Search Documents

By H. M. Warrren

IN the past, steam engines were used in practically all cases for driving the machinery, in and about an anthracite breaker, and hence little or no accurate data were available as to the power requirements for starting and operating the individual machines, which make up the complete equipment. It was impossible to segregate the power necessary to drive each individual machine, first, because the equipment was driven in groups, and second, because it was impracticable to obtain graphic, integrated, or instantaneous records of the horsepower used. As a result of these conditions, it was found, when individual electric motors were applied to the various machines, that more accurate and complete data were needed in order to provide motors of the proper power and design for the particular services to be rendered. In order to obtain the desired information, the writers made and collected a number of tests, from time to time, on the individual motor drives in- electrically operated breakers, and as these tests have been of great value, it occurred to them that a paper giving the results might be of service to other engineers interested in similar installations. Table I shows the .results of these tests. All the motors tested were of the three-phase, 60-cycle, 440-volt, induction, squirrel-cage type, except a few, which, on account of size and starting conditions, were of the wound-rotor type. The instruments used in making these tests were: An integrating watt-hour meter, a graphic ammeter, and a graphic voltmeter. These instruments were connected in each motor circuit, and a record of a day's run of 9 hours was obtained from each machine. From these tests, the running light load, the average all-clay load, and the instantaneous peak readings in amperes, volts, and kilowatt input, were obtained. By means of the characteristic curves obtained from these motors at the factory, the power factor, the efficiency, and the horsepower output were calculated for each particular test. Starting tests were made by the brake-arm method, in which the torque in pounds was measured directly on a spring balance.

Jan 2, 1916

By R. A. Corley, W. R. Wilcox, J. R. Teviotdale

Chemical vapor deposition of hafnium carbide yielded whiskers, needles, dendrites, faceted crystals, and adherent coatings. The gas stream compositiom and the mass transfer conditions determined the habit of the deposit. The deposits were obtained at temperatures ranging from 1100" to 1800°C. HAFNIUM carbide has the highest melting point of any binary compound; therefore, its various potential applications are a subject of vital interest to the aerospace industry. The experiments described herein were performed to investigate the chemical vapor deposition of hafnium carbide with particular interest being placed upon the possible production of high-strength single-crystal whiskers for composite materials. In 1931 Moers 1 used a gaseous mixture of HfC14, Hz, and toluene to vapor deposit crystalline hafnium carbide on a tungsten filament heated to 2400°to 2800°C. More recently Lepie 2 deposited hafnium carbide on graphite using HfC14 and methane in a helium gas carrier. The pyrolytic depositions described here were accomplished in graphite tubes by using various gas mixtures and dopants. The resulting crystal habits included whiskers, needles, needle dendrites, bulbous dendrites, faceted crystals, and smooth, adherent poly-crystalline layers. EXPERIMENTAL The depositions were carried out in an induction-heated graphite tube, 1.2 cm ID, which was contained in a vertical 9-cm-ID quartz tube. (A more detailed account of the experimental procedures and results is given in Ref. 3.) Refractory oxide fiber and tubes and graphite felt were utilized jointly and singly for therma1 insulation. A typical temperature distribution is shown in Fig. 1. The reactant gases were introduced at the top and removed at the bottom of the tube. Table I summarizes the experimental conditions and results. Many deposition habits were obtained. X-ray analyses showed that they possessed the hafnium carbide structure. Almost invariably these formed well above the point of maximum temperature in the graphite tube. The habit depended strongly on the gas composition. In a series of runs (e.g., run A) using HfC14 and toluene in H 2, hafnium carbide coatings, Fig. 2, were reproducibly obtained at the position where the tube wall was 1400°C, and bulbous dendrites, Fig. 3, were

