alloy and aluminum in an alumina-lined crucible and, after thorough stirring with an alumina rod, cast into a cold copper mold to give ingots 1/4 in. in diam and 3 in. in length.

Jan 1, 1960

By T. Egleston

The necessity of using a refractory material capable of much greater resistance to chemical action and having a far higher melting-point than those which contain silica, which melt and sweat off in the furnace even when not exposed to bases forming with silica more or less fusible compounds, has led to a careful practical study of all those materials which contain very refractory bases. The results of these researches, extending over several years, and made on a very large scale in many of the largest works in Europe, are of the highest interest, not only considered as a step in the progress of the study of the materials themselves, but in the application of refractory materials to metallurgical uses in general. The result of the experience of the last seven years with these basic materials, as in general with all such substanccs, is that natural products cannot be used as such. They are either too uncertain in their quality, contain substances which may in certain cases be very injurious, or, when in a condition in which they might be used, are so rare as to become practically unavailable for employment on a large scale. The materials that may he used are therefore not only limited in number. but they must be prepared artificially. When the use of basic artificial material is further extended, no doubt the number of these substances will not only be greatly increased, but the methods of preparation will be both perfected and cheapened to such an extent as to permit their application in processes for which they have hitherto proved too expensive. The quantity of refractory materials required for making ingots will he from 130 to 150 Ibs. per ton, or between 6 and 8 per cent. of the metal produced. In an establishment producing 2000 to 3000 tons of steel per week, considerable space is required to handle the basic materials properly. It is proposed in this paper to briefly discuss these basic materials and their application in the only two metallurgical processes where they have as yet been applied. These are the basic Bessemer and the basic open-hearth process, known as the Thomas-Gilchrist processes.

Jan 1, 1886

By Kurt Kennedy

A method is described by which three elements can be condensed simirltaneously on a common substrate in such a way that the composition varies with position on the substrate. Almost all possible combinations of three solid elements can be formed in a single evaporation. The three elements are heated by magnetically deflected electron beams. The alloys and cornpounds formed by this method generally correspond to those trade by other methods; however, many exceptions exist. Simple symmetric crystallographic phases tend to form in preference to more complex phases. The Nb-Sn. Cr-Fe-Nt, and other systems of alloys made by this method will be discussed. Phases that form very slowly, such as the o phase in Cr-Fe alloys, may be formed rapidly by this method when certain substrate temperatures are used. STUDYING all the mixtures and compounds of two or more elements by the preparation of individual samples forces the investigator to make sampling sufficiently close together so that the properties of the intermediate compositions can be inferred. A completely unknown system will require a dis c our aging ly large number of preparations in order to fully know all its properties. For the purpose of expediting this type of investigation, methods have been devised to prepare samples that have a continuous variation in composition over some predefined area. The code-position of two elements onto suitable substrates has been used to produce alloys or compounds that have variable compositions depending on their positions on the substrates Composition gradients have been formed by depositing a wedge-shaped layer of one element and then depositing a second wedge-shaped layer on top of it such that the total film thickness is kept constant. Concentration equilibrium perpendicular to the surface is then established by annealing.4 This paper describes a method for the simultaneous condensation of three volatile components on a substrate such that there is a regular variation of composition with position on the substrate. The arrangement of the evaporation sources and the substrate is shown schematically in Fig. 1. Materials to be evaporated are placed in three water-cooled crucibles located at the corners of a 10-in. equilateral triangle. Electron beams from cathodes located below the crucibles are bent 180 deg by magnetic fields and focused on the material to be evaporated. The cathodes are connected in parallel to a constant-current 12-kv power supply. The distribution of emission current from each cathode is controlled by filament temperature. When materials that sublime are to be evaporated, the electron beam is deflected by an auxiliary ac magnetic field so that the beam moves over the surface of the evaporating material rather than digging a hole in one spot. The substrate is a 10-in. triangle of 2-mil stainless steel or molybdenum which is stretched against a slightly curved heat sink by a frame as shown in Fig. 2. This frame and heat sink are located so that each corner is directly above an evaporation source. The heat sink has three radiant heaters at each corner that can be separately controlled permitting the

