Search Documents

By J. E. House, C. J. Lewis

In the solvent extraction process, also referred to as liquid-liquid extraction, the clarified uranium-pregnant sulfuric acid leach solution is contacted with an organic extractant dispersed in kerosene; the uranium enters the organic phase and associates itself with the organic extractants. Simultaneously an-ions or cations, as the case may be, leave the organic extractant phase and enter the aqueous phase. The two phases are then allowed to separate by virtue of their immiscibility. Based on the data available, a generalized procedure for the recovery of molybdenum from the sodium carbonate scrub liquor of acid leach uranium mills using secondary and tertiary amine extractants is presented, as is another generalized procedure for the recovery of molybdenum from the bleed stream of alkaline leach uranium mill circuits. Such economic appraisal as can be made at this stage of the development is also indicated. Molybdenum occurs in most uranium ores. Whether the uranium is solubilized by the acid leach route or by the alkaline leach process, some of the molybdenum present in the ore is solubilized along with the uranium. Molybdenum in uranium mill pregant solutions may cause processing difficulties, among which may be mentioned the poisoning of resins, the precipitation of organo-molybdenum complexes, or the build-up of molybdenum in recycle streams. While the uranium milling industry has been successful in applying measures to overcome the problems arising from the presence of molybdenum in the circuits, such measures nevertheless add to the cost of producing uranium yellow cake concentrate. Table I shows the analysis of typical uranium pregnant leach solutions. Uranium recovery by solvent extraction is presently practiced only in conjunction with acid leach circuits, and it may be noted that of about 16,000 tons of uranium ore daily processed by sulfuric acid leach, more than half of this tonnage follows the solvent extraction route. Uranium mills leaching ore with sodium carbonate-sodium bicarbonate solution (the so-called alkaline leach circuit) do not use solvent extraction. In this case the uranium pregnant solution is sufficiently pure to permit the direct precipitation of uranium concentrate with subsequent recycle of the alkaline leach solution. While solvent extraction procedures may be developed which are economically attractive for the alkaline leach uranium process, this has so far not been the case. The earlier uranium mill solvent extraction circuits used organo-phosphate extraction reagents, among which di-2-ethylhexyl phosphoric acid was popular. It should be borne in mind that uranium in its sulfuric acid leach solution exists in an equilibrium involving uranium in both anion and cation forms: uo + 2S0 = [uo2(so4)2] For this reason uranium may be extracted by either cation extractors or anion extractors and this is likewise true of molybdenum. However, the organo-phosphate extractants also load ferric iron which is usually present in the uranium acid leach solution. For this reason, it is necessary to reduce this solution substantially to the ferrous state ahead of solvent extraction using organo-phosphate reagents. The amines, being anion extractors, selectively reject iron and thus render the iron reduction step unnecessary. In the solvent extraction process, also referred to as liquid-liquid extraction, the clarified uranium-

Jan 1, 1961

By L. F. Elkins

Water coming into wells with bottom water present in the Fosterton field, when their oil recovery was only 0.1 to 1.5 per cent of oil in place below the lowest perforation, confirms lack of shale barriers to vertical flow which also are not apparent in cores and electric logy. Low contrast of vertical and horizontal permeability, high mobility ratio betweerz oil and water zone and pos.rible rate effects due to gravity Combine to prevent easy analysis of water invasion pattern and efficiency by analogy or intuition. Theoretical analysis of performance including these factors using a new direct nurnerical .solution of potential distribution in a network led to unanticapted indications that water would under-run the entire oil reservoir with low volumetric coverage if supplied through natural influx or peripheral water injecfion below the oil-water contact. An unusual pattern of water injection is to he adopted in this recently unitized pool to provide more uniform water flooding in that two-thirds of the oil reservoir not underlain by bottom wafer. INTRODUCTION The Fosterton field, Southwestern Saskatchewan, Canada, was discovered in Jan., 1952. It produces at a depth of 3,100 ft from a pinch-out of the Roseray sand at the Lower Cretaceous-Jurassic unconformity. The field, covering 2,500 acres, contains 54 wells on 40-acre spacing. Development was essentially complete in June, 1954, but significant production did not start until May, 1955, when a pipeline outlet became available. Within one year rapid in- creases in gas-oil ratio and early encroachment of water created operating problems in the down-structure eastern half of the field and raised serious questions about reservoir performance and ultimate recovery. This paper describes the unusual behavior of water encroachment—on both well and reservoir bases—and the analyses made to interpret it. The field was unitized July 1, 1958, for water flooding. A somewhat unconventional

