Search Documents

By T. C. Boberg, R. B. Lantz

This paper presents a method for calculating the producing rate of a well as a function of time following steam stimulation. The calculations have proved valuable in both selecting wells for stimulation and in determining optimum treatment sizes. The heat transfer model accounts for cooling of the oil sand by both vertical and radial conduction. Heat losses for any number of productive sands separated by unproductive rock are calculated for the injection. shut-in and production phases of the cycle. The oil rate increase caused by viscosity reduction due to heating is calculated by steady-state radial flow equations. The response of successive cycles of steam injection can also be calculated with this method. Excellent agreement is shown between calculated and actual field results. Also included are the results of several reservoir and process variable studies. The method is best suited for wells producing from a multiplicity of thin sands where the bulk of the stimulated production comes from the unheated reservoir. The flow equations used neglect gravity drainage and saturation changes within the heated region. INTRODUCTION This paper presents a calculation method which can be used to predict the field performance of the cyclic steam stimulation process. The calculation method enables the engineer to select reservoirs that have favorable characteristics for steam stimulation and permits him to determine how much steam must be injected to achieve favorable stimulation. While the calculation represents a considerable simplification of physical reality and the results are subject to numerous assumptions which must be made about the reservoir, it has been found that realistic calculations can be made of individual well performance following steam injection. The duration of the stimulation effect will depend primarily on the rate at which the heated oil sand cools which, in turn, is determined by the rate at which energy is removed from the formation with the produced fluids and conducted from the heated oil sand to unproductive rock. A complete mathematical solution to this problem is a formidable task, and finite difference techniques would undoubtedly have to be used. The calculation method pre- sented here utilizes analytic solutions of simple related heat transfer and fluid flow problems. The method is sufficiently simplified that it can be used as a hand calculation, although the calculations are somewhat lengthy and laborious. For that reason, the analysis was programmed for an IBM 7044 digital computer. Well responses observed at the Quiriquire field in eastern Venezuela&apos; have been matched using this program after making suitable approximations for reservoir and wellbore conditions. One of the most valuable uses of this calculation method is to assess the effect of reservoir and proc-cess variables on the stimulation response. This paper contains results of several studies made of key reservoir and process parameters. Among the most important of these is the influence of prior wellbore permeability damage. If a well is severely damaged prior to stimulation, a higher stimulation response will be observed than if it is undamaged. If a portion of this damage is removed, a permanent rate improvement will occur. THEORY I)ES(:KJJ&apos;TION OF CALCULATION METHOD The process of cyclic steam stimulation is essentially one of reducing oil viscosity around the wellbore by heating for a limited distance out into the formation through the injection of steam. Suitable modifications of the calculation technique presented here can be made so that stimulation of wells by hot gas injection or in situ combustion can also be calculated. A schematic drawing of the heat transfer and fluid flow considerations included in the calculation method is shown in Fig. 1. In brief, the calculation assumes that the oil sand is uniformly and radially invaded by injected steam. For wells producing from several sands, each sand is assumed to be invaded to the same distance radially. In calculating the radius heated rn energy losses from the wellbore and conduction to impermeable rock adjacent to the producing sands are taken into account. After steam injection is stopped, heat conduction continues and oil sands with r < ra cool as previously unheated shale and oil sand at r > r, begin to warm. The effect of warming of oil sand out beyond r, has little effect on the oil production rate compared to the effect of cooling of the oil sand nearer the wellbore than ra. Thus, in computing the oil production rate, an idealized step function temperature distribution in the reservoir is assumed where the original temperature exists for r > rn and where an average elevated temperature exists for r < rn. The average temperature in the oil sand for the region r < rn is computed as a function of

