Search Documents

By R. S. Reed, D. L. Ward

This paper is the result of a study, in 1919, to determine how much surplus power could be produced through the proper utilization of the entire gas flow from the two furnace stacks at the Federal Furnace Plant, South Chicago, 111. Obviously, the problem was to measure the flow of gas through the main beyond the point where the amount necessary for stove operation mas rermoved. In all probability, blast-furnace gas is the most difficult gas to measure, because of the high moisture and dust content, and the widely fluctuating flow from the furnaces. This wide fluctuation of flow forbids the acceptance of any one group of flow road-ings as indicative of normal operating conditions. A study of the conditions showed that a recording device on gas flow was necessary. As the gas at the point of measurement had passed through met washers, and accordingly was saturated with water and contained considerable dust carried past the scrubbers in the form of sludge, no form of Pitot tube could be used, for this sludge would quickly plug the dynamic. and static holes, spoiling the gage readings. An even more serious objection to the use of Pitot tubes was the impossibility of accurately measuring the cross-sectional area of the gas main on the plane of Pitot-tube installation. Given an absolutely clean gas and a perfectly circular pipe, it would be safe to assume, through measurements of the pipe diameter, that the gas main was of a certain cross-sectional area. But the continual depositing of sludge and the fact that the main mas fabricated from riveted sheets led us to discard the idea of using Pitot tubes for. this service. The Venturi tube mas then considered, and had there been a sufficiently long straight run of gas main to accommodate a tube of the required size (72 by 28 in.) such an installation would very likely have been made. A plate with a sharp-edged orifice was eventually accepted as it possesses all the characteristics of a Venturi tube, requires less space, and

Jan 1, 1922

By Dennis A. Clark, Brent Larsson

Tunnelling today is a lot more than drilling and blasting. The developments in drilling and blasting technique have made it pos¬sible to save costs both by increasing the advance per round and optimizing the demands on the final contour. Increasing the hole depth by using longer feeds and bigger dril¬ling rigs make the drilling time shorter compared to the set up time. It is important that the deeper holes are followed up by using a suitable cut. The most common cut in Sweden today is a parallel hole cut with one or more large holes; with a diameter corresponding to the hole depth and wanted advance per round. It is often specified that smooth blasting is to be carried out with a specific drill hole spacing. It is extremely rare, however, for specifications to be issued concerning the alignment of the raw of holes closest to the contour holes. It is very easy to ruin the effect of smooth blasting altogether by firing the rest of the round carelessly with an excessively high charge distribution. The drilling and blasting of the contour holes and the line of holes closest to the contour holes is therefore an extremely important part of any underground work. Accuracy and care in connection with the drilling of contour holes is also extremely important since it is possible to reduce the amount of overbreak, the result being more rapid mucking out, smoother and more durable surfaces and also less consumption of concrete for lining purposes.

Jan 1, 1983

By E. W. Mehal, R. H. Cox

A planar Gunn oscillator was developed for use in a monolithic microwave integrated circuit. The device was designed to operate in the frequency range of 20 to 30 GHz with a continuous wave output. Selective epitaxial deposition was used to form the n+n-n+ device structure in (111)-B semi-insuluting GaAs. The active n- region was about 5 µ thick and was doped to about 2 x 1015 electrons per cu cm by the reactor background. The mobility was -5000 sq cm v-1 sec-1. The n+ epitaxial deposits were doped to 1 x 10" electrons per cu cm using S2Cl2. Planarity of the three DURING the past few years, new microwave devices in discrete form have been developed utilizing GaAs. The next logical step is to combine these devices in a successive deposits was quite good; total overgrowth was less than 1 µ. Metal ohmic contacts were applied to the n+ or n- regions using a Ag-In-Ge alloy. The n+n-n+ devices had symmetric IV characteristics and could be operated C. W. for both directions of device bias. Metal ohmic contacts made directly to the n-region always Produced asymmetric devices. C. W. operation was obtained over the 22 to 28 GHz frequency range. The best performance obtained was 1.5 mw C. LV. output at 28 GHz. microwave integrated circuit. A potential application would be a radar receiver operating in the millimeter wavelength region. The key component in such an integrated circuit is a microwave oscillator, recently described by Gunn.1, 2 Under the influence of a large electric field, high-resistivity GaAs exhibits a bulk negative resistance, and high-frequency current oscillations result. Since relatively high voltage and

