Search Documents

By Alfred Boyles

The experiments described below are a continuation of work on the graphitization of cast iron conducted as part of the program of fundamental research at Battelle Memorial Institute. In previous work it was found that melting in hydrogen increased the amount of eutectic carbide appearing in certain alloys and in others produced marked changes in the size of the graphite flakes. These effects seemed to be closely related to the amount of sulphur and manganese present in the material studied. Iron-carbon-silicon alloys did not respond to hydrogen in the same manner as cast iron and there was no evidence to show that hydrogen was able to stabilize the carbide in such alloys unless additions of sulphur were made. The two alloys examined contained about 2 per cent of silicon. The present paper is concerned with alloys of lower silicon content and describes the structural changes produced by melting in various atmospheres at pressurcs ranging from a partial vacuum up to 300 lb. per sq. inch. Experimental Method The experimental technique was similar to that previously employed, so that direct comparison might be made with earlier work. Alloys were

Jan 1, 1939

By W. G. Bearden, G. C. Howard, J. W. Spurlock

An investigation of the factors af-fec.ting the inter-zonal flow of fluids in the casing-wellbore annrc1rt.s of an oil or gas ivell is presented Laborntory tests revealed that failure of the caring-cement bond allows communi-cation of fluid at pressure differentials near 1.000 psi. Perforating with a 11011011: carrier gun does not shatter or crack the cement sufficiently to allow communication through these cracks and does not seriously affect the casing-cement bond failure pressure. The pressure to cause communication at the casing-cement bond can he increared to 3,000 psi by. limiting pipe deformation during cementing and subsequent operations. Communication can be prevented, however. up to pressures sufficient to cause the cement to fail or the casing to col-lapse, by attaching to the casing a seal ring of deformable ruhber molded between two steel flanges. When installed, one flange is attached rigidlv to the casing to serve as back-up for the gasket While tile other flange is movable. To date, these gasket seal rings have been field-tested in 27 Wells. Althotrgh communication has been noted in two wells, inter-zonal flow has been prevented in other wells in the same area by installing more seal rings between the communicaring zones. INTRODUCTION The inter-zonal flow of fluids behind casing cemented in oil wells during normal production or stimulation operations is a major operating problem. If it cccurs during production operations. it can seriously limit the pressure to which a reservoir may be depleted without harmful invasion of unwanted fluids. If it occurs during stimulation operations, it may preclude the possibility of stimulating the desired zone. This communication can be caused by failure of the bond between the casing and cement, failure of the bond between the cement and formation, or failure of the cement itself. This paper presents the results of an investigation of factors affecting com-munication at the casing-cement bond and methods which aid in preventing it. LABORATORY INVESTIGATIONS The laboratory tests performed in this study were divided into three phases. The first phase consisted of tests to determine if perforating would shatter and crack the cement sheath so severely that communication would occur through the cement itself. The second phase consisted of tests to determine more precisely the cause for the casing-cement bond failure. The third phase consisted of tests to evaluate the effectiveness of various de-formable seals attached to the casing in preventing communication. EFFECT OF PERFORATING, The effect of perforating was invest~gated in tests performed with apparatus shown on Fig. 1. Cement was poured into the annulur space hetween 5%-in. casing and 8%-in. casing and allowed to cure for 72 hours. The apparatus was then perforated with a hollow carrier gun containing eight duPont 26-A shaped charges. Bull plugs were placed over the perforations in the 8 5/8-in. casing and hydraulic pressure was applied inside the 5 1/2i-in. casing. The pressure to cause fluid communication past the cement sheath was observed and termed the "bond failure pressure". Several different cement compositions were included in these tests, the results of which are shown in Table 1. In Tests 1 through 4 of Table 1, bond failure occurred at- the inter- .