Jan 1, 1969

By William Sharp

DISCOVERY of new ore in the Eureka district, Nevada, as a result of bold and persistent exploration based on a geologic interpretation of structure has recently aroused wide comment in mining circles. It may therefore be of interest to the profession to have a summary of the historical background and an account of the recent program of development. The mines of Eureka, discovered in the late 1860's, were the first important silverlead mines in the United States. They have a production record of more than fifty-one million dollars.1 After the ore bodies were apparently bottomed in the 1880's, repeated attempts to find new ore were unsuccessful until 1940, when a diamond-drill hole cut a 40-ft width of sulphide ore 1409 ft below the 841-ft level of the Locan shaft. The next hole cut 30 ft, of ore and three additional holes drilled in 1943 and 1944 showed the ore body to be continuous, Shaft sinking to reach and open up the ore body has been in progress since 1945. GEOLOGY Stratigraphy The ore in the Eureka district occurs in a series of Cambrian sediments which is exposed through a thickness of over 6000 ft. The stratigraphic column is as follows:2 [THICKNESS, FI ORDOVICIAN Pogonip limestone (upper part). Thin bedded limestone with some chert. UPPER CAMBRIAN: Pogonip limestone (lower part). Thin-bedded limestone (with shaly limestone and chert).... 425+ Dunderberg shale. Shale (clay and calcareous shale) and thin bedded limestone340+ Hamburg dolomite. Dolomite and limestonegoo+ MIDDLE CAMBRIAN: Secret Canyon shale. Shale and thin-bedded limestone1,035 Geddes limestone. Carbonaceous, flaggy limestone with some shale partings 335 MIDDLE (?) AND LOWER CAMBRIAN: Eldorado dolomite. Dolomite and limestone2,000 LOWER CAMBRIAN: Prospect Mountain quartzite. Quartzite with occasional inter calated conglomerate and shale 1,660+ The Prospect Mountain quartzite has been subdivided into two formations: Upper part, Pioche shale. Shale, quartzite with some intercalated limestone (Lower Cambrian fossils)-200 ft. Lower part, Prospect Mountain quart zite proper-I,460+ft. Total thickness6,695+] Much the most productive of these formations has been the Eldorado dolomite, which yielded more than $42,000,000 at Ruby Hill and an additional amount

Jan 1, 1947

By I. B. Browning, N. Shiarella, Coleman D. Hunter

The price of crude oil in Kentucky did not change very much during 1935 until the latter part of the year, but more stabilized conditions and an increase in consumption of natural gas made the year a more profitable one than the year 1934. The production of crude oil in 1935 amounted to 5,175,054 bbl. as compared to 4,814,904 bbl. in 1934. This increase was due to two developments: (1) the application of new recovery methods to old fields, which, although in operation in the state for several years, had never before reached a point where the production obtained, while highly satisfactory where applied, was sufficient to influence the totals in the production figures; (2) the development of the Fordsville area in Ohio County, where shallow depths enabled the operators to complete the development of a large number of wells with a good flush production probably accounted for most of the increase. A map showing the location of oil and gas pools in Kentucky was published last year.' The fields of eastern Kentucky, producing from the Weir sand of the Waverly group of the Lower Mississippian series, in Johnson, Magoffin, Lawrence and Elliott counties, produced 826,001 bbl. of oil in 1935 as compared with 902,247 bbl. in the previous year. No new wells were drilled in this area during the year, except those for use as intake wells in repressuring. What has been done in the few small areas within these fields in the way of repressuring has produced results sufficient to a great extent to offset the natural decline of all the field. It is probable the drilling of new wells and construction of new plants will be such as to cause these fields to produce more in 1936 than was produced in the past year. This is based on the fact that the sand is highly favorable for repressuring and the results obtained show from 300 to 500 per cent increase in production. From the "Corniferous" pools, where production is from the Cornifer-ous limestone of Devonian age, in Lee, Powell, Estill, Wolfe, Morgan and

Jan 1, 1936

By R. A. Hancock, L. C. Uren, G. V. Feskov, P. P. Gregory

The resistance to flow of mixtures of gas and oil in passing up through the flow tubing of oil wells operated by gas-lift or by natural flow is a factor in oil-recovery technic that has received but little attention. Yet accurate design of a tubing installation for a particular set of conditions, where operation is by either of these methods, is impossible without quantitative data on the pressure loss suffered by the oil-gas mixture in its passage through the well tubing to the surface. Because of lack of such information, petroleum production technologists have been compelled to approach this problem by " cut-and-try" methods, which, doubtless in many cases, has resulted in the installation and use of tubing too large or too small for most efficient utilization of the expansive force of the gas used in lifting the oil. Impressed with the necessity for information of this character, the authors have conducted a series of tests with large-scale apparatus in the petroleum engineering laboratories of the University of California, designed to be productive of data that would afford a means of attacking the problem of flow-tubing design on a more scientific basis. Mechanics of Expulsion of Gas-oil Mixtures in Naturally Flowing and Gas-lift Wells When oil is lifted from a well by the expansive force of compressed natural gas or air, the fluids enter the lower end of the eduction tube under elevated pressure, with the gas partly in solution, but largely distributed in the form of occluded bubbles within the oil mass. As discharged from deep wells, after reaching the surface, there will normally be at least 60 times as much gas, by volume, as of oil; and in many cases the ratio of gas volume to that of the oil will have a value as great as 1000 or more. On entering the lower end of the eduction tube, however, a relatively smaller volume of gas will be found in the oil-gas mixture, on account of compression of the gas in accordance with the elevated pressure necessary. If the pressure at the point of admission to the