Jan 1, 1969

By Herbert Clark Hoover, Lou Henry Hoover

We give the following brief notes on early works containing some reference to mineralogy, mining, or metallurgy, to indicate the literature available to Agricola and for historical notes bearing upon the subject. References to these works in the footnotes may be most easily consulted through the personal index. GREEK AUTHORS.-Only a very limited Greek literature upon subjects allied to mining or natural science survives. The whole of the material of technical interest could be , reproduced on less than twenty of these pages. Those of most importance are : Aristotle (384-322 B.c.), Theophrastus (371-288 B.c.), Diodorus Siculus (1st Century B.c.), Strabo (64 B.c.-25 A.D.), and Dioscorides (1st Century A.D.). Aristotle, apart from occasional mineralogical or metallurgical references in De Mirabilibus, is mostly of interest as the author of the Peripatetic theory of the elements and the relation of these to the origin of stones and metals. Agricola was, to a considerable measure, a follower of this school, and their views colour much of his writings. We, however, discuss elsewhere1 at what point he departed from them. Especially in De Ortu ct Causis does he quote largely from Aristotle's Meteorologica. Physica, and De Coelo on these subjects. There is a spurious work on stones attributed to Aristotle of some interest to mineralogists. It was probably the work of some Arab early in the Middle Ages.[ ]

Jan 1, 1950

By Junius D. Edwards, Cyril S. Taylor

Magnesium is the lightest metal used for structural purposes, for which reason perhaps more than usual interest is attached to measurements of its density. Although the density of solid magnesium has been det,ermined frequently, no measurements of the density of the liquid metal are available. Because of unusual experimental difficulties in measuring the density of the liquid, only a limited number of measurements of good precision were secured. The results, especially the value for the crystallization shrinkage, are of great interest in connection with the casting of the metal. A number of samples for these measurements were made available through the courtesy of the American Magnesium Corp. They were in the form of extruded bars 3/8 in- in diameter and several were of exceptional purity, as indicated by careful analyses. Table 1 gives the density values (at 20" C.) for magnesium of varying degrees of purity. The density was measured at room temperature by comparison of the weight in air, and when immersed in distilled water. The necessary buoyancy corrections were applied, so that the density could be expressed in absolute measure—grams per milliliter. The effect of the buoyancy of the immersed suspension and the surface-tension pull of the water upon the suspension were eliminated from the results by a preliminary weighing of the suspension immersed to the working depth. Great care was necessary to prevent the introduction of a significant error by the formation of gas bubbles upon the clean magnesium surfaces; these are sometimes very minute and easily escape observation. They may be detached by raising the specimen from the water and again immersing; this should be done just prior to completing the weighing. Their formation may be almost entirely prevented during a measurement by previously immersing the specimen in a solution of paraffin in petroleum ether. The thin film of paraffin remaining after the evaporation of the solvent prevents wetting of the magnesium surface by the water. In one such determination, the paraffin coating on a 22-gm. Specimen

