Search Documents

By D. Malovichko

Seismic events and pillar failures observed in two platinum mines in the Rustenburg area, South Africa, were investigated. We studied the sources of approximately 300 largest seismic events recorded in 2009. Moment tensors of these events were estimated from amplitudes and polarities of P- and S-waves. The inverted mechanisms contain isotropic implosive components in many instances. Analyses of uncertainty of the moment tensor solutions confirmed the significance of the implosive component in general. Several documented cases of pillar failure were considered in detail. For each of these a seismic moment tensor was calculated from an elastic stress model assuming an instant removal of a failed pillar. The geometries and magnitudes of the theoretical seismic moment tensors are in agreement with the observed (i.e. inverted from seismic data). The results indicate that either pillar failure or fracturing in the proximity of the reef (within a fraction of the dominant wavelength of seismic waves) are responsible for a significant portion of the large events recorded in these mines.

Jan 1, 2012

By James Y. Oldshue

"Very seldom is it possible when contacting a gas with a slurry to measure the dissolved gas concentration in the slurry, and even were it possible, seldom are equilibrium data available with a suitable Henry’s law constant.In general, by assuming a reasonable value for the dissolved gas concentration in the slurry and a corresponding equilibrium gas partial pressure P*, Kga values can be calculated for the pilot plant and scaled up. Then, with the same P* value at various reaction conditions, a mixer can be designed which is quite satisfactory, having a reasonable design factor for full-scale performance.We will take as an example a slurry of a known solids composition and use a continuous 4 tank system. By assuming a percentage saturation of the dissolved gas in the first tank, the dissolved gas concentration can be obtained in the other three tanks. It usually is possible to measure the off-gas composition in each of the 4 tanks. If the top of the tanks is connected in the form of a multi-compartmented horizontal autoclave, then a modified top off-gas composition in each compartment must be used."

Jan 1, 2003

By Lam. E. K., J. W. Jarvi, B. P. Bharadwaj

"The Rabbit Lake Operation is located in Northern Saskatchewan on the western shore of Wollaston Lake approximately 800 km north of Saskatoon, Saskatchewan.The Operation is owned by a joint venture of Cameco Corporation and Uranerz Exploration and Mining Limited. Cameco is the operator.The Mill started production in June 1975 under the ownership of Gulf Minerals Canada Limited and over the past twenty years has increased the rated production capacity to over twice the original design.The Mill was originally designed to process 485,000 tonnes per year of ore with an annual production of 2.0 million kg of U308 (yellowcake). During the past ten years changes in ore sources and process modifications have led to increased milling capacity and production targets. The Mill has treated a total of 8.6 million tonnes of ore and produced over 40 million kg of U308 in the twenty year period, despite the shutdown and cutbacks in operating time since 1989.The 1995 tonnage throughput was 206,000 tonnes per year. Annual production though has risen to 3.6 million kg of yellowcake despite the departure from full-time to half-time operation in 1991 (7 up-7 down). The forecast for the coming years will see tonnage rising from 300,000 to 570,000 tonnes, production of 4.5 to 5.4 million kg of yellowcake and an anticipated return in the year 1998 to full time operation.This paper will give a brief history of the Mill and focus on the present flowsheet and recent improvements to the process."

Jan 1, 1996

Au-Ag Recovery from Complex Ore by Flotation

Sep 13, 2010

By Johan C. van Dyk, Johan W. van Zyl, Martin J. Keyser

"Coal is a crucial feedstock for South Africa’s unique synfuels and petrochemicals from coal industry and it is used as the main feedstock to produce synthesis gas (CO and H2) via the Sasol-Lurgi Fixed Bed Dry Bottom gasification process. Detailed coal characteristics are essential to predict gasification behaviour when a specific coal source is to be gasified.The principle aim of this paper is to highlight and discuss those specific coal characteristics, which affect gasification behaviour and stability.In order to determine the suitability of a coal source for gasification purposes, the coal is characterized and the results compared with historical data. Benchmark data, where it was possible to operate the gasifier with ease and relatively high stability, is used as a reference.Coal sources with extreme properties (i.e. low reactivity, ash content <10% as is used by Dakota Gasification Company, or “brown coal” with moisture >30%) can probably be gasified in a Sasol-Lurgi Fixed Bed Dry Bottom gasifier provided that certain operational changes are implemented. Other properties, like high caking and extreme ash content for example, require blending to acceptable levels."

Jan 1, 2003

By C. Bucknam, M. McComb

Mercury and silver polythiocarbonate sludge that was generated from the pilot testing of optimized mercury removal from cyanidation pregnant eluate solutions prior to Merrill-Crowe recovery of gold and silver were tested for long term stability at Newmont Metallurgical Services. Sludge samples were mixed with heap leach residue to simulate disposal of the sludge in spent or active areas of the heaps and leached for twenty weeks with water and cyanide leaching solution, respectively. Leach testing results are presented as well as analysis of the sludge using scanning electron microscope techniques down to the <1000 nanometer scale.