By E. J. Ripling, M. W. Toaz

Tensile tests were conducted on pure magnesium and on four commercial alloys over a variety of temperatures and strain rates. The high positive slope of the ductility vs testing temperature curves that is found over a short range of testing temperatures for these materaturerials was shown to result from the fact that the microstructure was not stable at these testing temperatures. Pure magnesium did not display a transition temperature, although its sub-room temperature ductility was low. This poor ductility resulted from a grain boundary weakness. The aluminum-bearing commercial magnesium alloys had a higher ductility than the pure magnesium. ness.Thealuminum-bearingcommercialThese alloys did exhibit a transition temperature and grain boundaries that were stronger than the grain material. Both pure magnesium and the commercial alloys began initiating cracks at strains equal to one half of their fracture strain. MAGNESIUM base alloys' enormous potential as structural materials lies in their high strength to weight ratios. At present, the high strength magnesium base alloys such as AZ-80, which will be discussed later, have about as high a tensile strength to specific gravity ratio as the highest strength wrought aluminum alloy, 75s-T6, and, of course, a much higher strength to weight ratio than structural steel. Further, since the magnesium base alloys develop their high strength to weight ratios with moderate strengths and extremely light weights, the ratio of load carrying capacity to the weight of many structures is relatively higher for the magnesium base alloys than their strength to weight ratios would indicate. This results because judicious increases in section size, such as increasing the depth of bending members or adding reinforcing ribs, can frequently increase the weight of a structure linearly while the strength and stiffness increase as the second or third power of the added weight. Strength and rigidity must be designed into lightweight structures by those techniques which establish multiaxial stress states. Consequently, strong, lightweight structures frequently also possess a greater propensity toward brittle failures. In order to insure against these catastrophic failures, an extra premium must be placed on ductility and toughness in light alloys. Current knowledge of the ductility and toughness behaviors—notched behaviors—of magnesium base alloys is limited.* Most of the magnesium base alloys * The state of present knowledge regarding the effect of testing temperature on mechanical properties has recently been summar-ized by Pritchard.' crystallize in the hexagonal system, so that they are expected to exhibit a tough and ductile to brittle transition temperature. Actually, a transition temperature behavior has been reported for commercially pure magnesium in the literature, but the characteristics of this transition temperatureh uggest that it may not be a transition in the usual meaning, but simply the onset of some thermal softening, a performance much like that which face-centered-cubic lead might exhibit slightly below room temperature. If transition temperatures do exist, such important questions as the manner in which they are affected by internal variables such as chemical composition and grain size, or the effect of external variables such as rate of straining or notch severity have never been investigated. The investigation reported upon herein was undertaken in order to define some of the mechanical behaviors of the magnesium base alloys better, to gain a better understanding of the influence of some of the above listed variables, and particularly to understand their effect on ductility and toughness better. Material and Procedure Material-—Pure magnesium and four commercial alloys were used in this investigation. The alloys were selected so that chemically they made up a series with approximately the same minor alloying

Jan 1, 1957

By W. J. Verner, J. R. Lucas

Billions of tons of bulk solid materials are processed through our industrial plants each year, and the tonnage is steadily rising. It has been estimated that for every dollar spent in industry as a whole, approxinlately 30 cents is consumed in the handling of bulk solid materials. It is in this category that tremendous savings are possible through the use of improved techniques. Since World War 11, the mining, steel, chemical, and grain industries, among others have made use of increased materials-handling automation in order to gain some of these savings. However, in a chain of automatic operations, every link must be completely reliable, for if there is a single failure, the whole system immediately becomes ineffective. Only too often the weak link in the chain proves to be the flow of bulk solids from bins. To contribute to the fundamental knowledge in this area, a research study has been continuing at The Ohio State University. The principal objective of the investigation has been to study the internal stresses existing in confined bulk solids. LITERATURE SURVEY Literature studies have revealed that many outstanding people have made contributions to the field of bulk solids. For instance, C. F. Jenkin,1 suggested: a. The pressure on a bin wall is not directly proportional to the depth beneath the surface of material in the bin. b. The vertical pressure distribution on the base of a bin is not actually uniform but is a variable. c. Arches form in bins as a result of very small deformations of the material in the bin. This deformation causes a series of gaps to appear, and consequently causes the disappearance of diagonal forces that cannot act across these gaps. The removal of the diagonal forces causes horizontal forces to be introduced which seem to be the chief cause of arching. 11. A. Janssen,4 in 1895 in connection with his experiments on bins, derived a differential equation to describe both the lateral and vertical pressure in bins with vertical sides. This represents a significant contribution to bulk solid theory, and thus its solution is reproduced as follows: L = KV = RW/U' [l-e -U'KY/R] I where L is the lateral pressure of the bulk solid in psf., V is the vertical pressure of the bulk solid in psf., K is the ratio of the lateral pressure to the vertical pressure at any point, R is the hydraulic radius of the bin in feet, W is the density of the bulk solid in lbs. per cubic feet, U' is the coefficient of friction between the stored material and the bin wall, and Y is the head of material above the point in question in feet. In 1903, Jamieson,6 in an elaborate series of experiments on full sized bins measured vertical and lateral pressures by hydraulic diaphragms. He determined many values for mediums of corn, wheat, peas, and flaxseed. In 1951, Caughey, Tooles, and scheer3 measured both lateral and vertical pressure in deep bins by using strain guages on steel bands. Values were calculated for cement, gravel, sand, soy beans, shelled corn