Jan 1, 1967

By G. F. Loughlin

THE matter of grading Indiana oolitic limestone has been under a cooperative study by the Supervising Architect&apos;s office, the U. S. Geological Survey, the Bureau of Standards, and the former Indiana Limestone Quarrymen&apos;s Association. As the criteria for grading are necessarily based on a number of geologic and related factors of which those quarrying and using the stone had only imperfect appreciation, the first part of the report is a very elementary account of the origin, structure, and the chemical and physical properties of tie stone, and their relations to durability and utilization, and serves as a foundation for the second part, which discusses grading and pro- poses limits for grades established by the quamymen. Salient features of Part I of a report that has been prepared are the variations in uniformity of stone due to cross bedding, and local uncomformities; the relative prominence of weathering effects on the coarser uneven grained surfaces, and its apparent absence on fine, uniform grained surfaces, although the amount of weathering is the same on each; the attributing "crow feet" (stylolites) to solution under pressure, and the explanation that, whereas the thinnest "crow feet" have no noteworthy effect on weathering quality or strength, the thicker ones are likely to weather out rapidly and to promote splitting; the influence of fracturing on the oxidation of the original gray or "blue" to buff color above the ground water level; the interpretation of chemical analyses and the pointing out that both the gray and buff colors are due mainly to organic

Jan 1, 1929

Jan 1, 1887

By AIME AIME

The following changes of address of members have been received at the Secretary&apos;s office during the period of March 15 to May 1, 1907. This list, together with the list of changes of address published in Bi-Monthly Bulletin, No. 14, March, 1907, supplements the annual list of members corrected to Jan. 1, 1907, and brings it up to the date of May 1, 1907. The names of members who have accepted election during March and April, 1907 (new members), are printed in italics. The large number of changes of address since Jan. 1, 1907; shows the importance of publishing these changes as frequently as possible, and the Bi-Monthly Bulletin has. been selected as the means to present this information to the members of the Institute. By the simple method of cutting out these names and addresses and pasting them directly over the corresponding names in the annual list of members, the record can be kept practically up to date, and the value of the list correspondingly increased. For this purpose the changes of address have been printed only on one side of the page. The names of new members, being in italics, are readily distinguished from the others, and can be pasted in approximate alphabetical order on the margins of the pages.

May 1, 1907

By R. W. Raymond

(Pittsburg Meeting, March,1910.) THE Giroux Consolidated Mines Co. is equipping a five-compartment shaft at Kimberly, Nev., which will serve the Alpha mice. The depth of this shaft, January, 1910, is 963 ft., and of this depth 948 ft. was opened by raising, 15 ft. of sinking was done so that the bearers, collar-set, and three shaft-sets might be installed and concreted, and with this done it was possible to erect the necessary surface-equipment for resuming shaft-timbering on the completion of the raise. The arrangement of the shaft-timbering is shown in Fig. 1. At the 1,000-ft. level of the Alpha, and 750 ft. SW. from the Alpha shaft, a 14- by 18-ft. station was cut, and a 25-h-p. air-hoist *as installed. From here the raising commenced on July 5, 1909. The raise was cut approximately 13 by 21. ft. in area, and supported by timbering with square sets, illustrated in Fig. 2, which shows the division into four compartments. The end compartments, which were used as chutes, had the center girts heavier than in the others on account of the wear from falling rock. The chute-lining was braced by inserting 8- by 8-in. stiffeners parallel to and half way between successive caps. Similarly, the lagging on the wall sides of the cage-way and the compartment for pipes and ladder was stiffened with 4- by 6-in. timbers. In the pipe-and-ladder compartment the chute-stiffeners were reinforced with 8- by 8-in, struts, and as the cage-way was partitioned off by braced lining, there was practically no chance of rock entering the ladder-way in case a chute burst into the cage-way. Over the two center compartments the last two, sets were always bulkheaded with 8- by 12-in. timbers, shown in Fig. 3, and from the lower bulkhead the cage sheave-wheel was suspended. After a round of holes had been blasted and the loose

