Search Documents

By B. Woyski

Many writers, in discussing defects caused by oxidation and gassing of bronzes and red brasses advocate substantially the same cure for both. But from its nature, oxidation cannot take place if there is an excess of fuel in the furnace, while the gases absorbed by some alloys are products of incomplete combustion of the fuel. Hence the metal can be either oxidized or gassed, but it is doubtful whether these actions can take place simultaneously. Oxidation can be easily overcome by the use of deosidizers or it may be avoided by protecting the molten metal with suitable fluxes. Absorption of gascs is more difficult to overcome: the regulation of the air and fuel, so as to produce complete combustion, and the protection of the bath by mineral fluxes arc the most important factors. Gas expulsion, resulting in gas holes, porosity, unsoundness, and swollen or cauliflower-headed risers, is said to have several causes. One writer1 lists the most common causes in the order of their importance, as follows: Superheated metal, dirty or slaggy furnace conditions, using metals low in quality or those previously subjected to bad melting practice, poor grade of fuel, use of newly lined or damp ladles, indiscriminate mixing of scrap or illogical combinations of metal. Superheating the metal usually occurs when the heat is ready to be poured but for some reason must be held in the furnace. In this case, a careful furnace tender tries to avoid overheating the metal by keeping a mild fire; that is, a reducing fire which, unfortunately, results in gassing the metal. A dirty, slaggy furnace may result in gassing the metal by retarding the heating and prolonging the time necessary to bring the metal to the proper temperature, thereby increasing the chances of gassing in uncertain furnace atmosphere. It is doubtful whether rnetals of low quality have anything to do with gassing molten metal, except, possibly in the case of metals containing

Jan 1, 1923

By P. J. G. duToit

The continually growing shortage of skilled underground miners, the escalating costs of labor, supplies and equipment, and the indisputable example of "what can be done" by our friends in the space-travel field, seem to be catalysts that are accelerating improvements in underground mining technology. The search for an economic, automated continuous excavation method that would produce rock at the mining face in sizes suitable for automated transportation directly into the rod-, ball-, or autogenous grinding mills is continuing. New mining methods and techniques were devised and many improvements on old methods and techniques came forth at an increasing pace that reflected a widely spreading policy among mining men to shun the shackles of conservatism and to forge ahead and venture into newer ideas.

Jan 2, 1967

By P. H. Dudley

The present paper was suggested by the paper read by Mr. R. W. Hunt at the New York Meeting, in February last, on rail-sections (Trans., xvii., p. 778)) in the discussion of which I brought forward some of the facts and observations here stated. Professional duties having prevented me from writing out my part of that discussion in time for its publication in the volume containing Mr. Hunt's paper, I take the opportunity to present it in separate form and greater fulness. The striking features of the series of rail-sections submitted by Mr. Hunt are their shallow heads and heavy bases. In these respects they are quite similar to the section of the 80-1b. rail, which I designed in 1883 to meet the requirements of the traffic of the New York Central and Hudson River Railroad. Before the adoption of the 80-1b. rail, this road had modified its 65-1b. section from a shallow head with rounding sides and quite heavy base to one having a deep head and thin base. All the leading railroads had changed from the earlier sections of steel rails to those having deep heads and thin bases, conforming to the recommendations of the Committee on Rails of the American Society of Civil Engineers. It is but proper to say that the committee's investigations upon the wear of rails were made upon the rails manufactured under a practice quite different from that which obtained after the committee's recommendations were carried into effect. The results in actual service have been contrary to what was expected. Fig. 1 shows my 80-1b. section of 1883. Before designing this rail I had taken, at different times, a series of diagrams of the condition of tracks, with my car, on the New York Central and Hudson River Railroad, all of the New England railroads, and all but one of the trunk lines. My diagrams gave me an opportunity which could not otherwise have been obtained to see the wear of great numbers of sections of rails under widely varying conditions of traffic.

