Search Documents

By M. F. Williams, L. G. Hendrickson

IN classification of pulps bearing magnetized ferromagnetic particles, depolarizing is of great importance. If size separation is to be effective, particles must be individual rather than in floes. Depolarizing is also practiced in heavy medium separations in which ferrosilicon or magnetite is the medium. When particles of ferromagnetic material have been removed from a magnetic field, residual magnetism causes agglomeration. The term depolarizing refers to the operation of reducing or eliminating this residual magnetism and may thus be considered magnetic deflocculation. The terms demagnetizing and randomizing are also used. At the Research Laboratory of Oliver Iron Mining Div. in Duluth a method was developed for measuring depolarization of the pulp of ferromagnetic material. Experiments were made with Mesabi taconite,' a natural magnetite of low coercive force. Ferromagnetic materials of higher coercive force, such as lodestone or the artificial magnetite produced by reduction roasting of hematite, present a more difficult problem, which was not within the scope of this investigation. It is possible, however, that some of the techniques evolved for measuring and calculating electrical characteristics of alternating current coils would be of use in depolarizing high coercive force material, particularly in conjunction with high-frequency alternating current, as proposed by Hartig and others.'," Properties of Ferromagnetic Materials:'7 Experimental work, described below, has shown that if a sample in the magnetized state is heated above the Curie point and cooled, much of the preferred orientation is destroyed and the sample is substantially depolarized. It has been thought that when the sample cools below the Curie point the domains cancel each other, leaving a zero net moment. However, such particles still exhibit a tendency to cohere, and undoubtedly this is caused by the forces of residual magnetism. -AS measured by the percent depolarization, this tendency is reproducible for any sample upon repeated heating above the Curie point and subsequent cooling and is independent of the initial state of magnetization. It is postulated, therefore, that as the material is cooled below the Curie point the domains in any particle do not completely cancel each other, but rather are preferentially oriented to some extent. Mechanism of Depolarizing with Alternating Current Magnetic Fields: It is believed that when ferromagnetic material is passed through an alternating magnetic field, depolarizing occurs in the decaying portion of the field. As the particles pass through the portion of highest intensity they become magne- tized. If the particles are not free to move, the polarities of the particles will be reversed (by a mechanism similar to that described above for magnetism) at a frequency equal to that of the applied field. As the material moves through the decaying field, intensity levels become such that a domain does not completely reverse, but stops on an axis of easy magnetization. By the time the material reaches the point of zero field intensity, a state of fairly random orientation of domains is achieved. If conditions are such as to give a completely random orientation, the particle will have little or no external magnetic field, and a pulp of such particles will be depolarized. Previous Work In 1918 E. W. Davis was granted a patent for demagnetization of magnetite pulps.' His method consisted of passing the pulp through a tapered coil, activated by alternating current of normal frequency (60 cycle). This method, with minor modifications, has been used almost universally in all pilot plants and commercial installations in which depolarization of low coercive force materials has been required. Hartig, Onstad and Foot2,3 avd made a detailed study of the factors involved in depolarizing both low (below 100 oersteds) and high (above 100 oersteds) coercive force material. They developed a method for evaluating the relative degree of depolarization of any pulp based on the settling characteristics of the pulp. Their standard of comparison was a sample heated to above the Curie point and cooled in a zero field, all in a neutral atmosphere.* For low coercive force material they found treatment.Thisprocedure is subsequently called, in this report,theCurie that results equivalent to Curie treatment could be

Jan 1, 1957

By M. C. Dow

INTRODUCTION BELT conveyors generally are conceded to be the most economical method yet devised for the transportation of large quantities of bulk materials within plants. Belts are coming into greater use for transportation over long distances and are replacing other forms of long-haul conveyance. It is not the intent of the writer to comment on the design of belt conveyors, but to offer some suggestions for improvement in the operation of conveying belts, based on many years experience with belts in several stonecrushing plants. It is the contention of this writer that opportunities for improvement not fully realized by most operators exist in many plants and that a study of the individual conveyors can result in lower unit belt costs. GENERAL RELIABILITY It is the fool-proof nature and general reliability of the belt conveyor that is responsible for its neglect. Even when abused, a belt will carry large tonnages and last a long time, often outlasting the personnel responsible for its care. Some operators look upon the purchase of a new belt as an expensive outlay every so many years, rather than a constant and steady cost amounting in belt wear alone to several dollars every operating day. This belt wear for all conveyors in one stone-crushing plant known by the writer costs 1 1/2 cents per ton or $12 to $15 per hour, based on the present cost of belt replacements. The fact that these replacement costs are double those of prewar quality emphasizes the necessity of improving the conditions that make belts wear out. Some of those conditions are the responsibility of the conveyor designer, and if a serious original error has been made, this handicap cannot be overcome by the operator. If the belt is too narrow, too steep, or too fast for good loading, the operator finds that he has an inherently expensive belt. The other factors that decrease the life of a belt are more or less under his control. The two factors of most importance are the loading conditions and the alignment. Most of the cover wear and carcass cutting occurs at the loading point and if the alignment is not good under all conditions, edge wear or damage may result, Fig I. LOADING THE BELT It is difficult to load a belt in an ideal manner; that is, to flow the material on the moving belt at a steady rate, without impact, without turbulence, and with a velocity equal to and in the same direction as the belt. An inclined belt is especially difficult to load and particularly when its speed is over 300 or 350 fpm. Inclined conveyors require longer skirt plates to prevent spillage until the load settles. It does not seem reasonable to expect an inclined conveyor to carry the same load as a horizontal belt of the same width and speed, because of the difficulty in loading