Jan 1, 1966

By Robert T. DeGavre

INTRODUCTION The $645 million financing for Inco Ltd's Soroako nickel project in Indonesia not only represents a significant human achievement but also there are certain important lessons that can be derived from Inco's experience in financing the project. The paper will not present a technical assessment of the project since Inco Ltd. submitted a series of papers on this subject at the international Laterite Symposium as part of the 108th Annual Meeting of the AIME in February 1979. BRIEF HISTORY OF THE SOROAKO PROJECT Table 1 summarizes the milestones achieved in the Soroako project and its financing. Exploration Phase A contract of Work was signed on July 27, 1968 by the Republic of Indonesia and F.T. International Nickel Indonesia (P.T. Inco) covering an extensive area of over 25,000 square miles on the two southeastern arms of the island of Sulawesi. The Contract provides that P.T. Inco has the sole responsibility for financing the project and determining the terms on which the financing should be obtained, that P.T. Inco has the right to receive and hold outside of Indonesia foreign exchange revenues and to freely dispose of such revenues, and that Indonesians have the right to purchase up to 20% of the equity of P.T. Inco over a period following start of production. P.T. Inco began field investigations in the Contract Area in August 1968. Preliminary reconnaissance sampling with portable drills broadly outlined areas of favorable laterite terrain which were then systematically sampled on surveyed grids. By early 1971 sufficient exploration work had been completed to indicate that the laterite deposits near Soroako could sustain a major nickel-producing plant (figure 1). Pilot plant studies in 1970 and 1971 at Inco's research station in Port Colborne, Ontario, using two bulk samples of Soroako ore material, also confirmed that the ore could be upgraded and treated for the recovery of its metal values. Feasibility Phase Encouraged by the results of its exploration program and pilot-plant work, Inco Ltd. commissioned Toyo Engineering Company of Japan in August 1971 to prepare a capital cost estimate for a relatively small nickel project called "Stage I". Stage I was to be a single-line pyrometallurqical process plant with an annual capacity of approximately 15,000 metric tons of nickel contained in 75% nickel sulphide matte (see Figure 2). Electric power was to be supplied by a thermal power station. It is important to recognize that Inco's strategy was to develop the Soroako ore deposits in several stages: first, construct a small project to gain experience and to reduce the initial capital outlay and then later expand in one or more steps to a much larger project to achieve maximum economies. The strategy reflected both Inco's financial position in 1971 as its sales and earning dropped sharply and the difficulties previously experienced by Inco in trying to launch in the late 1960's very large "greenfield" nickel projects in New Caledonia and Guatemala. Toyo's Project Development Study was completed. in January 1972. Based upon Toyo's cost estimate for physical facilities, Inco estimated the total capital cost of Stage I to be $115 million. For the next several months, Inco ran numerous in-house financial feasibility studies, using as inputs Toyo's cost estimate and the results of its exploration and pilot plant programs. In September 1972, Inco completed a project feasibility study which was based upon a capital cost estimate of $135 million. The feasibility study was immediately made available to potential partners and lenders. Partner Negotiations The Japanese nickel market had from the outset been central to Inco's planning for the Soroako project. That market had been growing dramatically at rates in excess of 20% per annum during the 1950's and 1960's. Japan had established, for rational security and other reasons, a domestic