Jun 1, 1910

By Walter Crooke

Regenerative hot-blast stoves are now in general use in all parts of the world, and are so well understood and appreciated, that I need not take up your time with an account of their history and introduction into the United States. My object in writing this paper is to give you a short description of a stove that is now being very favorably received and adopted here (see drawing). The stove was first introduced into this country in 1887 by M&apos;Clure & Shuler (now M&apos;Clure & Amsler), who have the management of the patent right in the United States. The English design had to be modified to suit the exigencies of American blast-furnace practice, which, in many respects, widely differs from our English experience. In the first place, the fire-bricks used in America expand to an extent unknown in England, and it became necessary to make special provision for this by increasing the number of cross-walls, and by leaving a space at the top of the stove through which the lining could expand. The expansion laterally was, however, more difficult to provide for, as the combustion-chamber in the center, being the hottest part of the stove, must necessarily expand more than the outer walls, and therefore tend to squeeze up the flue-openings. On first introducing these stoves to American ironmasters, a feel ing seemed to prevail that a " four-pass " stove did not utilize the whole of its surface. They also had an idea that the " two-pass " stove let the burning gas go before all the duty had been extracted from it; so that it was found neceseary to design a stove of a special character to suit their wishes. Hence the "three-pass" chimney top stove now before your notice, the advantage claimed for which is that each stove is independent, requiring no underground chimney flue or stack, and can be erected at a very light cost. The working of these stoves has proved to be very successful wherever they have been introduced.

Jan 1, 1891

By Valentin R. Garfias

The world&apos;s production of petroleum during 1926 is estimated at 1,096,000,000 bbl., an increase of about 29,000,000 from that of 1925 and somewhat larger than the average during the last 4 years, which is about 1,049,000,000 bbl. The daily average during the year may be estimated at 3,000,000 bbl. of which the United States produced 2,123,000 and other countries 877,000. The outstanding developments during the year have been the decline of the Mexican fields, the counterbalancing of this decline by the increase in Venezuelan and Russian production, and increases in Roumania and Colombia. During 1926 the United States, Mexico and Russia retained their relative positions as the three leading producers, while Venezuela probably outranked Persia for fourth place, Roumania passed Dutch East Indies for sixth, and Colombia moved from sixteenth to the eleventh position. It further appears that should present conditions develop normally throughout 1927, it is not improbable that Mexico will be outranked by Russia as the second oil-producing country and that the increased yield of Colombia will place this country in the eighth or ninth position, and ahead of India. The United States and Mexico should produce in 1926 about 79 per cent. of the world&apos;s total and the aggregate of the seven leading countries should be close to 95 per cent. of the total. It is interesting to note that about 85 per cent. of the total comes from fields on the American continent, the United States accounting for about 71 per cent., and Spanish-American countries and Trinidad for 13 per cent. Production of countries other than the United States and Mexico has gradually increased during the last four years and now represents about 21 per cent. of the total. The United States easily retains its long standing leadership with a total yield of 775,000,000 bbl., or an average daily yield of 2,123,000, representing about 71 per cent. of the total, which is about equal to that of the previous year. An increase in production of about 11,000,000 bbl. is indicated by the statistics so far available. It will be noted that the American production in the last 4 years has averaged about 746,000,000 bbl. yearly and that this uniformity, as well as the marked increases

Jan 1, 1927

LIST OF MEMBERS, ASSOCIATES AND JUNIOR ASSOCIATES ALPHABETICALLY ARRANGED ||Abad, Leopoldo F, College of Min, Univ of California Berkeley, Cal &apos;23 ||Abarquez, Ramon F, Met, Bureau of Seience Manila, P I &apos;24 ||Abbey, Robert Graham, Student, Case School of Applied Science Cleveland, Ohio &apos;21 Abbort, A N , Mines Supt , Mazapil Copper Co , Ltd Concepcion del Oro, Zacatecas, Mexieo &apos;23 Abbott, Clarence E , Gen&apos;l Supt , Iron Mines Div , Tenn Coal, Iron & R R Co , 1405 Minnesota Ave , Bessemer, Ala &apos;04 Abbott, Louis Benjamin, Chief Engr, Consolidation Coal Co, Elkhorn Div Jenkins, Ky &apos;15 Abbott, Robert R , Met Engr , Peerless Motor Car Co Cleveland, Ohio &apos;12 ||Abbott, Wells Osborn, Ray Consolidated Copper Co Hayden, Ariz &apos;23 Abeel, George H, Jr, Cons Min Engr 4812 W 17th St, Los Angeles, Cal &apos;18 Abel, Albert E, Asst to Pres, Valley Mould & Iron Corpn Sharpsville, Pa &apos;19 Abeloff, Miran S Address Wanted &apos;21 Abernathy, G E, Kansas State Teachers College Pittsburg, Kans &apos;20 Abey, Hiroshi, Min & Met Engr. Takata & Co, 2 Yeirakucho, Niehome, Kolimachi-ku, Tokyo, Japan &apos;17 ||Aborn, Robert H 24 Groveland St, Auburndale, Mass &apos;19 Abouchar, Sylvain Sley, Min Engr & Geol , Care of S H Sekaly, 13 Rue El Nimr, Cario, Egypt &apos;17 Abraham, Arthur W 1828 N Alexandria Ave, Los Angeles, Cal &apos;20 Abrahams, A. I 115 East 82nd St. New York, N Y &apos;14 ||Abrahamson, C. Walter, Min Engr, Brule Min Co Stambaugh, Mich &apos;21 Abrams, Charles Jackson Columbia Bldg, Spokane, Wash &apos;21 Abrams, David H, Min Engr, S E Dickey & Co, 809-11 Johnstown Trust Bldg, Johnstown, Pa &apos;20 Acker, E 01C, Met 128 East Washington Lane, Germantown, Philadelphia, Pa &apos;86 Acker, William L, Diamond Drill Contractor Mears Bldg, Scranton, Pa &apos;18 Ackerman, Ernest R, Pres Lawrenee Portland Cement Co Plainfield, Union Co, N J &apos;15 Adachi, Jinzoo 11 Shiba Park, Shiba-Ku, Tokyo, Japan &apos;88 Adachi, Yuich, Meeh Engr, Anzan Steel Works, Anzan, South Manchuria, China, (Via Dairen) &apos;21

