Search Documents

By D. J. Jr. McAdam

RESULTS of a general survey of corrosion-fatigue phenomena at the Naval Engineering Experiment Station were presented in five previous papers.1-5 In these papers references were given to the work of Haigh in 1917.6 The five papers mentioned gave a general survey of the behavior of metals when tested to failure under simultaneous corrosion and cyclic stress. As a result of this survey the fourth paper gave a tentative analysis of the corrosion-fatigue process. According to this analysis, if the initial stress is below the endurance limit but above the corrosion-fatigue limit, the corrosion-fatigue process is divided into two periods. The first period is the formation of pits. As the initial stress is below the endurance limit, the pitting is assumed to be due to corrosion, not to fatigue. The corrosion pitting, however, is not the ordinary pitting of stressless corrosion, but is an accelerated pitting due to the effect of the cyclic stress on the corrosion. As the pit progresses, both the actual stress and the effective solution pressure increase. The increase of actual stress is due to increasing stress concentration at the bottoms of the pits. The increase of effective solution pressure is due to the increase of actual stress. The mutual intensification of stress and solution pressure continues until the actual stress at the bottoms of the pits surpasses the endurance limit. The second period of corrosion-fatigue then begins. In this period the process is merely fatigue accelerated by the corrosion. The cracks advance at a continually accelerated rate until the specimen breaks.

Jan 1, 1930

By William Waters Van Ness

The Pierrefitte mines, situated in the South of France, in the district of the Hautes-Pyrenees, owe their name to the fact that the first mining operations of any extent, and of comparatively reccnt date, were carried out in the neighborhood of the village of Pierrefitte, which is a branch terminus of the Midi railway. The Pierrefitte mines, however, embrace a wide extent of country and several different concessions, on most of which comparatively little exploration-work has been done. The portion of the property presently to be described is a zone running roughly E—W., over a distance of about 5 miles from the valley of Cauterets to the valley of Estaing, the ridge dividing these valleys being a spur of the main chain of the Pyrenees, and running more or less at right angles to it. According to local tradition, which various indications tend to confirm, these mines are of ancient date, the first workings being attributed to the Romans, who are supposcd to have sought not only the lead but also the silver which is contained in the ore. Old slags have been found in the neighborhood which might well have been produced from the cupellation of lead-ores. These old workings, while of considerable extent at times, do not seem to have extended beyond a depth of 100 ft., even this depth being somewhat exceptional. The old notarial records of the district show that mines were known to exist, and that they were even worked, in the sixteenth century, but since the mines were abandoned (by the Romans or others) considerably prior to this period, very little