Jan 1, 1967

By C. P. Lawhon, J. P. Simpson, W. M. Evans

Recent efforts to design drilling fluids for increased drifting rates have confirmed some laboratory results of other investigators, but have also produced additional data that should be considered. These data were obtained under controlled test conditions using a microbit drilling machine. Clays and some polymers have previously been reported to cause reduction in drilling rate. Recent data have shown that under laboratory conditions, suspensions of a single day or polymer have sometimes given faster drilling rates than when water was used. Measurements have been made of clay suspensions and polymer suspensions comparing filtration (I) under API conditions, (2) while drilling with temperature of 150F and differential pressure of 1,000 psi and (3) under dynamic conditions after drilling. Some correlation between instanraneous filtration (white drilling) and drilling rate has been observed. INTRODUCTION Several papers have been presented that related drilling fluids to penetration rate. Generally, it was found that a decrease in the solids concentration resulted in significant increases in the drilling rate. Of course, this change also resulted in a decrease in the viscosity of the drilling fluid.' Conclusions from investigations by this laboratory are in agreement. Data have shown that of the simple mud measurements commonly made at the drilling rig (density, plastic viscosity. yield point, API filtrate and total solids), only the density and total solids have a significant relationship to the drilling rate in Berea sandstone when attempting to correlate a single mud property individually.' More recent drilling rate experiments have been designed to study (1) effects of individual clays and polymers on drilling rates in Berea sandstone and Lueders limestone, (2) the relationship between drilling rate and dynamic filtration as measured after drilling and (3) the relationship between drilling rate and dynamic filtration as measured during drilling. Data show that drilling rates are dependent upon type and concentration of particles, type of formation and filtration of the individual fluids while drilling. Mud pressure: pressure of drilling fluid as measured after leaving the drilling chamber (Fig. 1). This is taken to be approximately the mud pressure just past the bit and at the face of the formation. Terrastatic pressure: pressure representing weight of overburden. Formation pressure: pressure of formation fluid as measured at outlet of drilling chamber (Fig. 1). This is taken to be approximately the pressure of fluid in the interstices of the formation. Differential pressure: difference between the mud pressure and formation pressure. LABORATORY EQUIPMENT AND TESTING PROCEDURE The drilling equipment was described in two previous publications."' Main components are a drilling chamber, filter-heater, rotary drive and variable-speed circulating pump. Auxiliary pumps supply pressure boosts for the mud, terrastatic and formation pressures. All equipment is designed for 15,000 psi and 500F. Capacity of the circulating system is approximately 7 gal. The mechanical design was facilitated by moving the rock down onto the bit. Data collected with this design should not differ from that obtained by a normal design where the bit moves into the rock. Drilling fluid is pumped through 50 ft of ID pipe coiled in an oil bath, enters the rotary shaft at a right angle and is pumped through the jets on the bit (Fig. 1). Most of the drilled solids are extracted by a screen mounted in the circulating system on the suction side of the pump. Data reported in this paper were obtained by controlling these parameters: mud pressure, 5,000 psi; formation pressure, 4,000 psi; terrastatic pressure, 5,000 psi; force on bit, 1,000 Ib; formation, Berea sandstone and Lueders limestone; flow rate, 7 gal/rnin; bit, 11/4-in. diameter with two 0.078-in jets; mud temperature. 150F; and rotary speed, 60 rpm. Mud pressure was controlled at 5,000 psi, thus giving a differential pressure of 1,000 psi even though the fluid densities varied. Cores of 3%;-in. diameter and 8 in. long were selected from quarry blocks to provide some control of grain size distribution, permeability and porosity. A 2-in. section was cut off each core and a I -in. diameter plug was taken from this section. Permeability to 5 percent by weight sodium chloride solution was determined and the large cores were

By R. E. Zimmerman

The separation of fine sizes of coal from its impurities by means of various flotation methods has become of increasing importance in the coal industry. This, no doubt, will be even more so in the future as the quantity of high grade coal is depleted, particularly that used for metallurgical purposes. The purpose of this paper is to describe and report the results of research work done under the auspices of the Pittsburgh Coal Co. to determine the amenability of their bituminous fine sizes of coal to flotation, to investigate the value of various reagents and factors affecting their use, and compare the results between froth flotation and bulk oil flotation. Compared with the preferential flotation of complex minerals, or ores, the flotation of coal is comparatively easy. However, this statement should not lull one into the feeling that there are no special problems involved. For instance, the separation of coal from pyrite in high sulphur coals is still far from being 100 pet successful. Size consist has considerable effect on reagent consumption and recovery. Other factors will be described and finally it must be remembered that in the flotation of coal a low priced material is being treated and thus economic considerations govern more closely its application than is generally the case in treating other minerals. As a result of the research work done by the Pittsburgh Coal Co. on the flotation of coal, it was concluded that it was practical to clean the —48-mesh coal commercially by froth flotation and after several different types of flotation units and circuits were investigated by means of pilot plants, large scale units were installed at their Champion Nos. 1, 4 and 5 Preparation Plants for the cleaning of —48-mesh slurries. These large scale operations have been recently described by D. H. Davis.' C. P. Proctor and C. B. Carlson2 in their chapter on Froth Flotation of Coal in the AIME Seeley W. Mudd series book on Coal Preparation describe some of the practical applications of our Pittsburgh Coal Co. laboratory work in actual plant practice as well as summarizing part of the investiga-tional work. The author presents this paper, however, as a supplement to their reports, and records the basic research accomplished in the laboratory investiga-tional work as well as the results of experiments using bulk oil flotation. In presenting this work the author wishes to state much more work must be done in applying the principles of flotation to cleaning coal, especially in view of recent studies and practices in other mineral beneficiation fields. Methods of Conducting Laboratory Tests The bulk of the research work was conducted in the laboratory of the Champion No. I Preparation Plant. This plant has elaborate facilities for sampling and analyzing coal and proved to be an admirable location for the investigational work. Four types of laboratory flotation ma-

