Search Documents

By William B. Plank

AGAIN the records show an unprecedented enrollment of students in the mineral technology schools of the United States and Canada. In the current year, 1938-'39, 9619 students were resident in the 53 schools of the United States arid 1014 in the six schools of Canada. These data are from my fifth study of the mineral technology schools of the United States and Canada. the last previous study having been made for the year 1936-'37. The undertaking as previously was made under the auspices of the Mineral Industry Education Division of the A. I. M. E. The data or, the various schools were collected in the same way as for former studies.

Jan 1, 1939

By R. I. Jaffee, E. S. Bartlett, D. N. Williams

The oxidation resistance and fabricability of molybdenum powder-metallurgy alloys containing up to 20 wt pct nickel in the form of a fine dispersion were studied. The effects of dispersion distribution and of amount and type (pure nickel or nickel compounds) of additive were considered. A definite improvement in oxidation resistance was observed, but the amount of improvement fell far short of requirements for an oxidation-resistant alloy. Fabricability by hot-rolling was limited. INVESTIGATIONS at Ohio State university1 and Battelle Memorial institute2 have indicated that the attainment of a truly oxidation-resistant molybdenum-base alloy for high-temperature service, with the coincident retention of high-temperature strength and toughness, will be a difficult, if not impossible, feat. Among the most promising alloy systems studied was the molybdenum-nickel system shown in Fig. 1. Alloys in this system show good oxidation resistance at temperatures well above the normal melting point of molybdenum trioxide because of the regenerative formation of protective nickel-molyb-date (NiMoO4) on the surface of the alloy during exposure at high temperatures. Unfortunately, the required alloy content to obtain oxidation resistant molybdenum-nickel alloys far exceeds the limits of the narrow terminal solid-solution boundary, and closely approaches the peri-tectic composition involving the brittle intermetal-lic compound, MoNi. Because of the peritectic reaction, fusion alloys are characteristically brittle, since the MoNi phase, being the last to form, tends to occur as a continuous grain-boundary network around each molybdenum grain. An added problem with this system is that the protective nickel-molybdate layer formed at high temperatures is unstable, undergoing one or more allotropic modifications upon cooling. The volume changes associated with this modification during cooling are such as to cause violent expulsion of the protective molybdate coating from the surface of the piece. This is, of course, quite detrimental in material exposed to cyclic temperature during service. The research reported here resulted from an attempt to overcome the aforementioned problems associated with the molybdenum-nickel alloys primarily by controlling the amount, size, and location of the MoNi phase. By using powder-metallurgy techniques of alloy preparation and sintering the blended molybdenum-nickel powder mixtures at a temperature below the peritectic reaction temperature, molybdenum-nickel alloys with a randomly dispersed MoNi phase were produced. MATERIALS The molybdenum powder used in the preparation of alloys for this study was commercial hydrogen reduced, minus 325-mesh (Tyler) material. Master alloys, by which nickel was added, consisted of elemental carbonyl nickel powder (12 average particle size), an alloy of 50 wt pct Ni-50 wt pct Cr, and compounds of MoNi, Ni,Si, and Ni2B. The nickel-chromium powder was prepared by filing a vacuum-arc-melted ingot, separating impurities magnetically, and screening to minus 200-mesh. The MoNi powder was prepared by pulverizing a hydrogen-sintered powder-metallurgy compact to minus 325-mesh material. Further sizing of this powder for study of effects of dispersion distribution was accomplished by air classification of the minus 325-mesh powder. The Ni2Si and Ni2B powders were prepared by crushing vacuum-sintered powder-metallurgy compacts to minus 200-mesh material. EXPERIMENTAL PROCEDURE Specimen Preparation—The general procedure followed in the preparation of alloys for testing is described as follows: 1) Blending. Either hand-blending of the powders in a ceramic mortar and pestle for X 1/2 or mechanical blending was used. Hand-blending seemed preferable for optimum homogeneity. 2) Compacting. Most of the blended powders were pressed to green compacts at pressures of 15 tons per sq in. in a single-action die, although some were pressed at 80 tons per sq in. A 1 X 11/4 X 1/4-in. green compact was the standard size for oxidation test material, and 7 X 1/2 X 1/4-in. compacts were used for fabricability test specimens. 3) Sintering. All green compacts were sinteredat