Jan 1, 1947

By S. Le Fevre

The application of electricity to the mining and beneficiation of the magnetic iron ores of the Mineville, N. Y., district, on Lake Champlain, has resulted,in economies and enhanced quality of product, without which only a comparatively small quantity of the present output could be marketed. The output of the Witherbee, Sherman & Co. mines is about 700,000 tons per annum, and of this about four-fifths is treated by magnetic separation to increase the iron content and reduce the phosphorus. The use of electricity for the magnetic separation of the ore from the gangue is therefore of primary importance, and makes possible the application of electric power for mining and preparing the ore for concentration. The fact which speaks loudest in favor of the application of electricity is this: It is possible for about 25c. per ton of shipping ore to furnish all the power required to put the ore on cars. This includes mining a hard ore underground, from a depth of 900 ft., hoisting to surface, crushing to $ or 8 in. in size, and separating from the gangue. This also includes lights about the works, and all miscellaneous power, such as about the shops. The first plant for the generation of electric power for use at Mineville was completed in 1903, and was one of the first for the application of electricity to mining iron ore. This was a Nordberg compound condensing steam engine, direct connected to a 750-kw. alternating-current generator, 3,300 volts, 3 phase, 25 cycles. All the plants added later use the same current but with higher voltage. The map, Fig. 1, shows the power plants and the transmission system; Figs. 2 and 3 are views of the shaft houses and the mills. The power from the first plant was distributed to Mills 1 and 2, one 2,500 cu. ft. compressor, and to the Harmony hoist, which was driven by a 300-h.p. motor operating four 10-ft. drums. Our experience with the hoist covers largely the development of electric hoisting from 1903 to date, and in some cases improvements were worked out to satisfy our needs. The motor is still operating as installed, but the control apparatus has been radically changed several times. When installed, the iron re-

Jan 1, 1915

By E. D. McMurry

INTRODUCTION Before discussing the use of the free piston; it may be well to explain briefly the type of gas lift valves with which the loo] is designed to function. The gas lift valve ii nothing more or less than a small back pressure regulator. It; construction consists of an outer hous ing covering a seamless metallic bellows in such a way as in form a sealed pressure vessel or pressure dome. To the bellow* in attached a stem and to this stem is attached a .rating member. When the valve is run into the hole, a pre-delermined pressure charge is placed in the pressure dome. As shown in Fig. 1. the valve is furnished in four different major assem-blies. to accomplish good results in different types of wells. The valve is mounted on a pup joint (Fig. 2a) : the eoin-plele assembly is entered into the tubing siring at the desired location. Each valve is furnished with a revere flow check valve (Fig. 2-b) to eliminate any back wash through the mechanism. Valve action is as follows: At any time the casing pressure is allowed to exceed the pressure forces within the pressure dome of the valve, the valve simply opens and passes gas from the rasing annulus into the tubing. When the casing pressure forces arc allowed to bleed to a force less than the pressure force within the dome, of the valve. the valve closes. With this type of construction. it is possible to open and close the valve or valves at will from the surface, the medium of the gas pressure in the rasing annnlus. The cycle of operation is governed by a tine cycle motor valve, commonly referred to as a gas lift interutitter or gas life surfacr controller (Fig. 3). In actual practice. after the well is unloaded only one valve is in operation . . . all other valve.: remain in the closed position. On pre-determined time cycles, it is possible to open and close this operating valve at will, and to pass the desired amount of gas through this valve wheneler needed. This method of gas lift is widelv used and has been found In be very efficient. However, it has long been known that even greater efficiency would be obtained if it were possible to place Piston between the injected gas and the fluid head. The free piston which will be discussed here was designed to accomplish this end and has been found to do so with very satisfactory results. DESIGN AND OPERATION OF THE FREE PISTON Basically. the free piston consist- of a telescoping assembly in which are incorporated the various control and operating parts (Fig. A set of sleeve valves which are opened and closed by movement of the telescoping section is contained in the. tool. A cross section of the free piston is shown in Fig. 4-11, 'rile main body cotain- a seamless monel bellows of the same type as that generally used in pressure charged gas lift valves (Fig. 4-c), and a valve core to permit placing a pressure charge in the bellows before the free piston is placed in service. The bellows is the main control unit of the free piston and performs two function: 1. It governs the opening and closing of the sleeve valves. a.: dictated by the producing activities of the well in which the piston is operating. 2. In its normal position, it holds a rubber packer in an elongated position to permit passage of fluid between the packer and the tubing walls. The lower section of the free piston contains a hydraulic shock absorber which cushions the return of the tool to its

Jan 1, 1953

By G. S. Rice, J. A. Davis

The Péchelbronn oil field is located in the province of Alsace, in the Rhine Valley, about 30 miles north of Strasbourg. It is approximately 4 miles wide and 12 miles long, extending from the villages of Lobsann on the north to Wintershausen and Ohlungen near Haguenau on the south. (See Fig. 1.) The productive area includes about 44,000 hectares (107,680 acres). The name Péchelbronn signifies "pitch-spring" or "pitch-fountain." The first exploratory galleries were driven in from the hillside in 1735; and in 1745 the first official concession was granted by the French government and the first pit sunk to a depth of about 30 ft. Extraction by drilled wells was begun in 1879, supplementing the mining operations, and during the next 10 years 200 wells were drilled to an average depth of 172 m. (568 ft.). The bringing in of two "gusher" wells, in 1882 and 1888, respectively, was followed by the abandonment of all underground work. Underground mining, with a view to increasing the production of petroleum by recovering the oil left in the sands after drilling wells, was resumed in 1916. This mining operation started by sinking shaft No. 1 to a depth of 150 m. (495 ft.). The underground developments were pushed during 1917 and 1918 and the annual production of the Péchel-bronn field was increased to about 50,000 metric tons or 350,000 bbl. On the signing of the Versailles Treaty the province of Alsace, which had been taken by Germany as the result of the war of 1870, was returned to France, and the proprietary rights were taken over by the French Government. Concessions or leases, which embraced all the known oil-bearing territory of the field, were granted to the present operating company, Mines de Péchelbronn. This company followed both the drilling and the mining methods of the previous company.