Jan 1, 1961

By W. H. Bassett, C. H. Davis

In the commercial annealing of cartridge brass there are four points regarding which definite data are essential. They have to do with the correct interpretation of grain count in its relation to annealing temperature and, incidentally, to Brinell hardness. These points are: 1. The comparison of the grain sizes of two cartridge-brass mixtures: 69 copper, 31 zinc, 0.376-in. (9.5-mm.) gage; and 68 copper, 32 zinc, 0.130-in. (3.3-mm.) gage 2. The comparison of the grain sizes of annealed metal that had previously been reduced by rolling varying amounts; for instance, 20.0, 36.6, 50.9, and 59.1 per cent. 3. The determination of standards for grain sizes on annealed brass of the composition 68 per cent. copper, 32 per cent. zinc and 69 copper, 31 zinc. 4. The comparison of grain size with Brinell hardness on identical samples of annealed metal. In their comprehensive and thorough investigation of the recrystal-lization of cold-worked alpha brass on annealing,l Mathewson and Phillips have discussed the relations between temperature of anneal, degree of deformation, and structural alteration in alpha brass. They have also shown certain comparisons between the ordinary physical properties and the grain size of annealed brass. The purpose of the present investigation is mainly concerned with the grain size of cartridge brass, its relation to Brinell hardness, and the publication of sufficient data to enable those engaged in the inspection of such material to have a correct foundation upon which to work. The first alloy was taken from regular mill stock that had been rolled from 0.580 in. to 0.376 in. (14.7 mm. to 9.5 mm.) gage, a reduction of 35.1 per cent. This bar (No. 1) had the following composition: Copper, 69.20 per cent.; zinc, 30.76 per cent.; lead, 0.02 per cent.; iron, 0.02 per cent. The second alloy was also taken from mill stock of 0.325 in. (8.25 mm.) gage and was rolled as shown in Table 1, in order to get four bars reduced two, four, six, and eight B. & 5. numbers respectively. This second alloy

Jan 1, 1919

By R. Costantini

The author discusses the promising future of the use of pipelines for transportation of ore slurries over long distances, citing existing installations. Various criteria and factors affecting the use and size of pipelines are considered. Among the factors influencing the use of pipelines are particle size, specific gravity, abrasiveness, minimum velocities, and pumping considerations. Long-distance transportation of solids by hydraulic pipelines holds the promise of great economic benefits. Today within the confines of most mineral processing plants, the moving of solids about in slurry form by pipeline is commonplace, since the method offers great advantages when conditions are suitable. Yet, this method is surprisingly slow in being adopted on a broad scale for transportation of solids over long distances (arbitrarily the term will be applied to one over five miles long). This is especially surprising in view of the successful realization in this country within the last five years of two daring ventures in long-distance solids pipelines. A 72-mile long, 6-in. diam pipeline of the American Gilsonite Co. has been satisfactorily transporting 700 tpd of gilsonite from the mine at Bonanza, Utah, to the processing plant at Grand Junction, Colo., since April 1957. The 108-mile long 10-in. diam pipeline of the Pittsburgh Consolidation Coal Co. has been transporting about 4000 tpd of finely crushed coal from the mine at Cadiz, Ohio, to the Eastlake power plant of the Cleveland Electric Illuminating Co. on Lake Erie since January 1958. However, besides two projects in the operations of The Anaconda Co. there have been hardly any other significant solids pipeline developments in the minerals industry during the last three years. The two projects are the 14-mile long, 6-in. diam copper concentrate gravity pipeline at Anaconda's El Salvador project in Chile which has been transporting about 800 tpd since January 1959. The second is a 16-in. diam tailings pipeline at the Anaconda Reduction Works, Anaconda, Mont., designed to transport about 20,000 tpd of deslimed flotation tailings for dam building. This pipeline, which is currently undergoing tryout tests and which will be about seven miles in length, will have a maximum of three 20-in. rubber-lined centrifugal pumps in series at the starting point, each developing a maximum of 100 ft of head, to supplement gravity. It is the writer's opinion that the major reason for the hesitation in considering pipeline operations is confusion due to an inadequate understanding of the basic physical principles affecting the slurry flow process by many engineers in the industry. This in turn begets an attitude of fear and trepidation instead of confidence on the part of many management executives, which leads to a minimizing of the advantages and exaggeration of difficulties when considering the possibility of a long-distance solids pipeline. The promotion of better understanding and consequently the promotion of greater confidence in the potentials of long-distance solids pipelines when conditions are suitable is thus the main purpose of this article. To this end, after considering several examples of the possibilities for solids pipelines in the minerals field, the relative significance of the major factors affecting pulp flow, and some major aspects of slurry pumping will be discussed on a general qualitative level. Then a brief outline of the semi-empirical quantitative methods developed to date for estimating slurry flow behavior will be presented. SOME POSSIBILITIES To give an idea of the magnitude of the possible economic benefits, it should be interesting to mention briefly some of the projects currently under consideration and to suggest some likely future possibilities. At Anaconda's El Salvador Project in Chile (Fig. 1) it is eventually planned to extend the existing 14-mile pipeline by another 60 miles to bring the copper concentrates down to the coast of the Pacific Ocean. Preliminary tests indicate that the projected 6-in. pipeline will be able to transport approximately 2000 tpd of concentrates at a pulp density of 40 to

