Search Documents

By R. S. Dean. J. R. Long T. R. Graham, Roberson A. H., Armantrout C. E.

The general program of the Federal Bureau of Mines on the study of alloys made with electrolytic manganese has been extended to copper-manganese-aluminum alloys. The initial results of the work are presented in this report and concern a determination of the mutual solubilities of these three metals to form the alpha solid solution. The principal studies of this system, reported in the literature, have been focused on the Heusler alloys containing ro to 30 per cent Mn with 9 to 15 per cent Al. These investigations concern the ferromagnetic properties and the determination of the crystallization contours, with little emphasis on the phases present in the solid state outside of this area. Heuslerl recognized a breakdown of the beta solid solution of the magnetic alloy, which he says decomposes into the alpha, beta, and gamma phases of the copper-aluminum system, somewhat modified by the presence of manganese. Rosenhain and Lantsberry2 examined alloys ranging up to 10 per cent Mn and 10 per cent A1 but were unable to reach definite conclusions concerning the phase boundaries in that area. Krings and Ostmann3 made magnetic studies and examined the system by thermal analysis. They present contours of the liquidus surface but do not place any of the phase boundaries. Corson4 has drawn a hypothetical boundary for the alpha field with few, data to support such construction. The binary systems involved have rcceived considerable attention by numerous investigators, and their general features are well established. The copper-ahminum system (Fig. I) has been thoroughly examined by Stockdale,5 who places the limit of solubility of aluminum in copper at 7.4 per cent at the liquidus and 9.5 per cent at room temperature. Smith6 established the eutectoid temperature at 570°C. by a study of isothermal decomposition of the beta phase. The copper-manganese system (Fig' ') has been recently reviewed by Dean and CO-WorkersS.7 Using high-purity alloys,

Jan 1, 1947

By Harry K. Ihrig

The hot-working of iron and steel is an art dating back to antiquity, but until about 25 years ago, relatively few alloying elements were used, and these were present only in small percentages. With the exception of sulphur, the amounts of other elements in steels did not markedly affect their hot-workability. The references in the literature on the effect of other elements on the hot-workability of steel are usually reports of failure of these steels in forging or rolling.1-8 With the increased use of alloying elements, and their use in larger amounts, it was observed that many of the new steels were red short in certain critical ranges or at all hot-working temperatures. The stainless steels are particularly difficult to hot-work. The determining of the correct conditions for piercing, rolling and forging of these alloys by experimentation in the mill often results in large losses of these expensive metals. It also is found that the hot-workability limits of many types vary from heat to heat, and hence poor results are obtained on changing to a new heat after a previous one has rolled satisfactorily. To determine the effect on hot-workability of iron to which various elements have been added, it was necessary to devise a method that could be used on small quantities of metal. In such a method, the minimum number of variables should be present, and the procedure should be simple, quick and correlatable with large-scale hot-working operations. Sauveur,9 in the first Henry Marion Howe lecture in 1924, described the effect of carbon on the ductility of steels in torsion near their critical points. He found that carbon increases the plasticity of gamma iron. In the 1930 Campbell Memorial lecture,10 he gives the effect of carbon, chromium, and chromium and nickel on the ductility of steels under 2000°F. in torsion. Ellis11 has studied the malleability of steels at various elevated temperatures by means of a single-blow drop-hammer test. In this test the percentage decrease in height of standard cylinders is taken as a measure of their malleability. He has shown that in the low-alloy steels studied, carbon has a greater effect than nickel, chromium and vanadium. In 1938 the first tests were run on a new quantitative hot-workability test in the laboratories of the Globe Steel Tubes CO. Thum12 mentioned it in 1940. An illustration of the apparatus was published in January 1942.'' The effect of a few alloying elements on the hot-workability of metals was shown in a description of the test in 1944.14 Description of Test Method The method adopted after a trial of several others is a rapid twisting of bars to failure in a furnace. The standard-size bar was chosen as 9/16 in. It is prepared from larger pieces by forging and cold-

Jan 1, 1947

By J. W. Bolton, S. A. Weigand

This paper discusses some fundamental metallurgical principles involved in production of sound cast bronze. In a previous paper the writers advanced the theory that "oxidation" in bronze castings is due to incipient shrinkage, and showed the effect of reducing melting atmospheres.' In the present paper the effects of certain impurities and of actual oxidizing conditions are shown. The appendix deals with the appearance of various inclusions. For many years the prevailing opinion has been that unsoundness, dark colored fractures and other phenomena accompanying porosity and weakness in bronzes are due to oxidation. The actual troubles are caused by fissures of intercrystalline type, which are often mistaken for intercrystalline films. These weaken the metal and make it porous. Grave doubt regarding the accuracy of the oxidation theory appears when several research papers presented within the last 10 years are reviewed critically. In 1919, Comstock2 conducted metallographic researches, attempting to identify "oxides" in synthetically prepared metals. He found that oxides of tin, aluminum, zinc, etc. are different from the intercrystalline films (or cavities) to which porosity is due. Apparently he believed that these "oxide films" may be caused by volatile oxides of zinc or of phosphorus or by dissolved gases thrown out of solution during solidification of the metal. In 1923, Woyski and Boeck3 definitely questioned the accuracy of the oxidation theory and indicated the danger from reducing atmospheres. They say that "oxidation, gassing and shrinkage may produce effects very similar." In 1926, investigations by Iwasé4 showed marked change in absorp-tion coefficients for various gases in copper above and below the liquidus.