Jan 1, 2007

By B. J. Barfield

Standard erosion plots (4.6 m by 22.1 m on 9 percent slope) were constructed on the Alston Surface Mine of Peabody Coal Company in Western Kentucky to evaluate the effects of placement technique and density on the erodibility and eroded size distribution from mine spoil and reconstructed topsoil. PLots were constructed with a dozer and scraper pan from shale spoil material, topsoil (A horizon) and subsoil (B and C horizon mixture) using soils stockpiled at the Alston Surface Mine. Plots were evaluated under fallow conditions with a tilled plot surface and two compacted conditions. One compacted condition was generated by tracking the surface with a dozer and rolling with a loaded scraper pan. The second was generated by rolling the surface with a solid wheel compactor. Rainfall was supplied with the Kentucky Rainfall Simulator at a rate of 63.5 mm h-l with the plots in three different soil moisture conditions; dry, field capacity, and very wet. Runoff was evaluated for flow rates, sediment concentrations, and aggregate and primary particle size distributions. Sediment yields and the Universal Soil Loss Equation E130 indexes were calculated from the data for each plot. The erodibility was calculated from the tilled plot data using a weighted soil loss and E130 value from the dry, field capacity and wet runs, and a cover management factor calculated for every other condition. For the topsoil and subsoil plots, sediment yield was greatest for the dozer scraper pan plots and lowest for the tilled plots. For the shale plots, erosion rates from the wheeled compacter plots were the highest and tilled plots the lowest. Average erodibilities were 0.14, 0.38, and 0.41 tons ac h ft-1 tonf-1 in-1 hundred ac-1 for the shale, subsoil, and top-soil plots. Cover management factors for each plot were 1.29, 1.42, and 1.17 for shale, topsoil and subsoil plots compacted with the solid wheeled compacter and 1.29, 3.79, and 2.51 for shale, subsoil, and topsoil plots compacted with the dozer scraper pan conbination. The accuracy of the Wischmeier erodibility nomograph was evaluated on the data collected. Erodibilities were accurately predicted for the topsoil plot and poorly predicted for the sub-soil plot. The accuracy of the CREAMS procedures for predicting the composition (size distribution) of eroded particles was also evaluated. The composition was well predicted for the topsoil plots, moderately well predicted for the shale plots and poorly predicted for the subsoil plots.

Jan 1, 1983

By M. M. Wong

The Bureau of Mines, under a cooperative research program with four lead companies, has investigated a nonsmelting process for the production of lead metal. The process, which would eliminate sulfur dioxide generation and minimize particulate lead emissions, involves ferric chloride leaching of galena concentrate to produce lead chloride, followed by molten-salt electrolysis of the lead chloride to yield lead metal and chlorine. This chlorine is used to regenerate ferric chloride in the leaching solution. The process was tested in an experimental unit with a capacity of 500 lb of lead metal per day. The tests were performed in three 10-day and six 5-day campaigns, during a period spanning 28 mo. The study was carried out using a southeastern Missouri lead concentrate. Typical lead recovery was about 98 pct. Process problems related to impurity buildup and control were studied. When copper and silver impurities were removed from the leaching solution, a lead metal purity of 99.999 pct was obtained. Lead-in-air levels and lead-in-blood levels of operating personnel were monitored. The process has potential for producing lead with minimum pollution, but is not ready for commercial utilization. Operation of a prototype commercial electrolytic cell and a full-scale pilot-plant investigation by industry are needed to evaluate the commercial viability of the process.

Jan 1, 1983

Elongates are commonly used as stope support in South African gold and platinum mines. To evaluate the effect of the inherent strength, stiffness and yield variability associated with elongates, a statistical method is presented which addresses and quantifies the support performance at various levels of certainty. The analysis, which is based on a normal distribution, makes use of force-deformation curves determined from multiple laboratory compression tests on the same support type. The applicability of the method is illustrated making use of actual performance capabilities of various types of elongates. In order to ensure a high probability that support units installed underground exceed the standard support performance curve established by means of laboratory tests, the statistical mean of a suite of tests based on the same support type is downgraded. The ?correction factor? is a function of the mean and standard deviation of the test data, as well as the sample size of units deemed to control the local rock mass stability. It is shown that downgraded performance curves based on a high probability (90 to 95percent) of support units exceeding this performance level are suitable to ensure that the design of support systems will in variably meet the design criteria. In the highly discontinuous hangingwall rock mass typically associated with intermediate- and deep-level mining operations, the interaction between adjacent support units is comparatively limited (at the support spacings commonly used). Therefore, the appropriate sample size (n) of the support units controlling the local rock mass stability should be n= 1. In shallow mining conditions, sample sizes of up to n=5 may be warranted, depending on the spacing of joints and other discontinuities in the hangingwall.