Jan 1, 1930

By E. W. Edson, F. W. Hertal

In some fields the problem of mud fluid is simple and easy of solution. But in the Ventura Avenue field the acquisition and disposal of good drilling mud is not the least of the problems that confront the operator. In fact, mud fluid in the Ventura Avenue field is a very important factor in the drilling of the wells. It is quite probable that many of the factors affecting mud in this field will not be found in most of the fields with which the reader is familiar. However, in the fields where the mud fluid causes no apparent problem it is probable that some of the points brought out in this paper could be used to economic advantage. In fields where caving and squeezing formations and high gas pressures are present, as in the Ventura Avenue field, it is believed that application of methods outlined will be of great assistance in drilling wells. On account of the sandy nature of the formation and the lack of suitable shale bodies in the strata drilled through in the Ventura Avenue field, the wells make practically no mud during drilling. It is necessary therefore to supply drilling mud to the wells that will carry the drill cuttings to the surface, and also will " wall up" the drill hole and prevent the sandy formations from caving. Mixing and Handling Mud Fluid The clay used to make the mud fluid is obtained from a shale stratum in the upper Pico (Plioccne) formation found about a mile on either side of the field. Since high gas pressures and caving formations were first encountered in the Ventura Avenue field and mud fluid was needed to combat them, the mixing of this mud fluid has gone through a process of evolution. First, the clay was mined and hauled to the derrick, where it was shoveled into the well and left for the churning action of the bit to mix into a mud in the hole. The next move was the construction of a mixer to mix the clay to a mud fluid which was pumped into the well. These mixing

Jan 1, 1930

By E. W. Krampert

Oil development continued active in Wyoming during 1937, with much of the interest centered on prospecting for new pools, following a rather intensive seismograph play in 1936. The new fields of Lance Creek, Medicine Bow and Quealy were the centers of intense development in proved areas, but routine drilling occurred in most old fields. A new and deeper producing horizon (the Leo sand) was opened up in the Lance Creek field, which materially extends the producing area and will probably account for continued active development during 1938. The discovery in 1936 of oil in the Eocene Wasatch formation at Powder Wash, northwestern Colorado, tended for a time to stimulate prospecting in the deep Tertiary basins, but this interest as rapidly declined after drilling several failures on similar structures and the discovery that the productive area at Powder Wash itself was very small. A most interesting test of an Eocene structure was drilled by The Superior Oil Company of California on the South Baggs structure, in Carbon County, Wyoming. South Baggs is one of the best developed structures in the Red Desert Washakie Basin, which also includes the Hiawatha gas field and the Powder Wash gas and oil field. The Superior Oil Co. started the well according to contract but apparently had lost interest in the prospects, for it abandoned the well at 2138 ft. without testing the oil-bearing and gas-bearing horizons of the Wasatch. The Sinclair Wyoming Oil Co. drilled a deep test in the Muskrat gas field to the Madison. This well discovered oil in the Embar formation, which was considered noncommercial because of depth. After the Embar was abandoned the hole was plugged back and the various sands tested by shooting through the casing with the Lane-Wells gun. The Lakota sand was found to contain high-pressure gas and the well was completed as a 24-million-foot gasser at 2175 lb. rock pressure. This is a new sand in an old field. The Italo Petroleum Co. drilled a flank well on the Hamilton dome structure and found oil in the lower Embar formation. Thk merely extends the limits of production, as one old well on the structure had

Jan 1, 1938

By George Watkin Evans

The need for mechanization in coal mining wherever it can be successfully introduced is evident when we take into account the fact that during recent years the coal-mine employee's wages have increased and his hours have been shortened. Coal is no longer King, and a brief study of statistics covering the production of coal, petroleum and natural gas and the development of water power will convince anyone that coal has had very powerful competitors during the past 10 years. Petroleum production in the United States between 1918 and 1936 increased from 100 per cent to 309 per cent. Water power increased from 100 per cent in 1918 to 270 per cent in 1936. Bituminous coal slipped from 100 per cent in 1918 to 75 per cent in 1936. The anthracite industry slipped from 100 per cent in 1918 to 50 per cent in 1932, but climbed to 55 per cent in 1936. In 1918, the State of Washington produced a little over four million tons of coal and the production of California oil, at that time, was a little less than one hundred million barrels per year. By 1929 the production of California oil had increased to a little over 292,000,000 bbl. or nearly 300 per cent as compared with 1918. By 1934 the production of coal in the state of Washington had dropped to about 1 1/3 millions of tons per year. Our neighbors in British Columbia had their coal production reduced from a little over 2 1/2 million tons in 1920 to less than 1 1/3 million in 1933. The North western Improvement Co., a subsidiary of the Northern Pacific Railroad Co., owns coal properties in various parts of Washington and Montana. The Northern Pacific is one of the very few railroads using any considerable quantity of coal in its operations. Practically all of the American railroads in the Pacific Northwest, except the Northern Pacific, are using cheap California fuel oil or electricity. This problem, of course, is not a new one in coal mining, and all of the progressive coal companies in the country have tried to meet competition from an overproduction of petroleum and an overproduction of natural gas as well as enlarged developments of hydroelectric plants.