Jan 1, 1930

By L. H. Robinson

Triaxial compression tests have been performed to determine the strength characteristics of limestone, sand-stone and shale rocks subjected to controlled stress conditions. This control tuns exercised by varying the liquid pressures within and around a plastic-encased rock specimen. The pressure in the pores of the rock was varied throughout the range from atmospheric to 15,000 psig; the external pressure was changed over the same range with various positive pressure differences between is and the intertnal pressure. The data show that the rock strength increased and the mode of failure changed as the pressuire. surrounding the rock became greater than the pressure in the pores of the rock. These observations and the resu1ts of microbit drilling experiments indicate that the increased rock strength under pressure may bc an important effect in reducing drilling rare, but that other factors are probably of even greater importance. INTRODUCTION A large part of the research conductcd to reducc thc cost of drilling is directed toward improving present drilling technology and dcveloping new drilling methods. In spite of the fact that drilling is essentiaIly the act of making rocks fail, many details of the mechanism of failure are not known. It seems probable, therefore, that continuing studies of the fundamentals of rock failure can lay a foundation for future improvements in drilling technology. One of the factors which affects rock failure is the stress applied to the rock. This effect has been known for many years.'.'.; As an example, stress studics have been published by engineers' concerned with the strength characteristics of concrete in large dams. More recently, a number of investigators4-12 have explored the effects of stress on the strength of geologic formations and the geologic implications of their findings. During the last few years some research'" on rock strengths has also been conductcd in an attempt to gain additional insight into the factors which affeet rock drillability. In detcrmining the strength characteristics of rocks under different stress conditions, investigators have conventionally used triaxial compression equipment. wherein a jacketed rock cylinder is uniformly loaded from all directions and then compressed longitudinally. The results of this work have demonstrated that the mode of failure (brittle or malleable) is dependent upon the loading pressure, and that the strength of the rock increases as the loading pressure increases. These results clearly manifest that the stress, which is determined by the loading pressure, affects rock strength, and this implies that rocks under stress should be stronger and hence harder to drill. During the drilling of a porous rock the stress conditions are determined not only by the pressure surrounding the portion of the rock undergoing failure (confining pressure) but also by the pressure of the interstitial fluids within the rock (pore pressure). The importancc of both these pressures on the drilling rate of rocks has already been demonstrated by a number of investigators. Murray and Cunningham" found in microbit drilling expcriments that at constant pore pressures the drilling ratc decreased as the hydrostatic pressure surrounding an unjacketed, impermeable rock increased. Later Eckel" found that for jacketed Iimestone specimens the differcnce between hydrostatic (wellbore) pressure and formation (pore) pressure had an important effect on drilling rate. These observations of the effect of pressure on drilling rate emphasize that for drilling studies triaxial compression tests should be conducted under conditions of confining and pore pressure which simulate conditions underground. In the past, triaxial tests have been made under conditions which do not reproduce those underground. In particular, most of the tests on porous materials have keen made at varying confining pressures but with atmospheric pore pressures. In only one group of tests' was any data on the effect of pore pressurc reported, and these few data were on materials not representiltive of those encountered in drilling earth formations. The research described herein was initiated to deter-mine the importance of both internal pore pressure and confining pressure on failure characteristics of limestone. sandstone and shales. Triaxial loading equipment was used to obtain strength data at pressures up to 15,000 psig. An additional objective of this research was to apply these results to drilling rate studies by comparing them with the previously published drilling data of Murray and Cunningham" and of Eckel12. The work reported here is but one step in determining and evaluating the fundamental mechanisms which control drilling rate. Additional research is needed to clarify other aspects of the drilling process. The better

By Armantrout C. E., R. S. Dean. J. R. Long T. R. Graham, Roberson A. H.

The general program of the Federal Bureau of Mines on the study of alloys made with electrolytic manganese has been extended to copper-manganese-aluminum alloys. The initial results of the work are presented in this report and concern a determination of the mutual solubilities of these three metals to form the alpha solid solution. The principal studies of this system, reported in the literature, have been focused on the Heusler alloys containing ro to 30 per cent Mn with 9 to 15 per cent Al. These investigations concern the ferromagnetic properties and the determination of the crystallization contours, with little emphasis on the phases present in the solid state outside of this area. Heuslerl recognized a breakdown of the beta solid solution of the magnetic alloy, which he says decomposes into the alpha, beta, and gamma phases of the copper-aluminum system, somewhat modified by the presence of manganese. Rosenhain and Lantsberry2 examined alloys ranging up to 10 per cent Mn and 10 per cent A1 but were unable to reach definite conclusions concerning the phase boundaries in that area. Krings and Ostmann3 made magnetic studies and examined the system by thermal analysis. They present contours of the liquidus surface but do not place any of the phase boundaries. Corson4 has drawn a hypothetical boundary for the alpha field with few, data to support such construction. The binary systems involved have rcceived considerable attention by numerous investigators, and their general features are well established. The copper-ahminum system (Fig. I) has been thoroughly examined by Stockdale,5 who places the limit of solubility of aluminum in copper at 7.4 per cent at the liquidus and 9.5 per cent at room temperature. Smith6 established the eutectoid temperature at 570°C. by a study of isothermal decomposition of the beta phase. The copper-manganese system (Fig' ') has been recently reviewed by Dean and CO-WorkersS.7 Using high-purity alloys,

Jan 1, 1947

By C. S. Giggins, F. S. Pettit

The oxidation properties of Ni-Cr alloys with fine grains, coarse grains, and deformed surface layers have been studied at temperatures of 900" and 1100°C in 0.1 atm of oxygen. The oxidation rates of alloys containing between 10 and 30 wt pct Cr have been found to be dependent upon the grain size of the alloy. Finegrained alloys had smaller oxidation rates than coarsegvained alloys because of the selective oxidation of chromium at alloy grain boundaries. In this compositional range alloys with deformed surface layers behaved similar to fine-grained alloys due to recrys-tallization of the deformed surface layer. In the preceding paper1 it was found that during the oxidation of Ni-Cr alloys, the volume fraction of precipitated Cr2O3 could be greater at alloy grain boundaries than at other areas of the alloy surface. In the case of alloys with chromium concentrations equal to or greater than 30 pct,* the volume fraction of Cr2O3 *AIL compositions are given as weight percent unless specified otherwise. precipitated at grain boundaries and within grains on the alloy surface both exceeded the critical amount required for lateral growth of the Cr2O3 particles and the surfaces of these alloys were completely covered with a continuous, external layer of Cr203 during oxidation. However, in the case of alloys with chromium concentrations between approximately 5 to 30 pct, the volume fraction of precipitated Cr2O3 exceeded the critical value required for external scale formation only at grain boundaries.but not within the interior of the grains. Consequently, the surfaces of these alloys had external scales of Cr3O3 over the grain boundaries but internal Cr2O3 subscales with external scales of NiO away from the grain boundaries. Under these latter conditions, it was found that chromium could diffuse laterally in the alloy from those areas covered with an external layer of Cr2O3, i.e., grain boundaries, to areas where the Cr2O3 was present as a subscale. This diffusion of chromium resulted in an increase in the volume fraction of Cr2O3 precipitated in the sub-scale zone and continuous layers of Cr2O3 could be formed at the subscale front in these regions. For the alloys used in the previous studies,' continuous layers of Cr2O3 were formed on Ni-20Cr alloys in the subscale regions after approximately 30 hr of oxidation at 900°C. For shorter periods of oxidation, the Cr2O3 layer was semicontinuous with the continuous portion at the subscale front emanating from points where the Cr2O3 had been formed as an external scale over alloy grain boundaries. Some lateral growth of a Cr2O3 layer in the subscale region was observed on Ni-15Cr and even Ni-10Cr alloys but this layer was never continuous after 30 hr of oxidation. These results indicate that the selective oxidation of chromium in Ni-Cr alloys with chromium contents between 5 to 30 pct may be dependent upon the grain size of the alloy. Fine-grained specimens in this compositional range should have a larger fraction of the surface covered with external Cr2O3 than coarsegrained specimens and the subscale areas required to be sealed via lateral diffusion of chromium should be smaller. It is therefore to be expected that a continuous layer of Cr2O3 can be formed on alloys in this compositional range after short periods of oxidation providing the alloy grain-size is sufficiently small. bo studieS2,3 have established that the oxidation behavior of alloys can be significantly influenced by pretreatments which produce mechanically deformed surfaces. It has been found that deformed surfaces usually promote the selective oxidation of elements in alloys and it is believed that these effects are due to rapid diffusion of elements in the deformed layer. In view of the previous results,' which showed that alloy grain boundaries may play an important role in the selective oxidation of chromium in Ni-Cr alloys, deformed surfaces may promote the selective oxidation of elements in alloys as a result of the numerous grain boundaries formed on the alloy surfaces via recrys-tallization during heating to the oxidation temperature. The purpose of the present studies was to determine the effect of alloy grain size and surface deformation on the selective oxidation of chromium in Ni-Cr alloys at temperatures of 900" and 1100°C in 0.1 atm of oxygen. EXPERIMENTAL The average grain diameter of the alloys used in the previous studies1 was not less than 0.04 mm and alloys with compositions between 5 and 30 pct chromium had average grain diameters between 0.04 and 0.14 mm. Since the oxidation kinetics were already available for these relatively coarse-grained alloys, it was desirable to use these same alloys in the present studies. The surfaces of the alloys listed in Table I of the previous paper were deformed by using a Model F S.S. White Industrial Airbrasive Unit, which delivered a controlled mixture of 25 µ Al2O3 particles in a stream of dry air at high velocity against the surface of a specimen. The amount of surface deformation produced by this treatment was not determined but a re-crystallized layer about 15 µ thick was formed upon annealing deformed specimens. The grain size at the surface of the specimens was reduced to an average grain diameter of 0.01 mm by annealing the deformed specimens, i.e., grit-blasted,