Jan 1, 1961

By W. W. Krech, T. E. Perkins

As fractures are propagated through rocks, energy is absorbed near the extending crack tip. Apparent surface energies for several rocks have been measured by cleavage under dynamic con-ditions. At nominal crack velocities from 0.5 to 500 in (min, measurements showed that fractures propagated in discrete jumps. Calculated surface energies and moduli were relatively insensitive to nominal rate of cleavage. in another set of experiments, rocks were cleaved under high confining stresses. The rocks were submerged in low leak-off fluids which formed a filter cake on the freshly cleaved surfaces (similar to the hydraulic lracturing process). Apparent surface energies were increased substantially as the surrounding fluid pressure was increased. Moduli in bending increased significantly upon application of the first 1,000 psi but were insensitive to stress level at greater pressures. INTRODUCTION For almost 20 years, hydraulic fracturing processes have been utilized effectively to stimulate oil and gas wells. During this period, some process improvements have resulted from studies of fracture orientation, mechanics of fracturing, areas generated, conductivities of cracks, etc. Yet many questions remain concerning the conditions and pressures needed during fracture propagation. In this paper we will report additional studies of the mechanics of fracture extension. It was shown previously3 that large rock samples could be cleaved under controlled conditions so as to measure the apparent surface energy (that amount of energy absorbed per unit area of new surface created). In this paper we consider the effects of two additional factors on surface energies, viz.: (1) effect of cleavage rate and (2) effect of confining stress level. THEORY Cleavage experiments were conducted on rock samples similar to that illustrated in Fig. 1. Blocks of rock several inches wide, 2- to 3-in. thick, and up to 3 ft in length were grooved longitudinally with shallow guide slots. A crack was initiated and allowed to extend along the web as the top of the rock specimen was pulled (or pushed) apart. Auxiliary equipment permits the measurement of (1) force applied at the top, (2) separation at the top and (3) crack length. (Further experimental details will be given in the next section.) The rock beams created by the crack are considered ton be cantilever beams. The deflection (or separation of the rock beams) at any point is calculated 4,5 by the beam Eq. 1.