Jan 1, 1938

By Theron Wasson

The state of Michigan showed considerable activity during 1935. The center of greatest interest was the Crystal field, which was unknown until March, 1935, and is an illustration of the effect of the unknown and unexpected on Michigan oil development. The fields of the state (Fig. 1) produced a total of 15,770,000 bbl. of oil in 1935, or about 5 million more than in 1934. In order to keep up this production 307 new oil wells were drilled, of which 88 were in the Crystal area, which produced 3,600,000 bbl. This field had a rapid development and reached its peak in October. Since that time increasing water encroachment has caused a rapid decline. The pay horizon at the top of the Monroe dolomite is only a few feet thick. Big producers were offset by dry holes or small wells. The discovery well, which was in section 11, Crystal township, Montcalm County, was drilled March 28, 1935. Its initial production was 5000 bbl. per day, and up to Dec. 31, 1935, had produced 350,000 bbl. of oil—dose to one-tenth of the total production of the field to that date. The Beaverton field, which was discovered at the close of 1934, did not develop rapidly. Four small producers were finished in the Dundee lime during the year. West Branch was active and at the end of the year had 97 producers, 72 of which were drilled during 1935. Most of the wells produce from the Dundee lime; a few are finished in the Traverse. The Birch Run field deserves special mention, for it is the one area where consistent production continues to be found in the Berea sand at about 1500 ft. Wells are small, 20 now producing a total of about 300 bbl. per day of oil of fine quality. The old Central Michigan producing area, extending from Nit,. Pleasant through Yost to Porter, continued to be the principal producing area of the state and accounted for 10,370,000 bbl. from 660 producing wells. Ninety-three new wells were drilled in this territory. The Porter field, at the southeast end of this producing trend, was outstanding from the standpoint of production. The old Leaton field of Isabella County added several new producers. Its production was greater than in 1934.

Jan 1, 1936

By A. H. Bell

The results of repressuring (or gas-drive) have been very encouraging to the several companies doing experimental work along these lines in California. The most notable examples are the Shell and the Union Oil companies at Dominguez, the Marland Oil Co. at Seal Beach, and the California Petroleum Corpn. at South Mountain. The results of the Marland test at Seal Beach are interesting in that re pressuring was started while several wells were still flowing; also, on account of the high pressures required to overcome the hydrostatic pressure exerted by high-head edge water. The well first chosen for repressuring is about halfway up the flank of the structure and had been on the beam making about 250 bbl. of fluid daily, cutting about 60 per cent. emulsion. The fluid lcvel was 230 ft. from the surface and the top of the sand was 4393 ft. Tubing was run to 4000 ft. with a packer and the space above the packer was filled with water to balance the high pressures. Gas was started in slowly to allow the fluid to be pushed back into the sand, and required three days at a pressure of 1500 Ib. per sq. in. before starting into formation. The pressure was once built up to 1800 Ib. and the compressor was shut down for a few hours. When again started, the well took gas at 1500 Ib., and after about three weeks the pressure was dropped to 1450 Ib. The present pressures required range between 1400 and 1450 lb. Volumes as high as 1,500,000 cu. ft. per 24 hr. were put into the well. Increases as high as 50 per cent. in production were obtained in wells up-structure with very little increase in wells down-structure. Also, the water cut on one edge well materially decreased. After about 40 days the repressuring was moved to two wells farther down-structure and the well originally repressured was put on production. The result of this was a great increase in the production of wells one location farther down-structure, a rapid increase in one well one location up-structure, and a decrease in production of the wells farthest up-structure. Later the gas started to short-cut to the nearest well down-structure, nullifying to a certain extent the effects of the repressuring work. The increased production that could be definitely attributed to the repressuring work