Jan 1, 1923

By H. W. Hitzrot

*Original Pages Missing From Book

Jan 5, 1954

By R. L. Brown, A. C. Fieldner

Committee it supports pioneering research on the development of a coal-burning gas turbine and through the Mining Development Committee it promotes research on a new type of continuous mining machine that operates without using explosives. Other organizations have contributed major publications on fundamental and applied coal research in the last two decades, including the Minerals Industries Experiment Station of Pennsylvania State College, the Illinois Geological Survey and University of Illinois, the University of West Virginia, the University of Michigan, the University of Alabama, the University of North Dakota, the Massachusetts Institute of Technology, the Koppers Company, the U. S. Bureau of Mines, and, in recent years, the Institute of Gas Technology. Engineering development work, which is included in the overall estimate of $20,000,000, is conducted largely by manufacturers of equipment, and this portion of the estimate is difficult to gage. It represents a large proportion of the estimate and probably is too small rather than too large. For example, the development of mobile coal-loading machines and continuous mining machines, outstanding in recent mining research, undoubtedly involved a high cost. Coal Mining From an economic point of view, the greatest research development in the coal industry obviously has been the growing degree of mechanization in mining. The percentage of underground-mined bituminous-coal output mechanically loaded has risen from 3 pct in 1926 to 67 pct in 1949. Coal operators and equipment , manufacturers have united in designing machinery. Loading machines of large capacity and astonishing flexibility are in common use. Shaking conveyors transport coal from producing faces to transfer points from which it may be carried long distances underground and on the surface; and in many mines rubber-tired shuttle cars carry the coal from the loader to the

Jan 1, 1952

By G. G. Luther, C. E. Jackson

THE relationship between hardenability and weldability has been mentioned many times. The ease of making a hardness survey has led to its wide use as a criterion [ ] of weldability and with a given class or series of steels for which the ductility under weld heat-treatment is known the test is entirely suitable. However, in studying a new steel the hardness survey is of less value, since it is based on the assumption that there is a correlation between hardness and ductility. Several attempts have been made to derive indices for weldabilityl and hardenability from the chemical analysis. In most of these proposals the effects of the different elements were considered to be additive, but recently Grossmami2 proposed a novel method of calculating the hardenability of a steel from its chemical composition. In the [ ] method proposed, a steel is considered as having a base hardenability due to its carbon content and grain size, and this base hardenability is multiplied by a factor for each chemical element present, The final product is the hardenability. The purpose of the present study is to point out the possible relationship between hardenability and the effect of welding on hardness and ductility for a number of plain carbon and low-alloy steels. The composition of the 25 steels reported in this paper as determined by chemical analysis is given in Table I. To eliminate the effect of variations in finishing temperatures, the 1/2-in. plates were normalized after heating for one hour at 1650°F. in a controlled-atmosphere furnace.

Jan 1, 1942

By A. L. Mular

Optimization strategies of possible interest to mineral processing are reviewed and typical strategies initiated in processing plants to date are discussed. Both On-Line and Off- Line optimization procedures have been employed by industry, assisted either by operators or by digital computers. In every case, dollar benefits have accrued.

Jan 1, 1976

By W. Mostowitsch, H. O. Hofman

In a previous paper,' The Behavior of Calcium Sulphate at Elevated Temperatures with Some Fluxes, we published the results of our investigation into the behavior of calcium sulphate in air; that is, under oxidizing conditions. The results as a whole hold good for a neutral atmosphere, or one which has no chemical effect upon calcium sulphate. The present paper deals with the behavior of calcium sulphate under reducing conditions, the reducing-agents employed being carbon monoxide and carbon, and the changes the calcium sulphide formed undergoes when it is subjected to an oxidizing-roast. Technical literature deals very sparingly with the subject. The information furnished by the recent leading chemical manuals is general. Thus Dammer,2 Missan,3 and Abegg4 quote Berthier as having reduced, in 1823, calcium sulphate with carbon, and Stammer as having done the same in 1851

Jan 1, 1911

By Marius R. Campbell

Every mining engineer who has engaged in prospecting for coal in flat-lying rocks understands the importance of constructing geological sections across the territory which he has to prospect. If the area is small and the time and means at his command are unlimited, he can construct such sections with the transit and level; but if the area is great and the examination hurried, as it frequently is, he will doubtless be puzzled how to proceed. Under this pressure of time and means, his work will probably be, to a great extent, devoid of any system, being simply a hap-hazard opening of such seams as show in outcrop at some point on the territory, without any determination of geologic structure or stratigraphic succession. Prospecting carried on in this manner is never satisfactory to the intelligent mining engineer, for he must realize that the information which he is able to furnish to his employer is totally inadequate to determine the economic value of the property. To the owner of the land such a report is no more satisfactory than to the engineer. Unless the latter can show both