Jan 1, 1967

By H. K. VAN POOLLEEN, W. Hurst, H. C. Bixel

In an earlier publication* I showed the development of the instantaneous point source solution for a well producing at a constant rate at the center of a system of two radial, adjoining sands of different permeabilities. I also showed how a wellbore radius could be incorporated if this were the development required. For the purpose of that paper and the point I wished to make, this solution served. It yielded a simplifying solution of sands in series identified by Eqs. VI-26 and VI-27. (These equations are reproduced in part by Bixel and van Poollen as their Eq. 3, Page 302.) I am well aware that the simplified solutions are approximations. The facts that these Ei-functions satisfy the diffusivity equation and meet the boundary conditions both at the well and at the interface between sands, and that the earliest time considerations yield zero pressure drop, are evidence that the solutions are good approximations. This was the purpose for these formulas, which I interpret that where the permeabilities are of finite order of magnitudes in the respective media, the relations give satisfactory answers. However, from the authors' point of view there are reservations, which leads me to consider their entire generalization as illustrated in their Figs. 1 through 14. What I understand from their storage capacity, relationship Fs, which is the ratio of the product of porosity and compressibility of Sand II to Sand I, that is employed here by the authors as a correlative means of identifying one figure from another, there is nothing in the exact mathematics that supports such a term as a means of correlation. This is taken out of context, unsustained that this applies. Here the mathematics are known, where the true correlation is the diffusivity term of one sand to another. This entails permeability that refers back again to the term M in their paper for the transmis-sibility of fluid from one sand to the other that should have also been a part of this storage capacity. In Figs. 8 through 14, which purported to show the simplified equation following this correlation, there are apparent discontinuities for M equal to or less than 0.1000 that differ from the trends for greater values of M. In this connection there is no reference radius given for this cumulative pressure drop in the paper that would permit me to make these calculations. However, what is clear for M equal to 0.1000 or less we are treated to almost a closed barrier at the interface; a condition entered by the writers without qualification. This across-the-board treatment of these simplified formulas, whatever the motive of the authors, enters into a range of permeabilities that even I as the contributor would have reservations that such could apply. Under comparable conditions I would be looking at a closed reservoir or some facsimile for such. The extent to which the approximation or the exact equations pertain is not evident in the generality offered by Bixel and van Poollen in their paper. Only when they or other writers show the comparison of the pressure distributions within the formations can one be able to judge the rational limits to subscribe to the simplified formulas.

Jan 1, 1969

By R. W. Raymond

On the Manchuria. SOMEWHAT fatigued with excess of enjoyment and strenuous continuity of movement on the trip to and through California, the members and guests of the Institute party embarked Tuesday, Oct. 17, on the Pacific Mail S. S. Manchuria for a further journey to and through Japan. The good ship displayed the flag of the Institute (blue cross-hammers on a white ground), together with the Stars and Stripes and the ensign of the company. Uninterrupted fair weather and smooth water attended the passage to Honolulu. The Manchuria proved herself most commodious, comfortable and clean ("A sweeter steamship never sailed," quoth President Hunt) ; Captain Dixon and his officers were most agreeable, as well as most efficient; the passenger list comprised many congenial people besides ourselves-among them a score of missionary folk, and also Mr. M. H. de Young, Vice-President of the Panama

Jan 1, 1912

By A. M. Gaudin, J. H. Brown

In a survey of the effects of heat treatment on the comminution of various rocks, it was found that unusual size distributions often characterize the broken products, and that this is related to a great increase in intergranular fracture1. It is the purpose of the present paper to contribute to an understanding of this effect. In a thesis by one of use, critical consideration was given to many mechanisms which could conceivably be responsible for the increased intergran-ular fracture. It was shown that neither gross chemical changes nor intergranular corrosion are required. Among non-chemical mechanisms the most likely appeared to be (1) Uneven expansion due to thermal gradients, giving spalling (2) In a manner similar to that prevailing in metals, the appearance at high temperature of intergranular weakness. (3) Unequal thermal expansion of adjacent grains. Experiments were designed and conducted to permit a choice among the many alternative mechanisms and in particular among the three listed here. EXPERIMENTAL MATERIALS Tests were made on the materials listed in Table 1. Of each material, only lumps similar in composition and grain size were used. The three marbles listed in Table 1 were analyzed to assure that their chemical compositions did not differ greatly (Table 2). On the basis of the chemical analyses, of differential thermal analyses, and of X-ray powder diffraction patterns, it appeared that the marbles were very similar except for their grain sizes.