Jan 1, 1949

By W. D. Kruger

Methods for analyzing flooding or cycling projects by means of two-dimensional flow calculations are presented in the literature. The use of these methods allows the determination of optimum operating conditions for such projects and provides information on pattern efficiencies, relative flow rates, pressure distributions and floodout histories. The accuracy of such analyses depends on the basic reservoir data employed, especially the absolute permeability distribution in the reservoir; however, absolute permeability data normally are determined from well flow tests and/or core measurements and are so limited in quantity and quality that they do not adequately describe the reservoir flow properties. A calculation procedure is presented for determining the areal permeability distribution in the reservoir. Use of the procedure allows verification of the basic reservoir data through the matching of past reservoir conditions, thereby providing proper data for reliable predictions of future operations. The calculation procedure is a numerical technique based on a mathematical model of the reservoir and is designed for solution by means of an electronic digital computer. Results from field application of this procedure are presented. Permeability distributions from measured data are compared to those calculated to indicate the need for the analysis. Comparisons of field-measured and calculated pressure distributions are given to establish the validity of the calculation procedure. The conclusions of this paper are (I) use of the calculation provides data that allow a match of past reservoir conditions and thus reliable prediction of future operations; and (2) the procedure should, where applicable, be used to provide adequate reservoir data for use in two-dimensional flow calculations and related reservoir analyses. INTRODUCTION One means of providing more precise engineering control over reservoir operations during all stages of depletion is to develop some type of model to simulate the reservoir, using information developed from the behavior of the prototype to predict the performance of the actual reservoir. The use of mathematical rather than physical models for this purpose has been gaining in importance recently because of the application and availability of electronic computers. Mathematical models avoid instrumentation difficulties and allow easier handling of large-scale problems. At present, analyses employing two-dimensional models are common, and thought is being given to the use of models in three dimensions. The use of multi-dimensional models is necessary to show not only what is occurring in the reservoir, but also where in the reservoir the phenomena of interest are taking place. Methods for analyzing flooding or cycling projects by means of two-dimensional numerical models are presented in the literature. The use of these methods allows the determination of optimum operating conditions for such projects and provides information on pattern efficiencies, relative flow rates, pressure distributions and floodout histories. The applicability of numerical models and the results of using such analyses have been presented through field examples. The references indicated here discuss fully the data necessary to build the mathematical reservoir model and the way the model is used to study or predict the future performance of the reservoir. The accuracy of the analysis of such projects depends on the basic reservoir data employed in the construction of. the model. In order to be sure the model represents the reservoir, it must be used to match some known set of reservoir conditions, i.e., to match past reservoir performance. The accuracy of the model is directly dependent upon the absolute permeability distribution in the reservoir; however, absolute permeability data are normally determined from well flow tests and/or core measurements, and are so limited in quantity and quality that they do not adequately describe the reservoir flow properties. There is always the need for better data and for verification of existing data. The purpose of this paper is to show the use of the mathematical model to match past performance in flooding or cycling projects, the use of numerical techniques to adjust the basic absolute permeability data if necessary so that a match is obtained, and in this way to generate the effective areal permeability distribution of the reservoir. A review of the basic concepts of the numerical model will be given, followed by a discussion of the data-adjusting technique for matching past performance. TWO field examples will be cited to show