Jan 1, 1890

By J. Gordon Parr, D. H. Polonis

High purity alloys of titanium and iron, made by a technique of levitation melting, have been investigated with particular reference to martensite formation and decomposition in the hypoeutectoid range. A preliminary study has been made of the occurrence of the phase corresponding to the structure Ti2Fe. MANY of the previous investigations of Fe-Ti alloys have been made using Kroll sponge as a source of titanium; and the subsequent heat treatments to which alloys have been subjected has, on occasion, led to further contamination. Worrier,',' who suggested a part of the equilibrium diagram for the binary system, and Wallbaum and coworkers,3-5 who worked largely with iron-rich alloys, all used Kroll sponge. Van Thyne, Kessler, and Hansen,6 in their determination of the equilibrium diagram, used iodide titanium for alloys up to 30 pct Fe. Duwez,7 who measured the M. temperature of titanium binary alloys with many solute elements, used iodide titanium in all cases except in his work on Ti-Fe alloys for which he used Kroll sponge. The investigation of the supposed phase Ti2Fe by Rostoker8 nvolved the use of iodide titanium. A section of the constitutional diagram, after Van Thyne et al., is reproduced in Fig. 1. Frequently too much stress is placed on the effect of contaminants in equilibrium and nonequilibrium systems, but there is no doubt that titanium alloys are extremely susceptible to interstitial atoms. Consequently, the main purpose of the work to be described was to determine those features of phase transformations in pure Ti-Fe alloys that were considered of importance in commercial heat treatments. For, although commercial alloys may not be of high purity, the investigation of a system uncomplicated by traces of impurity is a desirable starting point. Another incidental feature, the occurrence of Ti2Fe, was also investigated. The entire study was carried out using powders obtained from alloy ingots, for diffusion reactions are often more rapid in small particles than in bulk specimens. The frequently adopted practice of ascertaining phase constitutions by X-ray analysis of powders, and relating these to the microstructures and mechanical properties of bulk specimens, is considered by the authors to be open to criticism. In the martensite reactions in the Fe-Mn system, for example, it has been shown- hat similar phase distributions in solid and powder may result in different hardness values and appearance under the microscope; and it is possible that similar anomalies might occur in the Ti-Fe system. Consequently, in order to

Jan 1, 1955

By Charles Russell

PRESSURES developed by the coal during the coking process have been responsible for serious trouble to many companies that operate or build by-product coke ovens. The insidious nature of this trouble is indicated by the fact that oven operators, unless they have ascertained the charac-teristics of the coals they use, cannot determine the existence of dangerous pressures until after the damage has been done. A rather popular mis-conception is that ease of pushing of the charge at the completion of the coking period indicates that no dangerous pressure has been developed, but this is far from the truth; pressures developed during the coking period are often completely dissipated by the shrinkage of the charge in the completion of coking, and so any criterion based on the ease of pushing is futile. However, methods of testing coals are available that will definitely distinguish the dangerous coals from those that are safe, and such methods have been brought to a high degree of certainty. The operator should take no risk that involves either a lack of knowl-edge of the behavior of coals during coking or the failure to believe that certain of the coals or coal mixtures can cause damage to the oven struc-ture. This merely tends to minimize the problem and leads to claims that coking coals of all kinds may be carbonized with no danger of damage to the oven structure provided some particular kind of by-product oven is used. This lack of appreciation of the true situation is in itself one of the main factors leading to damage of coke-oven structures. Coals that develop more than a certain safe pressure cannot be used in by-product coke ovens without causing damage to the side flue walls. The following paper presents a highly certain method for the measure-ment of the pressures developed during the carbonization of coal-a method that is the culmination of many years of work on the problem in which a number of methods for the purpose were investigated and used. While actual pressures found may appear to be small when expressed in pounds per square inch, the number of square inches in each oven wall is so large that the total pressure on the oven wall becomes an enormous load.