Jan 1, 1927

By E. R. Stover, J. Wulff

A tentative 870°C isothermal section, the solidus equilibria, and the solubility of Tic and graphite in the nickel solid solution have been determined with arc-cast specimens. Each of the Ni-Ti intermetallics forms two-phase fields with Tic; only Ti,Ni has a measurable solubility for carbon. A quasi-binary eutectic exists between Tic: and a titanium-rich nickel solid solution; ternary eutectics occur on either side, with TiNis or with graphite. Graphite is in equilibrium with a nickel solid solution containing a ratio of Ti/C which increases below the solidus. DURING the past decade, titanium-carbide cermets containing nickel or cobalt alloy binders have been widely studied for high-temperature and wear-resistant applications. Recent work has emphasized control of the carbide grain size and distribution2's and the thermal exparision match between the phases/ The present study was initiated to determine the phase compositions during the sintering or infiltration process, and during subsequent heating. Although the effects of additives and impurities in commercial compositions are important, it was necessary to consider first the pure ternary, Ni-Ti-C. Emphasis was placed on the nickel corner, since the nickel solid solution is the continuous phase in compositions having highest strength. Early metallographic work by Zarubin and Molkov- showed that solid solubility at either end of the section Ni-Tic is small. Edwards and Raine reported that nickel dissolves between 3 and 5 wt pct Tic at 1250° C, on the basis of microstructures of annealed, vacuum-melted powder mixtures. Although the solubility of nickel in Tic has not been measured, Tic formed by the menstruum process in liuid-iron solution contains as little as 0.06 wt pct Fe. BINARY SYSTEMS The most recent determinations of the three binary systems are summarized in Fig. 1. Titanium carbide (6) is predominant among the binary phases, and it melts above the boiling point of nickel. The Ni-C binary is based on separate liquid solubility' ) and solid solubilitylo measurements. The eutectic temperature, 1328OC, is taken from the solidus determination described below. However thermal analysis data by Morrogh and williams also show eutectic arrests in this vicinity in the absence of supercooling. The Ni-Ti binary is taken from the work of Poole

Jan 1, 1960

By J. B. Newkirk, A. H. Geisler

The alloy Cu4Pd has a disordered face-centered-cubic structure when quenched from temperatures between 478ºC and the melting point (about 1100°C). Below 478ºC an ordered phase is stable. The results of a Debye-Scherrer X-ray analysis indicate that the ordered phase has a tetragonal unit cell described by the space group C24h — P42/mt with 2 Cu in 2a, 2 Cu in 2f, 4 Cu in 4j (x = 0.2, y = 0.6), 4Pd in 4j (x = 0.4, y = 0.2), and 8 Cu in 8k (x = 0.1, y = 0.3). The orientation relationship between the face-centered-cubic phase and the ordered tetragonal phase is given by: [100],,. // [130]al,. COO1Ia.d.//COO1I,,.. • The behavior of Cu,Pd is typical of ordering alloys except that the transformation is very sluggish. The increase in hardness and the microstructural and X-ray diffraction effects are interpreted in terms of coherency strains caused by the ordering. AN anomalous construction in the Cu-Pd phase diagram (Fig. 1) was reported in 1939 and has been allowed to stand without further published attention since that time. The odd figuration about the composition 10 to 27 atomic pct Pd is derived mostly from the work of Jones and Sykes.1 Evidently several features of this binary system require further study if the constitutional forms are to be well understood. The present paper includes a study of one of these features, that is, the crystal structure of a single ordered alloy containing nominally 20 atomic pct Pd. This choice of composition was suggested by the work of Harker and associates who determined the structure of Ni4Mo2 and Ni4W.3 The nature of the ordering process in Cu4Pd was studied also by observing the hardness, microstructure, and Debye-Scherrer patterns of specimens which had been aged at various temperatures after quenching from an initial disordering treatment. Experimental Methods A 20 gram ingot of Cu4Pd was made by melting spectrographically standardized copper from Johnson, Matthey, and Co., and commercially pure (99.5 + ) palladium in an argon-filled quartz tube. Chemical analysis showed that the ingot contained 80.0 atomic pct Cu. The ingot was rolled about 60 pct to a strip 0.060 in. thick and was homogenized for 16 hr at 950°C in low pressure argon. Rods cut from the rolled strip were worked into wire 0.015 in. in diameter, and specimens for hardness and microscopic examination were cut from the remaining strip. All specimens, with the exception of some of the wire, were given an initial disordering treatment by heating for 16 hr at 950°C, followed by water quenching. A 10 cm length of as-drawn wire was water quenched after being held in a temperature-gradient furnace4 for 89 days. Room-temperature Debye-Scherrer photograms were then made at points along the wire to determine the temperature below which the ordered phase was stable. Although the accuracy of temperature determination in the gradient was only about ±10 °C, the temperature gradient was sufficiently gradual that the sensitivity was much better and locations which had differed by as little as 1°C could be distinguished. An analysis of the crystal structure of the well ordered alloy was made by X-ray diffraction using a specimen cut from this wire. The change of Debye-Scherrer pattern as ordering progressed was studied by using isothermally aged samples of initially disordered wires. The wires were sealed under low-pressure argon in small quartz tubes for heat treatment. After the aging treatment, the tubes were quenched in water and photograms were made at room temperature in a 10 cm diam camera using filtered Cu kX. (A = 1.540511) Hardness was measured on a Vickers hardness tester using a 10 kg load and 2/3 in. objective lens. Reported values are the average of at least three impressions made on flat specimens 0.060 in. thick. After the hardness of a heat-treated sample had been measured, it was resealed in low-pressure argon and returned to the furnace for continued aging at the same temperature. In this way, two samples served for all aging times at each temperature. Hardness specimens which had been aged 500 hr or more were used for metallographic examination after the final aging treatment. A dilute potassium-dichromate etching solution was used.