By P. G. Winchell, J. K. Jackson

The strtcture of body-centered Fe-Ni-C alloys (0 to 16.5 wt pct Ni) containing less than 0.015 wt pct C was investigated by measuring the carbon-diffusion peak at low frequencies with a torsion pendulurrr. By determining the Snoek damping in ferrite and in quenched alloys of identical composition, the effects of nickel content and heat treatment were separated, and the existence of a structure in which Snoek damping is greatly reduced was revealed in the quenched ternary alloys. The relative amount of this structure increases with increased nickel content and cooling rate. It is proposed that this structure may be highly imperfect or tetragonal. In Fe-Ni-C alloys containing only ferrite the addition of nickel (0 to 5.1 wt pet) decreases tke area of the carbon-diffusion peak and shifts its position to lower temperatures but broadens the peak only slightljl. The decrease in peak area with increasing nickel implies that short-range interactions with the nickel atoms prevent some of the carbon atoms from participating in the relaxation process. The shift in the peak position indicates a long-range effect of nickel on the movement of carbon atoms so that at 300°K the diffisivity of carbon in -ferrite is increased by about 35 pct by the addition of 5.1 tut pct Ni. The results are presented as distributions of relaxation strength 072 the activation energy under the assumption that the frequency factor is invariant. BODY-CENTERED iron-base solid solutions dissolve carbon interstitially in the octahedral sites. The occupation of an octahedral site produces a tetragonal distortion of the surrounding lattice. These sites fall into three sets according to the orientation of the tegragonal distortion associated with each and may be identified by their lattice coordinates as: type 1/2 0 0, type 0 1/2 0, type 0 0 1/2. At low carbon levels in cubic ferrite the carbon atoms are distributed at random1 among these sites. In high-carbon body-centered iron-base solid solutions, which are unstable with respect to several two-phase mixtures, a tetragonal structure occurs as the product of the diffusionless transformation of austenite. This transformation is commonly accompanied by appreciable microstrain and its product is called martensite. The tetragonality of martensite, a supersaturated solution of carbon in a iron, is maintained prior to decomposition even though local diffusion of carbon occurs as evidenced by carbide precipitation. The tetragonality is taken as evidence that one set of octahedral sites is preferentially occupied by carbon. (This preferential occupation is called ordering below.) Support for this view is presented by the absence of strain-induced carbon-atom diffusion in high-carbon solid solutions (martensite). Such diffusion occurs in ferrite and produces the 40°C internal-friction peak observed at 1 cps frequencies.' Thus, there appears to be qualitative evidence favoring the view that at sufficiently high carbon levels tetragonality arises spontaneously as a result of the ordering of the carbon atoms; however, no experimental evidence exists concerning an equilibrium between cubic and tetragonal body-centered solid solutions. Moreover, attempts to estimate the energy of ordering7-' predict a value too low to maintain the tetragonality observed at medium carbon levels, 0.3 to 0.6 wt pct C. In the present work an attempt using internal-friction measurements is made to establish the presence or absence of tetragonality in low-carbon body-centered solid solutions formed by quenching austenite. Fe-Ni alloys containing about 0.01 wt pct and 0 to 15 wt pct Ni were selected for the study. While the work was in progress Gilbert and Owen10 reported that the transformation which occurs in these alloys during quenching at rates up to 5000°C per sec is not martensitic but is more properly categorized as massive. Thus, the solid solution

Jan 1, 1964

By Ancel St. John

During a session on coal and coke at the February, 1926, meeting of the American Institute of Mining and Metallurgical Engineers, the writer called attention to the important work on the X-ray analysis of coal1,2 being carried on in England by C. Norman Kemp and his associates. This aroused so much interest that a paper on the subject was requested for the October meeting. It has seemed advisable to make this paper a preliminary survey of the present status in the application of X-ray methods to coal problems and to follow it from time to time with further articles as the art develops. A survey of this sort naturally divides itself into two parts, radio-scopic analysis of the distribution of constituents through the body of the coal, and diffraction analysis of the state of association of the elementary components. In this article the subject matter concerning radioscopic analysis has been drawn almost entirely from the writings of Kemp and his associates and the illustrations have been sptcially furnished by him. It is a pleasure to record here a great indebtedness for this courtesy and cooperation. The subject matter and illustrations concerning diffraction analysis are taken from the author's unpublished researches. Nature and Properties of X-rays Before proceeding it is well to recall the nature and some of the properties of X-rays, as well as our present conception of atomic structure According to the accepted theory atoms are composed of electrically-charged particles. A positively-charged center, called the nucleus,