Jan 1, 1909

By A. H. Larson, T. P. McNulty

RECENTLY, an investigation of the absorption of sulfur dioxide gas in molten binary copper alloys was conducted. A Sieverts-type apparatus, consisting of a mercury-filled gas dispensing buret and a mercury manometer, was used initially for determining the volume of gas absorbed as a function of pressure. The equilibration behavior of the alloys studied indicated that the mercury in the gas measuring system was absorbing sulfur dioxide. Owing to the widespread use of mercury as a displacement medium in absorption studies, an investigation was made to determine the nature and magnitude of the mercury - sulfur dioxide absorption effect. The gas measuring system was modified by substituting a Worden Quartz Products Type PDHV fused-quartz-spiral pressure gage for the mercury-filled dispenser and manometer. The dispensed gas volume at known temperature and atmospheric pressure was measured by evacuating a Pyrex vessel of known volume and by admitting sulfur dioxide into the vessel until the attached quartz pressure gage registered atmospheric pressure. Atmospheric pressure was measured concurrently with a separate mercury barometer. The volume of the empty sample chamber and its attendant apparatus was determined by measuring the equilibrium pressure accompanying the addition of a measured volume of sulfur dioxide into the initially evacuated system. The volume of the mercury sample was calculated from the density of mercury at the temperature of the study (25°C). Measured volumes of sulfur dioxide were then dispensed into the system and the equilibrium pressure accompanying each gas addition was determined. From the difference between the system volume and the mercury volume, the number of moles of gaseous sulfur dioxide remaining in the system at each pressure was calculated. The difference between the number of moles of gas dispensed into the system, denoted Enso2: and the number of moles of gas remaining in the system after absorption equilibrium had been attained, denoted nso2(g), was equal to the number of moles of absorbed gas, denoted nSO2. The number of moles of absorbed gas was then converted to absorbed volume, denoted VSo2, in cu cm at stp conditions of (PC and 760 mm Hg. Table I contains calculated values of Snso2, nSo2(g), and VSo2 for different sulfur dioxide pressures. In the original system, denoted Run I, volume limitations of the gas dispensing system prevented absorption studies at equilibrium pressures near atmospheric pressure, so a different gas dispensing system, denoted Run 11, was used for determining the last pressure reading in Table I. The data in Table I are expressed in terms of the absorption of sulfur dioxide in 49.68 cu cm of mercury. In Fig. 1, these data are expressed in terms of the absorption of sulfur dioxide in 100 cu cm of mercury. Since the absorption data plotted in Fig. 1 show a linear relationship, the volume of sulfur dioxide absorbed in mercury is a function of the first power of pressure. The absorption reaction is So2(gas) = SO2 (in Hg) The first-power pressure dependence, coupled with the fact that the sulfur dioxide could be removed from the mercury by applying vacuum, indicated reversible

Jan 1, 1967

By Ray Light, Everett M. White

Numerous articles have been written about the coal miner ; he has been compared with brave men who have gone out to conquer some unknown hazard throughout the ages. Now, however, modern mining is no longer something to be avoided, but a vocation that anyone can be proud of, with remuneration equal to or above that of almost any industry. A concerted effort is being made each day by both the operators of most mines as well as the state and federal inspectors to see that coal mines are as safe or safer than work places in any other industry. However, it is true that mine fires and explosions have occurred in the mining industry since its inception. One of the earliest accurate references to such an occurrence is found in the transactions of the Royal Society of London. In the Colliery Managers' Handbook, 1898, Caleb Pamely writes of an explosion that occurred at Fatfield, England in August 1708, resulting in the deaths of 69 persons. He states: "Three of them, viz, two men and a woman, were blown quite up from the bottom of the shaft, fifty-seven fathoms deep, into the air, to a considerable distance from the mouth of the pit." It is interesting to note that women were employed as miners in England during that period. In the United States, the first record of coal mined was in 1702 by the Jamestown colonists. In 1786, about 20 years after Pittsburgh, PA was first settled, a charter was granted by William Penn to mine coal on the banks of the Monongahela River. Then in 1803, the first important coal company, the Lehigh Coal Co., was established. From this beginning, the mining industry continued to grow in importance and the first state mining law was formulated in 1870. The Pennsylvania state mining law was followed in 1873 by Ohio's, and in 1876 by Maryland's. A mine explosion at Avondale, PA in 1869 stimulated state legislatures to formulate these early laws. In 1907 near the town of Fairmont, WV, there were, within three days, two explosions resulting in a total of 597

Jan 1, 1981

By Dwight E. Woodbridge

DuriNg April, Max, and June, 1910, I was in charge of an examination of the greater part of the Moa iron-ore area in Oriente Province, Cuba, on the north coast, near the east end of the island. My instructions, on arrival at the properties, were to check former estimates of tonnages and grades, and to re-examine the ore comprised in claims covering 44,727 acres. This work included the running of lines dividing the properties into co-ordinate planes, the boring of many thousand feet of holes spaced at the intersections of these co-ordinates, the taking of samples of the ore penetrated, the analysis of these samples for their various constituent minerals, and the determination of the results as to tonnages, depths, and grades, both for individual properties and for the entire group. Each section of every one of the thousand holes drilled was to be compensated for depth and grade with every other, a series of simple arithmetical calculations of no slight magnitude, the mere mechanical labor of which consumed much time, but finally resulted in giving a complete average of all the essential facts for the entire area of 18,000 hectares, Had it not been for the more than willing, active, and able co-operation of the officers of the Spanish-American Iron Co., from Charles F. Rand, President, and Jennings S. Cox, General .Manager, down to the most humble water-carrier, the work would have consumed far more time than it did. The lands thus systematically explored by me were comprised in the following denouncements: Punta Gorda, Yaminiguey, Baracoa secunda, Sagua, Moa, Yajrumaje, Lirio, and Cabanas, all of which were massed as the Moa group, so called, and cover an area of 13,832 hectares, or 34,179 acres. Some 10,000 acres additional to this was included in neighboring properties, lying between Moa and the east end of the island, the Buena Vista,