Jan 1, 1985

By L. E. Shiffman

W. J. Parton—Those operators faced with the problem of treating fine coal whether in bituminous or anthracite will find this paper most timely. I would like to take this opportunity of discussing Mr. Schiffman's paper and at the same time express certain views relating to our Tamaqua plant. I would like to ask the author what type of impeller and diffuser is used in the Denver cells? Screen analysis of products from individual cells indicate that coarser material resists flotation and only floats after greater retention time in the last few cells. Also, the need for a scavenger screen to reclaim non-floated coal particles further stresses this point. I have always felt that more efficient means of cleaning coal between 10-mesh and 28-mesh existed than flotation. Reagent and power costs are high for the flotation process. When floating +28-mesh particles, cell capacity is lowered and some of the particles are lost with the refuse. The Tamaqua plant of the Lehigh Navigation Coal Co. floats —28-mesh coal and capacity of recoverable coal is 40 tph for 1800 cu ft of Denver cells; or 0.05 tons per cu ft of cell. At Kimberly 7.75 tph for 600 cu ft of cell gives 0.013 ton per cu ft of cell. At Bessie 14 tph for 800 cu ft of cell gives 0.017 tons per cu ft of cell. It would be appreciated if the author would comment on what he feels is the upper size limit of particle to attain most efficient utilization of the flotation process. The dewatering screw is a very interesting development since it offers a simple way to prepare coal sludge for more complete clewatering by drainage or mechanical dewatering on screen or filters. In other words it could be used to accomplish the same thing as a thickener tank. I would appreciate having the author's comment on how he thinks such a screw dewaterer would work on a froth.* The process as used in floating coal at the Bessie and Kimberly plants may be referred to as more of a bulk oil float in contrast to a froth flotation process. Experiments on increasing capacity of cells is most interesting since we are going through such an experi- mental period at the present time. Recently a double overflow was installed on our No. 30 Denver cells. So far results are not conclusive. In reviewing this paper the following comments are made pertaining to investigation of methods for increasing capacity: Supercharging: Supercharged air in matte flotation or for that matter the use of the normal amount of air drawn in by the impeller would in all probability cause such an aeration in the cell as to destroy the buoyant effect given to the coal particles by the excessive amount of kerosine used. In other words, air creates an agitation zone throughout the cell, creating a boiling and thereby giving a lower recovery in the cell. It would be interesting to know whether the 7 pct increase in recovery was with no air being admitted to the stand pipe. Changing Impeller Speed: The speed of a receded disc impeller for a No. 30 cell as recommended by the Denver Equipment Co. is, I believe, approximately 250 rpm. At this speed and using supercharged air in excess of 8-oz pressure, we have observed a boiling action in the cells. In our flotation we endeavor to obtain some degree of froth flotation using pine oil as a frother. The boiling action as caused by increasing the amount of air added to the cells is detrimental to recovery in froth flotation. It is our belief that to obtain increased recovery from a cell in froth flotation, additional air must be introduced but at the same time this air must be dispersed throughout the pulp in the form of small bubbles and this can only be done by increasing the speed of the impeller. Therefore, if Mr. Schiffman decreased the speed of the No. 30 impellers and at the same time continued to use supercharged air, the boiling action may have been increased because larger bubbles developed. The lower recovery as reported could be due to this factor. Decreasing the impeller speed will definitely decrease the power consumed but may have other disadvantages. First, we believe it will permit "sanding" in the cell and this in our opinion will increase the wear on the impeller and diffuser, especially so, if there is pyrite and/or sand present in the feed. "Sanding" in the cell when air is used, as in froth flotation, will effect the dispersion of this air and cause boiling.

Jan 1, 1951

By L. E. Shiffman

W. J. Parton—Those operators faced with the problem of treating fine coal whether in bituminous or anthracite will find this paper most timely. I would like to take this opportunity of discussing Mr. Schiffman's paper and at the same time express certain views relating to our Tamaqua plant. I would like to ask the author what type of impeller and diffuser is used in the Denver cells? Screen analysis of products from individual cells indicate that coarser material resists flotation and only floats after greater retention time in the last few cells. Also, the need for a scavenger screen to reclaim non-floated coal particles further stresses this point. I have always felt that more efficient means of cleaning coal between 10-mesh and 28-mesh existed than flotation. Reagent and power costs are high for the flotation process. When floating +28-mesh particles, cell capacity is lowered and some of the particles are lost with the refuse. The Tamaqua plant of the Lehigh Navigation Coal Co. floats —28-mesh coal and capacity of recoverable coal is 40 tph for 1800 cu ft of Denver cells; or 0.05 tons per cu ft of cell. At Kimberly 7.75 tph for 600 cu ft of cell gives 0.013 ton per cu ft of cell. At Bessie 14 tph for 800 cu ft of cell gives 0.017 tons per cu ft of cell. It would be appreciated if the author would comment on what he feels is the upper size limit of particle to attain most efficient utilization of the flotation process. The dewatering screw is a very interesting development since it offers a simple way to prepare coal sludge for more complete clewatering by drainage or mechanical dewatering on screen or filters. In other words it could be used to accomplish the same thing as a thickener tank. I would appreciate having the author's comment on how he thinks such a screw dewaterer would work on a froth.* The process as used in floating coal at the Bessie and Kimberly plants may be referred to as more of a bulk oil float in contrast to a froth flotation process. Experiments on increasing capacity of cells is most interesting since we are going through such an experi- mental period at the present time. Recently a double overflow was installed on our No. 30 Denver cells. So far results are not conclusive. In reviewing this paper the following comments are made pertaining to investigation of methods for increasing capacity: Supercharging: Supercharged air in matte flotation or for that matter the use of the normal amount of air drawn in by the impeller would in all probability cause such an aeration in the cell as to destroy the buoyant effect given to the coal particles by the excessive amount of kerosine used. In other words, air creates an agitation zone throughout the cell, creating a boiling and thereby giving a lower recovery in the cell. It would be interesting to know whether the 7 pct increase in recovery was with no air being admitted to the stand pipe. Changing Impeller Speed: The speed of a receded disc impeller for a No. 30 cell as recommended by the Denver Equipment Co. is, I believe, approximately 250 rpm. At this speed and using supercharged air in excess of 8-oz pressure, we have observed a boiling action in the cells. In our flotation we endeavor to obtain some degree of froth flotation using pine oil as a frother. The boiling action as caused by increasing the amount of air added to the cells is detrimental to recovery in froth flotation. It is our belief that to obtain increased recovery from a cell in froth flotation, additional air must be introduced but at the same time this air must be dispersed throughout the pulp in the form of small bubbles and this can only be done by increasing the speed of the impeller. Therefore, if Mr. Schiffman decreased the speed of the No. 30 impellers and at the same time continued to use supercharged air, the boiling action may have been increased because larger bubbles developed. The lower recovery as reported could be due to this factor. Decreasing the impeller speed will definitely decrease the power consumed but may have other disadvantages. First, we believe it will permit "sanding" in the cell and this in our opinion will increase the wear on the impeller and diffuser, especially so, if there is pyrite and/or sand present in the feed. "Sanding" in the cell when air is used, as in froth flotation, will effect the dispersion of this air and cause boiling.