Jan 1, 1961

By D. R. Cook

This paper is a case history of an exploration venture for base metals, begun by the Rocky Mountain District of Bear Creek Mining Company in 1952 and completed in 1954. The project was based on the idea of W. S. Burbank, U. S. Geological Survey, that commercial deposits of base metals might occur in Paleozoic sediments beneath hydrothermally altered volcanic rocks in the Southern Bonanza mining district, Colorado. Here, an area of andesitic rocks, four square miles in extent, has been argillized, pyritized, chloritized and silicified. Geological, geophysical and geochemical studies were followed by the diamond drilling of three holes totalling 6,220 feet. Further alteration ang geochemical studies were made on the cores from these holes. A brief review of the alteration and geologic mapping, colored aerial photograph interpretation, geochemical soil and rock sampling, magnetic, gravity and radio-metric surveys are presented together with some conclusions regarding this work. This paper is a case history of an exploration venture for base metals, begun by the Rocky Mountain District of Bear Creek Mining Company in 1952 and completed in 1954. Important contributions were made to the project by personnel of the Rocky Mountain District and the Geophysics Division. Individual acknowledgements to these people are made at the end of the paper. BASIS FOR THE PROJECT The project was based on the idea of W. S. Burbank (1947, p. 444) that commercial deposits of base metals might occur in Paleozoic sediments beneath hydrothermally altered volcanic rocks in the Southern Bonanza mining district, Colorado. Paleozoic sedimentary rocks, including the favorable Leadville limestone, are exposed three miles south of the altered area, and reason exists to believe that they might underlie it within a reasonable depth. Alteration of pre-mineral volcanic rocks has been used successfully as a guide to concealed orebodies in the Main Tintic and East Tin tic mining districts, Utah (Bill-ingsley, 1933, p. 120-122; Lovering et al, 1949; Howd, 1957, p. 124-134; Cook, 1957, p. 73) and could be a useful guide here. GENERAL GEOLOGY AND STRUCTURE The Northern and Southern Bonanza mining districts are northwest of the San Luis Valley in southern Colorado, just within the northeastern edge of the San Juan volcanic province. The districts are1ocated on the southern extension of the Sawatch uplift, a prorninent northwest-trending structural high. The highly productive mining camp. of Leadville, Gilman and Aspen are on the northeastern and northwestern flanks of this uplift where Paleozoic limestones have

Jan 1, 1961

By Gerald Greene

Tan various lead producers have given the subject of lead drosses much attention in recent years but the problem of their economical treatment is yet to be solved. Formerly the copper in the furnace feed was removed from the furnace in the form of matte. The speiss at that time consisted principally of the iron arsenide. The practice today is to roast off most of the sulfur and the copper in the feed forms a dross in the furnace, which is removed from the furnace with the lead. This material is poured into the drossing kettles and allowed to cool down to but slightly above the freezing point of lead. The copper dross, containing almost all of the arsenic and part of the antimony, is skimmed off and treated in a small reverberatory furnace at most plants. This is essentially a liquation process. The skimmed dross contains from 70 to 80 per cent lead, and much of this lead is liquated out. The products from this treatment are: (1) impure lead, (2) speiss and (3) matte. The speiss from the reverberatory furnace was studied in this research. The literature on the subject is of very little assistance, as almost no work has been done on the problem of establishing the exact identity of the various phases present. One author(1) states that speiss consists of a series of isomorphous compounds of the general formula FexAsy in which the Fe may be replaced by Ni, Co, Cu, Pb, Ag, Au, Pt, Zn, Cd and the As replaced by Sb, S and Bi. Hofman(2) states that the iron arsenide present is Fe5As.

Jan 1, 1935

By H. D. Outmans

A method has been developed for determining the relative water wet-tability (fraction of the surface wet by water) of porous media. This method involves the adsorption of methylene blue dye from an aqueous solution onto the solid surfaces of rock contacted by the injected dye solution. Experiments on Berea snndstone cores have shown that water-wet cores adsorb a large amount of dye from solution. In oil-wet cores, however, the injected aqueous dye solution is prevented from contacting the adsorptive surfuces by a film of oil and virtually no dye is adsorbed. This method was tested by experiments on mixtures of water-wet and oil-wet sand. Using the dye adsorption method, it was possible to determine quantitatively the fraction of water-wet and oil-wet sarzd in such mixtures. The dye adsorption test is readily applied to determinitrg the relative water wettability of fresh oilfield cores. The cores are not extracted before testing. Observed values of the wettability of field cores tested to date have varied from 100 to 6 per cent water wet. INTR OD UCTIO N Recent articles1 ' have emphasized the important role that wettability plays in almost all phases of reservoir rock behavior. It has been shown that wettability has a profound effect on the interstitial water saturation, residual oil saturation, capillary pressure, relative permeability, waterflood behavior, and resistivity index of oilfield cores. A quantitative investiga- tion of the effect of wettability on these core properties is severely handicapped by the lack of a simple technique for measuring the wettability of a porous medium. If such a technique were available, it would provide investigators with a means of gaining insight into the distribution of phases within a core. A number of qualitative methods of estimating wettability are known. These include contact angle measurements, flotation tests and studies of displacement pressure: imbibition7 and relative permeability data.' Using these tests, it is usually possible to classify a core as water-wet, oil-wet, or some intermediate degree of wettability. One recently proposed method involving measurement of nuclear magnetic relaxatione offers promise of determining quantitatively the fractional wettability of cores. The equipment is rather elaborate and necessary treatment of the cores before testing probably alters the natural wettability. This latter point also applies to most of the cited qualitative methods. This paper presents a new technique for determining water wettability of cores; it is based on measurements of the dye adsorption capacity of the core. This method has the advantage of requiring relatively simple equipment and involves minimum handling of the core before testing. It is important to distinguish between the various concepts of wettability referred to in the literature. The term "wetting" is defined by Bartell as that phenomenon which occurs when a solid and liquid phase come in contact in any manner so as to form a solid-liquid interface. A preferentially water-wet solid is defined by Jennings in terms of the advancing contact angle in the solid water-oil systems. Brown and Fatt regard fractional wettability as the fraction of the total surface area that is preferentially oil-wet or water-wet. However, none of these definitions adequately describes the type wettability measured by the dye test. This calls for the introduction of a new term, "relative water wettability", which we define as the fraction of the total surface area of a core contacted by injected water. DESCRIPTION OF METHOD The ability of a porous medium (especially the clays) to adsorb large quantities of surfactants, dyes, etc., is well known. It is reasonable to assume that a substance can be adsorbed from solution onto a solid surface only if the solution contacts the surface. In this connection Shapiro" has shown by experiments on silica gel that completely dry gel will adsorb methyl red dye from a benzene solution. On the other hand, if a film of water more than several molecules thick is present on the silica gel, the adsorption capacity of the gel for the dye is drastically reduced. Thus, a study of the dye adsorption capacity of cores should give some clue as to the fluid distribution on the surface of the core. TEST OF METHOD As a qualitative check on this theory, dye adsorption tests were run on similar Berea sandstone cores (Table 1, Cores 1-5). Cores saturated initially with water and flooded with 0.01 per cent aqueous methylene blue adsorbed 0.58 mg dye/gm of core. Similar cores saturated initially with water, driven to irreducible water with oil, and then flooded with the same dye solution also adsorbed 0.58 mg dye/gm of core. Another core, treated with a 5 per cent Dri-Film solution, dried and saturated with oil (Soltrol) adsorbed no dye when the dye solution was injected. These tests confirm