Jan 1, 1912

By J. D. Meakin, H. G. F. Wilsdorf

Using a combined decoration and etching technique the dislocation structure of annealed and deformed a brass has been studied. Annealed crystals revealed a low density forest and well-developed subboundaries; lightly deformed crystals contained discrete groups of dislocations. The dislocation density and the number of dislocations in a group were obtained from the micrographs. Using slip-line data, the mean path of a dislocation and the configuration of groups along an active slip plane have been deduced. Observations on secondary and cross-slip are reported. It has been the aim of many investigations to obtain detailed knowledge of the dislocation patterns which are present in metals before and after their deformation. The "decoration" of dislocations with impurity atoms has been considered as one of the promising experimental approaches, and much work has been done to develop this technique for revealing dislocation sites in metals. Following the early work by Castaing,' Castaing and Guinier,' and Lacombe and Berghezan~ on aluminum-rich aluminum-copper alloys, dislocations in this material have been studied extensively by others.+' In these alloys the dislocation sites act as nuclei for the precipitation of the second phase. The main results of the investigations on aluminum with copper are: i) the confirmation of the earlier contention that subboundaries consist of dislocation walls, ii) that many more dislocations are found in slip bands than in regions where less glide had taken place, iii) the observation of individual dislocations, lying nearly parallel to the surface investigated, and iv) that parts of dislocation loops, apparently emitted from a dislocation source, could be made visible. Recently, Jacquet, Weill, and Calvert have succeeded in revealing nearly concentric dislocation loops in quenched A1-4 pct Cu and thus indicated directly the existence of dislocation sources in a fcc metal specimen of normal dimensions. Another decoration method developed by Dash10'11 and applied to silicon crystals makes use of diffusing copper to the dislocations from a surface deposition. The dislocation pattern can then be observed by an infrared technique. His results include evidence for symmetrical and spiral Frank-Read sources, and for arrays of dislocation loops which follow simple crys-tallographic directions. Recently Low and Guard" have studied the dislocation structure of silicon-iron using carbon for the

Jan 1, 1961

By H. S. Munroe

THE native copper of Lake Superior occurs in the form of fine grains and scales, disseminated in small percentage through the copper-bearing rock ; and in large and small masses, from a few pounds to several hundred tons in weight. Formerly the bulk of the copper came from the mines of Ontonagon and Keweenaw counties, producing mass copper. At present these mines furnish less than one-tenth of the total product, and fully one-half of this is from a single mine. The masses are usually found irregularly distributed in nearly vertical fissure veins, and require much dead work in sinking, drifting, and stoping for their development. The risk and expense attending the working of these mines have made them, with few exceptions, anything but profitable. * Read at the Montreal meeting, September, 1880.