Jan 1, 1951

By AIME AIME

ON THE occasion of the eightieth birthday of Captain Robert W. Hunt, the Iron and Steel Committee of the Institute, desiring to commemorate the great contributions made to the steel industry by Captain Hunt during his long career, conceived the idea of a Hunt Medal to be awarded annually by the Institute for meritorious contributions to the art of making steel. The project was received enthusiastically by all to whom it was proposed, especially by Captain Hunt's partners and employees who considered it their right, and asked for the privilege of -. - raising the necessary funds within their own circle. This was agreed to, and the Institute has received from them $7500 as an endowment fund to provide an annual award, and $1000 for the expenses of providing of medal.

Jan 1, 1920

Briefly, an open stope is one in which the ore is taken out and no filling is put in; the only support for the walls may be posts or pillars of ore. Such a method is limited to orebodies with strong walls and ore strong enough to stand unsupported over the back of the stope. Details vary and depend on the dip of the vein, mode of breaking ground, method of handling broken ore, and so forth. The examples given are the Beat-son, Birmingham district, Mineville district, and Cornucopia.

Jan 1, 1925

By J. D. Defilippi, E. M. Gilbert, K. G. Brickner

FCC chromium-manganese-nitrogen (Cr-Mn-N) steels differ from most other fcc materials in that these steels undergo a ductile-to-brittle transition. Transformation to martensite is considered to be responsible for this behavior in some metastable Cr-Mn-N steels. However, very stable Cr-Mn-N steels also exhibit a ductile-to-brittle transition. The results of this study indicate that deformation faulting is the probable cause of the brittle behavior of stable Cr-Mn-N steels. Deformation faulting accounts for the ductile behavior of these steels in a tension test at -320°F and brittle behavior in an impact test at -320°F. Deformation faulting also accounts for the toPological features observed on the fracture surfaces of impact specimens of these steels. FACE- centered- cubic chromium-manganese-nitrogen (Cr-Mn-N) steels differ from most other fcc materials in that these steels undergo a ductile-to-brittle transition. Many Cr-Mn-N steels transform to martensite during deformation,l-5 and several investigatorsl-3 have suggested that the brittle behavior of these steels is caused by martensite formation. However, very stable Cr-Mn-N steels also exhibit brittle behavior. Schaller and Zackeyl reported that a very stable Cr-Mn-N steel (less than 3 pct martensite formed at -320°F) exhibited a transition temperature higher than that for steels in which large volume fractions of martensite formed during testing. The explanation given by Schaller and Zackey for this observation was that in the very stable steel the martensite, because of its higher interstitial content, was more brittle than that formed in their other steels. This explanation was questioned by Tisinai and samans4 and Baldwin.6 Moreover, because the toughness of stainless martensite at cryogenic temperatures is generally very low, this explanation does not account for Thompson's7 observation that small additions of nickel (1 to 3 pct) greatly improve the toughness of high nitrogen (0.35 pct) Cr-Mn-N steels. The present paper summarizes the results of an investigation of the low-temperature brittleness in very stable Cr-Mn-N steels. The importance of the mode of deformation on the toughness of these steels is discussed. Table I. Compositions of the Steels Invertigated, Pet Steel C Mn P S Si Ni Cr N - A 0.09 14.70 0.018 0.011 0.47 0.22 18.40 0.54 B 0.12 14.90 0.001 0.008 0.48 0.14 17.80 0.38 C 0.12 14.95 0.004 0.005 0.62 3.95 18.43 0.38 MATERIALS AND EXPERIMENTAL WORK The compositions of the steels investigated are shown in Table I. Steels A and B had compositions within the limits of a proprietary Cr-Mn-N stainless steel,* whereas Steel C was similar in composition to the proprietary steel except for its 3.95 pct Ni content. All steels were hot-rolled to 1/2-in. thick plate. The