Jan 1, 1897

By J. Poijärvi, J. Rastas

Recently, when increasing attention has been paid to mercury for environmental reasons, the interest of several plants is directed to the removal of mercury from roaster and smelter gases. When Outokumpu Oy built its zinc plant at Kokkola in 1969, intensive development work was started to find an efficient and economic method for mercury removal from roaster gases. A process was developed, after laboratory research and pilot plant tests, to eliminate and completely recover mercury from the roaster gases. The process was commissioned in 1970. The behaviour of mercury in the roasting process and several possible methods of removing it from gases are discussed in this paper. Theoretical investigations and empirical tests show that the removal of elemental mercury from gases by sulphatization is very efficient. Further, it is stated how the technical process was built on this idea. The zinc sulphide concentrates contain small quantities of selenium, chlorine and fluorine. The role of selenium in the process is described. Similarly, the behaviour of chlorine and fluorine in the roasting, sulphatizing and scrubbing units has been discussed. Finally, the recovery of purified mercury and selenium from the precipitates is described.

Jan 1, 1973

By J. F. Wilkinson

A high degree of accuracy is often required in mine-surveying, in order that expensive mining work may not be misdirected. The making of underground connections by drifts or shafts located as the result of surveys presents a crucial test of correctness not usually involved in any other class of surveying. In view of these considerations, the present notes and description of a survey made in June, 1890, for the San Francisco shaft of the New Almaden quicksilver-mines, may be of interest to members of the Institute who are surveyors. The purpose of this survey was to locate on the surface a vertical 2-compartment shaft (3.5 by 7 ft.), to connect with another vertical shaft, of practically the same size, which had been sunk a number of years before from an adit-level about 240 ft. vertically below the surface, to a deeper, so-called 600-ft. level. It will be seen, of course, that the most important matter was to secure an exact coincidence in vertical line, so that the resulting continuous vertical shaft from the surface should have no offset or irregularity at the point of junction between its two parts. The levels were of less importance; but, as the hoisting-works were to be placed in position and the new shaft permanently timbered from the start, its correct alignment was an essential requirement. The important features of the work, therefore, were the methods used in determining with certainty : 1. That the shaft was located in the right place in a general way; 2. That the ordinary inaccuracies of linear and angular measurements were so reduced as to insure correctness of location within certain defined and allowable limits. Instruments.—Thc instruments used were: a Buff and Berger transit-theodolite, with a 6-in. horizontal plate, reading to 10 seconds; a Heller and Brightly Y-level; a Chestermán steel tape, graduated in tenths and hundredths of a foot; and New York leveling-rods, graduated to thousandths of a foot.

Jan 1, 1901

By John Birkinbine

The early history of the mining and metallurgical industries of Pennsylvania is so intimately associated with the section of the State in which we meet, that a brief resume of a few of the important historical facts, and a reference to some of the more modern enterprises, in which members of the Institute have been largely concerned, seem appropriate to this occasion. It is just two hundred years since the publication of the earliest mention of the manufacture of iron in Pennsylvania. What kind of iron this was, or where or by whom it was produced, is uncertain. The only record of it is the following verse, quoted in the admirable work of Mr. James M. Swank,* from a poem published in 1692: " A certain place here is, where some begun To try some Mettle, and have made it run, Wherein was Iron absolutely found, At once was known about some Forty Pound." One who stood one hundred and seventy years ago on the summit of this Neversink Mountain † (had the atmospheric conditions been favorable, and the timber somewhat removed) might have noticed in the daytime the smoke, or at night the reflection, from the fires of the first successful Pennsylvania iron enterprises, scarcely 15 miles to the south, viz.: Rutter's bloomary forge, built in 1716, and the Colebrookdale blast-furnace erected in 1720, respectively 3 and 8 miles distant from Pottstown. Here the pioneers of iron production in the State which has so long led, and still leads all others in this manufacture, had their trials and successes ; and it may be a satisfaction to some who bewail a present depression in trade, and the low prices now ruling, to recall the fact that in 1731 pig-iron is reported to have been sold ''in large quantities" at the Colebrook-