Jan 1, 1959

By P. Duwez, C. B. Jordan

The phenomenon of the change of volume of pressed powder compacts upon sintering is well known in the field of powder metallurgy. Depending upon the metal or metals involved and the pressure used in forming, a compact may, in the course of time of sintering at a given temperature, expand mono-tonically, contract monotonically, or first show a volume change of one sign followed by a change of the opposite sign. It is clearly desirable to have accurate knowledge of the magnitude and sign of the change in dimensions to be expected in any given case, both from the point of view of direct usefulness in the fabrication of parts by powder metallurgy, and from the longer range viewpoint of elucidating the fundamental mechanism of metallic sintering. The present study was therefore undertaken as a first step in acquiring systematic and reasonably quantitative knowledge of the change in density of metal powder compacts during sintering. For practical reasons, copper was selected as the material to be studied first, and its densification followed as a function of temperature and time of sintering in hydrogen and in vacuum. Experimental Procedure The copper powder used was that designated by the manufacturer (Metals Disintegrating Co., Elizabeth, N. J.) as MD-151. This powder was sifted through Tyler standard screens to separate the fraction having particle size range between 200 mesh and 325 mesh, and this fraction was used in all the subsequent work. Compacts weighing about 10 g were then pressed in a 1 in. diam round die, using a pressure of 20,000 psi throughout. Sintering was carried out in commercially built electric furnaces in which the resistance windings are so disposed as to produce a nearly uniform temperature along the axis of the furnace for a length of about 18 in. centrally located. In order to be able to sinter in a controlled atmosphere, a 2 in. stainless steel tubing was inserted in the furnace. Each end of the tube was cooled by a water jacket about 7 in. long, and closed with a rubber stopper. The hydrogen used for one series of specimens was purified as described in Ref. 1. For the other set, a pressure of about 0.5 mm Hg was maintained during sintering by a Welch Duo-Seal Pump. The specimens were heated on square trays made of stainless steel. In placing specimens in the trays, a thin even layer of powdered aluminum oxide was first sprinkled on the bottom of the tray. A copper guard disk about half the thickness of the specimen was then placed in the tray and covered with a second layer of alumina. The actual specimen was then set on the guard disk, and a final coat of alumina sprinkled over the specimen. This technique was evolved for sintering the specimens in such a way as to reduce the influence of unknown extraneous factors to a minimum. If the specimen is placed directly on the tray and sintered, it is found that the resulting shape is that of a frustum of a cone, rather than a section of a right circular cylinder, since friction with the tray prevents the bottom of the specimen from contracting at the same rate as the top. In the arrangement used in these experiments, the guard disk provided a support which shrank at the same rate as the specimen, and the alumina powder reduced to a minimum friction between guard disk and tray, and between specimen and guard disk. The procedure followed in sintering consisted of bringing the furnace to the required temperature, and then inserting the specimen into the central heated portion of the furnace tube in one of the two atmospheres used. At the end of the heating period, the specimen was cooled by bringing it into a portion of the furnace surrounded by a water jacket. These manipulations were carried out without opening the furnace, by means of rods which were attached to the trays and operated through a sliding seal in the rubber stopper. The progress of densification of the copper compacts was studied at 1300, 1400, 1500, 1600, 1700, and 1800°F. At each of these temperatures, a specimen was allowed to sinter for each of the following time intervals: M, 1, 2, 4, 8, 16, 32, and 64 hr. The thickness and diameter of each specimen were measured with micrometers before and after sintering, and each was weighed on an analytical balance after sintering. Results The techniques described in the preceding section were found to give satisfactory results. The specimens were not detectibly warped after sintering, and were usually of uniform diameter (that is, truly round) to within 0.001 in., a very few showing a variation in diameter of ±0.002 in. All specimens were found to have the same diameter

Jan 1, 1950

By G. O. Hiers

IN 1948 in the United States, 184,300 tons of lead was fabricated as coverings for electric power and communication cables. Such covering generally is called "sheathing" for the principal lengths of the cables, while the short lead encasements of the joints are called "sleeves." For the purpose of this paper, both lead sheathing and lead sleeving can fittingly be called lead tubing. In the United States in the same year, 34,262 tons of lead was consumed in making extruded lead pipes. Such pipe is employed frequently for water or chemical solution conveyance with gage pressures up to 100 psi. Consequently, the walls are thicker in ratio to diameter than is the case with the cable sheaths. For this discussion, lead pipes can be thought of as tubes or tubing. About 19 centuries ago, the Romans produced metallic lead of about 99.9 pct purity. Evidently this was cast in flat sheets of Y8-in. thickness, for instance. Such sheet of 10-ft lengths was bent around a removable core producing a tube somewhat oval in cross-section and with a typical internal diameter of, say, 3 in. This method of production necessitated a seam or longitudinal joint evidently made by casting the seam metal adherently. The seam metal, as analyzed recently, contains about 1 ½ pct Sn. Blow pipes were said to have been employed when the joint was made. Specimens of such pipe were found both in Italy and in the British Isles. It is believed the pipes conveyed water for drinking purposes and for baths. Numerous specimens are still in existence in a good state of preservation, due to lead's usual inertness in air or water. According to Claude E. Pearson,1 there were various stages in the evolution of lead extrusion presses for making tubes: I. First press by Joseph Bramah, 1797. 2-First successful press by Thomas Burr, 1820. 3-First bridge die press, J. and C. Hanson, 1837. In 1845, Wheatston and Crooke made the first lead sheathed electric cable. Flat lead strip was wound spirally around the insulated conductor. Overlapping edges of lead were soldered. Early cables were also made by pulling insulated conductors into 50-ft lengths of lead tube. Borel in France, and Wesselau are credited with devising the first presses for extruding lead sheaths directly on cables in 1879. In the United States, Eaton, in 188o, and Roberston, in 1885, introduced new presses of improved design. Following Cunningham's original idea of making lead traps and. bends in 1873, the presses apparently were improved and made successfully soon thereafter. Between the years 1930 and 1940, two continuous extrusion presses for lead were developed abroad. One apparently was originated by Dunsheath and made by the Henley Telegraph Works Co. The other was developed by the Pirelli-General Cable Co. CURRENT PRODUCTION In addition to the several descriptive chapters on lead extrusion in Pearson's book, the Metals Handbook2 recently described pipe, sheath, and collapsible tube production. The latter is by impact extrusion.