Jan 1, 1955

By Y. C. Liu, W. R. Hibbard

Based on pole figure data and microstructural observations, the re-crystallization orientation found in a copper strip previously cold-rolled 99.5 pct from a single crystal with an initial (110) [112] orientation may be described as: a 30° rotation, clockwise and counterclockwise, about octahedral poles of the cold-rolled texture such that all four poles function at a low annealing temperature (400°C) and only three of them function at high temperatures (500' to 1050°C). The relative intensity of deformation stresses on various slip planes can be correlated with the choice of poles affecting the rotations found in the recrystallized orientations. ROTATIONAL reorientation about the poles of densely packed crystallographic planes is an important characteristic of secondary recrystallization" in face-centered cubic metals. Some evidence has also been interpreted to show that such a rotational relationship also exists in the primary recrys-tallization process." In an investigation of the crystallographic relationships in the recrystallization process, several aspects of the experimental procedure should be considered. With cold-rolled poly-crystalline metal as the initial material, pole figure analysis leaves many ambiguities as to whether or not simple indices can be assigned to adequately represent its orientation. The rolling texture does not consist of a single texture. Minor deformation textures are usually present. In all cases, twin textures are present. The presence of both minor and twin deformation textures influences the recrystallization texture. In order to study the recrystallization mechanism, a more precise knowledge of the history of the material before recrystallization is necessary. Tensile deformation of a single crystal usually produces residual stresses which are concentrated at slip bands. Since the exact nature and orientation of these potential nuclei sites cannot be experimentally evaluated, the tensile deformation of a single crystal was not considered adequate. From the work done by Barrett and Steadman6 n copper, it appeared that cold rolling of a single-crystal specimen with an initial (110) [112] orientation would yield a specimen which fulfills the conditions required for the present investigation, namely a highly preferred single rolling texture with relatively homogeneous stress distribution. By investigating the recrystallization texture of this material, additional details of reorientation during recrystallization might be obtained. The purpose of this paper is to describe such an investigation. Experimental Procedure Copper used in the present investigation was cathode sheet with a purity of 99.94 to 99.97 pct. A copper single-crystal specimen, 1.15x0.8720x0.5322 in. (thickness) was cut from a cylindrical crystal which was grown in a Bridgman furnace.' The cutting was accomplished on a horizontal milling machine operated at a very slow speed to obtain a (110) plane in the rolling plane and a [112] direction in the rolling direction. The disturbed surface was removed by electrolytic polishing in dilute orthophos-phoric acid (H3PO4) with a specific gravity of 1.14, and a current density of about 1 to 2 amp per sq cm. A 3-min polishing was needed to eliminate the disturbed surface causing Debye-Scherrer rings and a 45-min polish produced a surface which yielded sharp rounded Laue spots. It was estimated that about 1/16 in. of metal was removed from the original cut surface. The final orientation of this specimen before rolling was about 2" from the (110) plane in the rolling plane with a [112] direction aligned in the rolling direction. It is possible that a small amount of strain was still present in the cube despite the fact that the Laue spots seemed very sharp. It is doubtful, however, that this would be an important factor after a subsequent rolling reduction of 99.5 pct. This copper specimen was rolled on a laboratory rolling mill with two highly polished rolls 37/8 in. in diam in the following manner: 0.010 in. per pass to 50 pct reduction, 0.005 in. to 70 pct, 0.002 in. to 85 pct and, finally, 0.001 in. per pass to a 99.5 pct reduction. Specimens, about 1 in. sq with the rolling edges intact, were cut from the rolled strip by the electrolytic method previously described, after the strip

Jan 1, 1954

By W. T. Turrall, M. J. Cook

A discussion of modern developments in beneficiation of fine sizes of anthracite, this paper includes a description of the plant flowsheet, an analysis of operating results, and a summary of fundamentals of mineral separation relative to plant operation.

Jan 9, 1953

By Cyril Stanley Smith, W. Earl Lindlief

A study of the mechanical properties of the alloys of copper and silver led to the discovery that the solubility of silver in copper was greatly different from that generally supposed, therefore some work was done to determine the solubility with greater accuracy than had previously been achieved. After the work had been completed, two papers were published' giving solubility figures which agreed closely with one another and with the work described herein. A detailed comparison of that work with the present will be given later. Preparation of Allots The copper used in making the alloys was electrolytic ingot of high purity. The silver was prepared by precipitation as chloride from nitric acid solution, followed by fusion of the washed precipitate with sodium carbonate and potassium nitrate. This method gives metal containing at least 99.99 per cent silver. The copper was first melted under charcoal in a small electric resistance furnace and the silver added as pure silver, it being unnecessary to make any intermediate alloys. After thorough stirring the metal was poured into a mold of suitable form. The alloys contained between 0.008 and 0.015 per cent of oxygen. Small amounts of oxide were visible under the microscope, but it is not believed this would have much effect on the results. Copper-silver alloys are notorious for segregation, consequently a few experiments were carried out to find a form of casting with as little segregation as possible. A mold 6 in. long and 1/2-in. dia. was first used, and an alloy nominally containing 5 per cent silver was cast in it, while some of the same alloy was poured directly into water to obtain the maximum rate of cooling possible. Analyses were made both on this sample and on turnings from the top and bottom of the 1/2 in. dia. cast-ing, the turnings being separated into three parts according to the position

Jan 1, 1932

By W. S. Morris, R. R. Bradenthaler, G. Wade

Petroleum engineers generally are of the opinion that the flow conditions and, therefore, the formulas that apply to the flow of oil and gas in long pipe lines differ in many ways from flow conditions in oil wells. One of the reasons why the formulas in common use for pipe-line flow do not correctly apply to oil wells is that the flow lines are vertical and not horizontal. Another factor to be considered is that the fluid is a mixture of oil and gas and that the physical characteristics of these two components are affected differently by changing conditions of pressure and temperature during upward flour. Realizing the need for accurate data on flow in vertical pipes under conditions caused both by natural flow and the gas-lift, the U. S: Bureau of Mines has installed equipment at the Petroleum Experiment Station, Bartlesville, Okla., for the purpose of studying this problem. In additon a study will be made of the comparative effects of different natural-flow and gas-lift methods of producing oil on ultimate production from reservoir sands. Experimental Equipment The experimental equipment consists of a regular oil-field steel derrick, a large pressure tank installed in a concrete pit beneath the derrick floor, compressors and pumps, gas separators and absorbers, metering and control devices, and the necessary pipe connections. The crown-block level represents the derrick floor at an oil well, and the "producing sand" is the pressure tank below the derrick floor. The difference in elevation between the crown-block level and the tank is 90 ft. Figs. 1, 2 and 3 show the construction and exterior arrangement of the equipment. The success of the experiment will of course depend largely upon the accuracy of the oil and gas measurements and the temperature and pressure determinations. Because extreme accuracy is necessary, all oil and gas measurements will be checked at least twice, and in some