Jan 1, 1880

By P. W. Bridgman

Flow and fracture are admittedly complicated phenomena of which we are yet only partially masters. There is not even nni-.persal agreement as to the details of the language best adapted merely to describe the phenomena, to say nothing of any theory. Certain points of view, however, are widely held, and there are certain general expectations as to what sort of procedures will prove permissible. A complete description of any situation involving fracture would demand a complete history of all the variables in the control of the experimenter. The experimenter endeavors so to choose his independent variables that they are adequate to determine completely the situation in the sense that when an experiment is repeated on the same initial material and with the independent variables running through the same sequence, all the other measurable properties of the system will also run through the same course. It is, I think, the universal conviction that when we are dealing with phenomena of flow and fracture, the most important of the necessary variables are the external forces acting on the various parts of the body; when the force history repeats, with certain obvious restrictions such as that temperature must be constant and non-mechanical forces, such as magnetic field, must be small enough to be ineffective, then the history of all measurable properties will repeat; in particular the alteration of geometrical shape due to flow will run through the same course, and when fracture comes, the character of the fracture will be reproduced. Complete mastery of merely the descriptive aspects of flow and fracture would demand the ability to predict the entire course of flow and complete characterization of the final fracture for every possible combination of forces, varying in time in all possible ways, when applied to bodies of all possible shapes. This full situation is obviously of prohibitive complexity. The first stage in reduction to manageable simplicity is to resolve the total situation into the sum of contributions made by small elements. Our thesis is that if each of the elements is adequately characterized, the behavior of the whole system is fixed. The element is usually taken of a simple geometrical shape, suggested by the mathematics best adapted to the particular situation. The forces acting across the faces of the elements are ultimately determined by the forces acting across the free faces of the whole system. The detailed process of finding the precise forces on the faces of all the elements in terms of the external forces involves the use of a special mathematical invention, the stress, a constructional quantity consisting of six components. The stress at any point in the body is determined by both the external force system and by the physical properties of the body at all points; quite different stresses prevail at the interior of bodies of the same shape under the same external forces in the elastic and plastic ranges. The forces on the faces of any element are, however, uniquely determined by the stress system at the element. Our fundamental thesis

Jan 1, 1945

By J. D. Prater, H. R. Spedden, E. E. Malouf

With the expansion of copper leaching of the various mine wastes at the Kennecott properties, additional copper recovery facilities have been required. A research and development program has been pursued to determine a suitable economic approach to the processing of the additional leach solutions contemplated. lnvestigations on laboratory and pilot plant scales covered electrowinning, solvent extraction, launder and vat type cells, activated launders, precipitation drums, and precipitation cones. This paper contains information on the development and use of a new precipitation-cone-type copper recovery plant, which provides many advantages over older systems. The application of research findings to the old art of leaching copper from copper-bearing mine waste has resulted in a significant contribution of copper to over-all copper production. For example, at the completion of the current expansion program at the Kennecott properties in the United States, copper produced from waste dump leaching will amount to about 25% of the total production. Formerly only 2% was derived from this source. This planned expansion of copper leaching focused attention on the problem of developing more efficient methods for the recovery of copper from greatly increased volumes of copper-bearing solutions.1 The detailed investigations which have been made in laboratory pilot plant and plant tests for the recovery of copper from copper-bearing solutions have included electrowinning, solvent extraction, ion exchange and cementation with iron in launders, precipitation drums, activated launders, and precipitation cones. The results of these investigations have led to the development of a new precipitation cone-type copper recovery system providing many advantages over older methods. ELECTROWINNING OF COPPER FROM COPPER-BEARING SOLUTIONS The direct electrowinning of copper from relatively dilute solutions of copper-bearing mine water, namely solutions containing 10 to 20 lbs of copper per 1000 gal, has always been an attractive possibility.2,3 By this method, high-purity copper powder can be recovered with a power consumption of 3.5 kwh per Ib of copper. However, once the solution strength de-