Jan 1, 1939

By W. E. Rice

The ceramic industry has to do with forming or molding articles of clay, and imparting to them their characteristic properties of permanence, strength and color by subjecting them to heat treatment in kilns. This heat treatment is commonly known as "firing" or "burning." The art of firing clay ware antedates the industrial use of coal; hence wood was the fuel first used, and the earliest kilns were built to burn wood. The majority of the clay ware produced today is fired in periodic kilns that are essentially enlarged structures similar to the earliest enclosed kilns; a kiln consists of a large chamber 16 to 32 ft. dia. (or rectangular) in which the ware is charged and fired either in direct contact with flame or hot gases from the fuel, or in saggers which shield the ware from direct contact with the gases. The fuel is burned in a number of small furnaces built in the thick wall that encloses the chamber; these furnaces are from 16 to 36 in. wide and from 3 to 5 ft. long; some of them have horizontal or sloping grates, but many have no grates; the last are called "dead-bottom" furnaces. The temperature necessary to mature the charge in the kiln varies for different clays; for some it is as low as 1800°, and for others as high as 2700" F. Wood was an ideal fuel for the low temperatures that were used in early kilns; it burns freely and produces a long, clean flame, which promotes uniform distribution of the heat in the kiln; it does not coke and so restrict the passage of air through the fuel bed; the ash does not melt in the fuel bed to form clinker; and the ash that is carried into the chamber and deposited on the charge does not contain iron and sulfur to discolor the clay. The extent of the ceramic industry now precludes the general use of wood in kilns, so that today this industry is one of the large users of bituminous coal, burning more than eight million tons annually in kilns. Manufacturing plants usually are at or near the source of clay, with deposits of coal suitable for kilns occurring near the clay. The cost of coal is the largest single item of expense in the manufacture of clay ware, and, because all coals are not equally suitable for the process, the careful selection of coal is important. In this selection the desidera-

Jan 1, 1932

By Karl Sundberg

ELECTRICAL investigations carried out in regions containing sedimen-tary rocks showed that sediments generally are good electrical conductors, a fact which at the present time is used for structural investigations by electrical methods. It is of fundamental importance, not only for these investigations but also for electrical prospecting in general, to know the electrical properties of various soils and rocks. It will be useful, there-fore, to discuss this question with the hope that the general points of view discussed in this paper will perhaps be, completed by further observations and determinations of material from various localities. This paper is based principally on the study of literature, and the purpose is primarily a discussion of the main factors that determine the electrical conductivity of soils and rocks. It will follow, however, that the factors discussed here also frequently decide how far a certain orebody can be regarded as a good electrical conductor compared with the sur-rounding rocks. All-rocks are more or less porous; and the pores are filled with liquids and gases. Their electrical conductivity, therefore, depends on the following factors: 1. The electrical conductivity of minerals composing the rock. 2. Electrical conductivity of the liquid filling the pores. 3. Proportion of the volume of liquid filling pores of the rocks to the solid rock material. 4. Shape of the pores. 5. Arrangement of the particles of gas and liquids. 6. Temperature. Dry minerals, with the exception of certain ore minerals, are complete nonconductors from the point of view of applied geophysics; in the present investigation we deal with rocks which have no conducting minerals, and factor 1, therefore, is not important. The same is true of soils. The liquids contained in soils and rocks in most cases are waters, some-times oil. As oil is a nonconductor of electricity, the impregnating waters will determine the electrical conductivity of soils and rocks.

Jan 1, 1932

By Edgar C. Bain

Of the important phenomenon of the hardening of steel, Professor Sauveurl says: It would seem as if the methods used to date for the elucidation of this complex problem have yielded all they are capable of yielding and that further straining of these methods will only serve to confuse the issue, the point having been reached when this juggling, no matter how skilfully done, with allotropy, solid solutions, and strains is causing weariness without advancing the solution of the problem. The tendency of late has been to abandon the safer road of experimental facts and to enter the maze of excessive speculations, in which there is great danger of some becoming hopelessly lost. The conclusion seems warranted that new avenues of approach must be found if we are to obtain a correct answer to this apparent enigma. With some degree of fitness we may say this of other problems. It seems likely that one of the new avenues of approach to many metallo-graphic problems is the study of crystal structure, or more accurately, the atomic arrangement, by means of the x-ray spectrometer. The crystal structure of some materials has been carefully worked out by the mineralogist, but his methods are, in general, unsuited to commercial metals and a method that yields even better information is at hand as the result of work on the diffraction of x-rays by Laue and the Braggs2 and later by HullI3 St. John, and others. It should be understood that the contour of free crystals, which is the subject of measurements by the crystallographer, is the result of the atomic structure and, in general, bears a simple and obvious relation to it. The use of the x-ray spectrometer4 has been described frequently, so the procedure will not be given here.

