Search Documents

By M. Cornelius

Drilled shaft construction through caving soils has historically been an uncertain, risky and costly operation. Uncertain, because the zone of caving may or may not be known, risky because the loss of a shaft is disastrous, and costly because the Contractor, who faces these risks, must include large sums of money in his bid for shaft wall stabilization techniques. This case study will discuss the stabilization techniques that are typically used within the United States, and then present new technologies, born in Europe, that are being utilized in the States by Malcolm Drilling Company today.

Jan 1, 1999

By R. W. Stahl

The use of continuous mining machines has greatly minimized the necessity for blasting in coal mines, even during pillar recovery; however, explosives are still used to blast stumps. The use of improper blasting materials, improper procedures, or both has caused mine explosions and fires, with loss of life and property damage. Researchers and manufacturers are continuously improving explosives and blasting accessories; use of the more recently developed materials will make the blasting operation safer. Extreme caution is mandatory when blasting stumps, as the ignition of methane or coal dust may trigger an explosion or cause a fire. Since the blasting of stumps will no doubt continue, although often unnecessarily, this paper summarizes recent findings published by the Bureau of Mines and recommends safer methods.

Jan 1, 1962

By R. L. Balmer

This information circular, which describes the methods and costs of sinking a small underground shaft with steel supports at the Keystone mine of American Smelting and Refining Co., near Crested Butte, Colo., is one of a series being prepared by the Bureau of Mines on current shaft-sinking practices in various mining districts of the United States. Preparations for sinking a combined exploration, development, and production shaft from the lowest level of the Keystone mine began early in 1957. This vertical, three-compartment, 6-1/4-by 16-foot rectangular shaft was to be sunk in separate stages or lifts so as to correspond with the progress of an associated lateral exploration and development program. The first section of the shaft was collared and sunk to a depth of 209 feet between September 1957 and April 1958. Because of the depressed base-metal market, the mine was shut down as soon as the initial phase of the exploration and development program had been completed and before any deeper sinking could be attempted.

Jan 1, 1962

By B. S. Terry, C. L. Harris

After measuring the kinetics of Ni reduction from a SiO2-saturated fayalite slag into a Cu-based metallic phase on a laboratory scale, a general model was developed that is capable of simulating mass transfer to and from metal-slag, slag-gas and metal-gas interfaces for multiple species. The model was used to simulate the reactions that occur when Cu and Ni are reduced from fayalite-based slags into a Cu-based metallic phase. Good agreement was achieved between model predictions and experimental data

Aug 1, 1995

By C. Birch

"A ‘geologically constrained’ orebody model has long been hailed as vital for a Mineral Resource statement that is compliant with the South African Code for Reporting of Exploration Results, Mineral Resources and Mineral Reserves (SAMREC Code). In this paper, the requirements for geological modelling as contained in the outline for the SAMREC Code are considered, and whether the new modelling software available on the market is a ‘black box’ or is better for modelling than traditional methods of wireframe creation.Implicit geological modelling is a technique that uses a radial basis function to establish and update geological models relatively quickly and efficiently from borehole data, outcrop data, manually interpreted vertical or horizontal sections, and structural data. Assays and any coded drill-hole data, such as lithology and alteration, can be interpolated.Leapfrog Geo software is an example of this new approach to geological modelling. A case study of a short training course in geological modelling for non-geologists at the University of Witwatersrand, as part of the Higher Certificate in Mineral Resource Management, is presented. The benefits of this type of geological modelling software are considered for this type of assignment as well as for mining industry applications.The use of geological models in mine planning is reviewed and a case study is presented comparing the variations in mine plan design and financial output of 13 final-year Mine Design projects from the University of the Witwatersrand School of Mining Engineering. These designs were all based on the same geological model created in the traditional way, and yet the resultant mine designs were significantly different, with very different resulting financial outlooks for the project. This raises questions as to how significant a very detailed model in the pre-feasibility and feasibility phases of projects really is, considering the huge costs involved in gathering the required data to build a SAMREC-compliant geological model."