Jan 1, 1967

By C. R. Swarts

The use of compressed air or gas in oil wells for raising crude oil to the surface has, within the last year, become a dominant factor In production engineering. Previous application of this principle was largely confined to oil wells that had been pumping for a considerable length of time. In the Seminole area, the gas-air lift has been applied to wells imniediately after natural flow has ceased and in some cases while the wells were still flowing. This early application of the gas-air lift has been watchcd with intense interest by the petroleum industry, both with respect to methods of application and mechanical installations and to the effects on immediate and ultimate production. Methods of Application The Seminole pool at its inception contained sufficient gas associated with the oil to cause natural flow. As no frce gas was found in the main productive horizon, the Wilcox sand, all the gas present was dissolved in the oil, hence the natural flowing life was short, rarely lasting over 45 days. When natural flow ceased, high fluid levels were common, and as depth and crookedness of holes were obstacles to efficient pumping, the gas-air lift was used almost exclusively in raising the oil to the surface. Because of the high gravity of the oil, 41" A. P. I., and its high gasoline content, and also because of the desire to obtain production before offset wells became productive, quantity of production was the aim of the operators and a method of flow was used whereby this aim could be fulfilled. One of the outstanding features of this method consisted in flowing the wells through the annular space between the tubing and rasing. By this means a greater quantity of fluid could be handled than by flowing through the tubing of the size in ordinary use. Wells that would produce only a few hundred barrels on the pump were by this rnethod made to produce as high as 7000 bbl. on the lift. A few days or wreks of production at that rate meant a large recovery of oil. Casing of 636 in. diameter was commonly used as a production string with a 5 3/16-in. liner set on top of the oil sand. Upset tubing for irtro-

Jan 1, 1928

By V. C. Perini

The 1943 designation of districts for the Transactions† has caused some confusion because of the elimination of the West Central Texas district and the allocation of the counties of this district to the North Texas district and the North Central Texas district. The North Central Texas district as herein defined includes the counties of Brown, Callahan, Cole-man, Comanche, Coryell, Eastland, Erath, Fisher, Hamilton, Hood, Jones, Lampasas, Mills, Nolan, Palo Pinto, Parker, San Saba, Shackelford, Stephens, Stonewall, Summerville, Taylor, Throckmorton and Wise. These counties as listed are the counties of District 7B, State Railroad Commission. This district covers the south central crest and the west flank of the Bend flexure north of the Llano uplift. The west flank of the Bend flexure is on the east boundary of the Permian Basin of West Texas. The North Texas district, District No. 9, State Railroad Commission, includes the counties of Archer, Clay, Cooke, Foard, Hardeman, Jack, Knox, Montague, Wichita, Wilbarger and Young. The area of this district covers the crest and south flank of the Red River uplift and the north central crest of the Bend flexure. The greater part of the oil and gas produced in the past from the North Central Texas district has been from Pennsyl-vanian strata. Some oil and gas has been produced from the lower Permian (by the latest selection of the Pennsylvanian-Permian boundary') and minor amounts from the Mississippian and Ordovician sediments. Increasingly important quantities of oil and gas are to be expected from the older sediments by deeper development in proven fields and by new discoveries. Most of the oil and gas in the district has accumulated in localized, well-defined structural traps in limestone and sandstone reservoirs and in traps due to stratigraphic changes in sedimentation, mainly porosity traps in limestone and sandstone lenses, both usually associated with some structural feature. The Stripper Well Premium Plan as adopted by the office of the Federal Price Administrator has been an aid to the producers of stripper wells. The producers are pleased to receive the subsidy to prolong the plugging of wells, but they are not too pleased with the subsidy plan in principle. Most independent operators are in favor of, and think they are entitled to, an increase in the market price for oil. The price is not adequate to meet the requirements of the average independent operator with the continued advance in production, development and wildcatting costs. Old and new pipe lines for oil and gas leading out of the state are removing reserves at an alarming rate. Curves showing the rate of discovery versus production and pipe-line deliveries in and out of the state make a cross that sooner or later will be fatal to the state. Wildcatting not only needs a price increase but every other available incentive and encouragement.