Jan 1, 1923

By Louis Huber

DESPITE the fact that centrifugal fans were first developed for ventilating mines and that artificial ventilation was first practiced in mines, the lack of knowledge of mining men on mine ventilation in general, and on fan performances and characteristics in particular, is very much in evidence today. While it is true that mines are much better ventilated now than they were 20 to 30 years ago, we have made very little progress in the study of mine ventilation, or in mine ventilating fan design. Today the average mine operator is woefully dependent on the engineers of mine fan manufacturers when he is in the market for a fan, and this situation works to the disadvantage of both the operator and the manufacturer. The former may be imposed upon by an unscrupulous sales engineer and induced to buy a fan which is not the proper one for the mine; when it is operating it may be wasteful of power and even accessory to a serious mine disaster. More often, however, it is the fan manufacturer who is imposed on. If the operator asks the manufacturer to build for him a fan that will deliver a certain quantity of air against a certain specified pressure and requiring a specified number of horse power when operating under these conditions, the manufacturer may build a fan that will comply with these specifications to the letter. When the fan is installed it is frequently found that it is delivering a greater quantity of air against a lesser pressure or a lesser quantity of air against a greater pressure, and is requiring more horse power than specified in the first case and less than that specified in the second. In either case the operator usually upbraids the manufacturer for not meeting specifications, and refuses to pay for the fan. The trouble in either case outlined above is that the pressure necessary to force the specified quantity of air through the mine has been estimated incorrectly by the operator or his engineers. When a fan is designed and built to deliver a certain quantity of air against a certain specified resistance it will operate at its maximum efficiency only when it is operating under

Jan 2, 1926

By Paul A. Farrar, Felix Ermains, Harold Margolin

The systems Ti-Crand Ti-Vhave been reinvesti-gated in the region up to 40 wt pct alloying addition using both conventional and rapid quenching techniques. The Ti-Cr eutectoid temperature was determined to be at 667° & 10° C and 14.5 wt pct Cr. The solubility of the Cr in a Ti was found to be less than 1 pctat 700"C. The P transus of the Ti-V system was found to be depressed to 510°C at 40 wt pct V and the solubility of V in a Ti was found to be less than 2 wt pct at 700°C. Investigation by a. d. McQuillan1-3and m. k. McQuillan4 on the systems Ti-Co, Ti-Cr, Ti-Cu, Ti-Fe, Ti-Mn, Ti-Ni, and Ti-V has cast doubt as to the position of the ß/a + ß boundaries in many of these systems. Their investigations were carried out using hydrogen pressure and/or rapid quenching experiments, as opposed to the conventional quartz capsule techniques employed by most other investigator.'" By these methods, the ß/a + ß boundary was found to be lower than that obtained by conventional techniques in all except the Ti-Fe system. In the latter, the ß/a + ß boundary was essentially the same as the boundary obtained by conventional technique.7' On the basis of rapid quenching results in the Ti-Cr system, M. K. McQuillan4 placed the eutectoid temperature below 550°C whereas other investigations using conventional techniques had placed the eutectoid variously as between 650' and 700°C,5 between 675' and 700°C,6 between 650" and 675°C,7 at 670°C,8 and above 625"C.la9l3 In order to check these results, a reinvestigation of four of the systems was undertaken using both conventional and rapid-quenching techniques. The Ti-Fe and Ti-Mn systems will be dealt with in anoth er paper, with only the Ti-Cr and Ti-V systems being discussed here. EXPERIMENTAL TECHNIQUES Alloys employed for the delineation of the systems under investigation were prepared from iodide titanium sheet capsules containing the alloying materials,