plates were subsequently annealed for 1 hr at 2000°F and water-quenched. Standard longitudinal and transverse Charpy V-notch impact specimens were machined from the annealed plates. Duplicate longitudinal and transverse impact specimens were tested at 212", 80°, 32", 0°, -100°,-160°,-200°,-256", and -320°F. Longitudinal tension-test specimens were also machined from the plates and tested at a crosshead speed of 0.05 in. per min at the aforementioned temperatures. The fractured impact and tension-test specimens of all three steels were examined to determine whether martensite had formed during testing. Magnetic, X-ray, electron-diffraction, and electron-microscopy techniques were used to detect the presence of martensite in the highly deformed areas of these specimens. Metallographic examination of highly deformed areas of impact and tension-test specimens revealed the presence of dark-etching bands, such as those shown in Fig. 1. These bands were observed only in deformed samples and were thought to be associated with the low-temperature brittleness of the Cr-Mn-N steels. Accordingly, a sample 1 in. wide by 3 in. long was cut from the 1/2-in.-thick plate of Steel C. This sample was surface-ground to a in. and then cold-rolled 60 pct at -320°F. Thin foils were prepared from the cold-rolled sample and examined in a JEM electron microscope. Brightfield, dark-field, and selected-area diffraction techniques were used to determine the cause of the dark-etching bands. Fractographic experiments were also performed. Impact specimens Of Steels A, B, and C were broken at -320oF, and the fracture surfaces of these specimens were immediately shadowed with carbon. The carbon replicas were examined in a Siemens electron microscope, and attempts were made to correlate the topological features of the fracture surfaces with the deformation mechanisms that could be occurring during an impact test of these steels.

Jan 1, 1970

By C. A. WARNER

AN OIL and gas mining lease contract, as entered A into by and between 'the lessor and the lessee, contains certain express covenants stipulating, in part at least, the exact performance thereof; it also contains certain implied covenants, among which may be included that of protection of the leased premises against drainage by the drilling of necessary offset wells. In the drilling for, and production of, oil and gas, however, it not infrequently happens that the lessee, acting in good faith, does not deem it prudent to, drill a test thereon even though the location for such test is offset by a producing well on an adjoining lease. Such conclusion, on the part of the lessee, is generally construed by the lessor as constituting a breach of the implied covenant mentioned above, and he may take proper action to secure satisfaction therefor. The action against the lessee is generally for cancellation or relinquishment of the lease, together with, or apart from, claims for damages allegedly sustained through failure to properly protect against drainage of the leased premises.

Jan 1, 1931

By H. A. BURK

THE ores of the Tonopah, district are hard, compact and' highly siliceous. They contain from .1 to 2, per cent. of sulfide material, of which argentite is the valuable mineral; occasionally pyrargyrite is found in the richer ore. The sulfide is, chiefly pyrite with small amounts of chalcopyrite,. and sometimes sphalerite. The ore also contains a small amount of gold-about 1 per cent. by weight of the silver present. The major gangue constituent is quartz but frequently considerable rhodonite-called by the miners pink manganese-is present. For primary crushing, jaw and gyratory crushers are used. These crushers are of such capacity that, in most cases, one 8-hr. shift will supply the mill for 24 hr. The Extension Co., at the Victor ore house, passes the ore through a 13 by. 24-in. Blake type McFarland crusher set at 13 in., and at the No. 29 re house, a 14 by 24-in. Blake type Traylor crusher is used. The ore is thus crushed to stamping size in one reduction. The capacity of each crusher is about 40 tons per hr.; the power consumption is 0.6 kw. per ton.