Jan 1, 2001

By J. J. Dekker

Controlling noise has proven difficult in mining, and noise-induced hearing loss (NIHL) remains common. In 2008, a South African Mine Health and Safety Council study focused on small- to medium-sized mines in relation to the milestones set by the industry to prevent NIHL. An evaluation of the compliance of ten diamond, sand, aggregate and Ready mix concrete mines and production sites with standards, legislation and best practice guidelines relating to NIHL prevention was conducted, using a noise compliance audit tool. The findings indicated that all mines surveyed had poor compliance with the international standards, compliance with International Standards Organization standards being the poorest. There was a clear distinction between the small and the medium-sized mines in their compliance with local standards and legislation (ranging from 14 per cent to 66 per cent). The areas of best compliance were audiology and medical examinations. The lower-than-expected compliance was largely attributable to shortcomings in hearing conservation programmes for occupational noise. Initiation of remedial practices in the small- to medium-scale mining sector to facilitate improvements in NIHL prevention and compliance with standards and legislation is recommended. Keywords Hearing conservation, small-to-medium mines.

Jan 1, 2011

By P. H. Mutschler

The Bureau of Mines studied the costs of transporting fossil fuels, coal, and residual fuel oil from areas of production to consumer regions. Transportation data were stratified by type of carrier, size of shipment, and distance to determine what general effects these variables have upon transportation costs. Economics of haul for coal exist for longer versus shorter distances, and for larger versus smaller trainload sizes. Tanker and barge transportation of residual fuel oil does not show economies of haul for longer distances. It is shown that tanker size and seasonal variation are primary factors influencing the cost of shipping. Railroad transportation data show that coal from western coalfields could be competitive with foreign residual fuel oil in selected midwestern fossil fuel markets. However, the western coal would not be competitive in the New England and the eastern seaboard energy markets.

Jan 1, 1973

By S. Sun

The equilibrium distribution of Cu, Fe and Ni between Cu-Ni-Fe mattes and Pt alloy was measured as functions of the sulphur partial pressure (pS2), oxygen partial pressure (pO2),temperature and Fe content of the matte. The distribution ratios of Cu, Fe and Ni between matte and alloy were independent of oxygen pressure when the pS2was fixed at 2.5x10-5atm and pO2was varied between 10-15and 10-12atm. The distribution ratio of Cu, Fe and Ni increased as the sulphur partial pressure increased. The Cu and Ni distribution ratios decreased with increasing temperature and the Fe distribution ratio increased slightly over the temperature range of1350?1500°C. For mattes where the proportions of Cu and Ni were kept constant, the distribution ratio of Cu increased as the Fe content in the matte increased. The Fe and Ni distribution appeared to be independent of the iron content in the matte and had a value of 1.2 and 1.6 respectively. The activity of Cu, Fe, Ni in the matte was calculated using a regular solution model for solid Pt-Fe-Ni-Cu alloy. The activity coefficient of Cu, Fe and Ni decreased as pO2and pS2increased.The activity coefficients also appeared to be independent of the Fe content and temperature over the range of 36 to 54 wt% iron and 1350 to 1500°C respectively. Keywords: activity, alloy, matte, thermodynamics

Jan 1, 2004

This report is in fulfillment of Contract H0230031 awarded to Bituminous Coal Research, Inc., on May 23, 1973. The scope of work to be performed under this contract was divided into four phases: Phase I - Design, Phase II - Construction, Phase III - Field Demonstration, and Phase IV - Analysis and Final Report. During Phase I, an agreement was finalized with the Rochester and Pittsburgh Coal Co. for conducting field tests of the proposed shearer spray systems on a longwall panel in the company&apos;s Jane Mine in Indiana County, Pa. A drum was then designed which could be used on the Eickhoff shearer, Model EW170-L, being used on this longwall and which would utilize the following spray systems: 1. One spray nozzle located in front of each cutter bit with the jet directed at the cutting surface. 2. One spray nozzle located in back of each cutter bit with the jet directed at the back of the bit. 3. Standard Eickhoff nozzles located in a header along the drum scrolls. 4. A fixed header mounted on the shearer directly behind the drum to simulate the spray system originally used on the Eickhoff shearer.

Jan 1, 1976

By Vladimir Admek, Paul W. Jeran, Michael A. Trevits

It has&apos; been found that lithological conditions over the Pittsburgh Coal bed cause the subsidence coefficient to vary within the area of the subsidence trough. This precludes the use of European developed predictive models, which are based upon a constant subsidence coefficient. Regression analysis of the distribution of subsidence coefficients from 11 Bureau of Mines, U.S. Department of the Interior, longwall panel studies on the location relative to the edge of the panel has yielded a third degree polynomial equation. This equation has been incorporated into a BASIC computer program for use on a personal computer that allows users with no previous knowledge of the theory of subsidence to predict vertical movements over typical longwall panels in the Northern Appa1achian Coal Basin.