Jan 1, 1962

By O. S. True, C. H. Herty

It is well known that manganese will desulfurize molten iron through the formation of manganese sulfide, which, being only slightly soluble in the metal, rises to and enters the slag where it remains as such (mixer slag) or is converted partly or wholly to calcium sulfide (basic open-hearth slag). The reaction by which manganese sulfide is formed is Mn + FeS = MnS + Fe. This reaction is generally considered to be reversible, although McCancel states that such is not the case. The experimental work was carried out to confirm the results of Roh12 as to the reversibility of the reaction. Six trials are herein considered. In each 200 gm. of electrolytic iron free from manganese and sulfur were melted in a pure zirconia crucible in a carbon resistance electric furnace. To the melted iron in runs 2, 3 and 4 metallic manganese and manganese sulfide were added to give 1, 2 and 4 per cent. manganese respectively, with 0.50 per cent, of sulfur in each. In runs 5, 6 and 7, metallic manganese and iron sulfide to give the same proportions of. manganese and sulphur as in runs 2, 3 and 4, were added. The melts were held molten in the furnace for an hour and then cast into small ingots. The results of these melts are as follows: Ingredients of Charge Analysis or InRot ManOaneBe, SulfUR, ManOaneBe. SULFUR, Run Material Charged PeR Cent. PeR Cent. Per Cent. PeR Cent. 2 MnS + Mn............... 1.0 0.452 0.636 0.367 3 MnS + Mn............... 2.0 0.50 1.57 0.310 4 MnS + Mn............... 4.0 0.50 2.81 0.230 5 FeS + Mn................ 1.0 0.50 0.647 0.397 6 FeS + Mn................ 2.0 0.50 1.45 0.374 7 FeS + Mn................ 4.0 0.50 2.73 0.195

Jan 1, 1925

By E. O. Bennett

When oil is takcn from a subsurface structure it is generally accompanied by gas. The gas thus produced represents the 1ighter hydrocarbons present in the original petroleurn accurnulation, which arc, insoluble at the reduced pressures created around a well when it is producing. In some cases the gas accompanying the oil may come from a gas-bearing stratum not in immediate contact with the oil. The amount of gas from the formation accompanying each barrel of oil is called the natural gas factor. Energy Causing Well to Flow The force causing the flow of fluid into a well when it is drilled into an oil-bearing structure is the pressure differential between the well bore and the formation. A pressure differential between the formation and the well may be set up in three different ways, as follows: (1) pressure due to gas in solution or in contact with the oil, (2) hydrostatic pressure due to water in contact with the oil (it may be either bottom or edge water); (3) pressure difference due to forcc of gravity. The greatest source of energy for producing oil from most oil fields, and the one over which the greatest control can be exerted, is the poten-tial energy in the gas under pressure in the formation. In any pool there is but a definite amount of gas available. Part of this gas may be in solution and a part in contact with oil. The amount of gas in solution in each bard of oil depends on the pressure and temperature in the formation and the characteristics of the oil. Whether the gas is in solution or in contact with the oil it is necessary to use the energy it, contains as efficiently as possible in order to obtain the greatest ultimate recovery from the pool. Bush1 states: Gas being the most efficient aid in moving the oil, it is important to prevent more of it from escaping than is necessary to remove the maximum amount of oil from the sands. The conservation of this energy is far more important to the producer of oil than his returns from sales of gas to distributing companies. The flowing life of the well is the most profitable period, and keeping the gas-oil ratio low, or keeping the

Jan 1, 1928

By E. G. Williams

Manganese-ore has been found upon the Isthmus of Panama throughout' a region of nearly three hundred square miles, over the greater part of which, however, it is known only in small bodies without commercial value. Only six mines, controlled by two companies, have actually shipped ore, although a large area has been taken up in miningelaims. The ore-bearing region extends along the coast of the Carib. bean Sea, beginning on the west near Puerto Bello and extending easterly about 35 miles toward Point San Blas. Ore has been discovered in the interior, at a maximum distance of about 10 m. from the coast. Fig. 1 is a map of a portion of the Isthmus