Jan 1, 1929

By N. K. Chen, R. Maddin

Single crystals of molybdenum were extended at temperatures from 1300° to 2500°C. It was found that with increasing temperatures, the yield becomes more pronounced and the number of slip bands for equal amounts of elongation decreases. Slip at high temperatures fragments the structure. OTHER than the investigations on sodium and potassium by Andrade and Tsien,&apos; the researches of Steijn and Brick&apos; on a iron single crystals at low temperatures are about the only studies of the influence of temperature on glide of body-centered cubic single crystals. The effect of test temperature on glide has been rather widely investigated with hexagonal crystals" and less widely with face-centered cubic crystals. ~~ a result of these studies it can be said that, in general, the onset of plastic flow as measured by the initial rate of strain hardening becomes more abrupt with increasing temperature, and the value of the yield decreases with increasing temperature. Strain hardening, however, is markedly affected by changes in temperature except at very low and very high temperatures where the strain hardening rate becames constant. In the present investigation it is shown that temperature affects the glide of molybdenum single crystals in much the same manner as crystals of other classes, it., for comparable strains the number of slip bands decreases with increasing temperature; shear along the slip bands increases with increasing temperature; the yield becomes more pronounced with increasing temperature of test; and the strain hardening approaches a constant at very high temperatures. In addition, it is shown that, in agreement with the work of Tsien and Chow, Qlip occurs on (110) planes in <Ill> directions. It is further shown that slip at high temperatures fragments the structure into either irregular sized cells or bent atomic planes which are roughly aligned in crystallographic directions. Experimental Procedure Single crystals 3 mm in diameter by about 25 mm long were prepared using the technique previously described.&apos; The furnace in which the crystals were grown served as the extension apparatus for the tension tests. It consisted of a 4 in. water-cooled brass tube 20 in. long which was continuously evacuated at the bottom. Two water-cooled copper electrodes held the specimen by means of spherical collets secured in place in the electrodes by set screws. These electrodes served also to transmit power and stress to the specimen. The lower electrode was clamped to a stand, while the upper electrode was fastened to one side of a lever arm flexibly supported at the top through a slightly offset pinion. A metal bellows operating elastically was attached to the upper electrode to affect a vacuum seal and allow freedom of motion. The level of the arm was adjusted by rotating a graduated nut. Rotation of the electrode was prevented by a key fitted into a groove. After the specimen was mounted and the vacuum secured, the lever arm was adjusted so that the bellows was at its relaxed position. This insured that the total weight of the specimen, the upper electrode, and the downpull of the vacuum were balanced by the horizontal beam. Since the specimen was heated by its own resistance, expansion of the specimen proceeded freely by this arrangement. During the time of heating the specimen, the beam was maintained in a horizontal position by turning the nut at the top. By graduating the lever arm and using a known dead weight on the lever arm to supply a tensile stress, the graduated nut could be read to 0.0001 in. extension. Since

Jan 1, 1955

By B. Ball, D. W. Fuerstenau, P. C. Kapur

A two-phase distributed-parameter model of the flotation process has been extended to allow consideration of the important process parameter, concentrate grade. A simple expression is presented for the grade of concentrate in terms of the zeroth and first moments of the concentrate distribution. An example is given for a binary ore containing two pure minerals each having nondistributed rate constants. For extend-ing the model to the distributed rate constant case, a cubic polynomial zoas utilized to simulate the feed distribution. One particular example is considered and grade-recovery curves are generated to show the dependence of such curves on the initial feed distribution. Operating flotation plant engineers have traditionally evaluated plant performance in terms of the recovery of valuable mineral and the grade of the concentrate. In both operation and research, grade-recovery relationships have been used as a guide for selecting flotation conditions. Weissl illustrated the use of grade-recovery curves in plant operation and considered the grade-recovery relationship to be a metallurgical one. The extensive experimental work of Chi" using standard batch flotation tests on iron ores shows that, even with extensive statistical correlation of data, little insight can be gained into the basic fundamentals of these relations. Such relations must depend on the kinetic behavior of the various mineral species in the flotation circuit. In his flotation text book, Gaudin3 considered the relationship of recovery and of product grade to flotation kinetic indices, but he did not extend his calculations to yield grade-recovery relations. Although Gaudin used a simplistic model for his analysis, he did recognize that variations in flotation rates must result from variations in locking, surface heterogeneity, particle size and shape, among other things. In a recent paper,&apos; we presented a model of the flotation process that could be readily analyzed with an analog computer. This model combines the concept of a distributed set of rate constants"" with that of the two-phase flotation model,8" resulting in a model more powerful and flexible than previous ones. The purpose of the present paper is to show how this model can be used to generate grade-recovery curves and to determine the dependence of such curves on the various kinetic parameters. In this paper, the model will be limited to the semi-batch case, but extension to the continuous case is a straightforward step.