Jan 1, 1921

By George F. Becker

A Nere record of Emmons's professional career would very inadequately represent the man. That he was eminent mc know, and our successors will realize in due time; but they must depend upon us for knowledge of a singularly ~vholesome, modest, unselfish personality, and of a character that did honor to a profession in which trustworthiness is indispensable. Those members of the Institute who met Emmons are his friends, and I never knew .one of these who was not the better for that friendship. Emmons was born in Boston, Mar. 29, 1841, the son of Xathaniel H. and Elizabeth (Wales) Emmons, and was named Samuel Frankliri after an ancestor who was of the sarne family as Benjamin Franklin. He took the degrcc of Bachelor of Arts at Harvard in 1861, and soon afterwards went abroad to complete his education. From 1862 to 1864 he attended the courses at the fieole Impkriale des Mines at Paris, Elie de Beaumont arid Daubrke being among his professors. The year 1864-1865 he spent at Freiberg under Cotta and other famous teachers; after which he spent another year in traveling through Europe. Like many other renowned geologists, he approached his ultimate profession from its economic side, and was thus from the first imbued with a sense of high responsibility in the promulgation of scientific opinions or conclusions. With hypotheses which were interesting merely because they were ingenious or even plausible, he would have nothing to do. In 1867 he joined the Geological Exploration of the Fortieth Parallel at its organization under Clarence King, serving at first as a volunteer, but soon receiving a regular appointment. This expedition was the first one of purely geological character sent out by the United States government. As Emmons has shown in his admirable presidential address on " The Geology of Government Explorations," its work was founded on a com-

Jan 1, 1912

By G. C. RIDDELL

THE metallurgist, chemist, and physicist are blazing trails that lead far afield. Pushing on into an "Alloy Age" they see a non-ferrous era over- taking iron and steel. Delving into the nature of the physical world, they break down a supposedly indivisible element, hydrogen. Not content with terrestrial problems, they peer back along the cosmic ray into iaterstellar space, glimpsing forces that are, apparently, still busy with the task of atom-making. Mastering and organizing the material and physical, they advance steadily toward that borderland of science where the concept of matter itself seems abandoned, and force is the substance left.

Jan 1, 1930

By DR. RICHARD RATHBUN

(Washington Meeting, May, 1965.) THE remarks of Dr. Rathbun in his address of welcome render it unnecessary that I dwell either upon the history or aims of the National Museum, and enable me to proceed at once with a brief descriptive outline of the Department for which I am responsible, and this with particular reference to that division devoted to applied geology. The amount of geological material brought together prior to 1876, under the various Congressional acts quoted, was, though valuable, comparatively small. It consisted mainly of the collections made by Professor J. D. Dana and his assistants during the Wilkes Exploring Expedition; by the various geologists accompanying the surveys of the Pacific railroads in 1854-55; the Surveys West of the 100th Meridian under the direction of the Engineering Corps of the Army; the United States geological surveys under direction of Dr. F. V. Hayden ; and the various Land Office surveys. Prior to 1873 there were no paid assistants to care for these collections. They were studied, if studied at all, by " collabrators," so-called, several of whom had offices and even sleeping apartments in the Smithsonian Institution. In the list of these collaborators are found such names as Conrad, Cope, Gabb, Leidy, Lesquereux, Meek, and Newberry. The building now occupied by the National Museum was designed primarily to make room for the great mass of material secured in 1876 at the close of the Centennial Exposition in Philadelphia. As completed in 1880, it afforded opportunity for expansion and incidental organization on much more practical basis than had previously existed. This found expression in the creation of numerous departments with salaried officials to take charge of the various collections. With the appointment of Dr. George W. Hawes to the position of Curator of Geology and Mineralogy, in 1881, and Dr.