Jan 1, 1903

By William Loblowitz

A simplified system of flotation testing has been developed recently at the Bureau of Mineral Research of Rutgers University. The technique involves the known principle of skin flotation and can be used with minute quantities of sample and reagents in a beaker. A vessel containing the conditioned sample with added water and flotation reagents is held inclined and rotated slowly. Water-repellent particles come in contact with air and float on the surface of the liquid, while wettable particles are submerged. The float is poured off and filtered whereas the nonfloat remains in the beaker. The filtrate may be returned to repeat the process. This procedure can be made quantitative. Separations are obtained and are remarkably complete and repeatable. The effect of different reagents, optimum quantities, pH and other variables can be determined in a fraction of the time required for conventional testing. However, the method gives no information on the effect of frothers and the quality of froth to be expected in a cell, and it is not practical for particles finer than 200-mesh. Unlike other preliminary tests, separate float and nonfloat products are obtained, and their contents can be determined quantitatively by chemical analysis or grain counts. After the optimum reagent combination has been determined, the effect of fines and frothing may be verified in the conventional flotation cell. On the other hand, agglomeration-tabling can be directly duplicated from beaker tests. Procedure: Five to ten grams of sample are weighed into a 100-ml beaker. Flotation reagents and a small initial quantity of water are stirred together; additional water is then added to produce the proper water-solids ratio. The beaker is then tilted to 45" and rotated slowly. After three to five rotations, liquid and float are poured off and filtered; the filtrate may be recycled until the separation is completed. One test generally requires less than 10 min. Reagent concentration and pH remain quite constant because of the recycling of the filtrate. Two to four tests may be made simultaneously, and the effect of varied conditions may be observed by comparison. Considerable time is saved in preparation and handling since small quantities of sample suffice for a series of systematic tests. Repeatability One test was repeated four times under constant conditions. The sample used was a quartz sand containing approximately 24 pct feldspar and some clay aggregates. The +28-mesh grains had been screened out, and most of those finer than 100-mesh had been removed by hydraulic classification. The results are presented in Table I. For comparison, 500 g of the sample were separated by agglomeration-tabling using the same reagent combination and quantities as given in Table I. The weight percent float was 18.3 pct, composed almost entirely of feldspar and with only traces of quartz. Most of the remaining feldspar was recovered in a middling product with 2.2 pct by weight.

Jan 1, 1952

Discussion of the paper of J. E. Johnson, Jr., The Effect of High Carbon on the Quality of Charcoal-Iron, presented at the Cleveland meeting, October, 1912, and printed in Bulletin. No. 74, February, 1913, pp. 173 to °14, and of the paper of Albert Sauveur, Notes on Cast-Iron, presented at the New York meeting, February, 1013, and printed in Bulletin No. 75, March, 1913, pp. 503 to 524. CHAIRMAN. JOHN BIRKINBINE :-Just 20 years ago I had the pleasure, when I retired from the Presidency of the Institute, of introducing my successor, and this afternoon it is my pleasure to ask my good friend Dr. Howe to open this discussion. PROFESSOR HENRY M. HOWE, New York, N. Y. :-This paper of Mr. Sauveur's is extremely interesting. It is one of those papers that one wishes to read in the quiet of one's study, where it can be read with great profit. There are many points which he makes which I think are of very great value, in particular as to the importance of getting fine ;grained graphite by a relatively rapid cooling, combined with a high percentage of silicon. That theory would seem to be very promising; how far it has actually been carried out very likely Dr. Moldenke can. tell us.

Jan 5, 1913

By Norman B. Pilling

Practical limitations to the usefulness of silicon steels are the hardness and brittleness silicon imparts to iron, making iron-silicon alloys of more than 8 per cent. silicon content unusable except where castings can be employed. In the use of commercial silicon steel, in thin rolled sheets, as in transformer construction, when the silicon content exceeds 4.2 per cent. the sheet is too brittle for satisfactory shaping by punching or similar operations. When such a brittle steel is sheared, it frequently breaks along a haphazard path in advance of the cutting tool. In Fig. 1 is shown a slightly enlarged view of the sheared edge of a 14-mil enameled sheet of nominally 4 per cent. silicon steel. In 5 in. along the sheared edge, only 44 per cent. was actually cut; the rest was torn, with the path of fracture varying widely from the path of travel between the shears. This is probably an extreme case of such brittle-ness, but a shearing or punching test is not necessary to reveal brittle-ness of this order; narrow strips will break when bent between the fingers. In Fig. 2, the proportion of actual cut edge is greater, but secondary fractures branch off at about 30" from the line of shearing in advance of the cut. Deprived of the support of adjacent parts of the sheet, the tips of the angles are bent out of the plane of the sheet by the shears, leaving a peculiar flared effect, like the set of the teeth on a saw. An end-on