Jan 1, 1928

By Casimir Constable

DURING the years 1875 to 1879 I had charge of the Rockwood furnaces and mines, situated forty miles from the nearest railway communication at that time, and one hundred miles north of Chap tanooga, Tenn., by the Tennessee River. The small furnace with old-fashioned stoves, then in blast, was built under great difficulties by General Wilder. The early conditions were somewhat as follows: The ore was fossil ore of the Clinton group ; very fine and generally wet, without other admixture. The coke had a large amount of ash, and the fur" nace appeared to be badly scaffolded at times. On many days only a few tons of iron could be obtained. The founder generally id creased the revolutions of the engine when signs of chilling appeared,. The cinder at such times was black, very scoriatious, often closely resembling mill cinder. When the pressure was increased (the joints being the old-fashioned rust joints), leaks in the blast-pipe occurred It was noted that when the blast was stopped, and the leak bolt imperfectly remedied, the furnace improved a little. This set me thinking on the right track; and I took the responsibility of be coming my own founder for a time. A scaffolded condition had existed, and the situation was a trying one. Strange to say the negroes proved excellent furnace-men. Conceiving the hearth of the furnace to be similar to the grate area of a steam-boiler, capable of disposing of but so much fuel per hour, and requiring only a corresponding amount of air, it follows that an excess of air will burn the fuel not yet arrived at the hearth!, and raise the melting-point far above the tuyeres. This might pro duce scaffolding or at any rate choke the boshes, and leave less fuel to be consumed in the hearth. Thus for the time being less ail;. would be needed, as the continued burning of fuel in and above the boshes, would only aggravate the trouble. This condition of affairs accounted for the black cinder; the heat above having melted ore not yet perfectly reduced. This view decided me to reduce the revolutions of the engine; thefurnace finally became gray, as might have been expected. Any attempt to increase the speed produced black cinder and hard iron ;

Jan 1, 1883

By Bailey Willis

IN 1882, Peckham put forward a provisional hypothesis to account .or the distillation of petroleum.1 He did not formally state the hypothesis, but in a discussion of facts drawn from many fields he made it clear that he regarded petroleum, and especially the petroleum of the Pennsylvania fields, as a "fractional distillate produced under high pressure and consequently at a comparatively high temperature.?2 He quotes James Hall on the geology of the Appalachians and says:3 It is not necessary here to discuss the nature or origin of metamorphic action. It is sufficient for our purpose to know that from the upper Silurian to the close of the Carboniferous periods the currents of the primeval ocean were transporting sediments, sorting them into gravel, sand, and clay, forming gravel bars and great sand beds beneath the riffles and clay banks in still water, burying vast accumulations of sea weeds and sea animals far beneath the surface. The alteration, due to the combined action of heat, steam, and pressure, of the formations of the Appalachian system from Point Gaspe in Canada to Lookout mountain in Tennessee, involving the Carboniferous and earlier strata, distorting and folding them, and converting the coal into anthracite and the clays into schists along their eastern border, could not have ceased to act westward along an arbitrary line, but must have gradually died out farther and farther from the surface (source?). The great beds of shale and limestone containing fucoids, animal remains, and even indigenous petroleum must have been invaded by this heat action to a greater or less degree, and that "chronic evaporation" of Prof. Lesley must have been the inevitable consequence. From an investigation of the relations between coal and petroleum, White has" more recently concluded as follows: (1) Petroleum is a product generated in the course of the geodynamic alteration of deposits of organic debris of certain types buried in the sedimentary strata. (2) The quantity and characters of the oils generated are determined by: (a) the composition of the organic deposit at the beginning of its dynamo-chemical alteration; (b) by the stage in the progress of the dynamo-chemical alteration of the organic substances; (c) by the elimination, under certain conditions, of the heavier and more' viscous hydrocarbons through filtration incident to migration.

Jan 1, 1920

By Persifor Frazer

MR. Theodore D. Rand has made some interesting observations on the serpentines of Chester and Delaware counties, Penna., in which he suggests that the outcrops of this rock are detached from each other, and that while a comparatively narrow belt, running nearly east and west, mill include them all, the strike of each outcrop differs considerably from the direction of this narrow belt; and that it results that these isolated exposures exist on the map, as it were, in echelon, the easternmost end of each lying northwest of the western extremity of its neighbor. As he elsewhere remarks, this is important, if established, and the writer spent a day or two recently on the ground in the study of this phenomenon. One thing would seem to follow from such a state of facts, viz., that this serpentine at least must have been of secondary origin, for it is difficult to conceive of a rock which occurs intercalated in numerous horizons of a different formation, and agreeing with the latter in bedding, unless the former were an altered product of the latter. It is true that one might account for it by the supposition of an original unconformable deposit, which had been broken by a number of faults and distorted by throws to the northwest; but this hypothesis would do violence to the observed facts relating to the measures along with which the serpentine occurs, and in which no such distortion has been observed. * Thus for determining, by evaporative test, the calorific power of a coal, the ultimate constitution of which is known, it is requisite, that, besides the quantity of coal consumed and the weight of the water evaporated, the temperature and chemical composition of the escaping gases, or gaseous residue, shall be quantitatively determined, the same as solid residues of ash and unconsumed fuel. In observance of such requirements, the Heizversuchstation of Munich has been in operation since 1879. This consists of a permanent boiler plant, constructed on the principle of the calorimeter, with special provision for avoiding errors from loss of heat—snch, namely, as arise from radiation and conduction, and from the varying proportions of water in steam.—Muck. Steinkohlen-Cliemie, 1881, 146. See Proc. Min. and Geol. Sect., Acad of Nat. Sci., 1850 and 1881, pp. 9 and 28.