Jan 1, 2014

By E. G. King

An earlier Bureau of Mines report4 provided low-temperature heat-capacity and entropy data for three sodium vanadates. This report continues the study of vanadates by presenting analogous data for three crystalline calcium vanadates - calcium metavanadate (CaV206), calcium pyrovanadate (Ca2V2O7), and calcium orthovanadate (Ca3V208). No similar data for these compounds have been published previously. MATERIALS All three vanadate samples were prepared by the Bureau of Mines by heating stoichiometric mixtures of reagent-grade calcium carbonate and vanadium pentoxide.5 Calcium metavanadate was prepared at 610° to 660° C. A stoichiometric mixture was heated for 17 days with intervening grindings, mixings, and adjustments of composition, as shown necessary by chemical analysis. The final analysis gave calcium oxide, 23.48 pct. (theoretical, 23.57 pct.) and vanadium pentoxide, 76.32 pct. (theoretical, 76.43 pct.). The sample also contained 0.11 pct. acid-insoluble matter. The X-ray diffracton pattern showed no lines of free calcium or vanadium oxides. No X-ray diffraction patterns were found in the literature for any of these substances.

Jan 1, 1961

Evaluation of the Iron Blast Furnace Process using Heat and Material Balances of the Flame-Zone

Sep 13, 2010

By R. R. Faddick

Properties of coal-water slurries were studied in two separate phases: a rheological phase and a pipeline phase. The purpose of the study was to investigate the rheology of fine coal slurries to determine the effect of fine particles in a coal-water mixture on the economic and operational aspects of a slurry pipeline. The slurries consisted of 6x10, 100x200, and 200x0 mesh coal in water. A fourth slurry consisted of a mixture of the 6x10 and 200x0 mesh coal. Brookfield and Stormer rotational viscometers were used to obtain or simulate rheograms for a range of fine coal concentrations, temperatures, and particle sizes. All the slurries were pumped through a 1-inch diameter acrylic pipe. The fine coal slurries were found to encompass four distinct rheological models. The narrow size distribution of the coal slurries was apparently responsible for the high pipewall friction losses, more so than the particle size. A scale-up method applicable to Bingham plastics was found satisfactory for predicting pipeline headlosses of fine coal slurries from rheology data.

Jan 1, 1974

By Glen A. White

The level of impact and mitigating measures that are forecast in an environmental assessment (EA) for a new, or significantly modified, metallurgical processing facility or mine are taking on increasing importance during the subsequent life of the facility. The basic premise is that one is authorized to operate within the envelope defined by the approved EA. Operations inevitably change as they develop and mature, and at some point, one is faced with the prospect of re-doing the original EA work. This can lead to significant development delays. Cameco Corporation (Cameco) has played a major role in developing the northern Saskatchewan uranium mining industry over the past decade. Through the EA process, the company has developed ideas on what works well in generating approvals that give the operator some future flexibility. Early introduction of concepts for potentially different mining and processing methods, as well as contingency plans if things do not work out exactly as predicted in the original EA, can make subsequent regulatory approval for change a more efficient process. One must also preserve the principles of open consultation upon which the EA process was originally based. As such, involvement and support from local communities and other stakeholders is required to ensure the long-term success of the EA process.

May 1, 2004

By Emmanuel N. Zevgolis Ismene-Polyxeni Kostika

Keywords: reduction, kinetics, laterites, rotary kiln, dust In this work, the reduction kinetics of dust from nickeliferous Greek laterites is investigated. The dust is a by-product from laterite treatment in rotary kilns and it comes from washing towers, electrostatic filters and polycyclones. Laboratory made pellets from this dust were also examined. Reducibility was studied in the temperature range of 700°C to 850°C in a laboratory tube furnace. Kinetic analysis of the results showed that at lower temperature values the mixed kinetic model verifies the experimental results of dust and pellet samples. At higher temperatures (800° and 850°C) diffusion becomes the rate controlling mechanism. The calculated activation energy values verify also the above mentioned results.