Jan 1, 1923

By Don Rose

In the USA the cost of steel ribs for tunnels approximates $100 million each year. European practice has long since abandoned heavy steel ribs for tunnel support, and tunnel coats in Europe (normalized for wages) are about half the costs incurred in the USA. A feeling has existed for some time that the USA practices of supporting tunnels with heavy steel ribs have been overly conservative. The USA practice is based on rock load coefficients by Karl Terzaghi. In 1946, Karl Terzaghi published a tunnel rock classification system (Terzaghi, 1946), with the rock loads on tunnels predicted for each class of rock. No data on real rock loads were presented by Terzaghi and his rock load coefficients may have been largely intuitive. His classification system and associated predicted rock loads have been widely used in the USA. Each rock class, taken from Terzaghi&apos;s classification system, is assumed to generate loads of loosened rock resting as dead load. The dimensions of the loosened rock are described by rock load coefficients multiplied by the tunnel diameter. The resulting rock loads are used by design engineers, contractors and agencies to size supporting steel ribs. Terzaghi clearly stated that he had conservatively assumed high rock loads for his classes 4, 5 and 6 to take a presumed effect of groundwater into account. If the tunnel was not affected by ground- water, Terzaghi stated those rock loads should be reduced by 50 percent. Twenty two years later Tor Brekke (1968) wrote a paper clearly showing that based on observation of more than 250 tunnels groundwater does not affect tunnel rock loads. In 1969, Deere, et al., published measurements made on a number of tunnels, and a well-known curve was drawn by Deere to illustrate Terzaghios coefficients graphically. Deere&apos;s text stated that Terzaghi&apos;s predicted rock loads were too high and should be reduced. Cording and Deere (1972) more recently published data indicating that very large real rock caverns and chambers were being successfully built using rock bolts, which can take only a very limited rock load, thus indicating that real rock load is much smaller than Terzaghi or even Deere predicted.

Jan 1, 1982

By P. BOURY

THIS account of a contrivance which has been found serviceable in practice may be of interest to engineers, and&apos; especially to those engaged in hydraulic mining. In that process, one feature which seems at first sight to possess little significance, is highly important in its effects, namely, the regular supply of water to the " giants." The chief condition of this regularity is an even flow in the pipe-line from the penstock to the nozzle. This, of course, requires that the penstock be kept full. Any considerable surplus of water, overflowing at the penstock, is a simple waste, unless it be otherwise utilized in the sluices. At all events, it does not affect the delivery of the nozzles. But a deficiency at the penstock may admit air into the pipe; and this may produce hydraulic recoil, injuring the line by incessant vibrations, giving rise to leaks, and even to blow-outs, and (when a partial vacuum exists at the time of the fracture the collapse of the pipe. An accident of this sort in our main pipe-line, occasioned partly by a settling of the ground and partly by the presence of air in the pipe, led to the employment of the device here described. The line referred to is made of 30-in. pipe, successively reduced to 18 and 15 in. in diameter, for the supply of two giants. By reason of the causes above mentioned, the 30-in. pipe burst more than 1,400 ft. from the penstock, and, despite the air-valve, the 30-in. pipe was collapsed to such a degree that one length of it, next to the penstock, was squeezed together and positively swallowed by the main pipe, through which it traveled for 750 ft., piercing through a short elbow on the way. This remarkable result was undoubtedly the effect of the vacuum suddenly produced when the pipe burst.