Jan 1, 1970

By Harry K. Ihrig

The hot-working of iron and steel is an art dating back to antiquity, but until about 25 years ago, relatively few alloying elements were used, and these were present only in small percentages. With the exception of sulphur, the amounts of other elements in steels did not markedly affect their hot-workability. The references in the literature on the effect of other elements on the hot-workability of steel are usually reports of failure of these steels in forging or rolling.1-8 With the increased use of alloying elements, and their use in larger amounts, it was observed that many of the new steels were red short in certain critical ranges or at all hot-working temperatures. The stainless steels are particularly difficult to hot-work. The determining of the correct conditions for piercing, rolling and forging of these alloys by experimentation in the mill often results in large losses of these expensive metals. It also is found that the hot-workability limits of many types vary from heat to heat, and hence poor results are obtained on changing to a new heat after a previous one has rolled satisfactorily. To determine the effect on hot-workability of iron to which various elements have been added, it was necessary to devise a method that could be used on small quantities of metal. In such a method, the minimum number of variables should be present, and the procedure should be simple, quick and correlatable with large-scale hot-working operations. Sauveur,9 in the first Henry Marion Howe lecture in 1924, described the effect of carbon on the ductility of steels in torsion near their critical points. He found that carbon increases the plasticity of gamma iron. In the 1930 Campbell Memorial lecture,10 he gives the effect of carbon, chromium, and chromium and nickel on the ductility of steels under 2000°F. in torsion. Ellis11 has studied the malleability of steels at various elevated temperatures by means of a single-blow drop-hammer test. In this test the percentage decrease in height of standard cylinders is taken as a measure of their malleability. He has shown that in the low-alloy steels studied, carbon has a greater effect than nickel, chromium and vanadium. In 1938 the first tests were run on a new quantitative hot-workability test in the laboratories of the Globe Steel Tubes CO. Thum12 mentioned it in 1940. An illustration of the apparatus was published in January 1942.'' The effect of a few alloying elements on the hot-workability of metals was shown in a description of the test in 1944.14 Description of Test Method The method adopted after a trial of several others is a rapid twisting of bars to failure in a furnace. The standard-size bar was chosen as 9/16 in. It is prepared from larger pieces by forging and cold-

Jan 1, 1947

By P. E. Hildebrand, S. W. Mao, C. N. Crain

Hydrologic and economic criteria figure in many obvious ways in water resources development, but they are rarely linked quantitatively, and most of the applications are pertinent only to the case in point. In the preparation of a regional plan for the massive program of groundwater development in the Punjab, situations have arisen where the choice among two or more alternatives was made by analyzing the economic implications of critical hydrologic parameters. Two of these situations which are of more or less general interest are described herein. The first involves basic development policy, i.e., the question of whether groundwater development should be based on the demand of the economy, or the conservation concept of safe yield. The analysis demonstrated that mining of groundwater is clearly indicated for areas where alternative supplies are unavailable. The second problem involves integrating hydrologic data into an economic model to determine optimum well design. From an analysis of all pertinent factors, a simple nomograph was derived for determining well specifications on site during construction. The nomograph can be modified for use in any alluvial terrain. In the Northern Zone of the Indus Plains —the region known as the Punjab- Pakistan is proceeding with integrated development of water and land resources on a scale never before contemplated. The heart of the development plan is a massive program of groundwater development to supplement canal irrigation supplies and to provide drainage relief to the irrigated lands. By the close of 1966 about 2500 high-capacity wells were in operation and furnishing the water supply and drainage requirements for nearly two million irrigated acres. The development plan calls for the construction of a total of nearly 30,000 wells with an aggregate capacity of 120,000 cfs by 1980. This is part of an integrated program eventually affecting over 20 million acres of irrigated lands. [This development program is administered by the West Pakistan Water and Power Development Authority (WAPDA) for which the firm of Tipton and Kalm-bach, Inc. serves as regional planning consultant for the Northern Zone. The material presented herein is derived from planning studies which have been made in connection with the preparation of a regional development plan for the Northern zone.] Pakistan is proceeding with this large-scale development of land and water resources at a time when she is at the threshold of an almost calamitous population growth. Furthermore, she is attempting this development at a time when most of her usable land is already occupied and her food demands exceed current production. Here in the Northern Zone is one of the largest continuous areas of irrigated land in the world, easily irrigated, with a warm, dry climate and ample potential supplies of surface water and groundwater. Except for an abundance of land and labor, other primary resources are lacking or in very limited supply. The agriculture sector so dominates the economy that only by means of an effective development of the agricultural resources can other sectors grow and contribute to a viable economy. Because of inadequate irrigation, farming here has not effectively participated in the twentieth century revolution in agriculture, and only by means of massive development of potential supplies can Pakistan catch up. Capital for any kind of mass development must come from the outside. But the overriding restraint to development of the land and labor resources is the availability of water. ECONOMICS OF DEVELOPMENT The decision-making process in planning regional development becomes increasingly complex as the various sectors of the economy become more highly developed. Where, as in this case, one sector dominates the economy and its development can be considered the key to development of other sectors, the decision-making process is simplified and it is easier to identify alternatives and to trace the prob-

Jan 1, 1970

By Virgil Kirkham

NORTH AMERICA has for many years led the world in phosphate production, but with development of African deposits and their marketing conditions with respect to European countries, this leadership will shortly pass to Africa. Algeria, Egypt, Tunis, and Morocco have large phosphate reserves and a correspondingly large production because of easy mining and a ready European market, which was developed during the war. An increase in home consumption is destined to develop for the eastern American fields, and the countries of the Pacific will provide a market for the western producers. New processes indicate a decrease in fertilizer costs, which will encourage a more widespread domestic use and assure better marketing conditions. The African deposits, although benefited by a water haul, have the disadvantage of being isolated from a source of acid so that the crude rock is shipped from Africa to its destination, whereas in the United States the chief product shipped is acidulated rock or various types of superphosphatic fertilizers. The principal types of phosphate deposits used in the manufacture of fertilizers are guanos, apatite, phosphatic marl, phosphatic limestone, phosphatic shale, and phosphate rock which is also known as phosphorite. Some of these deposits are found on each of the continents; Table 1 gives their occurrence, age, location, character, extent, etc. Most of , the information found in this table represents a compilation of information published elsewhere in a different form and widely scattered.