Jan 1, 1945

By George Boulter

Draglines 8.2-1 Introduction. The nature and characteristics of rock and rock derivatives forming the crust of the earth vary so greatly from place to place that it is impossible to use the same numerical factors to show the, productive ability of excavating equipment on different jobs or projects. Factors for each project must be developed individually and applied as the conditions and requirements dictate. TYPES' OF DRAGLINES. Types of draglines are differentiated by the propelling method used and are generally divided into four classes, as follows: 1. Wagon mounted 3. Crawler mounted 2. Truck mounted 4. Walking Figure 8.2-1 shows a truck-mounted dragline. This type is considered to be the most mobile unit. In order to increase stability over the side, outriggers are installed as part of the truck chassis. This feature is not shown in .this figure. Figure 8.2-2 shows a crawler-mounted dragline. The long, wide crawlers are used to increase the stability and reduce the bearing pressure of this unit. These features allow for use of these units on surfaces too soft for the wagon- or truck-mounted types. Figure 8.2-3 shows a walking-type dragline. The large diameter tub and the well-supported boom through the gantry gives high stability for rugged works over a long life. BASIC PARTS OF A DRAGLINE. The basic parts of a dragline are illustrated in Fig. 8.2-4. A deck layout is shown in Fig. 8.2-5 with the main components named. OPERATION OF A DRAGLINE. Following is a description of the steps and controls present in a typical cycle of operation of a large dragline having independent hoist and drag motors. Starting the cycle with positioning the bucket on the ground under the point of the boom, the next step is

Jan 1, 1968

By W. Kennedy

THROUGHOUT northeastern Texas we have an extensive series of iron-ore deposits, occupying portions of nineteen counties and having approximately an actual ore-covered area of 1000 square miles. The existence of these ores has long been known. Kennedy* says: "Iron-ore is distributed in profusion throughout Texas, being found almost everywhere except in the level region of the coast." Before this, C. Newell† had mentioned the existence of these ores thus: " Iron is found in abundance in the eastern, northern and middle portions of Texas;" and in 1849 Edward Smith‡ said: " We met with immense hills of iron which were said to be, and appeared to be, of excellent quality, in Cass and Titus counties.. . .. It is well known that Texas abounds with iron of first-rate quality." In 1859, Dr. Shumard? reports that detailed surveys had been made in several counties, and says: " Our labors have demonstrated the important fact that we have a vast iron-region in the eastern part of the state, embracing considerable areas in Cass, Harrison, Rusk, Panola, Smith, San Augustine and Shelby counties. The ore-deposits belong to the Tertiary era and consist chiefly of hematites and limonites, of which there are several varieties. We have also found in this district extensive beds of carbonate of iron." Dr. Shumard gives no very exaggerated description of Cass county§ as it then existed when he says : " Cass county alone is capable of supplying a number of furnaces with an abundance of excellent iron-ore for many years." Of Rusk county he says: "Our de-

Jan 1, 1895

New Jersey Zinc Co. - The Plants Canon City Palmerton Depue

Jan 12, 1953

By Charles Will Wright

The application of the camera as an adjunct to topographic mapping began practically with its invention, and it has been employed with varying success since that time. With the exception of the camera to be described, the plate-camera has been universally used in this work, thus giving a projection of the area photographed on a flat surface. From such projections or photographs, by the rules of geometry and of perspective, points defining topographic features and seen from at least two camera-stations may be projected upon a ground-plane—the map.' In 1904 I employed the plate-camera for this purpose in Alaska, but found that the labor necessary to plot the maps, even in a general way, was long and tedious. In 1905 a small Eastman panoramic camera was fitted with spirit-levels, a sight-alidade and a transparent scale, introduced inside the camera to register the degree-points in the sky-line of the film-negative ; also, arrows to indicate the horizon-line. This was, on the whole, successful; but the details in the topography were not brought out in the views with sufficient clearness, aid the photographs were too small. These difficulties were overcome by obtaining a larger and more carefully constructed instrument, which was satisfactorily employed in the field during the year 1906. A panoramic view is made up of an integral number of perspective views upon flat surfaces, and logically is the most accurate and direct means to obtain an impression of a field of * Published by permission of the Director of the U. S. Geological Survey. Stanley, H. M. Photographic and Co-ordinate Surveying, Bans., xx., 740 to 766 (1891). Also, Flemer, J. ,4. Phototopographic Methods and Instruments, Report U. 8. Coast and Geodetic Survey, pt. 2, app. 10, pp. 619 to 735 (1897).