Sep 1, 1906

By FREDERICK W. BRADLEY

MINING is one of the world&apos;s oldest industries and has pioneered the civilization of all new lands. Today, mining is not only one of the essential and basic industries of the world, but it is constantly growing in magnitude and becoming more important. We think that the most of our mining is done in the western portion of this country, but in the old State of Pennsylvania mines and products derived from minerals account for about two-thirds of the entire productive wealth of the State. As our forests are denuded, mining furnishes substitutes for timber in the way of concrete, gypsum board, etc. ; and as civilization increases the wants of mankind, mining is producing metals and minerals of every kind in increasing quantities. For example: during the past ten years the per capita consumption of copper in the United States has increased 49 per cent, to 14.56 Ib.; that of lead has increased 35 per cent, to 12.24 lb.; and that of zinc has increased 70 per cent, to 9.57 Ib. The consumption in European countries is about one-half of this, and there are other countries with large populations where there is virtually no consumption; so when all other countries catch up in consumption with our country, you can see what an enormous demand there is going to be for the metals, even to the extent of having to find substitutes for copper, lead, and zinc.

Jan 1, 1929

By Arthur C. Spencer

IN extension of a suggestion already made to account for certain features observed in the Juneau gold-belt in southeastern Alaska,&apos; it is the object of the present paper to indicate in detail certain conditions in which deformation of rocks under their own weight might lead to the production of fractures in which veins could be deposited. A direct, uniformly-distributed pressure of sufficient intensity applied to an elastic brittle mass offering strong resistance to deformation produces rupture. In a material of ideal properties the surfaces of rupture under such pressure would be shearing planes inclined at 45° to the line of force, unless there be preliminary deformation, in which case this angle would be greater than 45°. This general conclusion, resting upon ana¬lytical mechanics, is completely supported by the results obtained by Daubrée in experiments upon the deformation of wax and resin prisms under compression. Let us then first con¬sider one of Daubrée&apos;s diagrams. In the case illustrated in Fig. 1, four sets of fractures in two appproximately right-angled pairs (that is to say, in conjugate sets) were produced by end-wise compression of the square cross-sectioned prisms. These fractures cut the axis of compression at approximately equal angles, not varying greatly from 45°. The location of the four sets of fractures is obviously determined by the shape of the prism, since the material in each corner acts in a way as a buttress, permitting the bulging to take place most readily on the sides. By limiting the directions in which bulging may take place, results of a more simple nature could be obtained. Take, for instance, a square prism and place it between two fixed and

Nov 1, 1905

By Claude P. Heiner

While the title of this paper embraces the entire West Coast, the author, in the interest of simplification. has confined the discussion to California-particularly the central section. California&apos;s population has, risen 45 pct since 1940. Its electric requirements have also increased, not only because of the growth in industry and population but also because of the widespread tendency of all types of electric consumers to use more electricity than ever before. The growth of California&apos;s electric utilities is shown by published data covering operations, of three of its large systems and is given in Table 1.

Jan 1, 1949

By E. N. Pennebaker

A PRESENT, a comprehensive account of the geology and ore deposits of the Robinson mining district, in eastern Nevada, is not warranted. Though several years&apos; work has been done, the district is so large that it will be some time before the investigation nears completion. In this paper I purpose merely to discuss methods of study and the application of geologic data to the search for ore. In the first place, the purpose of a geological depart¬ment in a mining organization is to collect and correlate all geologic and engineering data likely to be useful. In an extensive and well developed mining camp this involves a detailed study of the structure and stratigraphy of the district as a whole, as well as careful analysis of the orebodies exposed. The problem then is to find continuations or similar ore environments in other parts of the district in which like phenomena have been active, and to explore these for new orebodies. Experience gained in other similar mining districts is useful but one must always remember that a great many mining districts are unique and that exploration rules and procedure applying to one cannot always be transferred to another of apparently similar character and be made to work. One also has to be careful in moving from one to another part of the same district. The geologist must first examine the region critically to determine its individual characteristics. .