Jan 1, 1925

By W. D. Forgeng, P. F. Wieser

MnSi alloys containing from 2 to 24 at. pct Si have been investigated by metallographic and X-ray methods. Contrary to published data, the temperature of the ß-manganese to a-manganese transformation is lowered by the addition of silicon. The existence of two additional intermediate phases E and ( is demonstrated. E, ranging in composition from 12 to 15.5 at. pct Si, forms by a peritectoid reaction between ß manganese and the second new phase, (. The latter phase is homogeneous at silicon contents from 16.2 to 18 at. pct and forms peritectically from the 0 phase and liquid. The eutectic reaction occurs between the ( phase and MnsSi rather than the ß phase and Mn3Si. As a result of this investigation, a modification of the manganese-rich section of the MnSi equilihrium diagram is proposed. The binary diagram of Mn-Si, according to Hansen,' Fig. 1, exhibits in the low-silicon region (below 24 at. pct Si) a peritectic transformation at 900°C of 0 manganese + Mn3Si to a manganese as determined by R. Vogel and H. Bedarff2 as well as a thermal effect at 980°C between 16.2 and 22.6 at. pct Si reported by the same authors. The nature of the latter transformation was unknown. K. Amark, B. Boren, and A. westgren3 reported indications that possibly four more phases existed in the range of 10 to 27 at. pct Si. The present investigation deals with the phase relations in the range of 2.1 to 17.7 at. pct Si. A few spot checks were conducted up to 23.84 at. pct Si. EXPERIMENTAL PROCEDURE Small experimental heats were prepared by induction melting in a vacuum furnace using argon as a protective atmosphere. The crucible was of commercial-quality magnesia. The furnace charge consisted of silicon metal and dehydrogenated electrolytic manganese. The typical analysis for these materials is shown in Table I. The molten alloy was tapped into 2-in.-square, 7-in.-long ingots. After visual inspection, a small quantity of alloy in the middle portion of the ingot was separated for use in this investigation.MnSi alloys containing from 2 to 24 at. pct Si have been investigated by metallographic and X-ray methods. Contrary to published data, the temperature of the ß-manganese to a-manganese transformation is lowered by the addition of silicon. The existence of two additional intermediate phases E and ( is demonstrated. E, ranging in composition from 12 to 15.5 at. pct Si, forms by a peritectoid reaction between ß manganese and the second new phase, (. The latter phase is homogeneous at silicon contents from 16.2 to 18 at. pct and forms peritectically from the 0 phase and liquid. The eutectic reaction occurs between the ( phase and MnsSi rather than the ß phase and Mn3Si. As a result of this investigation, a modification of the manganese-rich section of the MnSi equilihrium diagram is proposed. The binary diagram of Mn-Si, according to Hansen,' Fig. 1, exhibits in the low-silicon region (below 24 at. pct Si) a peritectic transformation at 900°C of 0 manganese + Mn3Si to a manganese as determined by R. Vogel and H. Bedarff2 as well as a thermal effect at 980°C between 16.2 and 22.6 at. pct Si reported by the same authors. The nature of the latter transformation was unknown. K. Amark, B. Boren, and A. westgren3 reported indications that possibly four more phases existed in the range of 10 to 27 at. pct Si. The present investigation deals with the phase relations in the range of 2.1 to 17.7 at. pct Si. A few spot checks were conducted up to 23.84 at. pct Si. EXPERIMENTAL PROCEDURE Small experimental heats were prepared by induction melting in a vacuum furnace using argon as a protective atmosphere. The crucible was of commercial-quality magnesia. The furnace charge consisted of silicon metal and dehydrogenated electrolytic manganese. The typical analysis for these materials is shown in Table I. The molten alloy was tapped into 2-in.-square, 7-in.-long ingots. After visual inspection, a small quantity of alloy in the middle portion of the ingot was separated for use in this investigation.

Jan 1, 1964

By R. W. Fountain, W. D. Forgeng

A new constitutional diagram is presented for the cobalt-rich end of the cobalt-titaniurn system. The modifications result from the presence of a new, intermediate, fcc phase, ?, the existence and homogeneity limits of which were established by metallo-graphic and X-ray studies of alloys containing from about 3 to 30 pct Ti. The precipitation of the ? phase from supersaturated solid solution was studied by hardness and electrical resistivity measzsrements, and two distinct stages in the process were observed. COBALT forms the base for a number of precipitation -hardenable alloy systems which may be divided into two distinct categories of practical interest, a) those hardened by intermetallic compounds and b) those hardened by carbide formation. The precipitation of intermetallic compounds from solid solution in cobalt-rich alloys has, however, received very little attention. Although the phase diagrams for some binary systems capable of precipitation have been determined,' there is an almost complete lack of data on the property changes associated with the precipitation, and even less information on the kinetics of the reactions or morphology of the products. More information is available on the precipitation of carbides because of the practical significance in superalloys. A survey of cobalt binary phase diagrams suggested that the cobalt-titanium alloys might provide interesting and useful precipitation-hardenable alloys. The equilibrium diagram as proposed by Wallbaum2 is shown in Fig. 1. Köster and wagner3 have indicated that the maximum solubility of titanium in cobalt is about 10 pct at the eutectic temperature (1135oC), and this decreases to about 7.2 pct at room temperature. The temperature of the allotropic transformation in cobalt is lowered by the addition of titanium, about 5 pct being sufficient to retain the high-temperature fcc modification to room temperature. Wallbaum and Witte 4,5 have indicated that the precipitating phase in alloys containing up to about 29 pct Ti is Co2Ti, a hexagonal Laves phase of the MgNi, type. With slightly higher titanium contents, they also report a cubic modification of Co2Ti of the MgCu2-type Laves phase. Duwez and Taylor6 confirmed the existence of the hexagonal (MgNi2) modification but not the cubic (MgCuz) modification of Co2Ti and suggested that existence of the cubic form may have resulted from impurities in Wallbaum's alloys. In their work on Laves-type phases, Elliott and Rostoker 7 reported the cubic modification of Co,Ti, but did not confirm the existence of the hexagonal modification. However, Dwight8 in a discussion of the work of Eliott and Rostoker again showed the existence of both modifications of Co2Ti, a result which was confirmed at that time by Elliott and Rostoker. As a result of a study on the iron-cobalt-titanium system, Köster and Gellers suggested the existence of a Co3Ti phase isomorphous with Fe3Ti. Witte and Wallbaum,' however, established the fact that no compound, Fe3Ti, exists in the iron-titanium system, and in a later publication, wallbaum2 stated that Kitster and Geller's reasoning was not valid, and no compound, Co3Ti, exists. This conclusion was later acknowledged by Köster.10 Preliminary experiments by the present authors to determine the precipitation-hardening characteristics of the cobalt-rich, cobalt-titanium alloys re-