Jan 1, 1951

By M. D. Banus, M. B. Bever, A. K. Jena

Measurements of the heat effects on addition of various solid phases of InSb to a solution calorimeter have confirmed the existence of a new high-pressure plzase InSbQII), which was jormed at 37 kbar and 623°K. The heats of formation of InSbQ), InSbfl), and InSb(111) have been measured and the heats of transjormation of InSb(1) to InSb(1l) and InSb(Iii) and of 'InSb(ll) to InSb(iiI) at atmospheric pressure and 78°K have been determined independently. Other thermodynamic properties of these phases, the phase boundary InSb(i)/InSb(ll), and the relative positions of the triple points are calculated. The pressure-Dolume term is shown to be more critical than the internal energy difference in making the phase InSbQ) less stable than InSb(II) at high pressures. Observations on partially transformed specimens suggest that the transformation of' metastable InSb (III) takes place in the two steps InSb(lll) — InSbQI) and InSbQI) — InSb(l). The compound InSb can exist as several phases depending on the temperature and pressure. The phase InSb(I), which is a semiconductor having the zinc-blende structure, transforms into the phase InSb(11) at a pressure of about 23 kbar and room temperature.'-3 The phase InSb(II) has the 6 tin structure,4-6 is metallic, and becomes a superconductor below 2.lok7 An orthorhombic phase of InSb has been reported to occur above a pressure of approximately 30 kbar at room temperature.' This phase is also a superconductor below about 3.4k9 The phase InSb(I1) is retained at atmospheric pressure if it is quenched to 78°K under pressure,6,7 but tends to transform at higher temperatures and does so explosively above approximately 210ok,7 A value of the heat of transformation of InSb(1) to InSb(II) at 210°K and atmospheric pressure has been reported.' A concurrent publication'0 reports evidence for a new solid phase InSb(III), which was formed by annealing InSb above 58 1°K at 37 kbar, above 560°K at 52 kbar, and above 473°K at 65 kbar. Specimens of InSb(II1) had a superconducting transition temperature of 4.lo ± 0.1oK. X-ray diffraction patterns also indicated the presence of a new phase. In this communication, thermodynamic properties of the phases InSb(I), InSb(II), and InSb(II1) are reported and discussed. The phase boundary InSb(I)/InSb(II) and the relative positions of the triple points are calculated. 1) EXPERIMENTAL 1.1) Preparation of Specimens. Specimens of the high-pressure phases of InSb were prepared in a belt-type high-pressure chamber by a tichnique described in detail elsewhere.'' Charges of 0.6 to 0.8 g of Cominco semiconductor grade InSb were used. The temperatures were measured with a chromel-alumel thermocouple, the hot junction of which was within 0.5 mm of the specimen. The specimens were heated under a pressure of 37 kbar for 1 hr at 723°K (which is well above the liquidus) and quenched to room temperature. One set was annealed at 523°K and another set at 623°K for 20 to 24 hr. These annealing temperatures were chosen because 523°K was below and 623°K was above the temperature of the transformation of InSb(II) to InSb(1Tl) at 37 kbar.10 The specimens were then cooled to 125°K by passing liquid nitrogen through the jacket of the belt die before the

Jan 1, 1968

By Samuel H. Dolbear

THE purpose of a technical report is to record facts, usually collected by investigation, and to interpret these facts in understandable language. The audience may range from a small shareholder without technical knowledge, to a highly trained engineer or geologist. If the client is a mining company with technically trained executives, the report writer's problem is relatively simple. The writer will then be appraised not only for his conclusions, but for clarity of language and organization of the report. If the writing is bad, the construction careless, and there is a failure to clearly convey to the reader the facts and the author's conclusions, the report is a failure and the writer may have damaged his professional character. Spoken words die quickly, written words may constitute a permanent record and if they are badly composed they may rise up to damn the author. "A good measure of an author's understanding of his subject is his ability to express it clearly in plain words." Good English Teachers in the fields of mineral technology have frequently complained that even in post-graduate groups there is an appalling indifference to their appeals for good English. Some have even noted a student's belief that the use of refined English is effeminate. If those with such immature beliefs could measure the pay-check damage arising from the use of "sloppy" language, they would realize that precision and refinement in English may be quite as important as technical accuracy. When the reader audience is without technical knowledge simplicity in treatment becomes especially important. If one is engaged in consulting work, in government service, or in any field where reports have public distribution, the language employed should be technically adequate but simple enough to be understood by non-technical readers. For example, one may use the term "visual" in place of "megascopic." Technical language can be so obscure that it cannot be understood even by highly-trained students. In the March-April (Vol. 47-No. 2) issue of Economic Geology, Nicholas Vanserg ridicules these extremes and quotes various paragraphs from published material, such for example: "However, lattice orientation unaccompanied by cognate dimensional orientation can never be attributable to growth from an isotropic blastetrix." "The temperature declines because of cessation of the exothermic chemical and mechanical equilibriopetal processes." These he calls "good geologese" and they are calculated not only to baffle the reader but to impress upon him the erudite character of the author. Revision In some cases, difficulty arises from the fact that the writer is too close to the subject and unconsciously assumes that his reader is equally familiar with the background of the report. It is difficult for the writer to regard his work objectively and to determine to what extent it is likely to be understood. Every important manuscript will gain in clarity if the author will have it reviewed by an informed reader. But the writer must not be oversensitive to criticism and should not treat his composition as perfect and beyond the possibility of improvement. The first draft of a report always requires revision, regardless of the care used or the ability of the writer. Three or four revisions are not uncommon. The first draft usually requires expansion in places, the deletion of non-essential material, and language changes to promote clarity of expression. This should be done by the author after a lapse of time, even if only overnight, in which his mind has been occupied on some other subject. Possible improvements are always more visible. The manuscript should be passed on to another reader for further suggestions. Organization of Material The engineer should study available reports and library references before going into the field. If the previous reports have been responsibly done and can be accepted as correct, then much field time can be saved. It is, of course, customary to make some on-the-ground checks to confirm earlier reports, particularly those relating to ore reserve which may have undergone changes. Report writing requires time and expense, but nevertheless, the basic reasons for conclusions should be presented even in the case of a worthless property, for it may prevent a duplication of the work. If the mine examined is obviously of no further interest, no useful purpose can be, served by preparing a report in detail. In one case an engineer travelled all the way to South America only to find that the mine had been grossly misrepresented and was valueless. His cabled report "Nonsense" is a case of over-simplification, but it served his company's purpose. The first step in report organization should be the selection of subjects. This should be done at the mine, and the data collected for each subject should be reviewed in considerable detail on the ground. Otherwise one may find that he has failed to collect some essential details not readily obtained after he has returned to headquarters. If the property to be described is undeveloped, then many of the subject titles are automatically eliminated. Usually no useful purpose is served by an attempt to calculate the cost of production under such circumstances, although the cost of exploration

