Search Documents

By Y. C. Liu, R. H. Richman

The effects of gel,manium and tin on the deformation and 9-e-crystallization textures of copper have been explored in detail with in the copper-rich terminal solid solutions. Addition of solute to copper produces a change in deformation texture from the copper type to the 70 :30 brass type. This transition has been measured quantitatively The types mid proportions of recrystal-lization components have been determined as a function of com-position, and correlation of recrystallization components with specific deformation components is discussed. On the basis of information available in the literature, it has been suggested that the effect of solute elements on the recrystallization texture of copper

Jan 1, 1961

By T. R. Armstrong

Total crude oil production in Mexico in the year 1941 is estimated at approxi- mately 41,000,000 bbl.; a daily average of 112,700 bbl. and a decrease of about 5 per cent as compared with the daily average of 120,000 bbl. produced in the year 1940, and nearly 11 per cent decrease as com-

Jan 1, 1942

By T. R. Armstrong

Total crude oil production in Mexico in the year 1941 is estimated at approxi- mately 41,000,000 bbl.; a daily average of 112,700 bbl. and a decrease of about 5 per cent as compared with the daily average of 120,000 bbl. produced in the year 1940, and nearly 11 per cent decrease as com-

Jan 1, 1942

By C. M. Smith

DELEGATES from 26 Local Sections and- Divisions of the Institute had three stimulating sessions during the Annual Meeting, a few topics still remaining to be discussed after the two Monday sessions.. The final session was held on Thursday morning. An abstract of the discussion will be transmitted to each delegate present. The topics included: Student relations. Section operation, membership, employment, MINING AND METALLURGY, a new nonmetallic minerals Division. licensing of engineers, and increased allotments of money to Local Sections. Some of the Sections felt that the present limit of $250 allotted to them - from the national treasury was insufficient to carry on their activities, and that this maximum should he increased. A resolution to this effect was passed for transmission to the Board of Directors.

Jan 1, 1935

By R. E. Somers

I. Introduction...........................604 1. Location, Topography, and Climate...............604 2. Scope of Work and Acknowledgments...............606 3. History and Mining......................606 11. General Geology.........................609 1. Introduction...........................609 2. Granite. :..........................610 3. Quartz Porphyry......................... 612 4. Monzonite........................... 614 5. Volcanic Breccia........,................ 618 6. Gravels............................. 619 111. Economic Geology......................... 619 1. Introduction........................... 619 2. Mineralogy........................... 619 3. Occurrence of the Ores...................... 622 4. Oxidation and Downward Enrichment............... 630 5. Rock Alteration........................639 6. Genesis of the Ores........................ 643 I. Introduction 1. Location, Topography, and Climate The Burro Mountains are located in the southwestern part of New Mexico, in Grant county. The group is made up of two distinct mountain masses, known as the Little Burros and the Big Burros, the former lying about 6 miles southwest of Silver City, and the latter about 9 miles farther in the same direction. They are separated by the valley of the Mangas River, a tributary of the Gila, and a stream only in name, except after a heavy downpour of rain. The Little Burros attain an elevation of 6,625 ft. above sea level, and the Big Burros 8,054 ft., with the surrounding country averaging about 6,000 ft. To the south of these mountains stretches the desert plain, while to the north are the more frequent elevations of the mountainous country.

Jan 1, 1916

By Earl E. Hunner

At the end of the year 1914, the main North Star incline shaft had reached the 6300-ft. level, and encountered a vein dipping southwest, or exactly opposite to the North Star. Subsequent development failed to find the North Star vein continuing beyond this intersection, so the 6300-ft. level proved to be the bottom level of the North Star vein, and very little ore was found below the 5300-ft. level. The new vein was called No. 1 vein. Development work carried on for the next 10 years discovered a third vein, called No. 2, branching off about 1200-ft. to the east, with a north-south strike and a west dip. No. 1 vein had about 900 ft. of backs above the 6300-ft. level before reaching the boundary line of the property, and No. 2 vein died out about 800 ft. above. During these 10 years, the money spent on development was increased from $54,000 in 1914 to $184,000 in 1924; the ore reserves steadily diminished until it was evident that the mine must close down unless by some means a large tonnage of ore could be developed quickly. Problems and Plans In order to understand what follows, the general layout and equipment of the mine as it was at this time must be briefly described. Fig. 6 indicates the relative positions of the shafts. The North Star (incline) shaft extends from the surface to the 6300-ft. level following the vein, with an average pitch of 26", between limits of 11" to 38. There is at present no hoisting equipment in this shaft between the 2700 and 4000-ft. levels. The Central (vertical) shaft connects with the North Star shaft at the 4000-ft. level, at a vertical depth of 1600 ft. In two compartments of this shaft 4-ton skips made a vertical turn of 15 ft. radius at the 4000-ft. level and ran down the incline to the 6300-ft. level. A cage operated in the third compartment to the 4000-ft. level. Men and supplies were transferred to a truck running on a third track down the incline shaft to the 6300, operated by an electric hoist on the 4000-ft. station. When the shifts changed double-deck cages were substituted for the skips in the vertical shaft, but they stopped at the 4000-ft. station. The truck to 6300 carried 22 men, and it required 8 min. to make a trip down and back. This arrangement was satisfactory as long as a fairly large proportion of the work was