Jan 1, 1960

By E. P. Polushkin, Henry L. Shuldener

This paper describes the results of microscopic examination of a series of brass pipes removed from apartment and office buildings in New York City, adjacent localities on Long Island, and Philadelphia. They were selected as typical of approximately four hundred pipe specimens obtained over a period of five years during an investigation of corrosion in hot-water installations. A part of the investigation is reported in this paper and includes a brief history of the pipes, a description of their inside surface and microstructure, and a study of the effects of corrosion, with particular reference to the structural aspects of local and selective dezincification. Although the bibliography on the corrosion of brass pipes is quite extensive, it refers almost entirely to corrosion in sea water. The authors believe that their examination of this series of pipes, which had been subjected to the corrosive action of fresh water for various lengths of time, may throw some additional light on the problem of corrosion. Pipes Examined The pipes were made by different manufacturers and their sizes range from 3/4 in. to 4 in. nominal inside diameter, the majority being within I to 2 in. They can be divided into two groups according to chemical composition: (I) with a copper content of 60 to 62 per cent and (2) with a copper content of 65 to 68 per cent. The first group (pipes made of Muntz metal) comprises 22 pipes and the second (pipes made of high brass) comprises 18 pipes. The pipes had been in service in various locations in the hot-water systems of the buildings involved. Some were taken from horizontal lines in the basement, some from overhead distributors and some from vertical risers. The distance, in terms of feet of pipe, of the specimens from the hot-water generator was no less than 75 ft. and often IOO to 300 ft. In the majority of cases the water-heating equipment was provided with a regulator to limit the temperature of the hot water supply. The normal range of temperature in pipe systems of this kind is Ioo° to 160°F. Water Supples The average chemical composition of the water supplies carried by the pipes is shown in Table I. In evaluating the corrosiveness of a natural water, four factors are considered of prime importance: namely, hardness, alkalinity, pH and silica content. The waters listed in Table 1 are characterized by relatively low hardness, 10, alkalinity, low pH and low silica content. The waters of lower pH and higher CO2 content are more corrosive. A characteristic of all of these waters is that they do not deposit a protective mineral coating as do waters with high bicarbonate of lime content, which would be reflected

Jan 1, 1945

By Klaus Schwerdtfeger

The equilibria in the Cr-N system have been investigated in the temperature range 1100° to 1310°C by reacting chromium powder with Nz-Hz gas mixtures. The solubility of nitrogen in chromium in equilibrium with chromium subsitvide ("Cr,N") is given by Chromium subnitride is nonstoichiotnetric; its nitrogen content is always less than that corresponding to the formula CrzN. The lattice paranzeters of quenched samples have been measured; c, and a. parameters are found to increase with increasing nitrogen content. The growth rate of the subnitride layer on chromium plates was measured by a thermogravimetric technique, using a silica spring balance. The self-diffu-sivity obtained from the theoretical analysis of the parabolic rate constant is found to decrease with increasing nitrogen content, i.e., with decreasing vacancy concentration in the nitrogen sublattice. The intrinsic nitrogen diffuivity is derived from another series of rate measurements using "CrzN" plates; the intrinsic diffusivity, DN = 3.2 X 10-a cmZ sec-' at 1200 C, is found to be essentially independent of- the subnitride composition. The concentration gradient was measured in a chromium subnitride layer by the X-ray method and found to be consistent with the derived diffusivity value. TWO chromium nitrides are known to exist:' the nonstoichiometric subnitride "CrzN" and the nitride CrN. In the present work the kinetics of the formation of chromium subnitride from chromium and nitrogen have been investigated at 1100" and 1200°C. In additional experiments the relevant equilibria have been measured. The data are used to evaluate the diffusivity of nitrogen in chromium subnitride. Since chromium nitrides are often found in chromium-containing steels, the results are expected to be helpful in the interpretation of the chemical reactions between chromium steels and nitrogen. Equilibria in the Cr-N system have been determined by several investigators.2"3 The rate of nitriding of chromium was measured by Arkharov et a1 .' in ammonia in the temperature range 800" to 1200°C. The parabolic rate law was observed. Due to the undefined nitrogen activity of the ammonia atmosphere, it is dif- ficult to interpret these rate data theoretically. An additional difficulty arises from the fact that the two-layer scale consisting of CrN and "Cr2N" was formed at the temperatures below 1030°C. The rate of nitriding of technical chromium (95 pct) was measured by Zaks in nitrogen at -1 atm in the temperature range 800" to 1300°C. EXPERIMENTAL METHODS The chromium samples were reacted with Nz-HZ gas mixtures in a vertical tube furnace, wound with Pt-10 pct Rh resistance wire. The gas-tight reaction tube was of high-purity recrystallized alumina. In nitrogen solubility measurements the nitrogen content of chromium was determined by the Kjeldahl method, on samples quenched in the cold part of the furnace. The nonstoichiometry of the subnitride and the nitriding rates were measured thermogravimetrically using a sensitive (+0.1 mg) silica spring balance. For the equilibrium measurements samples of 1 g of chromium powder contained in high-purity alumina crucibles were used. In order to remove most of the oxygen and nitrogen impurities from the chromium, the samples were initially annealed in purified hydrogen until a constant weight was obtained. The chromium plates (approximate dimensions 2 by 1 by 0.08 cm) used for the rate measurements were machined from ingots obtained by arc-melting of iodine-processed chromium. According to manufacturers' specifications the purity of the chromium powder was 99.9 pct Cr and that of the iodine-processed chromium 99.99 pct Cr. Our own spectroscopic analysis of the chromium powder yielded 0.02 pct Fe, 0.05 pct Mn, 0.05 pct Si, and 0.02 pct Ti as major impurities with all the other detectable elements below 0.005 pct. The nitrogen partial pressure of the gas phase was controlled by mixing prepurified hydrogen and nitrogen with constant pressure head capillary flowmeters. Oxygen and water vapor were removed from the mixed gas by passing it through columns of platinized asbestos (450°C) and anhydrone. The gas flowed upward in the furnace with flow rates of 300 to 500 cu cm per min (25"~). Gas tightness of the furnace system was ensured by pressure checks at regular intervals. The furnace temperature was controlled electronically in the usual manner. The reported temperatures were measured with a Pt/Pt-10 pct Rh thermocouple and are estimated to be accurate within ±$C The X-ray measurements were made with a Debye-Scherrer camera and a diffractometer using chromium radiation {\Ka = 2.29092A). EQUILIBRIUM MEASUREMENTS The experimental results of the equilibrium measurements are contained in Tables I to In. Fig. 1 shows the solubility of nitrogen in solid chromium in the temperature range 1100" to 1310°C. In Figs.