Jan 1, 1952

By C. S. Roberts

The creep mechanism and kinetics of fine-grained magnesium have been studied over the temperature range 200&apos; to 600°F. As a result of a photographic study of microstructural changes, transient and steady-state creep components have been correlated with slip, subgrain formation, and cyclic deformation at the grain boundaries. THE approach of this research has been the blend of a quantitative study of the creep strain of polycrystalline magnesium as a function of time, stress, and temperature with direct microstructural observations of the operative deformation processes. The validity of the conclusions is dependent on the condition that the microstructural changes seen on the polished surface qualitatively represent those occurring in the bulk of the metal. The work was intended as much to lay a background to a study of highly creep-resistant magnesium alloys as to provide a description of the behavior of the base metal itself. The spectroscopic analysis of the electrolytic magnesium used in this study is as follows: Al, 0.009 pct; Ca, <0.01; Cu, 0.0011; Fe, 0.021; Mn, 0.012; Ni, 0.0004; Pb, 0.0012; Si, <0.001; Sn, <0.001; and Zn, <0.01. The impurity level is approximately that of commercial magnesium alloys. The original ingot was melted under Dow type 310 flux and cast as a 3 in. diam billet. It was extruded into 1 in. flat stock under the conditions: billet preheat 800°F (1 hr), container and die temperature 800°F, speed 3 ft per min, and area reduction ratio 45:1. The extrusion process was chosen in preference to rolling and recrystallization because it allowed easier grain size control from specimen to specimen. The grains of the extruded metal were fairly equi-axial and uniform in the size range of 4 to 6 thousandths of an inch. The preferred orientation of basal planes about the transverse direction was determined by an X-ray diffraction surface reflection method. A beam of filtered copper radiation was directed at an angle of 17" to both the transverse direction and the surface yet perpendicular to the extrusion axis. Analysis of the (002) diffraction arcs in the resulting photographic patterns gave an approximate intensity distribution along the great circle which extends through the center of the basal plane pole figure and to the extrusion axis poles. Successive layers of metal were removed by macro-etching between exposures. The extruded texture is relatively sharp, but the most significant point is the position of the maximum basal plane pole density and its variation with depth below the surface. Fig. 1 shows that this maximum is rotated 15" from the normal at the surface toward the extrusion direction. Such an inclination has been reported for extruded 1 pct Mn and 8 pct A1-0.5 pct Zn alloys.&apos; The inclination decreases until the maximum splits at about 0.025 in. depth into two elements of equal and opposite rotations from the ideal. The double texture persists to as great a depth as was experimentally convenient to examine. It probably continues to the very center of the extrusion. There is no great change in the sharpness of the individual elements of the texture with depth. A plate of metal about 0.015 in. thick at the surface of the extruded stock was produced by etching. A transmission diffraction pattern was made for the purpose of determining any preferred orientation of a direction in the basal planes. Relatively uniform {loo) and {101) rings were produced. There is little tendency for parallelism of a given direction in the plane with the projection of the extrusion axis on it. The creep specimens were machined from 6¼ in. lengths of the extruded stock. Creep was measured on the reduced section, ½x1/8X2¼ in. long. This section was electropolished on one side for the studies of microstructural changes during creep. An orthophosphoric acid-ethyl alcohol electrolyte was used under the conditions recommended by Jacquet.² Hand polishing was used for previous mechanical preparation. Electropolishing was continued until all mechanical twins had been removed. The electro-polished surface was protected from oxidation during creep testing by a thin layer of silicone oil. All micrographs were taken at room temperature on conventional metallographic equipment and after removal of the oil film. The creep tests were performed with machines which have been described in detail by Moore and McDonald." Five testing temperatures, 200°, 300°, 400°, 500°, and 600° ±3°F were used. Difference in temperature between the two ends of the specimen reduced section was 2°F or less. The testing was done at constant load. Strain readings were taken as frequently as necessary to develop usable creep curves. Tensile Creep vs Time, Stress, and Temperature A definition of terms is necessary. Whenever successive sections of a creep strain-time curve show decreasing, constant, and increasing slope with time they will be termed primary, secondary, and tertiary