Jan 1, 1923

By Oliver C. Ralston

THE two chemical compounds, natural sodium carbonate and sodium sulphate, in their anhydrous condition are dealt in as "soda ash and "salt cake”-names from an earlier day that are not as precise as the present accepted terminology. Once a large part of the sodium carbonate recovered was in the ash of seaweed, so it was logically called soda ash, and the corresponding potassium carbonate, once mainly recovered from wood ashes, was called potash. The term "salt cake" was applied to the sodium sulphate resulting from interaction of sodium chloride with sulphuric acid or sodium bisulphate, to form hydrogen chloride gas and an anhydrous cake of sodium sulphate. It was called "salt cake" and also "glassmaker's salt cake" because much of it was used in the production of glass. The two salts occur in nature in a variety of forms, but whereas an- hydrous sodium sulphate (thenardite) is fairly common, the anhydrous normal sodium carbonate, Na2CO3, is almost never found in nature. The monohydrate (thermonatrite), Na2CO3.2H2O, is seen occasionally, but it is never a major constituent in natural "soda" deposits. The high solubility of normal sodium carbonate is one reason for this. While both compounds occur widely in brines, the solid salts found in nature are usually trona (Na2CO3.NaHC03.2H2O) and thenardite (Na2SO4). The natural brines containing workable quantities of the two sodium salts are largely found in the arid and semiarid portions of the western United States and other countries. The classical discussion of the resources of these brines are those of Clarke,5 Chatard.4 Packard,19 Gale,11 and Wells.28 From North Dakota to California and from Arizona to the Canadian provinces of Alberta and Manitoba, saline lakes, dried-up lakes, playas, and similar land-locked depressions contain accumulations of saline matter. Sodium chloride is the predominant salt but some of the lakes contain predominantly either sodium carbonate or sodium sulphate. Often sodium carbonate

Jan 1, 1949

Jan 1, 1907

By E. I. Larsen

Powder metallurgy has been described as being "as old as the pyramids and yet as new as the latest bomber." While this may be true literally, it has been only in the last Io or 1 5 years that widespread use has been made of this method of fabricating various articles One of the first items fabricated by powder metallurgical methods on a commercial scale was electrical contacts, which were fabricated from metal powders as early as 1920. The reason why these contacts have been made for so many years by powder metallurgy is because the compositions of most of these materials arc such that they could not be made by the conventional methods of melting, casting, rolling, drawing, etc. Classes of Contacts In general, electrical contacts fabricated from metal powders fall into two classes, both from the point of view of the method of fabrication and the components that make up the chemical composition. One class is composed of silver or copper and a refractory metal such as tungsten, molybdenum, or compounds thereof such as carbides. The second class contains a predominant amount of silver and a semi-refractory material such as cadmium oxide, nickel, cobalt, or graphite. Electrical contacts of the first class have been developed primarily as facing materials for heavy-duty circuit-interrupting devices. This class of material unites the high melting point, high boiling point, great resistance to electrical erosion, and the refractory characteristics of molybdenum, tungsten, or their carbides with the high thermal and electrical conductivities and low contact resistance properties of silver or copper. The second class of material is used for lighter duty or specialized applications such as heavy-duty, direct-current aircraft relays. Varieties Electrical contacts fabricated from metal powders are made in a wide variety of compositions, shapes, and sizes. In general, the sizes of electrical contacts fabricated from powders vary from contacts weighing approximately 0.001 oz. up to those weighing 3 to 4 Ib., the contacting face being as small as 0.001 sq. in. up to approximately 6 sq. in. in area. The shapes consist of: sound or rectangular buttons, some of which have radii or bevels on the contacting faces; rings, cups, rectangular bars, the contact face of which may have a radius across the width and/or at one end; and form-pressed pieces of a wide variety such as angles, both acute and obtuse, irregular shapes comprising a radius blended into a flat, which in turn may have steps. The size or shape of the contact is dictated principally by the mechanical design of the manufacturer, who in turn may have problems to be met such as: (I) size, weight, or space limitations; (2) electrical conditions such as blowout coils arc chutes, baffies, gas passages.

Jan 1, 1945

By Irwin Roman

PART I. INTRODUCTION THE literature of geophysics as applied to the discovery of mineral deposits has been very extensive during the past few years, but there seem to be few references to the use of the method of least squares for obtaining better interpretations of the observed data .2 There seems to be a general reluctance among geologists and. engineers to acquire the technique of least squares, in spite of the fact that a thorough knowledge of the theory is not necessary for the use of the method.

Jan 1, 1931