Jan 1, 2005

By D Craw

Oceana Gold as part of their environmental strategy are looking at various methods for cost-effective revegetation of their tailings dams. Under the concept of revegetating the tailings this study looked at several issues. These issues were; testing different methods of revegetation, arsenic (As) uptake in vegetation with respect to capping thickness, and background As levels in farmland areas above mineralised rocks. A number of plots were set up in a temporarily disused tailings dam to trial the direct sowing of ryecorn into the tailings.   Ryecorn was sown in sandy tailings (ca 1000 mg/kg As) and then covered with oxidised schist to anchor the seeds. This proved successful and ryecorn was established. Once the plots covered with oxidised schist were growing, 1 m and 2 m strips were sown on the sheltered side of the existing plots without the covering of oxidised schist. The uncovered plots also established successfully. From this set of trials a sowing plan can be developed that uses a minimum of resources to successfully establish vegetation. The maximum As content of the ryecorn was 80 mg/kg. Clover, Yorkshire fog and ryegrass plant matter was sampled from a pot trial that used different thicknesses of topsoil covering tailings material. As the thickness of topsoil increased, the amount of As taken up decreased. Soil samples were taken from farmland areas which were known to have elevated levels of As (up to 1000 mg/kg) in the top 10 cm. Vegetation samples were also taken from the same locations, and show the As levels in plants is <50 mg/kg.

Jan 1, 2006

In mining industries, materials loading and handling costs represent a significant component of the total (capital and operation) costs. A variety of methods have been applied in surface mine equipment selection in order to select the suitable loading and haulage system with the lowest total cost. The optimal size and number of equipment calculation are very important task for mining engineering because loading and haulage equipment are major proportion of open pit mining cost. Capital and operating cost are considered in objective function with respect to interest rate, insurance and tax in non-linear form. Shovel and truck annual productivity constraint, fleet matching constraint and number of truck per shovel constraint are incorporated in this optimisation problem with continuous variables. This formulation will yield total cost minimisation per hour and good accuracy compared to previous methods.

Dec 6, 2010

By E. R. Maize

[In report of Investigations 3452,5/ baling with roof movement in the Crucible mine, reference was made do to the fact tart timber decay was being studied at the time of writing. This roper, written after completion of that study, describes s the work and summarizes the data obtained. When the study of roof movement as begun at Crucible two ideas were advanced on decay Of timber by some of the officials: (1) That timber decay vas unusually rapid in the Crucible mine, and (2) that timber coated with rock dust decayed more rapidly than those teat were not so coated. There yore no records by which these ideas could be tested, and it appeared wise to make a limited; investigation particularly of the effect of rock dusting on decay, as rock dusting is an important means of preventing coal-dust explosions.]

Jan 1, 1940

The extraction of minerals and coal at greater depth, employing higher-powered machinery to improve production levels, imposes an increased burden on the ability of a ventilation system to maintain an acceptable mine climate. Hence, mechanical mine cooling systems are often adopted, which can be expensive in terms of both their associated capital and operating costs. Consequently, in order to optimize the total mining costs, it is essential to provide the mine operator with a method with which to determine the most cost effective and efficient mine cooling system. In a previous paper1a novel energy analysis employing the concept of exergy was proposed and applied to cooling systems applied to two conceptual model mines, representative of UK deep coal operations, and their resultant subsurface thermal environ-mental conditions predicted. This paper presents an analysis of the results obtained from the application of this novel technique to assess the performance of various cooling systems applied to a current UK colliery that is experiencing climatic problems due to its depth and highly mechanized production and development workings. To perform this analysis, ventilation and climatic data collected at the case study mine were used to construct balanced mine ventilation and climatic network models to replicate the subsurface environment. Where air conditions exceeded specified climatic limits within identified climatically control zones, mechanical mine cooling systems were employed. A number of cooling system configurations were applied to these model to investigate the potential to satisfactorily regulate the thermal environment. The heat energy transferred out of the air stream by the various cooling methods was absorbed using a variety of chilled water systems, which were designed to operate at various water flow rates and temperatures. Models of various cooling system were developed and applied to control the underground climate within this mine network to within pre-set climatic limits. The results of a comparative analysis of the energy transfers that were produced by the application of the different cooling systems are presented in the form of exergy performance indices. The results produced by simulation models constructed to represent chilled water distribution networks to supply the various air coolers, are designed and balanced. The results of the exergy analyses applied to the operation of the various chilled water pipe networks are discussed and used to assess the exergetic performance of the application of each proposed cooling system to the mine ventilation network.