Jan 1, 1932

By Thomas Read

IN speaking of immaterial problems of industry I am using the word immaterial in its original sense, not consisting of matter; not in its derived sense, unimportant. There is nothing of a paradox in saying that immaterial problems are the most important in human life, for His a matter of everyday observation that much of the news in the daily papers, and most of the world&apos;s best literature and drama, deal with human conduct that has for its motive forces that are but little concerned with material things. The engineer&apos;s preoccupation with physical forces, in extending his control over them, has not blinded him to the impor-tance of forces that, for want of a better word, I call immaterial; but he has considered that dealing with the one is his job and the other is not. All the evidence of the past decade indicates that the latter are so in-extricably interwoven with the former in modern in-dustrial life that the engineer will have to concern himself with them whether he wants to or not. Some of the most important of the problems arising from the action of these forces relate to the mental hygiene of the workers in industry. Mental hygiene in industry was concisely defined, in terms of the best present knowledge, by Dr. C. Macfie Campbell, speaking last April before the executive com-mittee of the Associated Industries of Massachusetts, and as his statement can scarcely be bettered, I quote it below: "The term mental hygiene is apt to appear vague. The actual stuff with which mental hygiene deals may be briefly reviewed.

Jan 9, 1927

By J. J. Rutledge

FULLY 60 per cent of the serious and fatal accidents in Maryland coal mines are due to falls of roof and side. Usually, the victim of the fall sustains a broken back, sometimes not only the vertebrae being fractured but the spinal cord also being severed. When the spinal cord has not been severed and yet the vertebrae have been broken or injured, it is often possible to rehabilitate the victim of the broken back. - Such accidents are classed as Permanent Total and the victim receives a certain compensation from the State Industrial Accident Commission; sometimes the amount is awarded in a lump sum, but usually it is paid weekly. When the amount allotted to the victim of such an accident has been expended, either in a lump sum or weekly payments, the victim of the accident is dependent on public charity. Some efforts have been made to physically rehabilitate the victims and make them at least partly self-supporting before the expiration of their compensation payments. The State Industrial Accident Com-mission has done some of this rehabilitation. The Maryland Bureau of Mines, in cooperation with R. C. Thompson, Supervisor of Vocational Rehabilitation, State Department of Education, and his assistants, has, through an informal cooperative arrangement, placed several of the victims in hospitals in Baltimore for treatment. Six years ago, through the efforts of the Maryland Bureau of Mines, a dozen or more broken-back victims were examined by an orthopedic surgeon and report was made to the Bureau regarding such cases and the possibility of their rehabilitation. This paper details the result of such examinations.

Jan 1, 1936

By Donald L. Everhart

SOONER or later intelligent exploration for uranium leads to these questions: Where did the metallic ions that formed the orebodies come from? What processes and geologic factors were involved in ore replacement? These matters, of course, make a big difference in how best to look for orebodies. Before these questions are discussed it might be well to point out other factors bearing on the subject. The whole business of uranium exploration is only a little over ten years old, participation by the public is only about six years old, and real interest and activity by more than a few large mining companies has arisen only in the past two or three years. Throughout this short period, uranium exploration has been affected by the unique influences of necessary security measures and by division of the over- all job into individual projects by a large number of specialists in diverse fields. This has meant that a normal interchange of information on the nature of uranium deposits has really only just begun. Com- pared to the vast amount of published studies on iron, copper, lead, zinc, and gold deposits over the past 50 to 75 years, current knowledge of uranium deposits is in its infancy and much of the pertinent information is still scattered about in a number of unpublished sources. The volume of reports on all phases of uranium exploration is now beginning to mount at a remarkable rate, and geologists with widely varying specialized backgrounds in uranium geology are engaging in spirited debates over the origin of uranium and the relative importance of geologic controls of various deposits.