Jul 1, 1905

By W. Geo. Waring

THE growing need of better methods for the recovery of zinc and other elements from complex sulfide ores has suggested an inquiry respecting a possible group separation of the elements by the aid of volatilization at more or less elevated temperatures. It 'is evident that if the zinc content of such ores can be completely separated, for instance, as pure oxide, by a volatilization 'method, there should be no difficulty in recovering the other elements by smelting and refining. Zinc burning" as applied to zinkiferous ores has advanced but little in practice since the invention of the wetherill grate-furnace process in 1852, as may be seen by reference to papers on the subject.' In other words the thermochemical reaction employed in effecting the volatilization of the zinc is essentially one of reduction by means of carbon, whether the ores treated contain their zinc in an oxidized form, or as the sulfide. The zinc vapors, liberated from the ores at a temperature above that required for the reduction of ZnO by C (about ,1100° C.) or for the volatilization of ZnS per se, (about' 1300°-1400° C.) are subsequently burned to ZnO or to ZnO + SOz, by contact with' atmospheric ,oxygen in the upper or posterior parts of the furnace chamber, or in a so-called "combustion chamber" after leaving the .furnace proper.

Jan 1, 1925

By Leslie C. Richards

The competitive position of producers of industrial minerals depends upon the delivered price of their product. Freight charges are a major factor in the sales to consumers. A comparison of freight rates on movements of limestone and silica rock in the Pacific Northwest shows a wide variance in mills per ton mile for like hauls, thereby favoring some localities over others.

Jan 1, 1950

By Arnold Hoffman

A RESPONSIBLE steel executive recently declared that scrap shortages, despite fantastic prices reaching up to $50 per ton, are responsible for the loss of 140,000 tons of steel a month and that in March 1947 alone 25 more steel furnaces could have been operating were it not for scrap scarcities. His answer to this serious situation was to ask for a speedier flow of scrap and also abolition of Government control over pig iron distribution. It would be more logical, perhaps, if an answer to this growing problem of scrap deficiency were sought within the steel industry itself. As long ago as 1933, L. B. Lindemuth, a consulting steel metallurgist, warned the steel industry that a shortage of scrap was inevitable and that beyond 1938, adequate supplies for open-hearth furnaces could not be expected. The outbreak of war, with consequent phenomenal demands on the industry, accelerated production of steel and further worsened the scrap situation. Today we are suffering from a condition which could have been prevented had the industry been more far-seeing and provided for an inevitable contingency. However, better late than never, and measures can now be taken to alleviate permanently scrap shortages in the future. This can be done by greater utilization of heavy sinter which experience proved is an excellent substitute for scrao and lump ore.

Jan 1, 1947

By S. F. Emmons

Br far the greater number of the members of this Institute are men who are engaged in the strenuous work of the technical part of their profession, and find little time for the abstract scientific work which is less distinctly practical and pecuniarily emunerative. There is, however, a small but increasingly numerous class whose members devote themselves to broad geological problems which underlie the systematic development, and whose work, theoretically, ought to precede and form a basis of that of their more practical brethren. These are the so-called mining or economic geologists, who are, for the most part, connected with State or National geological surveys. From the character of their work, the life of these men necessarily follows rather different line's than that of most of their colleagues, and is not generally familiar to them. It seems admissible, therefore, that to the life of a prominent member of this class, who died during the past year, having literally sacrified his life to his work, a more extended notice should be given than the relatively small number of his contributions to the Transactions might seem to justify. George Romans Eldridge, son of Ellery and Sarah (Mathews) Eldridge, was born on Cape Cod at Yarmouth, Mass., Christmas day, 1854. His boyhood education in the public school at Yarmouth was followed by a six years' course in the Public Latin School at Boston, from which lie entered Harvard Uni¬versity in 1872, being graduated with the highest rank in his class in the natural sciences in 1876. During his college course he spent the summers of 1875-6 at Cumberland Gap, Ky., as volunteer aid to Prof. N. S. Shaler, who was then in charge of the State Geological Survey of Ken¬tucky. This vacation work, undertaken by him rather as a pastime, gave him his first leaning toward geology. Soon