Jan 1, 1884

By William Kent

About a year ago, the writer had occasion to assist Mr. John L. Gill, Jr., of the Pittsburgh Car-wheel Works, in malting a trial of his new testing machine. A piece of Bessemer steel, of about .34 carbon, was used as a test-piece, turned to a sectional area of one square inch for a length of five inches between shoulders, and provided with large round heads, which were fitted to what is called the " Wade grip." Measurements of elongation, accurate to 1/10000 of an inch, were made by a special apparatus containing two micrometer screws, with electric contact attachment. The machine was operated by hand-power. Readings of elongation were taken at each increment of 2000 pounds stress per square inch, up to 44,000 pounds, the elongation corresponding to the latter figure being .0085 inch. The elongations up to this point remained almost exactly proportional to the stresses, the strain diagram, as shown on the Plate, from the origin to the point A, being a straight line (the deviation of no observation from the straight line being greater than .0002 inch). There being no indication of an approach to the elastic limit, the attendant at the hand-wheel and scale-beam wits told to proceed as usual and move the poise forward 2000 pounds, or to 46,000, and turn the wheel until the beam was balanced. Noticing that the beam did not rise in the usual time, and that the elongation was increasing rapidly, the writer called to the attendant to stop turning the hantl-wheel and to push the poise backwards until the scale-beam balanced. Instead of balancing at between 44,000 and 46,000 pounds, as was expected, it balanced at 40,000 pounds, and the elongation had increased to .0343 inch (or more than four times that recorded at 34,000 pounds), as plotted at the point B, the dotted line between A and B showing the supposed course of' the strain diagram between these two points. Immediately upon recording the elongation the writer said to Mr. Gill, who was standing alongside: "This phenomena is without a parallel in my experience, and I know of but one way to account for it. The piece. must actually be broken in its interior, through a flaw or weak portion of the metal. The test-piece is now equivalent to a tube, with

Jan 1, 1880

By J. E. Lawver, G. L. Samsel

The success of many mineral dressing processes, including froth flotation and electrical concentration, depends largely on knowledge of physical and chemical structures of the mineral surfaces involved. As a general rule solids have surface layers, usually invisible by optical tests, that differ from the substratum. To the mineral engineer, therefore, a knowledge of the surface structures of minerals is of paramount importance. During the past decade one of the most powerful tools in the study of froth flotation mechanisms has been the use of radioactive tracers, but this technique usually cannot give definite information regarding the chemical changes that may or may not have occurred at the surface. The electron microscope and electron diffraction camera can be particularly useful instruments in surface studies.. An election microscope permits much closer examination of surfaces than can be obtained with a petrographic microscope. In certain cases, it is possible to identify trace quantities formed by chemical reaction between flotation agents and mineral surfaces by the use of a single-crystal, reflection electron diffraction camera. This article describes several instances in which these instruments have been valuable guides in mineral dressing research at International Minerals & Chemical Corp. One of the first applications of these techniques employed by International Minerals was in conjunction with the study of electrical concentration of potash ore. The first reasonably successful separation of potash ore was made by subjecting a sample of the ore to a methanol wash. Subsequent tests using tagged 6C14 methanol showed that only a minute quantity of radioactivity was detectable after the methanol-washed sample had been dried and heated to about 300°F. It was concluded that although some methanol had been held to the surface by adsorption, this could not account for the improved electrification because there was no evidence of methanol selectivity with respect to NaCl or KCl. Consequently there must have been some other change in the surface. Carbon replicas* of the mineral grains were made before and after the methanol wash. The replicas were separated from the minerals by dissolving in water. This extraction replica technique is particularly attractive because the specimen can first be used with the electron microscope to observe the general structure of the surface and can be re-used as a specimen for electron-diffraction studies to identify any solvent insoluble material present on the mineral surface." Fig. 1 shows the general