Jan 1, 1954

By T. E. Leontis

The specific effect of various rare-earth metals on the room- and elevated-temperature properties of magnesium has been evaluated. Alloys containing didymium exhibit the highest tensile and compressive strengths at room and elevated temperatures. All the rare-earth metals increase the creep resistance of extruded magnesium at temperatures in the range of 400° to 600°F, but the degree of enhancement depends on the temperature and on the concentration of the added metal. THE effects of rare-earth metals on the properties of sand-cast magnesium were discussed in some detail in earlier paper by the author.&apos; The present paper deals with the effect of the same alloying elements on the properties of extruded magnesium. This investigation also had as its aim the development of a wrought alloy having a better combination of room-temperature strength and ductility and elevated-temperature strength and creep resistance than is found in magnesium-Mischmetal-manganese alloys, which have been reported earlier.2-5 The only known attempt to study wrought magnesium alloys containing pure cerium instead of Mischmetal was made by Mellor and Ridley.6 They found that in the form of rolled bars there is a definite, optimum cerium content for creep resistance at 200 °C and that the creep resistance of these alloys at 200 °C is significantly Improved by heat treatment at 550" to 580"C. In the present investigation the compositional variation in mechanical properties of the following alloy systems is presented: I—magnesium-Misch-metal. 2—magnesium-cerium-free Mischmetal. 3— magnesium-didymium. 4—magnesium-cerium. 5— magnesium-lanthanum. Alloys containing predominately praseodymium are not included in this series because of the lack of this material. Experimental Procedures The alloying ingredients used in preparing the alloys described herein are the same as those reported in the earlier paper.&apos; Cerium-free Mischmetal is the rare-earth mixture remaining when the cerium is removed from Mischmetal, which contains all the rare-earth metals as they occur naturally in mon-azite sand, the ore from which Mischmetal is produced. Removal of both cerium and lanthanum from Mischmetal leaves what is commonly called "didym-ium," consisting predominantly of neodymium and praseodymium. Although the composition of the particular batch of each metal used may differ somewhat from the analysis presented previously, these differences are not great enough to warrant repeat- ing the specific composition of each material. The electrolytic magnesium used as the starting material in these alloys has the same typical analysis as that given in the earlier paper.&apos; The alloys were prepared in small laboratory melts applying all the necessary precautions for alloying rare-earth metals with magnesium described by Marande.&apos; Most melts were large enough to cast one 3 in. diam billet 10 in. long. In a few cases, particularly the didymium-containing alloys, the lack of sufficient amounts of the rare-earth metal limited the size of the billet to 6 to 8 in. All billets were scalped to a diameter of 2 15/16 in. and faced to a length of 9 ¼ in. as limited by the size of the extrusion container. The alloys were extruded into ½ in. diam rod on a 500-ton direct-extrusion press using a 3 in. container. The details of the extrusion step are: billet preheat, 925°F (2 hr); container temperature, 900°F; die temperature, 900°F; extrusion speed, 10 ft per min; reduction ratio, 36:1; and percent reduction, 97.3. The lower melting point of alloys containing didymium&apos; necessitated reduction of the extrusion speed to 5 ft per min in order to prevent hot shorting during extrusion. Adequate lengths were cropped from both ends of each extruded rod to assure that all the material used for tests was extruded under uniform conditions. Tensile and compressive properties at room temperature are reported in the several conditions of heat treatment. The ASTM designations are used to distinguish these conditions as follows: T5—Direct age at 400°F (16 hr) T4—Heat treat at 950°F (4 hr) for alloys containing didymium T4—Heat treat at 1050°F (4 hr) for all other alloys T6—T4 + age at 400 °F (16 hr) The lower heat-treating temperature for alloys containing didymium is necessitated by the lower melting point of these alloys. All heat treatments were conducted in electrically heated, circulating-air furnaces. A protective atmosphere containing 0.5 to 1.0 pct sulphur dioxide was used for the high temperature heat treatments. Tension and creep specimens 6 Yz in. long and compression specimens 1½ in. long were cut from the extruded rod. A reduced section of ? in. diam was machined on the tension specimens, whereas on the creep specimens a reduced section of 0.450 in. diam