Mar 1, 1906

By L. J. Kashar

By means of a continuum-mechanics approach, the following equation for calculuting the pressure for axisymmetric cold forging has been derived: where P is the extrusion pressure; K and n are the strength coefficient and the strain-hardening exponent of the steel, respectively; a and b are strain factors, primarily dependent on the die design; and R is the extrusion ratio. Data from compression and backward-extrusion tests performed at a crosshead speed of 0.5 in. per min on a nonwork-hardening material pure lead) and on a work-hardening material (1018 steel) indicate that the predicted extrusion pressures obtained from the derived equation agree very closely with the actual extrusion pressures. Therefore, the equation can be used to predict backward-extrusion pressures from standard mechanical-test data. The decision to cold-forge a part is based on several considerations, most of them related to economics. However, the production feasibility is usually determined by the pressure needed to extrude the part and the availability of tooling that can repeatedly sustain this pressure for over several hundred thousand cycles. A major contribution to the cold forging of steel would result from the development of steels that could be forged at reduced pressures and from the development of techniques that permit the accurate prediction of the pressure necessary to cold-forge the part. The ability to predict extrusion pressures is necessary to properly design the tooling required for the cold-forging process. Attempts to theoretically predict the cold-forging pressure, especially for work-hardening materials, have been unsuccessful in previous investigations of the cold-forging process.1-3 Many empirical relations have, therefore, been proposed relating the extrusion pressure to the chemical composition,' the extrusion ratio,2 the tensile strength,273 and hard- ness, 2 and the yield strength3 of the material being extruded. However, these empirical relations are valid only for the specific conditions used in their development, and, in some cases, the empirical relations had a scatter band greater than * 10 pct. A study of the extrusion process was undertaken with the objective of developing predictor equations for extrusion pressure by using a continuum-mechanics approach to the problem of metal flow. The derivation of such an equation is summarized in this paper, and data are presented that confirm the validity of the derived equation. DERIVATION OF THE EXTRUSION EQUATION If the extrusion of a material through a die is considered in terms of a work balance, it has been shown that it is possible to derive an equation relating the work necessary to move the material through the die to the deformation work undergone by the material. The work done, W, in moving the material is given by where F is the extrusion force, I, is the distance the material was moved, A, is the original cross-sectional area of the material, P is the extrusion pressure acting on A,, Ap is the cross-sectional area of the extrusion punch, and Pp is the punch pressure acting on Ap. The deformation work, WD, is given by where V is the volume of metal deformed, ay is the flow stress of the metal, and E is the total strain undergone in the extrusion. If there are no frictional losses, the work done, W, is equal to the deformation work, WD; therefore, Since the volume of a metal does not change during deformation,

Jan 1, 1968

By C. M. Tucker, Kent R. Van Horn, W. P. Sykes

RECENT investigations of the molybdenum-carbon alloys have been reported by Becker and Ebert1‡, Westgren and Phragmén2, T. Takei3, and H. Tutiya4. Takei3 studied the Mo-C system by employing metallographic and X-ray methods, and the other publications described the determination of the crystal structure of the molybdenum carbides. In exploring this system by a technique previously applied to the tungsten-carbon series5, the results of Takei were confirmed with two definite exceptions; i.e., first the composition of the eutectic, and second the nature of the carbon-fish intermediate phase. Consequently, a more thorough examination of the molybdenum-carbon constitution was initiated in an effort to correlate the data supplied by the microstructures, diffraction patterns and chemical analyses. METALLOGRAPHIC INVESTIGATION A briquette of molybdenum powder when heated in a carburizing atmosphere at 1500° to 1600° C. for several hours develops the carbon-rich layer shown in Fig. 1. The carburization was accomplished by placing the briquette in a carbon tube, which was heated in the hydrogen atmosphere of an alundum muffle wound with tungsten resistor. While the macrostructure indicates two distinct shells, and suggests the possibility of two carbon-rich phases, no evidence of this condition could be detected by the microscope, which revealed but one high-carbon constituent. This carbide forms next to the molybdenum as a relatively

Jan 1, 1935

By L. D. HUNTOON

MY first article on Canadian Gold, published in the Canadian Mining Magazine in 1911 expressed the view that the Hollinger mine would repay all the money invested and that other mines would be developed in this area. Many published forecasts have since been made. Quoting from the Northern Miner of Oct. 29, 1931: "It will be noted in studying the chart prepared by this engineer that his forecast for 1931 at $50,000,000 was too modest, as the output for this country this year will be closer to $54,000,000."

Jan 1, 1932