Jan 1, 1893

AMONG the features that make Inspiration of outstanding A interest, particularly to the engineer, is the fact that at various times it has used, as a major method of production, three more or less distinct methods of mining and three distinct methods of treating its ores. The following chronology is of interest : Major Mining Methods: 1915-194 7 Underground block-caving, exclusively 1948-1952 Underground block-caving and opencut mining 1953-1954 Underground block-caving, opencut mining, and "glory-hole caved-block transfer" mining 1955 on Opencut mining and "glory-hole caved-block transfer" mining. Major Ore Treatment Methods: 1915-1925 Flotation concentration exclusively 1926-1930 Flotation concentration and ferric sulphate leaching 1931-1955 Ferric sulphate leaching (the so-called "Dual Process" was used for eleven months in 1937 when demand for copper was phenomenal; and the "leach-float" process was used for 24 months in 1942-44 as an expedient to help meet war demands for copper). 1956 on "Dual Process" combining a sulphuric acid leach followed by fine grinding and flotation of the residue from the leaching vats.

Jan 1, 1957

By R. S. Shoemaker

Mines are closed for two reasons; exhaustion of ore or insufficient price for the mineral. On the other hand, the reopening of an old mine can be the result of any one of three events; the discovery of more ore, a sudden rise in the price of the product or the use of a new low-cost method of mining or milling the ore. Examples of the latter would be the open-pitting of an orebody previously mined underground as recently happened at Tyrone, N.M., or the adoption of acid leaching of an old pit as has been done at Miami, Ariz. The unique native copper mines of the Keweenaw Peninsula of upper Michigan have not been so fortunate. These deposits, which were first worked by prehistoric Indians, have been mined continuously from the early 1840's to 1968 when the last mines of Calumet and Hecla were closed and the Ahmeek mill. still using eight Nordberg steam stamps, was shut down. There are two types of deposits from which native copper is obtained; amygdaloid, which is a lava flow, and conglomerate, a sedimentary deposit of sand, rock fragments and pebbles cemented together. "In the amygdaloid, the copper is disseminated, or distributed much like the raisins in a cake; but in the rich Calumet conglomerate, the copper is more like a malleable rope or thread cementing the pebbles together." (C. Harry Benedict. Red Metal: The Calumet and Hecla Story, (Ann Arbor, Michigan, 1952), p. 42.) These deposits produced almost all of the copper used by the North in the Civil War and were substantial contributors to the copper needs of the United States in both World Wars. Some were mined to depths of as much as 9500 ft along the dip of the vein structure and 7500 ft vertically. Few of the mines ever really became worked out, but became uneconomical because of depth, pinching of veins or grades which dropped to about 1%.

Jan 5, 1972

By William E. Ford, Edward Salisbury Dana

1. Normal Class (6) Zircon Type 2. Hemimorphic Class (7) Iodusuccinimide Type 3. Pyramidal Class (8) Scheelite Type 4. Pyramidal- Hemimorphic Class (9) Wulfenite Type 5. Sphenoidal Class (10) Chalcopyrite Type 6. Trapezohedral Class (11) Nickel Sulphate Type 7. Tetartohedral Class (12) Mathematical Relations to the Tetragonal System THE TETRAGONAL SYSTEM includes all the forms which are referred to three axes at right angles to each other of which the two horizontal axes are equal to each other in length and interchangeable and the third, the vertical axis, is either shorter or longer. The horizontal axes are designated by the letter a; the vertical axis by c (see Fig. 166). The length of the vertical axis expresses properly the axial ratio of a : c, a being uniformly taken as equal to unity. The axes are orientated and their opposite ends designated by plus and minus signs exactly as in the case of the Isometric System. Seven classes are embraced in this system. Of these the normal class is common and important among minerals; two others have several representatives, and another a single one only. It may be noted that in four of the classes the vertical axis is an axis of tetragonal symmetry; in the remaining three it is an axis of binary symmetry only.