Jan 1, 1971

By W. S. Hyler, W. L. Bruckart

The powder metallurgy and arc-cast types of wrought molybdenum stock were studied in rotating beam fatigue. Endurance ratios of unnotched specimens after 5x10 cycles were found to be 0.74 and 0.81, respectively. Fatigue notch factors (K,) of 1.36 and 2.05, respectively, were obtained on V-notched specimens having a theoretical stress-concentration factor Kt = 3.1. MOLYBDENUM and its alloys are rapidly gaining importance as engineering materials of construction for high temperature applications. AS a wrought material, molybdenum and its alloys are outstanding above 1800°F. It is necessary, however, with molybdenum to provide elevated temperature oxidation protection. This is currently being studied by a number of investigators. Thus far, there have been no published data on the fatigue behavior of molybdenum either at room temperature or at elevated temperature. The knowledge of fatigue behavior, particularly notched fatigue behavior, becomes increasingly important as the engineering importance of a material increases, especially from the design standpoint. The work described here was directed toward determination of the notched and unnotched rotating beam fatigue characteristics of molybdenum at room temperature. Also, it was desired to learn whether any difference exists between wrought molybdenum of the powder metallurgy and the are-cast types. Fabrication History of Bar Stock For this work, bar stock was procured from Climax Molybdenum Co. (are-cast type) and from Westing-house Electric Corp. (powder metallurgy type). The processing histories of these materials are listed in Table I. The first lot of are-cast molybdenum was deoxidized by aluminum additions. The second lot was deoxidized by carbon." Both lots of the powder Microstructure A microscopic examination of these materials, as received, revealed the powder metallurgy molybdenum to be free of inclusions and to be finely fibered. On the other hand, the are-cast C molybdenum possessed numerous carbide inclusions, and the arc-cast A appeared to have coarse grained fibers. These are shown in Fig. 1. Owing to the large apparent difference in fineness of fiber between the are-cast A and the powder product and are-cast C, a check was made of the recrystallized grain sizes to determine whether these differences persisted. A series of recrystallization anneals revealed mixed grain sizes in both the are-cast A and the powder product. Variations in grain diameter of as much as 50 times were found after full recrystallization at 1200°C for 30 min. There was no distinction between the two. Arc-cast C was not checked. Room Temperature Mechanical Properties Prior to subjecting the materials to fatigue tests, room temperature mechanical properties were determined. These data, together with the tensil: strength of the notched bars, data,togetherare listed in Table tensil: There were no significant differences in the tensile strengths of the two types of molybdenum. However, the powder metallurgy material was generally more ductile and yielded at a somewhat lower stress than the arc-cast material. Tensile strengths of the notched specimens indicated a slightly greater notch strengthening effect in the are-cast C than in the powder product, lot 2. Room Temperature Fatigue Properties Sample Preparation: Specimens were prepared for use in R. R. Moore rotating beam fatigue machines. These specimens had a continuous radius test section with a minimum diameter of 0.260 in. The specimens were prepared by grinding to shape and polishing to produce a smooth unworked surface. Polishing consisted of rotating a disk in the continuous radius section on which were attached, successively, emery belts of 240, 400, and 600 grit. The specimens were slowly rotated during the operation. The belt speed was high, and rotation was such that polishing scratches were longitudinal. Unnotched Fatigue Properties: Unnotched fatigue data were obtained from a number of specimens of each of the four lots of molybdenum. The results of the tests are presented in Fig. 2. From this figure,

Jan 1, 1956

By M. E. de Morton

Recovery and early recrystallization of heavily deformed, 99.98 pct Cr was investigated by studying metallographic structure. X-ray line sharpening, electrical resistivity, plastic properties, internal friction, and shear modulus. Appreciable recovery of resistivity, internal friction, and shear modulus together with some hardening and relief of internal strains occurred before the visible growth of a textured substructure above 350°C (recrystallization in situ). The complex behavior of shear modulus, internal friction, and its strain amplitude dependence during annealing are discussed qualitatively in terms of the relative mobility of dislocations. BY plastically deforming fully recrystallized 99.98 pct Cr above the brittle to ductile transition temperature, at -350°C. as in wire drawing, chromium can be made very ductile at room temperature. However, this ductility is lost on annealing at high temperatures when recrystallization takes place.&apos; The present investigation was made to determine the general pattern of the changes in a number of physical and mechanical properties during recovery and recrystallization of heavily deformed chromium as part of an effort to elucidate the reasons for lack of ductility in the fully recrystallized condition. PREPARATION OF MATERIAL Wire specimens 0.027 in. in diam were prepared from arc-melted, electrolytic chromium by extruding, hot swaging and finally wire drawing at 300" to 350°C, i.e. above the brittle-to-ductile transition temperature. The total reduction in area of the wire was 98 pct and the last 3 pct of reduction was made at 100" to 150°C before cooling to room temperature. The impurity content of the material is shown in Table I. Internal friction and modulus measurements were made on a single specimen after annealing in situ at successively higher temperatures. For all other measurements, a fresh specimen was used for each temperature and annealing of these specimens was done in evacuated (0.001 mm Hg) and sealed silica tubes for 1 hr at the various temperatures up to 700°C. EXPERIMENTAL METHODS AND RESULTS The occurrence of a. transition in some physical properties of chromium at - 40°C2 imposed limitations on the temperature region where some of the measurements could be made. The reason for this transition in chromium is at present unknown but is probably associated with an antiferromagnetic state observed below - 40°C.* Heavy deformation produces an anomalous decrease in resistivity when measured at temperatures below -40°C4 though a normal increase is observed above this temperature. On the other hand internal friction in heavily deformed chromium5 over the temperature range 40" to 50°C is invariant with temperature. Above and below this range internal friction is strongly temperature dependent, increasing with increasing temperature. A temperature in this range was therefore convenient for both resistivity and internal friction measurements and for consistency the measurements of the mechanical properties were also made at about this temperature. No structural change has, however, been observed in careful X-ray measurements6 between -195" and 50°C, i.e. departure from cubic symmetry was not greater than 3:10,000; X-ray line sharpening measurements were therefore more conveniently made at room temperature.