Jan 1, 1960

By Lawrence Addicks

Some three years ago the smelter connected with the Chrome, N. J., refinery of the United States Metals Refining Co. found itself embarrassed by constantly increasing piles of unsmelted blast-furnace flue dust. The charge was fine and 10 to 15 per cent. of it was blown over into the flue. Sulphur was at that time too scarce to make the sintering of the finer part of the charge attractive, and raw-ore smelting in a reverberatory with a partly oxidized charge was not to be thought of. A great many schemes were considered, including leaching, blowing into the converters, and briquetting, the problem finally narrowing down to blast roasting and nodulizing. It was found by experiment that blast roasting would not yield a satisfactory sinter without the addition of coke dust or sulphide fines to augment the fuel value of the flue dust, and on this account, together with the low first cost of a kiln, the latter was decided upon. A couple of tons of flue dust were tried out in the experimental kiln in the laboratory at Yorktown, Va., of J. H. Payne, who acted as consulting engineer in this connection. This kiln was approximately 2 ft. in diameter and 20 ft. long and was fired with fuel oil. A run of several hours yielded excellent nodules. The ki1n showed no tendency to build in and form "nose rings" and gave a fuel consumption of 50 gal, of oil per ton of flue dust. There was no indication of any stack loss. The roasting was strongly oxidizing. A study of what full-size kilns were doing on cement clinker and on nodulizing pyrites cinder indicated that a 60 by 6 ft. kiln would certainly not consume over half of the oil per ton of flue dust shown on the test and as fuel oil at that time was selling around 2 1/2 c. per gallon it was decided to let it go at that. A 60 by 6 ft. kiln was decided on, as that size is standard in cement practice, although fast being replaced by much larger ones with their greater fuel economy, and as it fitted in the building space available. A 6-in. brick lining brought the net diameter down to 5 ft. The inclination

Jan 1, 1915

By E. D. Peters

It frequently occurs in the establishment of reduction works, in an entirely new and untried mining district, that the metallurgist in charge finds considerable difficulty in determining the process best adapted to the ores which he receives for treatment. At the first glance it would seem easy enough to decide what style of furnace is best adapted for beneficiating any one class of minerals. If the ore possessed a quartzose gangue and was comparatively free from base metals, while salt could be obtained at a reasonable price, one would naturally resort to a chloridizing roasting, and pan or barrel amalgamation for the extraction of its silver contents. If galena or carbonate of lead was the prevailing mineral, and charcoal could be obtained at moderate figures, the blast-furnace would beneficiate the ores most advantageously. But if, as is usually the case in Colorado, the ores consisted of an intimate mixture of galena, zinc-blende, copper-pyrites, and noble silver minerals, associated with an overwhelming mass of siliceous heavy spar, or limestone gangue, the common reverberatory furnace can be used to the greatest advantage ; and, although the product is only a copper matte, I do not hesitate to affirm that it can be treated, and the silver, gold, and copper produced at nearly the same price for which silver and lead can be separated. In Germany, blast-furnaces are frequently used for this same purpose, both for argentiferous and non-argeutiferous copper ores; but any one who will take the trouble to examine the statistics of smelting at Fahlun, the Oberharz, and other Continental works of this description, will see that the expenses are far too great, and the production much too small to think of employing this method in our mining districts, where only the softest and most miserable kind of charcoal is obtainable. I propose in this paper to give an accurate account of the expenses incurred at the Mount Lincoln Smelting Works in treating the same kind of ore, and producing the same end-product in both blast and reverberatory furnaces. I have taken for comparison a favorable campaign of the blast-furnace, and a good average month's running of the reverberatory. In the blast-furnace estimate I have included the calcining and concentration of the matte produced during that campaign, as I always, when possible, concentrated the regulus made