Jan 1, 1927

By Robert L. Akre

When Marco Polo visited China in the 13th century, no one knew what black powder was except the Chinese; they knew enough to make dazzling fireworks with it. But the realization that black powder could also do useful work came much later and, like all important discoveries, it altered the course of history. It was in the 14th century that black powder was first used to break rock in a very crude way; there were no drills and the powder was simply poured into cracks and exploded by setting it afire. Because its energy value was pretty low, the need for something more powerful was felt when the industrial revolution began. In the 1850s, miners began experimenting with liquid nitroglycerine on a limited scale. This was a very sensitive and dangerous explosive. Fortunately in the 1860s, Alfred Nobel succeeded in stabilizing nitroglycerine by absorbing it in kieselguhr-and a new product, dynamite, was born. With it, miners were able to unleash the great energy of nitroglycerine for blasting purposes. But dynamite was still a very sensitive explosive. In subsequent years, other explosives of various strengths and characteristics were developed, such as blasting gelatin, gelatin dynamite, ammonia dynamites, (all containing some nitroglycerine or nitrostarch), and liquid oxygen explosives. These products and their variations supplied the blasting trade for many years. A grained ammonium nitrate product containing some carbonaceous material entered the market in the 1930s. This explosive had below-zero sensitivity-meaning: a No. 6 blasting cap imbedded in it would not detonate it. A more sensitive initiator, called a primer, was needed to detonate this mixture. From Rags to Primacord to Solid-State The first initiator for an explosive charge was probably a rag slowly burning its way to the charge; this method was quite unreliable. Then came the burning fuse, which was an improvement. Next was the nonelectric blasting cap initiated by a fuse. With these initiators, a miner needed quick reflexes and good legs; upon lighting the fuse, he had to run immediately for cover. Development of the electric blasting cap that allowed for accurate timing eliminated this hazard; the electric cap, however, introduced other safety problems because of its susceptibility to extraneous electricity, e.g., ground currents, lightning, and static electricity. These caps also became available in millisecond delays. Development in the mid-1930s of Primacord, a detonating fuse insensitive to electrical currents or impact, further reduced blasting hazards, and is generally acknowledged as the safest known means of initiation. Eventually, Primacord millisecond connectors also became available for delay patterns in blasting. In the mid-1960s, the Primadet delay was introduced; it is a practical nonelectric detonator system that offers the precise timing of electric blasting caps-and is immune to the hazards or effects of extraneous electricity. Recently, Research Energy of Ohio, Inc. introduced a new type of solid-state blasting machine that combines a sequential timer and delay caps. It enables the efficient breakage of rock with a minimum amount of shock, ground vibration, and noise. Improvements in Blast-Hole Drilling World War II created an enormous demand for coal and other minerals in the U.S. and elsewhere. Great efforts and large amounts of capital were spent to find new mineral deposits and develop better mining methods. But while mechanization in mining proceeded at a rapid pace particularly in open-cut work, there was a definite lag in developing new or improved machines for drilling blast holes. The industry continued to depend largely on horizontal, churn, and pneumatic drills. No better machine was available for large scale production. The need for improvement in this phase of mining became more acute in the post-war years. Despite efforts toward further mechanization, mining costs rose rapidly because of mounting inflation and increasingly high wages. In most operations, drilling and blasting the overburden became the principal item of cost. Therefore, whatever size holes were being drilled, the holes had to be spaced so that any foot of the bore hole could be loaded with the maximum load required for the number of cubic yards of material that each foot of the hole was carrying. With the smaller holes that were being drilled, the proportion of drilling cost to the total drilling and shooting cost was much higher than it would have been with larger holes (because of the closer spacing required by smal-

Jan 1, 1977

By Charles S. Barrett

Metallurgists are making use of the stereographic projection to a steadily increasing extent. In the last five years no less than 20 papers in American metallurgical journals alone have employed the stereographic projection; recent books on physical metallurgy, plastic deformation, X-rays and their applications, and crystal structure use it. Mineralogists have used the stereographic projection for many years in the description of symmetry classes and crystal planes, for it presents an accurate, easily understood plot of any angular relations in crystals with all unessential features eliminated (such as the accidentally determined size and shape of crystal faces). In metallography and physical metallurgy the projection is much used for the analysis of markings appearing on polished grains: slip lines, twins, cracks, structures formed by precipitation, magnetic-powder patterns, etch pits, etc. Data from certain types of X-ray photograms are most conveniently analyzed by its use, particularly those for determining the orientation of single crystals or the preferred orientation of grains in an aggregate. Calculations of how to tilt or cut a crystal parallel to a certain crystallographic plane or to reflect X-rays from a certain plane are rapidly carried out. It has been adopted almost universally to the exclusion of other methods by those studying the deformation of metallic crystals, save where the accuracy required is greater than a few tenths of a degree. Any directional property in a crystal or polycrystalline material can be shown on a stereographic projection; for example, the modulus of elasticity, yield point, etc. It has been repeatedly called to our attention that there is need of an elementary explanation of the principles and methods of stereographic projection, covering all the common applications in the field of metallography and physical metallurgy. The following contribution is an attempt to fill this need. The description of each method is supplemented with references to publications in which the method has been used. For convenience to the reader, these illustrative references are chiefly in American journals, particularly the publications of the American Institute of Mining and