Jan 1, 1922

By R. W. Heckel, R. A. Tanzilli

ANALYTICAL results have previously been presented for the diffusion-controlled solution of a second phase in a finite medium for planar, cylindrical, and spherical geometries.' These results were obtained by numerical methods using digital computer techniques and are applicable not only to the stage of the problem where the unstable phase shrinks to zero size, but also the subsequent stage where the concentration gradients in the matrix phase become negligible (essentially complete homogenization). It is anticipated that the results of such an analysis may be of use to those workers who are interested in the processes

Jan 1, 1970

By J. M. Larkin

GOOD will is becoming recognized more and more as a necessary business asset, and a successful concern must have the good will not only of its customers and the public, but of its employees. Management -enlightened management-recognizes this and will go the limit to get it. Progress depends on cooperation, and in industry cooperation must be based on the acceptance by employ-ers and employees of some practical application of the principle that capital and labor are interdependent. Capital cannot exist without labor, and labor without capital is helpless. The development of each is depen-dent on the cooperation of the other. Confidence and good will are the foundation of every successful enter-prise, and these can be created only by securing a point of contact between employer and employee. We feel that one of the most effective agencies for promoting good will between employers and employees is through some well organized method of conference and have consequently adopted, to accomplish this, a plan of employee representation. The plan inaugurated by the Bethlehem Steel Co. about four years ago, which provides for the election by secret ballot of representatives by and from among the employees, has for its purpose three fundamentals; namely, to give the employees a voice in the determina-tion of the conditions under which they work, to furnish machinery for the prevention and adjustment of differ-ences between employees and management, and, so far as possible, to provide and foster continuous employment. The constitution and by-laws adopted take care of the detail in setting up machinery for the functioning of the representatives of both management and men, but the spirit with which the plan has been carried out and the results which have been accomplished are of far greater importance than the plan itself. The Bethlehem plan, which has been in operation since October, 1918, can no longer be classed as an experiment. The original by-laws provided for amend-ments and, as was anticipated, changes and improve-ments have been made from time to time by mutual agreement. The operation of the plan for over four years shows it to be fundamentally sound and that it must therefore be conceded a success.

Jan 2, 1923

By Dean F. Winchester, C. D. Johnson

The so-called Rocky Mountain region is here made to include Colorado, Idaho, Montana, northern New Mexico, Utah and Wyoming, an area of great distances and relatively sparse population. Conditions of distance, transportation and markets have had their retarding influence on devolopment and production but the increase in facilities and markets in recent years has provided additional incentive for more thorough search for new productive areas and the more complete development of the known fields. The low prices of crude during the past year have offset, to a certain extent, the desire for increased production and much of the effort has been directed therefore to outlining new areas rather than to attempts to increase production from known fields and thereby add to the already sufficient supply above ground. During the year just closed the Rocky Mountain region has seen consistent efforts to outline new areas and these efforts have been reasonably successful. In this area a very large part of the land is government property, and by cooperation between the government, the private owner and the company it has been possible to carry on development in a scientific manner, providing for the maximum recovery of valuable products at least cost and at times when prices were best. Due to the fact that in the Rocky Mountain region costs of exploration and development are relatively high because of natural circumstances, it has been the policy of operators to drill test wells only on structures where they controlled a large proportion of the land. Even community lease programs have been effected in certain areas, thus obviating the necessity of offset drilling and the attendant uneconomical and even wasteful production. Oil production in the Rocky Mountain states has shown a slight increase during the year, the average daily production for November being 78,124 bbl. as against an average in January of 76,681 bbl. The total production during the first 11 months of the year, according to the U. S. Burcau of Mines, was as follows:

Jan 1, 1929