Jan 1, 1930

By Albert Sauveur

THE senior author of this paper has expressed the belief that when gamma iron transforms into alpha iron on reaching the A3 point, each gamma grain does not change bodily into one or more alpha grains but that the alpha phase forms first at the boundaries and along the crystallographic planes of the austenite grains.1 To quote: On cooling through the point A, at about 900° C., iron passes from the gamma condition to a. new allotropic form generally designated as alpha. This transforma¬tion, however, is not instantaneous. There are good reasons for believing that it begins at the grain boundaries and along the octahedral planes of the crystals and that it progresses until each grain of gamma iron is changed into a grain of alpha iron, the resulting structure being similar to that of gamma iron. Were it possible to retain at room temperature pure iron but partially transformed, it seems probable that a Widmanstättian structure, or rather, as later explained, a martensitic structure would be observed (Fig. 1), consisting of alpha iron at the boundaries and at the octahedral planes, and of a groundmass of gamma iron. In order to confirm, if possible, the accuracy of that view, a number of experiments were conducted. Polished samples of electrolytic iron were heated in a vacuum, maintained in the gamma range for several hours and quenched in different media. It was hoped by such means to produce and retain on the polished surfaces a pattern which would reveal the mechanism of the allotropic transformation. The samples were placed in evacuated quartz tubes, heated to 1000° C. and held 2 hr. at that temperature. The tubes were then immersed in the quenching bath. Iced brine and liquid air were used first. The polyhedral austenitic structure existing at the time of immersion was very clearly revealed (Fig. 2). This is generally ascribed to iron volatilizing at the grain boundaries.

Jan 1, 1929

By Michael Tenenbaum

Selected characteristics of nonmetallic phases were determined in low-carbon sheet steels which had been produced by various refining; deoxidizing, and casting procedures. The results showed little influence of the refining process on the quantity, distribution, size, and character of the nonmetallic phases. The quantity of inclusions was governed by the deoxidation procedures. While the mode of casting influenced the internal structure and the pattern of inclusion distribution, it had little effect on the quantity of nonmetallics. The vast majority of inclusions were under 30 µ in diam, and there was little change in size distribution during hot and cold rolling. The composition and structure of the inclusions were expained an the basis of known equilibrium phase diagrams for the appropriate systems. Additional work is needed to explain some of the observations of this paper. HENRY Marion Howe's contributions to the metallurgical profession include his many writings, the wisdom that he imparted to his students, and the inspiration that he gave to the many scholars, teachers, and industrialists who knew him personally. It was Professor Howe's intimate colleague, Albert Sauveur,1 who, in the first Howe Memorial Lecture, could have been speaking for the metallurgist of our generation as well as his own when he wrote, "...how many of us on the point of going astray were called back to the right path by Howe's guiding torch?" More than a quarter of a century later, Francis Foley,2 one of the last in the Howe Lecture series who worked directly with the great man, delivered the ultimate tribute, "...truth, in its time is so hard to identify." While Professor Howe strove to be right, "he was content if he provoked the reader to take the next step along the path to greater knowledge." Like so many of my predecessors, I sought guidance for this lecture by referring to Professor Howe's two classic texts, Metallurgy of steel,3 and Metallography of Steel and Cast Iron: the former book interpreting the facts as he saw them near the start of his career, and the latter—published 26 years later—pointing to many fertile fields for metallurgical investigation. Those of us who harvest the fruits of Henry Marion Howe's contributions to the metallurgical profession now look with wonder at the tremendous legacy he has provided. It is rewarding to study his writings and to recognize the anticipation of such aspects of modern ferrous metallurgy as: 1) Direct reduction 2) Steelmaking reactions 3) The approaches and benefits of degassing 4) Solidification mechanisms 5) Habits and behavior of nonmetallic inclusions 6) Recrystallization phenomena 7) Slip and slip propagation 8) Dislocations 9) Discontinuous deformation 10) Microscopic and macroscopic segregation