Jan 1, 1962

By Blake M. Caldwell, Harrold D. Owen

The continued use of permanent-type, we11 completion Iras pointed LIP the need for more powerful through-tubing perforating equipment. A new expendable shaped charge perforator has been developed in which the charges are run through the tubing in a vertical position and then opened out to a horizontal position when at the desired shooting zone. The performance of this new tool is comparable to that of conventional casing type perforators. This paper describes the new tool and its applications. Performance data in targets rind under various actual well conditions are presented. INTRODUCTION The general acceptance and increasing use of pernianent-type well completion by the oil industry has indicated the need for through-tubing perforating equipment with performance comparable to that of conventional casing type perforators.&apos;.&apos; To achieve the performance desired, a new, expendable, shaped charge perforator has been developed with adequate power for effectively perforating both 51/2-in. and 7-in. casing below tubing. This has been accomplished without resulting severe damage to the casing and can he obtained under extremes of pressure and temperature. The design of this new tool is a radical departure from previous concepts of tubing guns since it was felt that the two major limitations imposed by previous designs severely handicapped performance. The first of these limitations was the restriction imposed upon the length of the charges by the necessary small inside diameter of the carrier. This resulted from the necessity for compromises in designing a hermetically sealed gun small enough to allow free passage through 2-in. tubing, yet with sufficient wall thickness to withstand some minimum pressure. In an effort to overcome this limitation, the charges were in some cases placed at an angle with the axis of the well with resulting loss in effective depth of penetration. The second limitation concerned the extreme distance of the charges from the casing when the gun was fired. An example of the latter situation is demonstrated by the fact that a conventional 13/4-in. tubing gun centralized in 51/2-in., 17-lb casing has a clearance of more than 1-9/16-in. on all sides. This means that a considerable portion of the force from each charge must be expended in penetrating this 1-9/16-in. of well fluid before it even reaches the casing. With the gun centered in 7-in., 23-lb casing, the amount of fluid penetration required of each jet is in excess of 21/4-in. In a situation where the 13/4-in. gun is touching one side of the 51/2-in., 17-lb casing, the jets from the charges on the opposite side have more than 3%-in. of fluid to penetrate. A similar situation in 7-in., 23-lb casing necessitates the penetration of more than 4-9/16-in. of fluid. The penetrating effect of the charges is severely impaired in passing through so much fluid. Under such conditions, there is usually insufficient force left to penetrate the casing. Previous studies have shown the decided disadvantage of having to shoot through such an excessive quantity of well fluid.&apos;.&apos; The problem. then, was how to position large powerful charges close to the casing prior to firing and still manage free passage through 2-in, tubing. The solution appeared to be in some method of folding sealed charge units in an open type, expendable. 13/4-in. carrier for travel through the tubing, and unfolding them upon their arrival at the shooting zone in the casing. It was desired to control the mechanism electrically from the surface through the regular shooting cable, making the release of the charges independent of the physical characteristics of the well, yet with a provision to prevent the gun from firing until the

Jan 1, 1955

By J. W. Pamplin

Some 40 miles east of Tampa is the center of the Florida pebble phosphate deposits. These are of Pliocene age and consist of several members of the Bone Valley formation.1 Physically the phosphate-bearing formation, locally called the "matrix," varies in thickness from nothing to about 25 ft., usually averages 10 ft., and consists mainly of clay, quartz and phosphate pebble, the latter particles varying in size from colloidal to one inch diameter. The pebbles range in color from dark gray, through white, to cream, and in hardness from that which must be broken with a hammer to that which can be scratched with the fingernail. They assay from 66 to 80 per cent bone phosphate of lime (called "B.P.L." in the trade) or tricalcium phosphate (Ca³P2O8) and are secondary apatites. They form from 15 to 50 per cent by weight of the matrix. Over the matrix lies a varying thickness (5 to 40 ft.) of overburden composed of quartz and clay. Briefly, mining consists of two operations2 in open pits about 200 ft. wide by 1/2 mile or more in length. In the first step overburden is removed by large electric draglines at the rate of about 700 cu. yd. per hour. This is followed closely by hydraulic mining of the matrix at the rate of about 300 cu. yd. per hour. This matrix yardage is moved from an improvised sump in the floor of the pit to an ore-dressing plant, sometimes a mile distant, by one, two or three "pit-cars" (pumping units) working on a 12-in. pipe line called the "rock line" to distinguish it from the high-pressure water line feeding the hydraulic giants, which is known as the "hydraulic line." This 700 yd. of overburden and 300 yd. of matrix—1000 yd. in all-amounts to about 1500 tons of material moved each hour. The overburden is dumped into the mined-out pit alongside the pit being mined. The matrix moves to the ore-dressing plant at the rate of about 7% long tons in 4000 gal. of water per minute—a ratio of approximately one to two by weight, or one to six by volume. This constitutes the "mill heads," but in the pebble district it is called the "matrix."

Jan 1, 1938

By O. B. Ellis

Although thousands of tons of stainless steel have been used successfully for many types of equipment, there have been few cases of failures due to the phenomenon described as stress corrosion cracking. During the past seven years only six cases of such failures have been drawn to our attention and investigated in the Research Laboratories with which the author is associated. These failures oc¬curred in two coffee urns, two wool con¬ditioning units, one dyeing machine, and another in a part of a steam-jacketed stock pot. In each case the equipment failed in a comparatively short time after exposure to conditions of high humidity at tempera¬tures in the range of 100 to 200 F. The failures in all cases were characterized by general embrittlement and cracking of the stainless steel, with only slight indications of general corrosion except at the cracks. The first failure of this type was a coffee urn returned for investigation in 1937. The top and bottom sections showed a general corrosive attack and embrittlement and cracking of the stainless steel. The chemical analyses of these sections were as follows:

Jan 1, 1945

By H. Carroll Weed

By caving a block into the workings of its open pit and using the block as an ore transfer, the lnspiration Consolidated Copper Co. has solved a transportation and sizing problem, making possible a great expansion of open-pit methods as applied to Inspiration ore-bodies. FROM 1915 to 1948 the entire production of Inspiration Consolidated Copper Co. was supplied from underground mining. The sole method used was block caving. Underground haulage and hoisting facilities were designed and geared to large-scale production. Beginning in 1948 open-pit mining was substituted for block caving in a portion of Inspiration&apos;s Live Oak orebody. The idea proved so attractive that before the Live Oak pit had come into production, another pit on the Colorado orebody (now the Thornton pit) had been laid out and stripping started. It should be noted that these orebodies were not new and the entire program was one of changed methods of mining. Since part of these orebodies had already been mined by block caving methods, it must be recognized that haulage levels had been established under the area or adjacent to it. The orebodies lay on the south side of Inspiration Ridge, while the shafts, crushers, and treatment plants are all on the north side of this ridge. The existing main crushing plant was designed to take a maximum of 12-in. material, and all ore was sized to this dimension by passing through grizzlies in the stopes. In the original planning for open-pit work much thought was given to the transfer of ore to existing underground levels for haulage and hoisting from the regular shafts. If this could be done the necessity of crossing the ridge could be eliminated. Final decision called for cutting a road through the ridge, installation of a primary crusher at an elevation of 3968 ft on the north side of the ridge, and railroad haulage with existing facilities to the main coarse crusher. This decision was brought about by the difficulties of properly sizing and transferring to underground haulage large tonnages of coarse breaking oxide which lay on the upper benches of the proposed pit. Trucking over the ridge on a 7 pct grade would give a cheaper and more flexible operation in handling this material. The benches in the pits are laid out at 50-ft inter-vals and designated according to elevation above sea level. The lowest bench in the original pit was laid out at 3500-ft elvation. All haulage roads are on a 7 pct grade and a vertical lift of 468 ft was considered about the maximum economically possible from a cost standpoint. After 2 years&apos; operation the advantages of pit mining, both from the standpoint of costs and flexibility of operation, became more and more apparent. Studies were then started to develop the extension of open-pit mining to more of the ore reserve than had been planned originally. The idea of transfer raises was again explored. Obviously, as elevation of the pit was lowered, shorter transfer raises would be needed to reach the main haulage levels. Transportation from the lower elevations to the rim of the pit by belt conveyor or skip hoisting was also considered. However, it was recognized that sizing would be required both for conveying and regulation of feed size to the main crusher plant. This would necessitate a fixed or portable crusher located somewhere in the pit. It was known that the sulphide ore at the lower elevations was softer and easier to break than the overlying oxide of the upper benches. This sulphide ore is very suitable for grizzly sizing. Calculations indicated that for ore mined on 3650 elevation, costs for trucking to the primary crusher, crushing, and delivery by railroad to the coarse crusher would equal costs for dropping the same material to the 600 level, hauling underground, and hoisting directly to the coarse crusher bins, provided a suitable method of sizing and transferring could be developed. Above 3650 elevation costs would favor surface haulage; below they would favor underground haulage. The idea of caving an underground block from the 600 haulage level directly into the bottom of the pit

Jan 1, 1954

By A. E. Dwight, A. F. Berndt

Binary and ternary alloys of uranium with transition metals were prepared with U2X stoichiometry. The compounds U2Tc, U2Rh, U2Os, and U2lr were formed by peritectic or peritectoid transformations, and were shown to be isostructural with U2Ru. The lattice constants are presented. Miscibility relationships obtained from the study of ternary alloys are graphically summarized in terms of an area-of-stability plot. The compound U2Re is not isostructural with either U2Ru or U2Mo. A series of compounds with stoichiometry U2X has been prepared in which X is technetium, rhodium, rhenium, osmium, or iridium. The only other U2X compounds, for which X is related to the above transition metals by proximity in the periodic table, are U2Mo and U2Ru. The structure of U2Mo is the tetragonal C11b type (MoSi2 type)1 and U2Ru is monoclinic, with a new structure type.&apos; This investigation was undertaken to determine if any of the above compounds are isostructural with either U2Ru or U2Mo and to find the range of occurrence of these phases. EXPERIMENTAL Alloys were prepared from stoichiometric amounts of electrolytic uranium (99.99 pet pure) and transition metals of 99.5 pet purity (98+ pet pure Tc), by arc melting on a water-cooled copper hearth under an Ar-He atmosphere. Weight losses were negligible. The buttons were homogenized at temperatures between 700o and 800°C (900°C for U2Tc) in evacuated capsules and air-cooled. The X-ray powder specimens were annealed briefly at the temperature of homogenization. Except in the case of the technetium alloy, metallographic examination was used to determine the number of phases present. The radiation hazard involved in handling technetium precluded the use of metallography to examine U2Tc. The temperature and mode of formation of the U2X phases were determined by heating the metallographic specimens to successively higher temperatures, until examination indicated the presence of chilled liquid or a peritectoid transformation. RESULTS The U2X compounds investigated were found to be formed under the following conditions: UzTc unknown U2Ru peritectic 897o ± 3°C U2Rh peritectoid 755o ± 5°C U2Re peritectoid3 below 750°C Uas peritectic4 920°C U2Ir peritectoid 775o ± 5oC Debye-Scherrer patterns for the above U2X phases were made with CuKa radiation (nickel filter). The similarities in the positions and intensities of the strongest lines in the front-reflection region strongly suggested that U2Tc, U2Ru, U2Rh, U2Os, and U21r are isostructural with only minor differences in the unit-cell dimensions. The known lattice constants and intensities of the Debye-Scherrer rings for U2RU2 were used as a guide in order to index the low-angle X-ray reflections of the U2TC, U2Rh, U2Os, and U2Ir powder patterns. Approximate lattice constants for these compounds were thus obtained and were used along with the intensities observed for U2Ru to index the strongest lines in the back-reflection regions. A sin2 2? correction term was included and the lattice constants were refined and standard deviations estimated by least squares. Comparison of observed and calculated values of Q(= 4 sin2?/?2) used in these calculations are given in Table I. In each case when the positions of lines could not be resolved on the films they were not measured. The final lattice constants, with their standard deviations, are given in Table 11, along with the unit-cell volume and X-ray density. The values of the atomic volume5 of the transition ele-

Jan 1, 1965