Jan 1, 1968

By D. N. Collins, J. R. Stevens

New expressions in the technical assessment of mineral concentration processes have been defined as Concentration Efficiency: Concentration Index: where h is the percentage of head grade; c, percentage of concentrate grade; maximum percentage of concentrate grade obtainable at 100 pct recovery; and R, percentage of recovery. In developing these expressions, the basic requirements for the technical assessment of concentration operations have been defined and the various expressions suggested by others for asses-sing the results of such operations reviewed and criticized. The derived expression for E, depends on a simple combination of recovery (R) and a new term selectivity (s), where S is (c-h)/(c,,, -h), by definition. Limitations of the new expressions are discussed and examples given of applications to concentration operations. It is also shown that the formulae for E, and I, can be applied to scatter diagrams, multi-component systems, size-assay analyses, and classification data. Many methods of quantifying concentrating operations have been proposed. These include direct presentation of weights and assays together with the derived data for other items such as ratio of concentration, recovery, rejection losses, and enrichment ratio. These terms are now accepted mineral dressing nomenclature, and in the assessment of the results of concentration processes, concentrate grade and recovery are together the most widely accepted measures of concentration efficiency. For practical purposes when the concentrate grade is equal to or greater than a predetermined acceptable value, test or operation results may be assessed by the recovery figures alone. Similarly when recovery is within specification, the operation can be assessed by concentrate grade. The ultimate assessment and selection of a concentration operation is—admittedly with a few ex-ceptions—a matter of economics. There is however an intermediate stage in laboratory and pilot plant testing when evaluations must be made without the assistance of an economic yardstick. Numerous techniques are employed to facilitate such evaluations among which may be mentioned graphical plots of grade vs recovery, cumulative weight vs cumulative recovery, scatter diagrams, etc. The desirability of combining metallurgical results and product weights and assays into a single value has been recognized and discussed by many workers1-" with the resultant suggestion and use of such terms as Metallurgical Efficiency ,' Summation Index,' Selectivity Index,'- and Absolute Efficiency B None of these expressions completely satisfies all the requirements of a selectivity or efficiency formula and it is proposed in this report to define the terms, relating to the technical efficiency of a concentrating operation, concentration index and concentration efficiency. Examples are given of their application and a comparison is made of their use in relation to other formulae. All product grades in this paper will be referred to in terms of mineral percentages and a list of symbols is given in Table I. CONSIDERATION OF EXISTING FORMULAE A number of the existing efficiency and index terms used in quantifying concentrating operations are considered below. Metallurgical Efficiency:

Jan 1, 1961

By G. U. Greene

The various lead producers have given the subject of lead drosses much attention in recent years but the problem of their economical treatment is yet to be solved. Formerly the copper in the furnace feed was removed from the furnace in the form of matte. The speiss at that time consisted principally of the iron arsenide. The practice today is to roast off most of the sulphur and the copper in the feed forms a dross in the furnace, which is removed from the furnace with the lead. This material is poured into the drossing kettles and allowed to cool down to but slightly above the freezing point of lead. The copper dross, containing almost all of the arsenic and part of the antimony, is skimmed off and treated in a small reverberatory furnace at most plants. This is essentially a liquation process. The skimmed dross contains from 70 to 80 per cent lead, and much of this lead is liquated out. The products from this treatment are: (1) impure lead, (2) speiss and (3) matte. The speiss from the reverberatory furnace was studied in this research. The literature on the subject is of very little assistance, as almost no work has been done on the problem of establishing the exact identity of the various phases present. One author(1)† states that speiss consists of a series of isomorphous compounds of the general formula FexAsy in which the Fe may be replaced by Ni, Co, Cu, Pb, Ag, Au, Pt, Zn, Cd and the As replaced by Sb, S and Bi. Hofman(2) states that the iron arsenide present is Fe5As. Experimental Work In the present research, the author used for methods in an attempt to determine the composition of the various phases: (1) chemical, (2) microscopic, (3) roentgenographic and (4) thermal. Previous to this research, considerable time had been spent making analyses of different speisses, but unfortunately no very definite conclusions could be made as a result of these analyses.

Jan 1, 1937

By M. Khorouzan, L. Thomas

Designers of semiconductor devices have been strivi,ng to resolve problems associated with Au-A1 alloys in bonded in.tercomzeclions. One approach now being- used is that of waintaining a physical seyav-atioz between the two metals in bond areas. This is accolrzplished by alunzincnz-plating a bonding area on the tips oJ the kovar leads and using alcminurn wires to join the senzicondictor device to the leads. The portion of the kovar lead which is on the externul side of the sealed package is gold-plated to provide an oxide-free surface for soldering or welding. A discoloration condition originally thought to be sinilar to purple plague, occuving in the yluled uluninur bonding area after package sealing, has been investigated to determine its efiects ipm bond integrity. Electron-micro-probe analysis determined that no1 only gold, but lead, zinc, and silicon were also present in the discolored area. A series of samples conlaining' conkrolled umonts of these inzpitrities weve prepared and subjected to a sil.zuluted sealing process. The investigations swcued that, of the contawiinants, only zinc toas detrinenlul to Lhe bond integily. The discoloration condition itself was found not to be detrimental to the bond integrity. DESIGNERS of semiconductor devices have been striving to resolve problems associated with Au-A1 alloys in bonded interconnections. One approach now being used is that of maintaining a physical separation between the two metals in bond areas. This is accomplished by aluminum plating a bonding area on the tips of the kovar leads and using aluminum wires to join the semiconductor device to the kovar leads. The portion of the kovar lead which is on the external side of the sealed package is gold-plated to provide an oxide-free surface for soldering or welding. Contamination as evidenced by discoloration of the aluminum-plated area was observed in a number of integrated circuits undergoing examination for defect characteristics which cause electrical failures.' This paper contains the results of an investigation to determine the nature of this discoloration, its cause, and its effect upon the integrity of the interconnection bond. I) THE NATURE AND EXTENT OF ALUMINUM-BOND CONTAMINATION The initial hypothesis in the investigation was that the discoloration was caused by reaction of the aluminum film with some unknown contaminants during the sealing of the hermetically sealed integrated-circuit flat package. The package is a rectangular ceramic container sealed with glass which surrounds the kovar leads as well as joining the top to the bottom. The seal is made hermetic by heating and cooling the package to devitrify the glass. In the case of the packages under investigation, the hermetic sealing had been accomplished with dry air as internal atmosphere. The apparent effect of contaminations as observed by microscopic examination was the formation of surface oxides having variations in color encompassing the whole spectrum of visible light. The contamination appeared to be related to one of the more notorious examples of these colorations, the so called purple plague.' In addition to purple plague, Fig. 1 shows the tarnish in the luster of the aluminized surface in the bond area which had been observed in many of the integrated circuits. To identify the contaminant in the bond area electron-probe microanalysis techniques were used.3 Fig. 2 shows the result of this analysis. The contaminants identified were gold, aluminum, zinc, lead, silicon, and cobalt. Fig. 2(a) is a back-scatter display of the area under study. The back-scattered electrons provide a general indication of the distribution of elements in the specimen surface. Elements with higher atomic number scatter more electrons back from the surface and are seen as light areas in the picture. The sample current, Fig. 2(b), is the amount of current conducted by the specimen as a result of electron-beam striking it and is an indication of element distribution. The Sample current is the reverse of back-scatter and complements it. Other pictures in Fig. 2 are produced by characteristic X-rays generated by the elements, allowing the isolation of the element of interest. The isolated element appears white and all other elements are dark. In this manner a comparative study provides a correlation between different surface areas and the elements which are in these areas. The area covered by the gold film, Fig. 2(c), shows that the boundary between the gold film and the kovar is not sharp as expected and that some sort of diffusion has taken place. Fig. 2(c) shows that some gold particles have been carried to the bond area and are in the proximity of the bonded wire in spite of the presence of a physical barrier in the form of the un-