Jan 1, 1970

By W. H. Andrews

THE constantly increasing consumption of Portland cement in the State makes the above subject of partlcular interest at this time. The increasing demand is due to the rapid settling of the country and the fact that new uses are being found frequently for the above named commercial article. The industry is one that is bound to grow as the population increases, and this being the case, it may be well ,it this time to consider briefly- the matter of the chemical and physical com-position of proper raw materials. A cement mixture is one that contains approximately 75 per cent. carbonate of lime, 15 per cent. Silica, and 5 to 7 per cent. alumina, and iron oxides; the other elements being magnesium carbonate and small quantities of the rarer elements general associated with limestone deposits. It call be readily seen from the above composition that it is possible to build up this mixture from a number of different materials. First.-A rock high in carbonate of lime can be mixed with clay or shale in such proportions as to bring about the desired composition ; the chief difficulty in the building up of such a mixture is that it is hard to find a clay or shale in which the silica-alumina, ratio lies .between 4 to 1 and 3 to 1 and at the same time shows physical characteristics which will make certain its adaptability to the practical manufacture of Portland cement. Very often clays or shales are found which are right chemically but contain large quantities of grit or free silica. Such clays or shale must be ground to extreme fineness in the mixture in order to make the silica and alumina combine with the lime when the mixture is burned. On the other hand, clays or shales are often found that have the proper physical characteristics but in which the amount of alumina, is too great.

Jan 9, 1913

By Ta M. Li

How do you convert a copper-zinc resource into a viable economic mining operation? This problem, unlike most, was complicated by the additional presence of a sub-arctic climate, highest labor costs in the world, low-grade copper-zinc values, depressed market prices, and a complex mineralization.

Jan 12, 1977

By John A. E. M. Church

THE prospector's pan was the first implement used for saving gold, and its action is so effective that it has never been equalled for thorough work. Copper plates, blankets, sluices, and amalgamators of several patented designs have thrust it aside, but in spite of all the advances made there is no dispute among experienced men as to the comparative thoroughness of the work done by it and its rivals. When its rivals are doing their best, the pan can take their discarded refuse and prove their inefficiency by producing from it not only gold, but even the mercury which has been lost from the machines themselves. The trouble with the pan has always been that it was only a tool. Man was the machine that moved it. His work was high-priced, the quantity treated small, and it was impossible to use the pan for any but the richest sands. As a consequence the best gold-saving appliance known has been discarded for years and replaced by machines of inferior excellence, but which could more than make up for their limited ability in saving gold by their capacity for treating great quantities of ore. Mr. Peck is one of the old-time amalgamators of the Comstock district, and the first idea of the new machine came to him as he used to pan below the tailrace of his mill. No matter how fine the work of the mill was, the pan invariably proved that better could be done. The tailings always contained gold, silver, and mercury. This state of things is just as true to-day, after all the improvements that have been made, as it was then, and the much-vaunted method of the " Washoe process" consists in extracting 72 per cent. of the gold and silver by one operation, and then repeating this operation half a dozen times to get out about one-third of the remainder. With all the advances of twenty years in milling, there is nothing more crude in metallurgy than the treatment of tailings in many of the large mills of the West.

Jan 1, 1880

By John A. Church

Jan 1, 1880

By AIME AIME

THE petroleum engineers have the conference habit. They drop in, thresh things over, and drop out. No time is wasted. So it was at the Fort Worth meeting of the Petroleum Division, Thursday and Friday, Oct. 8 and 9; headquarters, Blackstone Hotel. Associate Chairman Albertson arrived the morning of the 7th, to tie in any loose ends of the technical program. S. M. Greenidge, chairman of the local committee, checked the arrangements with his committeemen at a luncheon that noon. By mid-afternoon the next day's attendance was anybody's guess-there were no noses to count. But when the gavel sounded Thursday morning 175 members and guests were present, also the official A.I.M.E. party consisting of President Lovejoy, Secretary Parsons, and George Otis Smith. Shortly after adjournment Friday afternoon all but a handful had vamoosed, lit out, disap¬peared. But, in the meantime, it was a grand conference, attendance maximum every session, and the discussion fast and furious. The discussion came from all over the floor, sometimes as good-natured sniping, sometimes in long volleys that were almost fatal to the reporter. Everyone knew his subject and few there were who had nothing to say.

Jan 1, 1936

By C. S. Harloff, Frank R. Corwin

THE Nichols Copper Co., associated with the Phelps Dodge Corp. and the Calumet & Arizona Mining Co., has constructed at El Paso, Tex., and is now operating a copper refinery with a yearly capacity of 100,000 tons of anodes. Transportation facilities were perhaps the most important of the considerations that led to the selection of this site. The rapid industrial development of the Middle and Far West has increased the consumption of copper there. The advantage of local refining as against shipping the copper to the Atlantic sea- board is apparent. Copper refined in the Southwest is equally competitive for export shipment, either from the Gulf or the Pacific Coast ports. The tonnage of copper produced in the Southwest not only justifies the construction of this plant, but may warrant considerable expansion in years to come.