Jan 1, 1952

By J. P. Nielsen, H. Margolin, E. Ence

The Ti-Ni phase diagram has been investigated up to 68 pct Ni with iodide titanium base alloys by metallographic, X-ray, and melting point methods, and from 68 to 90 pct Ni by examination of as-cast structures of sponge titanium base alloys. NVESTIGATION of the nickel-rich portion of the I Ti-Ni phase diagram was first reported by Vogel and Wallbaum in 1938.&apos; This work was subsequently extended to lower nickel contents by Wallbaum&apos; who indicated the possibility of a eutectic reaction for nickel contents below 38 pct. Long et al.3 studied the titanium-rich portion of the phase diagram and found eutectic and eutectoid reactions below 38 pct Ni. However, the temperature of the eutectic indicated by Long et al. was considerably lower than that suggested by Wallbaum. Long and his coworkers synthesized their alloys by powder metallurgical techniques and encountered oxygen and/or nitrogen contamination. Thus the diagram which was obtained did not represent binary alloying conditions. However from these results the features of the binary diagram were predicted. At Battelle Memorial Institute4 the Ti-Ni diagram was investigated up to approximately 11.5 pct Ni with sponge titanium alloys. The range of temperatures used was not sufficient to define the eutectoid temperature or composition. The data of Wallbaum2 and Long et al.8 were of particular interest for the present study, and although the work was originally concerned with the region below 40 pct Ni, the investigation was extended to higher nickel contents in an attempt to resolve the differences between these workers. Experimental Procedure Preliminary work on the Ti-Ni system was carried out with duPont Process A sponge titanium alloys to reduce the amount of subsequent work to be done with iodide titanium base alloys. The sponge titanium used contained 99.71 to 99.77 pct Ti, 0.1 pct Fe and 0.005 to 0.009 pct Ni. The iodide titanium obtained from the New Jersey Zinc Co. contained 99.9 to 99.95 pct Ti. Nickel used with sponge titanium was 98.9 pct pure. The high-purity nickel alloyed with iodide titanium was cobalt-free with approximately 0.05 pct C and was obtained through the courtesy of the International Nickel Co. The 15 g sponge titanium charges for melting were prepared by compacting in a die or by placing the weighed portions of nickel and titanium directly into the furnace. Iodide titanium charges were made by drilling holes in the as-received rod and inserting the nickel or by wrapping the nickel in sheet. Sponge titanium alloys containing from 0.2 to 90 pct Ni and iodide titanium alloys containing 0.2 to 68 pct Ni were prepared by these methods. In addition to these alloys several 1/2 1b sponge titanium alloys were supplied by the Allegheny Ludlum Co. The charges were melted in an arc furnace under an argon atmosphere. The procedures used were similar to those reported in the literature5,&apos; and the furnace has been described.&apos; Except for iodide titanium alloys with 40 to 68 pct Ni (see section on copper contamination), each alloy was melted for 1 min, then either turned over or broken before re-melting for an additional minute. Currents of 200 to 400 amp were used depending on the melting point of the alloy. Prior to heat treatment, alloys containing less than 14.5 pct Ni were hot-forged at 750°C. With the exception of alloys in the homogeneity range of the compound TiNi, alloys of higher nickel contents could not be hot-forged. Heat treatment of iodide titanium base alloys was carried out in argon-filled quartz capsules which were broken under water at the conclusion of heat treatment to quench the specimens. Temperatures were controlled to ±5oC and annealing times up to 48 hr were used. For melting point determination, specimens were placed in carbon crucibles which were in turn en-capsuled in argon-filled quartz capsules. The start of melting was determined by rounding of corners and by metallographic examination. Complete melting was considered to have occurred at that temperature at which the specimen assumed the shape of the crucible. Specimens were prepared for metallographic examination by mechanical polishing or by an electrolytic procedure." For alloys containing up to 80 pct Ni Remington A etch7 50 pct glycerine, 25 pct HNO,, 25 8 HF) was used. For higher nickel alloys aqua regia and Carapella&apos;s etch (5 g FeCl,, 2 ml HNO,, and 99 ml methyl alcohol) were employed. Specimens to be exposed for powder patterns were prepared by filing, by breaking specimens in a

Jan 1, 1954

By M. E. Wadsworth, T. L. MacKay

Sintered UO, samples were leached in sulfuric acid solutions of various concentrations. A pressurized system was used so that it was possible to investigate the kinetics of the reaction to 270°C with oxygen overpressures as high as 900 psi. The rate was observed to be a function of the concentration of hydrogen ions and directly proportional to the partial pressure of oxygen. Evidences are presented which indicate that a UO2 surface site reacts with a molecule of water to form a hydroxyl complex which in turn can dissociate with the characteristics of a weak acid. A rate determining step has been proposed which involves the reaction between an oxygen molecule and the hydroxyl complex on the surface of UO,. ThE 2 principal methods for uranium dissolution are carbonate and acid leaching. The sulfuric acid leach is the more popular and is used for the treatment of the majority of the ores of Africa, Canada, and the United States. Low recoveries in basic leach circuits led investigators at the University of British columbia1 to study leaching of uranium ores in pressurized vessels. Early in the study of dissolution of uranium it was found that only uranium in the hexava-lent state could be leached in acid or basic circuits. Therefore, the use of oxygen over-pressure in an autoclave offered an interesting approach to solving the low recovery problems of carbonate leaching. UO, was used in this study because it could be obtained in high purity and also because it is representative of the most refractory of the primary uranium minerals. A pressurized system was used to provide a means whereby important temperature and pressure parameters could be varied for the evaluation of the kinetic processes. The mechanism for the dissolution of UO2 should be similar for any of the uraninite type minerals. At the present all of the kinetic studies that have been conducted have been in carbonate media. Peters and Halpern2 carried out a kinetic study of the leaching of pitchblende. Their specimens were pitchblende ores selected on the basis of high grade and homogeneity. Pearson and wadsworth3 conducted a kinetic study of the dissolution of UO2 in carbonate solutions with results very similar to those obtained by Peters and Halpern. EXPERIMENTAL The UO2 as received* was found by spectroscopic *Mallinckrodt reagent, supplied by the Atomic Energy Commission. analysis to have a purity of 99.94 pct 0.03. It was ground in a mechanical agate mortar and screened through a 400-mesh sieve. Thin flat disks of UO2 were prepared by pressing the sized powder in a specially constructed die at a total pressure of approximately 25 tons per sq in. The pressed disks were approximately 0.25 cm thick, 1.6 cm diam, and 3.5 g in weight. As pressed, the samples were approximately 65 pct of theoretical density. It was essential that a binder such as poly-vinyl alcohol be added before pressing to prevent formation of cracks when fired. It was found by trial and error that pressed disks sintered close to 1870°C in a hydrogen atmosphere, reach densities between 91 and 91.5 pct of the theoretical density. At this density the samples had no measurable porosity based upon a 2-hr emersion in boiling water. An X-ray examination of these sintered UO2 disks showed them to be identical with the original UO2 received. Reaction of UO2 with the alundum furnace core was prevented by placing molybdenum between the samples and the core according to the method of Corwin and Eyerly.4 Leaching studies were carried out in a specially designed autoclave, the details of which have been presented e1sewhere.6 The main features of the equipment as applied to a kinetic study are: 1) solution samples may be removed during the course of a single run; and 2) temperature and agitation are carefully controlled. Two-ml samples removed from the autoclave during the course of a run were analyzed for U3O8 content with a Beckman model DK-2 spectrophotometer by the method of