Jan 1, 1967

By B. H. Kear, S. M. Copley

Stress-stvain curves are presented for Ni3Al (y') cvystals in several ovientations, deformed in tension and compression at constant displacement rate, at temperatures from 70° to 2000°F. Both the yield stress and wovk havdening increase with temperature, with the magnilude of the effect dependent on ovientation. The yield stress maximum occurs at 1500°F in [001], at 1400°F in [011], and at 1200°F in [111]. The suppression of the yield stress peak in [011] and [111] orientatiorzs is due to the onset of cube slip, rather than octahedval slip, a1 elerated temperatures. The temperature and orientalion dependence of work hardening in nominal single slip orientations corvelates with changes in the CRSS ratio for octahedral slip and cube slip, in agreement with a model for work hardening based on pinning of screw dislocalions by cross slip from an octahedral plane into a cube plane. It is concluded that the unique plastic properties of y' have a decisive influence on both ductility and strength characleristics of y +y' nickel-base superalloys. It has long been recognized that the strength of y + y' nickel-base superalloys depends on the precipitation of the y' phase [basically Ni3(Al,Ti)]. This paper presents new data on the strength characteristics of single crystals of simple y' (Ni3Al), and forms the first step in a systematic program aimed at elucidating the mechanisms of hardening in the complex commercial alloys. 1) EXPERIMENTAL PROCEDURE Single crystals of off-stoichiometric NiA1 were grown from the melt under vacuum by a modified Bridgman method. The melt was poured into a preheated alumina mold and crystal growth was promoted from one end by gradient cooling. The crystals were homogenized by annealing in hydrogen at 2400° F for 72 hr followed by furnace cooling. Chemical analysis of samples taken from several crystals gave an average composition of 88.2 wt pct Ni. Spectrographic analysis gave as the principal impurities in weight percent— Si (0.02), Mg (0.01), Fe (0.02), Ti (0.002), Cu (0.008), and Co (0.03). Tensile specimens with specifications as in Fig. 1 were prepared by a series of operations involving electrical discharge machining, precision grinding, and electropolishing. Compression specimens with dimensions 1/4 by 1/4 by -3/4 in. were prepared in a similar manner, except for the initial shaping operation using a precision cut-off wheel/two-circle goniometer unit to give selected crystal orientations. Specimens were deformed in a Baldwin-Wiedemann testing machine with furnace attachment, using a strain rate of 5 x 10-4 sec-1. The strain measuring device consisted of extension arms attached to the tensile grips (or compression plattens) at one end and leading out of the furnace to an LVDT at the other. Temperature was controlled by a thermocouple placed in contact with the specimen. According to the known phase diagram for the Ni/A1 system,' when an alloy of the specified composition is cooled from the melt, primary y (nickel solid solution) dendrites grow at the expense of the liquid phase, which becomes enriched in aluminum. At the eutectic composition the remaining liquid freezes as a two-phase mixture of y + y' (Ni3Al). Upon further cooling, a solid state transformation occurs, involving the precipitation of y' in the primary dendrites, and the complete transformation of the eutectic mixture to massive y'. The as-cast structure consists, therefore, of y + y' dendrites with interdendritic regions of massive y', i.e., transformed eutectic, Fig. 2. 2) DISCUSSION OF RESULTS 2.1) Stress-Strain Curves. Fig. 3 shows tensile stress-strain curves for crystals in orientations close to [001] deformed at temperatures from 70° to 2000°F. Both the yield stress and total elongation are strongly temperature-dependent. At 70°F, easy glide is absent, and the work hardening coefficient BIT - G/300. At T > 1500°F, the negative slope of the stress-strain curves is due to pronounced necking in the crystals. The yield stress maximum at 1500° F corresponds with a minimum in the ductility, Fig. 4. The extensive duc-

Jan 1, 1968

By M. Sheffield

This paper presents a technique lor predicting the flow of oil, gas and water through a petroleum reservoir. Gravitational, viscous arid capillary lorces are considered, and all fluids are considered to be slightly compressible. Some theoretical work concerning the fluid flow in one-, two- and three-space dimensions is given along with example performance predictions in one- and two-space dimensions. INTRODUCTION Since the introduction of high speed computing equipment, one of the goals of reservoir engineering research has been to develop more accurate methods of describing fluid movement through underground reservoirs. Various mathematical methods have been developed or used by reservoir engineers to predict reservoir performance, 193-5,7,8 The work reported in this paper extends previously published work on three-phase fluid flow (1) by including a rigorous treatment of capillary forces and (2) by showing certain theoretical mathematical results proving that these equations can be approximated by certain numerical techniques and that a unique solution exists. DISCUSSION The method of predicting three-phase compressible fluid flow. in a reservoir can be summarized briefly by the following steps. 1. The reservoir, or a section of a reservoir, is characterized by a series of mesh points with varying rock and fluid properties simulated at each mesh point. 2. Three partial differential equations are written to describe the movement at any point in the reservoir of each of the three compressible fluids. All forces influencing movement are considered in the equations. 3. At each mesh point, the partial differential equations are replaced by a system of analogous difference equations. 4. A numerical technique is used to solve the resulting system of difference equations. Capillary forces have been included in two-phase flow calculations.1,4,8 The literature, however, does not contain examples of prediction techniques for three-phase flow that include capillary forces. Where capillary forces are considered, each of the three partial differential equations previously discussed has a different dependent variable, namely pressure in one of the three fluid phases. Therefore, three difference equations must be solved at each point in the reservoir. Where large systems of equations must be solved simultaneously, an engineer might question whether a unique solution to this system of equations actually exists and, if so, what numerical techniques may be used to obtain a good approximation to the solution. It is shown in the Appendix that a unique solution to the three-phase flow problem, as formulated, always exists. It is also shown that several methods may be used to obtain a good approximation to the solution. The partial differential equations and differenceequations used are shown in the Appendix. Matrix notation has been used in developing the mathematical results. Two sample problems were solved on a CDC 1604. They illustrate the type of problems that can be solved using a three-phase prediction technique. SAMPLE ONE-DIMENSIONAL RESERVOIR PERFORMANCE PREDICTION A hypothetical reservoir was studied to provide an example of a one-dimensional problem that can be solved. Of the several techniques available, the direct method of solution as shown in the Appendix was used. The reservoir section studied was a truncated, wedge-shaped section, 2,400 ft long, with a 6' dip. (A schematic is shown in Fig. 1.) This section was represented by 49 mesh points, uniformly spaced at 50-ft intervals. The upper end of the wedge was 2 ft wide, and the lower end was 6 ft wide. The section