Jan 1, 1937

By Chester A. Rowland

INTRODUCTION Comminution is generally a feed preparation step for subsequent processing stages; exceptions being when a final product such as aggregates, specification sand, Portland Cement, and similar products is produced. Grinding, the fine product phase of comminution, requires a large capital investment and frequently is the area of maximum usage of power and wear resistant materials. Grinding is most frequently done in rotating drums utilizing loose grinding media, lifted by the rotation of the drum, to break the ores in various combinations of impact, attrition and abrasion to produce the specified product. Grinding media can be the ore itself (autogenous grinding -- primary and secondary), natural or manufactured non-metallic media (pebble milling) or manufactured metallic media -- steel rods, steel or iron balls. This chapter will discuss general mill design and the specific design and application of the following types of tumbling grinding mills. [Overflow Rod Mills Figure 1 Peripheral Discharge Rod Mills Figures 2 and 3 Compartment Mills Rod and Ball Figure 6 Ball Figure 6a Pebble Mill Figure 6b Overflow Ball Mills Figure 8 Diaphragm (Grate Discharge) Ball Mills Figure 9] I. GENERAL MILL DESIGN A. Liners The interior surface of grinding mills exposed to grinding media and/or the material being ground are protected from wear and corrosion by rubber, metallic, a combination of rubber and metallic, or non-metallic wear resistant materials. B. Drives Economics at the time of plant design and mill purchase determine the drive to be used. The simplest drive is the low speed synchronous motor with speeds in the range of 150 to 250 RPM connected to the mill pinion-shaft by either an air clutch or flexible coupling.

Jan 1, 1982

By W. C. Knopf, I. M. LeBaron

In the Carlsbad area potash is dry-mined and wet-concentrated. Wet concentration involves recircu-lation of saturated brines, with resultant difficulties of brine disposal and inherent losses in recovery through solution of the KCl. A dry beneficiation process for potash minerals would offer many advantages over present methods. International Minerals & Chemical Corp. has been working on development of a dry process for some time. This article is a progress report. Potash ores available in this country are largely mixtures of halite and sylvite contaminated with slimes and often with many sulfate and magnesium minerals. Electrostatic concentration of KCl when the contaminating minerals are in low percentage has been accomplished. Continuous production of better than 60 pct K2O concentrate from high potassium sulfate ores has not been demonstrated at the present time. Laboratory Procedure: Laboratory work on electrostatic beneficiation of potash minerals has been carried out using both pure crystals and mined ore. Electrostatic separation of the two main components of potash ore, sylvite (KCl) and halite (NaCl), is accomplished by first heat-treating the ore to allow for electric charging of the particles. Preferential exchange of' electrical charges between different mineral particles through surface contact is the principal mechanism involved. After proper conditioning of the particle surfaces, the oppositely charged minerals are dropped vertically into a horizontal electric field having a field gradient from about 5000 to 15,000 v per in. The particles are free-falling in the field. A suitable power supply is used to produce the proper total voltage for the electric field. Total required voltage is, of course, a function of electrode spacing. A typical electrode arrangement with power supply is shown in Fig. 1. In general, the total voltage on any system is 75,000 to 90,000 v. Power consumption is negligible, as leakage at insulators and corona discharge are the main losses in the system. Optimum preheat temperatures for pure material components generally are not the same as for mined minerals. Fig. 2 shows clearly that maximum recovery on a 50 pct pure KCl, 50 pct pure NaCl mixture occurs at a preheat temperature of about 600°F. In this test the preheat mixture was allowed to cool to about 225°F before dropping through the electric field. The optimum temperature for sep- aration is practically never the optimum temperature of preheat. Optimum separation for mined Carlsbad potash ores occurs when a preheat temperature closer to 900°F is used, as shown by Fig. 3, which plots percent sylvite (KCl) in the concentrate and tails as a function of preheat temperatures. Here again the ore was allowed to cool to about 225°F before separation. It should be noted that efficiency of separation increases continuously with increasing preheat temperatures until incipient fusion of the ore takes place at about 950°F. The increase in optimum preheat temperature for Carlsbad ores over the pure minerals can be traced to the effect of the clay slimes intimately associated with the mined potash. If the slimes associated with the ore are removed by washing with alcohol or other non-aqueous material, the necessity of preheating to the high temperature is removed. This temperature range has been proved critical within these limits during continuous pilot plant operation. Concentrate and tailings grade and optimum recovery also are functions of the temperature of the potash mineral particles during separation in the electric field. Fig. 4 presents data indicating that feed to the rougher pass should range between 150°F and 275°F for best results. It has been found by subsequent pilot plant work that these temperatures can be maintained in actual operation.