Jan 1, 1959

By F. H. Daniels

IN this, paper it is my intention to, call your attention to* a few of the many producers using blast, now, in common use in Sweden, and also those constructed by the Washburn & Moen Manufacturing Company at their Quinsigamond Works. During a prolonged stay in Sweden the writer had an opportunity

Jan 1, 1881

By Russell B. Cornell, William B. Plank

AT the close of the academic year 1940-&apos;41 the largest number of students ever recorded received their first or bachelor degree in the mineral technology schools of the United States. The total of men thus prepared to enter their professional careers in the mineral industries was 1601, a number nearly 12 per cent larger than two years ago and nearly 75 per cent larger than four years ago. Notwithstanding this increase in the number of graduates and as had been predicted in the preliminary report in February, there was a slight decrease in the total student population of the schools in both the United States and Canada. During the college year 1940-&apos;41, 9133 students were enrolled in the 54 schools of the United States and 764 in six of the seven schools of Canada.

Jan 1, 1941

By Douglas W. Fuerstenau, Kalanadh V. S. Sastry

Based on an analysis of green pellet size distributions and kinetic data on ball growth with taconite concentrates, a ballability index has been developed to quantify ball growth behavior as a function of moisture and bentonite additions. The applicability of the ballability index to such other particulate materials as pulverized limestone and ground magnesite is shown.

Jan 1, 1973

By Cleveland Meeting

Jan 1, 1945

By G. E. Karantzavelos

Anew flotation process to recover alunite from low-grade alunite ores is described. The process begins with run-of-mine ore, reduced to less than 5 mm (0.2 in.), being preconditioned with the reagents before grinding and alunite flotation. From the preconditioning step, ore particles, impregnated with reagents, form pellets that subsequently disintegrate into the pulp during grinding. The second step is basically a standard alunite flotation step. Pilot plant test results show that an alunite concentrate assaying at least 85% alunite and less than 5% silica can be produced. Laboratory and pilot plant results were in excellent agreement, indicating that the new process is a viable means of alunite beneficiation. Plant results, using the new process, were superior to results from conventional alunite flotation procedure.

Jan 1, 1986

By Peter Hood

Data on worldwide geophysical activity in mining exploration programs is collected annually by the Geophysical Activity Committee of the Society of Exploration Geophysicists as part of a continuing service to the industry. The data is obtained by sending out questionnaires to all organizations (which are) known to be carrying out mining geophysical work; the organizations canvassed include mining companies, contractors, government departments and universities. The questionnaire is divided into three sections, namely ground methods, airborne methods and research. In 1968, 515 questionnaires were circulated throughout the non-Communist world and 283 replies were received which is a 55% return. A 67% return was received from the U. S. organizations surveyed so the statistics quoted in this report for the United States are reasonably reliable. This report is published in condensed form, but with emphasis on the United States statistics, with the permission of the Society of Exploration Geophysicists. It was presented at the 39th Annual International Meeting of the SEG in Calgary, Alberta, on September 15, 1969. Worldwide utilization of mining geophysical methods reached a new high in 1968 with total expenditures of United States $41.4 million, compared lo $32.3 million in 1967, representing a 28%, increase. The expenditure distribution by area and type of activity is shown in the graph on page 64. In terms of money spent, ground geophysical surveys accounted for 49% of the total, airborne survey&apos;s 36% and research 15%. The percentage of the money spent on ground geophysical surveys fell by approximately 7% from 1967, that for airborne surveys, increased by 5%, and for research the amount increased by 2%. Industry accounted for 79°1% of the total monies spent on mining geophysical activity in the world in 1968 and governments and universities 21 o%.