By Thomas C. Wilder

Jan 1, 1965

By H. J. de Haan, L. Schenk

Scope for Thermal Recovery in Shell's Heavy Oil Fields in Venezuela The main heavy oil reservoirs on the East coast of Lake Maracaibo (Fig. I), known as "Bolivar Coast", initially contained some 20 billion bbl of oil in place with gravities in the range of 10 to 15° API. The current total production rate is about 400,000 B/D. Since the recovery to date is on an average only 12.5 percent of the initial oil in place, these fields offer a vast potential for secondary recovery methods. The reservoirs are characterized by moderate depth (generally 1,000 to 3,000 ft; maximum 5,000 ft), good formation properties such as net oil sand thickness (50 to 300 ft), high porosity (30 to 40 percent) permeability (1 to 3 darcies) and oil saturation (initially about 80 percent) and high oil viscosity (100 to 10,000 cp in situ), all of which are favorable for the application of thermal recovery processes. Since 1957, steam drive, steam "soak" and underground combustion have been tested or are being tested in this area.1-3 This paper deals with a major steam drive test in the Tia Juana field. The test was commenced in Sept., 1961, on the basis of encouraging results of laboratory experiments and pilot field tests, which will be discussed briefly. Early Laboratory Investigation of the Steam Drive Process In 1956 a series of model experiments was carried out in the Koninklijke/Shell Laboratorium, Amster- dam, to investigate the displacement of heavy oil by steam.' The prototype studied was a horizontal, un-consolidated heavy oil reservoir, subjected to a linear steam drive. The model, representing a slab from this reservoir along the main flow direction, consisted of a steel tube filled with oil-saturated sand, provided with layers of rock at the top and bottom to simulate conductive heat losses to cap and base rock. Lateral heat losses, perpendicular to the main flow direction, were minimized by insulating the sides of the model. Heat flow and viscosity and gravity forces were scaled by taking the steam injection rate and sand permeability inversely proportional to the geometric reduction factor of the model, and using materials (oil, steam, cap rock, etc.) identical with those of the prototype. The main feature of the process was a frontal displacement mechanism that was observed within wide ranges of injection pressure and rate, oil viscosity, initial oil saturation and sand permeability. The high stability of this front can be attributed to the high volumetric steam flow rates, combined with the reduction in oil viscosity. High recoveries were obtained due to the low residual oil saturation of about 15 percent in the zone swept by steam. The latter value pertains to the specific test conditions (heavy oil, uncon-solidated sand) and may be lower for light oil, due to the effects of steam distillation. The applicability of this experimental approach is limited, as it does not take into account the fact that