By F. C. Miller

The metallurgical fuel of Colorado, Utah, and New Mexico has been a Veiny tardy member in the caravan of western industrial progress. The history of western coke has naturally been closely related to the development of the metallurgy of iron and steel and the precious metals, in the State of Colorado. It was at Leadville, with a population of 300 in 1877, that the Sentinel was published by Richard S. Allen. The Sentinel gave very full accounts of the various mineral discoveries at the new town of Leadville, which found their way to the more widely circulated journals of the East, and attracted the attention of many people. At the close of 1878, a census slowed a total of 5040 persons. The first smelter was established in 1877, at Malta, two miles from Leadville, by A. R. Meyer, but was not successful. It was succeeded by the Harrison Reduction Works, in 1878. The La Plata began with one furnace in June, 1878, and in 1879 had four furnaces in active operation. These furnaces used charcoal for fuel, and, because of hot tops, suffered a tremendous loss in lead and silver. This difficulty was overcome by the erection of 50 single-bank 10-ft. beehive ovens at Crested Butte, Colo., in 1880. The slack coal sent to these ovens was very pure, and yielded a coke carrying as little as 4.5 per cent. ash. Among the pioneers in the Leadville district were Grant, Eddy, James, Billings, Eiler, and Dickson. To these men the West owes the present expansion of its mining industry, and the erection of metallurgical processes for the treatment of precious metals. On Mar. 1, 1876, Pueblo was connected to the Atchison, Topeka & Sank Fe by the Pueblo & Arkansas Valley branch. The first smelter was erected in Pueblo by Mather and Geist. This modest plant grew into the immense Pueblo Smelting and Refining Co., now a part of the American Smelting and Refining Co. Coke for these small furnaces was made from unwashed Engleville coal, in 186 single-bank 12-ft. ovens at El Moro, in the Trinidad district, and it was not uncommon for the percentage of ash to exceed the percentage of fixed carbon in the coke. On Jan. 23, 1880, the Colorado Improvement Co. consolidated

Jan 1, 1920

By George Watkin Evans

The need for mechanization in coal mining wherever it can be successfully introduced is evident when we take into account the fact that during recent years the coal-mine employee's wages have increased and his hours have been shortened. Coal is no longer King, and a brief study of statistics covering the production of coal, petroleum and natural gas and the development of water power will convince anyone that coal has had very powerful competitors during the past 10 years. Petroleum production in the United States between 1918 and 1936 increased from 100 per cent to 309 per cent. Water power increased from 100 per cent in 1918 to 270 per cent in 1936. Bituminous coal slipped from 100 per cent in 1918 to 75 per cent in 1936. The anthracite industry slipped from 100 per cent in 1918 to 50 per cent in 1932, but climbed to 55 per cent in 1936. In 1918, the State of Washington produced a little over four million tons of coal and the production of California oil, at that time, was a little less than one hundred million barrels per year. By 1929 the production of California oil had increased to a little over 292,000,000 bbl. or nearly 300 per cent as compared with 1918. By 1934 the production of coal in the state of Washington had dropped to about 1 1/3 millions of tons per year. Our neighbors in British Columbia had their coal production reduced from a little over 2 1/2 million tons in 1920 to less than 1 1/3 million in 1933. The North western Improvement Co., a subsidiary of the Northern Pacific Railroad Co., owns coal properties in various parts of Washington and Montana. The Northern Pacific is one of the very few railroads using any considerable quantity of coal in its operations. Practically all of the American railroads in the Pacific Northwest, except the Northern Pacific, are using cheap California fuel oil or electricity. This problem, of course, is not a new one in coal mining, and all of the progressive coal companies in the country have tried to meet competition from an overproduction of petroleum and an overproduction of natural gas as well as enlarged developments of hydroelectric plants.

Jan 1, 1938

Discussion of the paper of O. P. Hood, presented at the Pittsburgh meeting, October, 1914, and printed in Bulletin No. 94, October, 1914, pp. 2607 to 2611. R. V. Norris, Wilkes-Barre, Pa.-I have had a little experience with gasoline locomotives and I want to indorse very strongly Mr. Hood's point with regard to the danger of carbon monoxide poisoning. I think .the terrible danger is not fully realized. I was foolish enough some time ago, in investigating a gasoline locomotive, to attempt to walk out of the mine entry behind it, and for several days I felt very seriously the carbon monoxide effects. The use of gasoline locomotives ought to be confined to mine entries where there is a very large amount of air. One of the grave dangers is their great convenience and the temptation to run them into chambers for just a few moments to get a car or two. GEORGE S. RICE, Pittsburgh, Pa.-Apparently one of the great dangers is in the style of the gasoline engine. When my attention was. first directed to the type of gasoline locomotives which I saw in the foreign mines-France, Belgium, and Germany, I was most favorably impressed with them, and they have given no trouble on account of fumes, so far as I could learn. Large numbers of them were being used, but all were of small capacity, and of a kind in which the speed control is by a governor of the hit-or-miss type, the engine running continuously. Their power capacity was very low, if I remember correctly it was not over 4 or 5 h.p., but they were used under favorable conditions where the grades in the mines were slight, since the entries or tunnels bad a slight grade in favor of-the load, making about the same pull for the empties against the grade as for the load with the grade. I understand the hit-or-miss valve arrangement enables a setting that will give more perfect combustion than can be insured with the valve controlled by the operating man, as in the automobile type of valve and engine used in this country. Apparently the European type of locomotive does not have the capacity to permit use under the conditions existing in this country, where most of our entries or tunnels have variable grades and long heavy trips of mine cars are used.

Jan 4, 1915