Jan 1, 1970

By Eckley B. Coxe

SINCE our last meeting, the Institute has lost, by the death of Mr. Gowen, one of its most distinguished members. I shall only attempt in this place to give a brief account of his many accomplishments and achievements; but our records would certainly be incomplete without a recognition of the important influence which he exerted upon the mining and metallurgical industries of this country, and a testimony to his private virtues of character. Although Mr. Gowen was best known as a great lawyer and as the head of a great railway corporation, he began his career, before he was of age, as the manager of a small anthracite blast-furnace at Shamokin, Northumberland County, Pennsylvania. He left this position, to engage on his own account in the mining of anthracite coal at Mt. Laffee, near Pottsville. This proved an unprofitable business, and, after the panic of 1857, he began the study of the law. As soon as he was admitted to the bar, he at once entered upon the active practice of his profession, and soon achieved an extraordinary success. In 1869 he was made President of the Philadelphia and Reading Railroad Company, and he afterwards organized the Pliladelphia and Reading Coal and Iron Company, the largest coalmining corporation in the world. He became a member of. this Institute during the first year after its organization, and remained a member until his death. He always took a deep interest in the work, and was prompt to co-operate by all means in his power in furthering the objects of the Institute. Mr. Gowen was one of the first to recognize the great importance to both miner and consumer, of the proper utilization of the small

Jan 1, 1890

By Fred Beasley

METALLURGISTS have, in the past ten years, overcome many difficulties of high zinc in lead blast-furnace slags. This problem was brought to the front at the close of the late war, by the price obtained for lead and the high cost of labor, fuel, and flux. The Port Pirie plant of the Broken Hill Associated Smelters, Australia, early in 1919 had increased the zinc oxide in its blast-furnace slags from 13.5 to 20 per cent., at the same time reducing the iron oxide in the slag from 33.5 to 25.6 per cent. These results were obtained by the following proceduret the addition of granulated slag to the roaster charge, 10 to 12 per cent., improved conditions of the crushing and mixing and roasting of the constituents of the sinter. By experiments and improve-ments the practice at this plant has developed a normal slag that carries 22 per cent. zinc oxide, and at times runs as high as 33 per cent. zinc oxide, with only slight furnace trouble. The granulated slag is used not, only as a diluent to the sulfur in the roaster charge, but also on account of its value as a slag-forming material and on account of the physical properties it imparts to the finished sinter. The ore is mixed with flux and given a double roast. All the first roasting is by sintering with the Dwight & Lloyd machines. The final roasting is performed partly by Dwight & Lloyd machines and partly by H. & H. pots. The charge to the blast furnaces consists chiefly of the final sinter, slag shells, siliceous and non-bearing sulfur, lead ores. High blast and ore columns are the practice. The greatest care is taken to obtain in the final sinter as low a sulfur content as possible.

Jan 2, 1925

By Samuel Dolbear

PUBLIC discussions of mine finance in the tech-nical press have been confined mainly to methods of providing funds for the development of pros-pects or other mining operations which have not reached the stage of productivity. The application of modern financing methods to mines which have behind them a successful record of net earnings has, for some reason, been given scant consideration by mine owners and managers. In a few conspicuous cases, such for example as the Anaconda Copper Mining Co., Chile Copper Co., and one or two others, industrial finance has been applied to mining operations on the scale and after the fashion of other operations. When extensions are needed re-course is usually had, however, to the sale of common stock, with the obvious disadvantage of diluting the holdings of every stockholder of record prior to such financing. In some cases, it has been sought to over-come this disadvantage by issuing stock purchase rights to shareholders of record. If the stockholder is in a position to acquire additional stock, he may then pre-serve his interest intact, otherwise he must suffer a dilution of his holding. If he purchases additional stock he is, from one point of view, paying more for his in-terest than he bargained for when he made his original purchase. In many cases development and equipment are paid for out of surplus or current earnings. It is sometimes most difficult to explain to a manager why he can afford to borrow money when funds are available from a sur-plus account. Nevertheless, industrial enterprises with adequate surplus accounts often finance new construc-tion by the issuance of bonds. Such a procedure enables the company to maintain its surplus intact, and to con-tinue the payment of dividends during a temporary period of unusual expenditures.

Jan 2, 1927

By C. K. Leith, W. J. Mead

In 1911, we published in the Transactions a brief account of the lateritic alterations of serpentine in eastern Cuba, producing the important iron-ore deposits of the Mayari and Moa districts.&apos; The special feature of that article was a quantitative treatment of the alterations, based on analyses, to show just what had happened in terms of chemical, mineralogical, and physical changes. Professor Kemp has published an interesting account of these ores, containing additional quantitative observations of his own, tending essentially to confirm the nature of the changes that had been worked out.2 His discussion suggests to us the desirability of publishing certain additional quantitative data which were not included in our previous article. This seems especially desirable because quantitative measurements of lateritic alterations are rare, and this particular case may be regarded as typical of a fairly wide range of alterations of this kind. At the time of our examination of Mayari and Moa deposits 29 complete analyses were supplied us by the chemists of the Spanish-American Iron, Co., representing a graded series from the unaltered serpentine rock below to the ore at the surface. These analyses are given in the accompanying table. The mineralogical composition of the ores and rocks is comparatively simple and can be easily calculated from the analyses. In Fig. 1 the mineralogical changes from the serpentine rock below to the lateritic iron ore above, based on the analyses, are expressed in terms of weight, assuming alumina to have remained constant during the alteration. It is not easy by mere inspection of this table of analyses to determine what the progressive chemical changes have been in development of the ore. In order to bring this out clearly, the analyses have been graphically represented in Fig. 2 in such a fashion as to show the progressive additions and losses of substances during alteration.

Jan 1, 1916