Jan 9, 1954

By F. Keller

ALUMINUM alloys containing magnesium and silicon are susceptible to strengthening and hardening by suitable heat-treatments, and they constitute a class of alloys of considerable commercial importance. Generally, they contain these two elements in the proportions required for the formation of the intermetallic compound Mg2Si, or an excess of silicon; no commercial wrought alloys are made with an appreciable excess of magnesium. The reason for not having excess magnesium is obvious from the results given in this paper, since it is shown that excess magnesium results in a proportional decrease in the solubility of Mg2Si. This is the eighteenth1 of a series of papers from the Aluminum Research Laboratories dealing with the equilibrium relations in aluminum-alloy systems; most of the previous publications concerned binary aluminum-alloy systems; this is the fourth of a group pertaining to ternary aluminum-alloy systems. The work on this system was com-pleted in 1930, but the results were not published because of the pressure of other work. Hanson and Gaylor2, in 1921, presented the results of an extensive investigation of the aluminum-magnesium-silicon system. Their results indicated that an excess of magnesium over the amount required to form the compound Mg2Si caused a noticeable decrease in the solid solubility of Mg2Si in aluminum. A more recent investigation3 in these laboratories showed that the solid solubility of Mg2Si in aluminum was 1.85 per cent at 595° C. and decreased to 0.30 per cent at 300° C. The results of the latter investigation were used as the basis for the present work.

Jan 1, 1936

By W. L. Austin

The only essential difference among the three methods of collecting the precious metals from their low-grade ores by fusion is comprised in the nature of the vehicle in which those metals are concentrated. If lead- or coppper-ores are used, the processes are respectively lead- or copper-smelting; but when the sulphide of iron forms the matrix in which the gold and silver are collected, the process is known as pyritic smelting. The latter method presents rarely any advantages when lead- or copper-ores are available at rates which permit profitable treatment. Pyritic silver-smelting, defined by Percy as " the smelting of silver-ores, which are either free from lead or do not contain it in sufficient quantity to collect the silver, in conjunction with pyrites, in order to produce a regulus in which the silver may be concentrated," is not, as the name would imply, confined to ores of this metal alone, but embraces auriferous silver-ores, or even gold-ores simple. This method of collecting the precious metals from lowgrade dry ores, employed at Freiberg by Barthel Kohler in 1585, does not appear, up to the present, to have been introduced into this country on a working scale. And yet the possibility of getting rid in a single operation of all the earthy or siliceous gangue of a lowgrade ore and concentrating the precious metals in a matte without loss of lead (which includes gold and silver) by slagging, or volatilization, at the same time producing a highly siliceous slag, very nearly if not quite as clean as is usual in lead-smelting, certainly commends itself. In some parts of the country, owing to the com-

Jan 1, 1888

By Arthur Coffinberry

EVE have studied the gold-aluminum system by X-ray diffraction and by the microscope over the entire range of composition for temperatures between 300° and 500° C. Results obtained are shown in Fig. 1, com-bined with the work of Heycock and Neville1 at higher temperatures. The diagram differs in important details from that given by Hansen2 in his critical compilation of the literature of binary alloy systems. This work was, undertaken both because of the intrinsic value of a knowledge of the phase diagram of this system and because of the need of theoretical metallurgy for precise and accurate data, particularly X-ray diffraction data. Systematic studies of equilibrium diagrams, particularly by Hume-Rothery,3 have shown regularities that yield a certain insight into the nature of alloying forces. It has been shown, for example, that solid solubility depends on the concentration of free electrons in the alloy, on the relative radii of solvent and solute atones, on the forces of attraction between atoms, and on the relative stability of intermediate phases. The well-known Hume-Rothery rule states that the crystal structures and compositions of many intermediate phases depend on the electron-to-atom ratio. This has been confirmed and extended by wave mechanical calculations.4 A knowledge of the forces between atoms in alloys, even an imperfectly developed empirical one, should be a valuable guide in the preparation of technological alloys of desirable properties. Furthermore, such informa-tion is basic in such problems as rate of diffusion, age-hardening, phase transformations, and others. The most valuable data for this purpose are furnished by X-ray diffraction studies. Unfortunately, work has been

Jan 1, 1938