Jan 1, 1930

By J. F. Lewis

BELIEVING that one of the essential points in mining, as in all other business, is to know the expense incurred in each particular department, I have carefully kept an account with each department for the past three years; and, as it may be of interest to some of our members, I herewith present it to the Institute, reduced to percentages of the total yearly expense, showing the cost for materials, repairs, expenses, tools, team accounts, powder, oil, and fuel, also for labor under its several heads :

Jan 1, 1878

By J. F. Emig

The Burns Harbor Plant was designed to produce and process large ingots into plate, hot rolled sheet, cold rolled sheet and tin plate. Rimmed ingots, in particular, are poured 96" to 106" high and weigh up to 85,000 lbs. During the latter part of 1970, a quality problem was encountered involving white line "sliver" defects on the surface of cold rolled, low carbon, rimmed steel sheet. Sheets containing these defects are not desirable for exposed automotive items because of the possibility of opening during forming or becoming more apparent after forming. Metallographic work located and identified two basic types of inclusions within the white line defects: (1) complex oxides consisting largely of iron and manganese oxides and (2) scale-type iron oxide. The presence of these oxides strongly suggested that the-white line defects were resulting from an unsound, unclean rim zone.

Jan 1, 1972

By J. W. Dougherty

THE Hollinger gold mine is in the Porcupine mining division, District of Cochrane, in the northern part of the Province of Ontario. The adjacent town of Timmins, with a population of 25,119, lies 490 miles by railway north of the city of Toronto. GEOLOGY The property is situated on the northwest limb of a major syncline, which pitches northeast at approximately 50°. The principal rocks of the Hollinger area are of pre-Cambrian age and consist of altered, schistose, Keewatin lava flows intruded by stocks of schistose, quartz-feldspar porphyry generally assigned to the Algoman period. The structure of the Keewatin series is extremely complex as a result of close folding and some faulting. The schistosity, trending north 70° east and dipping steeply to the southeast, is most highly developed along a subsidiary anticline in which the major porphyry bodies occur. The ore bodies, which exhibit three principal structures, consist of quartz veins and associated pyritized wall rock. Some lodes are com-posed of en echelon veins, others exhibit a main quartz body with branch-ing stringers and a third consists of a single definite lead. Gold, in a coarse visible form, may be confined to quartz in some ore bodies but in others it is finely divided and is found not only in quartz but also asso-ciated with pyrite in the adjacent wall rock. In many veins the dis-tribution of gold is such that there are several ore sections, separated by areas of low-grade material, in the same vein although its physical appearance remains unchanged.

Jan 1, 1940

By J. D. Lubahn

Prior tests by Dorn, where the strain rate in a tensile test was suddenly changed, have shown a small, but definite rate-history effect to exist. If this effect is neglected in the calculation of creep behavior from tensile results, an error should occur. This paper shows that this error is smaller than experimental scattering, and may be neglected. DORN1 has found a small but definite rate-history effect in the aluminum alloy 250 at liquid-nitrogen temperature using tensile tests with an abrupt rate change. Such an effect is to be expected from pre-viously known2-6 temperature-history effects, together with general experience that effects produced by changing the strain rate a large amount are simi-

Jan 1, 1959

By Charles Maier

IT has long been supposed that when crystalline materials are com-minuted the energy used in the production of increasingly smaller grain sizes is not entirely dissipated as heat but that a certain portion is "stored" as a part of the internal energy of the material. This portion usually has been called the "surface energy" of the particles. The practical interest of the Bureau of Mines in this subject in connection with the energy requirements of crushing processes has led to the author's attempt to measure the "stored" energy in finely divided calcite by heat-of-solution methods1. The experiments on calcite showed that "storage" of energy could not be proved for this material, because fine grinding caused a lack of chem-ical homogeneity evidenced by loss of carbon dioxide and subsequent adsorption of water on the surfaces of the calcite particles. When thermochemical correction was made for composition changes the cor-rected heat of solution was less for fine material than for coarse. Con-tinuation of the experimental work into the problem of comparing work and heat in the deformation of metallic crystals, where the calorimetric difficulties were less, showed, however, that in the case of copper and aluminum a real discrepancy between work and heat could be shown. similar results had previously been obtained by Farren and Taylor2 and Hort3 and more or less simultaneously with the author's work by

Jan 1, 1936

Meeting, June 26, 1913).-On the petition of 29 members residing in and near San Francisco, Cal., the San Francisco Local Section was established. The territory of the St. Louis Local Section was established to include the following States and parts thereof: All the State of Missouri ; That part of the State of Illinois south of and including the city of Urbana ; That part of the State of Indiana south of and including the city of Indianapolis ; That. part of the State of Kentucky west of and including the city of Frankfort ; That part Of the State of Tennessee west of and including the city of Nashville That part of the State of Arkansas north of and including the city of Little Rock.

Jan 7, 1913