Jan 1, 2004

By Noel Dent

The Electrodet@ Electronic Detonation System Wilere are we going with regard to Accurate, Reliable, Easy to Use and Cost Effective Initiation using electronic initiation techniques? Improvements and applications in theJierd

Jan 1, 1995

Milling circuits are known to be difficult to control. In order to address these difficulties, it was decided to develop and test a model predictive controller (MPC) for a milling circuit. A milling simulator was written using Microsoft Visual C++ and used to design and test the MPC controller. Due to the large number of tuning parameters in a controller of this type, an optimizing algorithm was written that automatically tunes the controller. Good, robust control was obtained when the controller was tuned using this algorithm. Control was further improved by combining feedback and feed forward control and by using quadratic programming in the MPC algorithm. The movement of the manipulated variables was reduced by using a novel technique that allows the controlled variable to vary within a specified region around the set point. An optimiser controller was also successfully implemented to control the circuit at its maximum throughput.

Jan 1, 2000

By Leandro Echavarría

El presente texto describe el sistema epitermal de Arcata, situado en Arequipa, Perú. Arcata es un distrito epitermal de sulfuración intermedia rico en plata y metales base, cuya mineralización se hospeda en vetas de rumbo predominante noroeste y movimiento principal paralelo a la inclinación que forman una estructura de fosa (graben). Las vetas poseen texturas de relleno de espacios abiertos como bandeados costriformes, en cucarda, crecimientos en peine y brechas, con ganga de cuarzo, calcita, rodonita y rodocrosita. Por su parte, los minerales de mena más comunes son galena, esfalerita, calcopirita, con los metales preciosos hospedados en sulfosales de plata (pirargirita y tetrahedrita). Asimismo, se ha identificado una compleja secuencia paragenética con varios pulsos responsables de la mineralización económica.

Apr 22, 2003

By K. Adham, C. Lee

Over the last forty years, a number of specific fluidized bed applications in nickel extraction have been developed for commercial use. Five important processes have gained particular acceptance, namely, sulphide ore roasting, nickel sulphide (matte) roasting, nickel oxide reduction, laterite ore pre-reduction, and nickel chloride pyrohydrolysis. These applications involve different feed materials and process conditions, however, all benefit from fast reaction kinetics and high heat and mass transfer rates in the fluidized bed reactors. They have been studied, tested, and implemented by various nickel producers, who have published their results in many papers and patents. This paper examines the design issues surrounding the application of fluidized bed technology to the above nickel processes. Based on the available data in the open literature, computerized process modelling is used to provide generic flowsheets that illustrate the key features of each process.

Jan 1, 2004

The prospect of utilisation of phosphate ores which contain high P2O5 values associated with Al and Fe has produced a great deal of interest over many years. Processing options have generally been based on the utilisation of by-products which were required to offset the processing costs.   This paper presents a range of processing options which have been investigated at laboratory or technical scale on phosphate ores which predominantly consist of crandallite, CaAl3(PO4)2(OH)5.3H2O and millisite, Ca(NaK)Al6(PO4)4(OH)9.3H2O. Christmas Island (Indian Ocean) and Mt Weld (Western Australia) phosphate ores are good examples of such feedstocks. It is expected that these processes may also be applicable to such phosphate ores from other locations.

Jan 1, 1990

By D. Kwietnewski

The 4th bore of the Caldecott Tunnel is a 50-ft horseshoe shaped highway tunnel located in the hills east of Oakland, California. Tunnel excavation was mostly completed using one of the world?s largest commercially available roadheaders, a Wirth T3.20. The geologic profile included seven different geologic units, which displayed a range of different behavior with regard to excavation and initial support. Following a brief introduction to the excavation and support methods, this paper will discuss roadheader performance in the various geologic units encountered during excavation. Comments will also be made concerning the relationship between the roadheader method of excavation and observed ground convergence during excavation.

Feb 27, 2013