Jan 1, 1970

By B. P. Nutter, M. Lebourg, J. A. McAlister

The Multi-Flow Evaluator (MFE) is a new system of tools providing an original approach in drill-stem testing. It improves control during the testing operation and gives a more accurate evaluation of the fluid recovered while providing additional pressure information for reservoir analysis. The tools are operated entirely by up and down motion of the drill stem. This up and down operation provides a positive means of control and offers easily observed surface indications of tool operating position. An unlimited number of shut-in and flow periods may be taken with this tool while in the hole. The key to the success of the MFE system of tools is the safety seal packer. Until this development, operation of the tools by up and down motion only had proven unreliable. The success ratio of the MFE now exceeds the ratio achieved by conventional tools. The equipment includes a 2,750-cc chamber in which a representative sample of the flowing formation fluid is trapped at the end of the last flow period and brought to the surface under pressure. The sample can be evaluated at the wellsite or transferred under pressure for laboratory analysis. The sampling feature of the tool allows a sample to be obtained from a reservoir which has suffered minimum influence from production. A representative sample can be obtained for laboratory or empirical analysis by employing a testing technique to minimize drawdown during flow periods. Interpretation methods to take advantage of this additional information are presented and supported by actual field examples. INTRODUCTlON The Multi-Flow Evaluator (MFE) represents the most recent technical advance in formation testing. Drill-stem testing techniques prior to the MFE have been limited in three areas—(1) operaiion, (2) recovery analysis, and (3) reservoir analysis. The tools in the MFE system allow maximum control during testing and provide test information superior to that obtainable with conventional tools. The system of tools and the operation procedures are described to illustrate the mechanical advantages over present tools. Methods of pressure build-up and fluid

Jan 1, 1966

By F. S. Young

Previous laboratory and field experimentation has demonstrated the effect of several variables on drilling rate.1-5 These results have been incorporated into optimization theories6-" for the purpose of reducing drilling cost. Minimum-cost drilling theories rely on a combination of historical data and empirical prediction techniques for selecting optimum bit weight and rotary speed. Past solutions have required extensive use of computing equipment because of both the complexity of the mathematical formulations and the large number of parameters involved. Field attempts to apply these computed results have frequently failed because of the uncertainty of input data requirements. Humble has developed an on-site computer system to control bit weight and rotary speed and thereby implement the concepts of minimum-cost drilling. This system can (1) perform short interval drilling rate tests for formation evaluation, (2) use the results of these tests as input information to solve minimum-cost drilling formulas, and (3) control bit weight and rotary speed in accordance with these computed solutions. The purpose of this paper is to describe the computer control system and present results of initial field testing. Theoretical Considerations Minimum-cost drilling (MCD) requires a quantitative evaluation of the variables involved. Several forms of a basic mathematical model have been sug-gested.'?,' "he relationships reported here form the basis for the solution programmed in this work. Four equations are used, expressing drilling rate, bit bearing wear, bit tooth wear, and cost. A solution for minimum-cost drilling assuming constant bit weight and rotary speed over the entire bit life has been programmed for use in computing MCD schedules. This solution is subject to certain limiting assumptions such as those discussed by Graham et a1.I2: 1. Drilling cost is the summation of bit cost, rotating cost, connection cost and hoisting cost. 2. Diamond bits are excluded. 3. Bit life is limited by either bearing failure or tooth wear, or by a combination of operational factors that make it cheaper to pull an incompletely consumed bit. 4. Circulating hydraulics are adequate and do not limit drilling rate. 5. Bit weight considerations exclude hole deviation. 6. Drilling rate is a function of only bit weight, rotary speed, and degree of tooth dullness; that is, the effects of pressure, lithology, fluid properties hydraulics and drill string dynamics are ignored. In equation form, the four MCD expressions are as follows:

Jan 1, 1970

By Enrique Hauser

Discussion of the paper of ENRIQUE HAUSER, presented at the New York meeting, February, 1916, and printed in Bulletin No. 110, February, 1916, pp. 521 to 534. GEORGE A. BURRELL, Pittsburgh, Pa. Mr. Hauser determined the influence of inert gases on the properties of fire-damp mixtures, and one might take some issue with his work on the effect of hydrogen, on those mixtures. It is valuable information to have, but as far as the practical application of it goes, it is not of much significance, because one does not find it in mines, at least not in any appreciable amount. The same Fig. 1.-APPARATUS FUR DETECTING COMBUSTIBLE GASES IN AIR. thing can be said of ethylene. Ethylene is formed in considerable quantities as a product of heat reaction, but normally, in the coal mines, as a result of a great many analyses we have made at the Bureau of Mines, we cannot say that ethylene is a combustible gas found in the fire-damp in coal mines.

Jan 5, 1916

Who's Who in Mineral Engineering - The 1979 Directory of the Society of Mining Engineers of AIME

Jan 7, 1979