Jan 1, 1908

By Stephen Krickovic

THERE is today no proven continuous mining machine that can be used under all the varying conditions found in most bituminous coal mines. During the last five years, however, both the machines and methods of using them have been improved. Coal operators can now exercise a fair degree of selectivity, except those who must struggle with thick and hard partings and operate in seams less than 40 in. thick. It must be realized, then, that more than one type of continuous miner may be used advantageously in the same coal mine. Although this appears to violate the standardization generally sought after, the gain can more than offset added maintenance and, to a lesser degree, operating problems.

Jan 12, 1957

By Philip D. Anderson, Ralph Hultgren

Heat contents of extremely pure iron were measured over the range 300"to 1433"K, using a diphenyl ether calorimeter. Results from three samples containing widely differing impurities agreed with one another and with Previously reported results at higher temperatures (1184 ° to 1809°K) by Olette and Ferrier. From these data a table of heat contents of iron has been Prepared which is believed to be more accurate than those previously available. CP values have been derived which are consistent with these heat contents, with the best experimental Cp data, and with the thermodynamic conditions of equilibrium between bcc and fcc iron. The opinion is expressed that low-temperature extrapolations of presently known Cp values for y-Fe are not reliable. It would seem that the thermodynamic properties of iron, which is by far our most important metal, should have been well established long ago. This is not the case, however. As discussed by Olette and Ferrier,' there is objection to every earlier heat content measurement. While the best true Cp determinations agree well at temperatures below the Curie point, there is wide divergence at higher temperatures. Several investigators have examined available data and attempted to calculate thermodynamic functions for iron that are consistent with the two equilibrium temperatures of bcc and fcc iron. The two primary efforts were those of Austin' in 1930 and Darken and smith3 in 1948. The recommended values differ considerably; integration of Austin's Cp values leads to a heat content at 1100°K which is 300 cal per g-atom higher than the value recommended by Darken and Smith. The compilation of Fisher4 in 1949 was based on the selection of Austin. In 1956, Weiss and Tauer obtained yet another set of values by resolving Cp values into components due to dilation, lattice vibration, electronic excitation, and magnetism. The magnitude of contribution by each component and its dependence on temperature was estimated by semiempirical means. Their values are not self-consistent in that they do not form smooth curves when plotted vs temperature; moreover, their calculations cannot easily be repeated since they do not give the values of some of the parameters used. Clearly, experimental values for iron were in a most unsatisfactory state. The presently described measurements of the heat content of iron were therefore undertaken, covering temperatures as high as 1433°K. While the work was in progress, the high-temperature (1193" to 1789"K) heat content measurements of Olette and Ferrier' were published; in the region of temperature overlap the present results agree with Olette and Ferrier well within experimental accuracy. It is believed that the present results, combined with those of Olette and Ferrier, provide for the first time a reliable set of heat contents of iron from room temperature to the melting point. From these data, guided by available Cp measurements, it proved possible to derive Cp, entropy, and free energy function values for @-iron from room temperature to the melting point, and for y- iron in the temperature region of its stability. Exhaustive study led to the conclusion that extrapolations of y-iron functions to room temperature were not reliable enough to be useful; hence these have been omitted from the tables. EXPERIMENTAL Materials. Three samples of extremely high purity iron from different sources, containing widely different impurities, were measured. The first of these, designated "Chipman", was kindly supplied by Dr. K. K. Kelley of the U. S. Bureau of Mines from a lot which was made many years ago by Dr. John Chipman of the Massachusetts Institute of Technology. The second, designated6'Teddington", was supplied by the National Physical Laboratory, Teddington, England, from a lot zone-refined by them. The third sample, designated "Irsid", was supplied by the Institute de Recherches de la