Jan 1, 1959

By L. L. Oriard

In order to predict the influence of blasting on slopes, one must first understand the action of explosives, the manner in which rock is broken or displaced, and how seismic waves are transmitted, and the nature of these seismic waves. In this paper, the author describes the action of high explosives on rock masses, beginning at the source of the explosion, extending through the zone of rupture to a distance where only elastic waves of low energy persist. The paper describes the relationships between explosives charge quantities and distances, including the character and intensity of the seismic waves in various types of terrain. In looking at the analysis of slopes subjected to seismic waves, it has been common practice to assume a simplified model in which the anticipated acceleration is applied horizontally to the slope as an equivalent static force, or a model in which there is a rigid base subjected to mechanical shaking. Such models do not accurately portray blasting activity taking place within or near the slope in question. In dealing with blasting effects, it is important to under- stand seismic wave types, wave lengths, attenuation and transmission paths, as well as vibration intensity. In most cases, those slopes that are the least stable under static loading will also be the least stable under dynamic loading, although there may be rare exceptions. Thus, the more that is known about a slope statically, the better will be the assessment of it dynamically.

Jan 1, 1983

By J. L. Taylor, P. Duwez

The phase boundaries in the ternary system Ti-Cr-Al have been established at 1800° and 1400°F for alloys containing more than 60 pct Ti. The martensite transformation temperature has been measured for the titanium-rich alloys. THE studies of binary alloys of titanium with the transition elements which have been published so far1-0 ndicate clearly that the solubility of these elements is always much greater in the high temperature body-centered cubic form of titanium (ß phase) than in the low temperature hexagonal form. In this category of alloying elements are iron, nickel, chromium, manganese, vanadium, molybdenum, tungsten, columbium, and tantalum. Although studies of the nontransition elements have been rather limited, early work on titanium binary alloys'" has shown that most of them were not very soluble in the a form, with the exception of aluminum, for which the solubility in a is about 25 pct.13, 12 In addition to this large solubility in a, aluminum is also soluble in ß titanium to the extent of about 35 pct and the transformation temperature from ß to a is raised with aluminum content. This effect is also typical of aluminum, in contrast with that found for the transition elements which lower the ß to a transformation temperature. Therefore, it may be anticipated that tprnarv titanium alloys with aluminum and any one of the transition elements will constitute a class of ternary alloys having characteristic features absent in alloys involving two transition elements. Chromium was chosen as a typical transition element for the present study because ternary alloys of Ti-Al-Cr commercially produced have been found to possess very interesting physical properties (MST-3 pct A1-5 pct Cr of Mallory-Sharon).'" Binary Systems The binary systems Ti-A1 and Ti-Cr have been established recently by several investigators. The data used in this investigation were taken from the complete diagram of Bumps, Kessler, and Hansen." This diagram agrees quite well with earlier investigations." For the Ti-Cr system, the phase boundaries at 1800" and 1400°F were taken from refs. 6 and 7. The binary system Cr-A1 has been studied recently by Bradley." This system is rather complex and contains not less than seven intermediate phases. The present study was limited to the titanium corner of the ternary system (less than a total of 40 pct Cr plus Al) and none of the phases present in the Cr-A1 binary alloys were found in the ternary alloys investigated. Experimental Technique Microscopic observation and X-ray diffraction measurements were used to identify phases and de-

Jan 1, 1954

By R. Woodward Moore

A graphical method of analyzing the data obtained from shallow earth-resistivity depth tests is presented. The method is based upon empirical results and has no theoretical basis. The usual apparent resistivity-electrode spacing curve is used together with a cumulative resistivity-electrode spacing curve plotted on the same sheet. The greatly reduced scale required for plotting the cumulative values of resistivity together with the effect of the summation of the individual resistivity values serves to minimize the effect of purely local surface anomalies and inadvertent errors of measurement. The point of intersection of tangents or straight lines drawn to intersect at zones of maximum curvature in the cumulative curve indicates the depth to the underlying material. Numerous figures are presented in which data from published reports and from recent field studies are analyzed and the results compared with actual depths established by borings or with depth values obtained by the use of theoretical methods of analysis. Smoothly rounded curves of apparent resistivity such as are often obtained in the field, and which have been a serious drawback to attempts to analyze the data empirically heretofore, appear to be susceptible to rather accurate analysis by the method described. The method is best suited to analyses involving shallow two-layer formations. It has been applied successfully, however, in analyzing the data obtained from tests made over shallow three-layer formations. As with most empirical methods, its chief advantage is its simplicity and ease of application. There have been published many papers that discuss the interpretation of data obtained from earth-resistivity tests when using the four-terminal method of electrode spacing developed by Wenner.' The majority of these have dealt with theoretical analyses for two-layer and three-layer formations. Some sets of "master curves" have been presented for use in analyzing field data to determine the depth to the first and possibly the second horizon below the earth's surface. Although practically all of these theoretical methods of analysis have appeared to have particular merit and some have been used successfully in practice, they have been found to be of little value where the local conditions surrounding the test failed to conform to those assumed in the theory. In certain fields, particularly in civil engineering, relatively shallow explorations are often involved and geophysical methods of test must compete with the direct methods of exploration ordinarily used. Only when it can be demonstrated that geophysical methods of test can materially reduce the time and cost of a given exploration project will the civil engineer abandon direct methods in favor of the interpretations of geophysical exploration data. Empirical methods of analyzing earth-resistivity data have been used in many instances in the past. Such methods have been employed for a number of years by the Public Roads Administration in research work relative to the application of