Jan 1, 1970

By A. E. Nehrenberg

THE mechanism by which austenite forms in steels has received a great deal of attention in the literature in past years.'-'* Our present knowledge concerning this mechanism has been recently summarized quite concisely by Bain and Vilella,1 while a few years ago the literature was carefully reviewed by Roberts and Mehl.² The consensus is that any ferrite-carbide interface is a potential site for the nucleation of austenite during heating above the Acl temperature, and that the new austenite generally grows freely to produce approximately equiaxed grains, whether the carbides are initially present in the lamellar or the spheroidal form. In the case of eutectoid steels, growth of the new grains of austenite continues until contact is established with other grains. Then growth stops and an initial austenite grain size is established which does not change until the heating is continued to some high temperature at which grain coarsening begins. In the case of pearlitic steels which are not of eutectoid composition, the proeutectoid ferrite or carbide may interfere with the growth of the austenite if the temperature is not above that designated the A63 or the Acm, respectively. Although a large amount of work has been done to establish the mechanism of austenite formation in steels, it became clear to the present author while he was studying the transformation characteristics of a new 0.25 C Mn-Si-Ni-Mo hypoeutectoid steel" that the manner in which austenite grows in steels depends upon some factor, or factors, not previously considered. This was indicated by the fact that when this steel in the spheroidized condition was heated above the Ae1 temperature the new austenite which was formed did not envelop the carbides and grow in an equiaxed manner as described by Bain³ or spheroidized steels. Instead, in this steel, the austenite was observed to grow much more readily in certain directions than in others with the result that at temperatures within the Ac1-Ac³ ransformation range the austenite grains were acicular in shape. The excess ferrite was also found to be acicular with the distribution of these phases being such that a lamellar pattern was developed. This unusual directional growth of austenite in this new steel initially in the spheroidized condition is illustrated by fig. 1. A search of the literature revealed that this type of growth was not necessarily peculiar to this steel for similar microstructures had been observed by other investigators.4-8 However, the full significance of these microstructures does not appear to have been appreciated, and no work has been done to determine the conditions responsible for this directional growth of austenite or to arrive at an understanding of it. It was for this purpose that the work described in the present paper was carried out. Material: During the course of this investigation a total of 15 steels was studied. They consisted of hypoeutectoid, eutectoid and hypereutectoid carbon steels, and hypoeutectoid and hypereutectoid alloy steels, all of which were obtained in the annealed condition from commercial warehouse stock. As received, the carbon and alloy hypereutectoid steels had microstructures which consisted of spheroidal carbides in ferrite, whereas the eutectoid steel and the hypoeutectoid steels were pearlitic. The grades of steel represented were 1050, 1080, 10110, 3310, 4140, 4340, 4615, 6145, 8620, 9260, 9442,

Jan 1, 1951

By W. B. Agocs

IN August 1954 a low altitude test geophysical survey was made in the Green Pond area of Morris County, New Jersey, with a Gulf Research and Development Co. Model II total magnetic field variation magnetometer mounted in a Sikorsky S-55 helicopter. The test was made in this area to compare the results of a high precision, very low altitude magnetometer survey with an existing ground magnetic survey in this area having known magnetite concentrations, so that the method could be used in areas of difficult access for the detailing of airborne magnetometer anomalies of interest in place of ground surveys. The load capacity of the Sikorsky S-55 permitted installation of a recording scintillation counter so that a radioactivity survey would be made simultaneously with the magnetometer survey. The area surveyed is located at approximately 41°00'N and 74o28'W, just south and east of the town of Green Pond, N. J. The outstanding topographic feature of the region is Copperas Mountain, a well defined ridge, maximum elevation 1222 ft, which runs the entire length of the survey. The lowest point in the survey, 810 ft, is in the extreme eastern corner. Topography of the area is shown in Fig. 1. The three major rock units outcropping in the area are all metamorphic: the Pochuck gneiss, which has been divided into two metamorphic facies; the Byram gneiss; and the Green Pond conglomerate. The relative ages of the Pochuck and Byram formations, both pre-Cambrian, are in doubt, but it is believed that the Pochuck is the older of the two.' The Green Pond conglomerate is Silurian.' Distribution of the outcrops and mine locations is shown in Fig. 1. Two facies of the Pochuck gneiss can be distinguished locally—the Copperas Mountain and Kitchell members. The Copperas Mountain member is a hornblende gneiss, and all the mines and prospects in the area are in this unit. The Kitchell is a quartz-plagioclase feldspar gneiss. The Byram gneiss is a relatively nonresistant valley formation which is high in the potash feldspar. The Green Pond conglomerate is a well indurated quartzite-conglomerate which forms the Copperas Mountain and the Green Pond Mountain's ridge to the north. It overlies the gneisses with a strong angular discordance that may be a fault. The geologic structure of the Green Pond area is relatively uncomplicated. The foliation planes of the gneisses dip steeply to the southeast, and the Green Pond conglomerate dips steeply to the northwest. Additional faulting in the area is indicated at the contact between the Kitchell member of the Pochuck and the Byram along the base of the topographic spur extending to the southeast from Copperas Mountain. The magnetite mines of Pardee, Winter, Davenport, Green Pond, Copperas, and the Bancroft shaft are described by Bayleyl and Stampe2.' The ore is in the Copperas Mountain member of the Pochuck gneiss. The magnetite veins are 10 to 50 ft wide and up to 300 ft long, dipping to the southeast at angles ranging from 40" to 75". The locations of these mines are shown in Fig. 1. Dip Needle Survey: The dip needle survey shown in Fig. 2 was taken from a U. S. Bureau of Mines Report of Investigations." The figure numbers below the local, individual map area outlines refer to the figures in the aforementioned reports which were not contoured. The area of the dip needle survey was confined almost exclusively to the outcrops of the Pochuck gneiss. The separation between survey profiles was 100 ft and the distance between stations on the profiles was 25 ft in highly anomalous zones to 100 ft in magnetically flat areas. A total of 16 1/2 miles of traverse was surveyed over an area of approximately 1/2 sq mile with 2050 stations. The magnitude of the magnetic anomalies is difficult to determine due to the lack of information concerning the type of dip needle used and the procedure followed in making the dip needle survey. This latter would include the method of "zeroing" the dip needle and the procedure of reading at the stations, whether on the swing or statically. Calibrations made of the Gurley dip needle, Lake Superior type, show a static sensitivity of 385 gamma per degree in the range from —25" to +35o, corresponding to a variation in the total field of —9600 gamma to +13500 gamma in a total field of 57000 gamma, inclination 72". The sensitivity increases to 16 gamma per degree from a deflection of 60" to 76", and from 76" to 172" the sensitivity decreases continuously to a low of 260 gamma per degree. From the above it may be seen that it is difficult to assign an arbitrary sensitivity for the dip needle used on this survey. However, an estimated value of 100 gamma per degree may be assigned. On this basis, the majority of the magnetic anomalies, whose deviation is +20°, would be 2000 gamma. Locally, west and northwest of the Pardee mine the magnetic anomaly is +50°, or 5000 gamma; in the Green Pond mine area deviations of +75" are observed that would correspond to anomalies of 7500 gamma. The areal extent and width of the dip needle magnetic anomalies is comparable to profile and station spacing. Hence it is concluded that part of the detail may be due to control, and the probable cause of the magnetic anomalies is at or near surface exposures of magnetite concentrations in the form of veinlets and disseminations whose locations correspond to the local magnetic anomalies. On the basis of the magnetics, none of the magnetite concentra-

Jan 1, 1956