Jan 1, 1962

By E. S. Machlin, S. Weing

GRAIN boundary stress relaxation has been the subject of several investigations in recent years, but as yet the phenomenon is not well understood. One of the major difficulties has been the lack of a sufficient amount of data with which to evaluate any proposed mechanism. Little information is available on the effect of small amounts of substitutional solutes on grain boundary stress relaxation. It is with this important phase of the problem that this investigation is concerned. The influence of substitutional solutes on grain boundary stress relaxation has been recently investigated in copper by Pearson: and in aluminum by Dorn et al.' Pearson studied the effect of zinc, gallium, germanium, and arsenic on the relaxation peak of OFHC copper.* The pure OFHC copper decreased the peak intensity and a second peak appeared at a higher temperature. This latter peak was termed the alloy grain boundary peak. At the lowest binary concentration studied, approximately 1 atomic pct, the primary peak was almost completely obliterated. Pearson found that the activation energy calculated from the alloy grain boundary peak for all solutes, irrespective of the concentration, was 44,000 cal per mol. Pearson concluded that the increase in activation energy from 33 to 44 kcal per mol is not continuous but abruptly changes from the lower to the higher value. As no attempt was made to investigate the intermediate range of concentration and hence calculate the possible variation of the activation energy for the initial grain boundary peak, this conclusion is hardly valid. In contrast to these results, Dorn et al. studied the effect of zinc, silver, copper, germanium, and magnesium on the grain boundary stress relaxation of aluminum. No change in the energy of activation was observed for binary alloys of the flrst four solutes, but a linear increase was found for increasing concentration of magnesium. Saturation was not found up to the maximum of 1.6 atomic pct. The energies of activation were obtained by plotting the horizontal displacement of the dynamic modulus curve vs temperature for two vibrational frequencies. As the modulus is proportional to the square of the frequency, this requires the measurement of the torsional frequency over a range of temperature. However, the technique does not lead to an unambiguous interpretation of the grain boundary

Jan 1, 1958

By V. G. Mooradian

THE diffusion of metal atoms into the crystal lattice of another metal and the assumption of regular positions to form a homogeneous alloy are some of the most fundamental phenomena of structural metallurgy. The mechanism of this process has been the subject of a great deal of study from many viewpoints, but the picture is still far from complete. It is generally believed that if one metal is to diffuse into another, the first must have some solubility in the second1. This means that the solvent must be able to accommodate the stranger atoms, either on points of its own lattice or in the interstices between, without losing its own crystal-lographic identity. It is also a general observation that cold-working is a distinct aid in the diffusion process, causing it to take place with greater rapidity at the same temperature or with the same speed at a lower temperature. There is considerable doubt, however, as to the real significance of the deformation in its effect on the diffusion mechanism. Several factors associated with the cold-working may be responsible for the increased diffusion rate. The plastic deformation causes a distor-tion of the solvent lattice, which may be an aid in the assimulation of atoms of another kind. There are many references2 in the literature that suggest that some distortion or "loosening" of the lattice is necessary for atomic migration and that diffusion cannot take place in the undis-

Jan 1, 1935

By Kenneth Seaver

(San Francisco Meeting, September, 1915) INTRODUCTION IT is rather gratifying that in the field of the manufacture 'of refractories, in which, as a whole, foreign practice has surpassed us, the United States stands pre-eminent in the making of silica brick. In some instances European manufacturers have refused point-blank to credit the possibility of making to such specifications as are common with us, until the actual 'completed shapes were shipped for inspection. But both the manufacturer and consumer in foreign lands are now frankly learning from us, and benefiting by our advanced practice in this field, as is evidenced by the orders placed here and the efforts put forth abroad to come up to the standard of American-made material. In no metallurgical operation has the employment of silica brick spread with. such leaps and bounds as in the building of plants for the carbonization of coal, particularly in the byproduct coke oven. Today, in practically all types of oven, the structure above the floor level (except the facings) is of silica, while in the recuperative and in some regenerative types, its use is extended to that portion of the oven below the floor as well. By reason of the fact that there are a number of classes of refractories of higher silica content than the usual so-called fire-clay brick, there is sometimes a misunderstanding as to the class of material referred to as "silica" brick. We here refer only to a brick having a silica content of 94 per cent. or more and made usually from quartzite rock with a small percentage of lime as a binder. The term "silica" brick is sometimes rather loosely applied to brick front highly siliceous clays, or to a quartzite refractory of mingled fire-clay and quartz rock; but such products are not considered in this discussion.

Jan 9, 1915