Jan 1, 1946

By F. R. Zachar

IT has always been understood, in northern West Virginia where both the Pittsburgh and Sewickley seams are mined, that pillaring or splitting in the lower Pittsburgh seam could break the interval strata and make mining in the overlying Sewickley difficult or impossible. In some instances, however, mining methods practiced in the overlying Sewickley have reversed the problem, resulting in a shifting of the intermediate layer and destroying valuable acreages of the Pittsburgh seam below. The Pittsburgh seam in this area is, on the average, 102 in. thick. About 18 in. of low-quality head coal are left for roof protection as it is mined. Immediately over the coal are two draw slates, two rider 'seams, and a good hard black shale, locally called black rock, which serves as a permanent roof where draw slates and riders are taken down on certain main haulroads. In most areas mined in this seam in the past the bottom has been satisfactory but soft. However, in areas now being mined by the Christopher Coal Co. in Monongalia County the bottom is very hard and unyielding. The Sewickley seam, lying 85 ft above the Pittsburgh, will average nearly 70 in. in thickness and is overlain by massive shales and sandstones. Much of the seam is mined only down to the "sheep skin," a hard band about 4 in. above the bottom, which is composed of relatively hard shale. Fig. 1 shows a typical cross-section through the Pittsburgh and Sewickley seams in the area being discussed. The thin Redstone seam is not deep-mined but is stripped in some locations where it outcrops. Most of the Sewickley seam in the Morgantown areas has been mined out from 10 to 30 years. There are at present only two large mines and five or six others of small production operating in that seam. Mining systems in the past were generally of the room and pillar type with some full pillar extraction. This seam in the Scott's Run area was operated by as many as thirty or forty different companies at one time, during an era beset with strikes, market failures, and depressions. Most of the barrier pillars along the many main haulroads were abandoned, and blocks of Sewickley coal that would be fully recovered with today's machinery were left unmined when conditions became anything less than favorable. Consequently the mined-out Sewickley is spotted throughout with solid blocks varying in size from 100x100 ft to 200x400 ft and larger. It is these unmined Sewickley blocks surrounded by worked-out portions that have caused transmissions of roof stresses to underlying Pittsburgh mining areas, see Fig. 2, resulting in untold difficulty. As the Christopher Coal Co. operates both the Pittsburgh and Sewickley seams, accurate maps of workings in both seams are readily available and are regularly consulted. The first Pittsburgh squeeze attributed to overlying Sewickley blocks occurred in the Arkwright mine, where a shuttle car crew was developing a section consisting of seven panel headings. These entries were being driven in solid coal 3400 ft from the nearest worked-out Pittsburgh area. As mining advanced it was noticed that certain ribs began to slough and certain areas to show signs

Jan 1, 1952

By H. T. Hildage

Although Greater New York does not bear any resemblance to a great mining district, the mining operations that are being conducted in and about the city are both extensive and interesting in character. With regard to the extent, it may be mentioned that, at present, there is more dynamite used in New York than in any mining district in the United States; that there are under construction about 38 miles of tunnel, and that 66 miles more are projected, most of which must be constructed .in the near future; that since 1903 at least 2,000,000 tons of earth has been removed in underground work, in addition to about 3,500,000 tons that has been removed in open-cut in connection with tunnel-work, and many times this quantity that has been removed in excavating foundations for buildings not connected with tunnel-work; and that there are to-day probably more than 5,000 men engaged in mining-work in and about New lrork City. These undertakings include almost every operation connected with underground work, from exploration by means of trench and boring, to the sinking of large shafts and the driving of large tunnels through every kind of ground from hard rock to soft, semi-fluid silt and quicksand. It is proposed in this paper to give a general description of some of the methods and appliances used in the opening-up of a " mine " in a large city, and a brief description of some of the &'mines" now being developed in New York, connecting as far as possible the methods described with the particular work for which they were designed, in order to give a general idea of the

Jan 1, 1908