Jan 1, 1986

By Chas. F. Jackson

The annual reports of the supervising engineers of the seven sections comprising the Mining Division are assembled in the following pages and constitute the annual report of the division. In planning activities, the aim has been to adapt the work to changing conditions and needs of the mining industries and to avoid becoming bound to any particular type of investigation when others are found to be of more pressing interest.

Jan 1, 1939

By R. L. Howell, L. C. Atkinson

Typical sedimentary sequences overlying coal seams consist of interbedded sandstones, siltstones, shales, and rider coal seams. In many surface coalmine settings, these sediments are saturated; and prior dewatering of them is necessary for effective and economic mining, including the stacking of saturated spoils. Such sedimentary sections usually have a very low vertical hydraulic conductivity that does not allow them to drain in a timely manner prior to their being stripped. One potential solution is installation of drainwells. Drainwells are small diameter wells that can collect water laterally from the various more permeable layers in the overburden and then gravity drain it to a lower layer – often the coal seam being mined – where it can be removed by pumping wells or sumps located in the bottom of the pit. A ground-water flow model utilizing the 3-dimensional finite element code MINEDW has been used to evaluate the effectiveness of usingdrainwells in a hydrogeologic setting that is typical of the Powder River Basin. A series of numerical simulations were completed using various combinations and spacings of drainwells and pumping wells to dewater the overburden and coal seams. The numerical simulations suggest that drainwells can be a very effective method of overburden dewatering.

Jan 1, 2000

By Roberto C. G. Oliveira, Scott C. Brown, Brij M. Moudgil

"The wettability or surface energy of particle surfaces dictates a number of multiphase ensemble interactions that have a significant impact in mineral processing. Dispersion, bulk powder handling and flotation are just a few of the processes that are largely influenced by the degree of hydrophillicity or hydrophobicity on particulate surfaces. Because of the importance of surface wettability, a number of simple, precise and accurate techniques for accessing surface wettability or contact angle on macroscopic flat surfaces have been developed. However, these techniques cannot be directly applied to the particulate surfaces that are often in query. Though a number of techniques are available for accessing the wettability of particulate surfaces, these methods are either relative, application specific or prohibitively tedious. In the present study, key features of existing techniques are combined to formulate an improved method to delineate particle wettability that is simple, versatile and capable of providing reproducible measurements in an industrial environment.Through the use of an inert adhesive and an inert macroscopic surface as a support, it is illustrated that precise measurements of particle wettability are obtainable under suboptimal or ‘shop floor’ conditions. The measurement of the maximum external meniscus height formed between a test liquid and a particlecoated rod is employed to estimate phenomenological contact angles on particles ranging form a few nanometers to several hundred microns in size."

Jan 1, 2003

Interest in mining narrow, vein-type ones has increased world-wide during the last few years despite the fact that prices of metals have not risen in proportion as production costs of mining, such as labour and energy. In many mines, where narrow ones are mined, the mining technique and equipment used have been poorly mechanised. The mining methods have been cut-and-fill or shrinkage stoping. Pneumatic jack-legs have been used for drilling and slushers have been used for loading. The methods that have been used can be called the &apos;first-generation&apos; methods. Work has been very hard for miners. It has been dangerous and exhausting. Production volumes of mines, and a s a result of that, also profits have been low.

Jan 1, 1990

By N F. Fraser

Seafield ResourcesÆ offshore placer gold project covers c.10 000 km2 of the Westland continental shelf between Karamea and Jacksons Head, from the low-water mark out to the 120 m isobath (Figure 1). De Beers Marine (DBM), the marine diamond subsidiary of the De Beers Group, will carry out the project with geological input from Placer Solutions (PSL). DBM bring a wealth of expertise and advanced technology to the project, developed during their 20 years of exploration and mining of diamond placers on the Atlantic shelf of southern Africa, where they have also maintained a strong environmental record. &nbsp; Glaciers and high-energy rivers emanating from the Southern Alps have transported substantial quantities of gold bearing sediment onto the Westland continental shelf during Pleistocene glacial periods, when fluvial gradients are steeper, sea level is c.120 m lower and most of the shelf is exposed. These deposits have been extensively reworked by the advancing shoreline and marine processes during interglacial marine transgressions, and most are now buried beneath a variable thickness of post-glacial marine sand, silt and mud. DBM will use side-scan sonar, swath bathymetry, Chirp sub-bottom profiling and a magnetometer to map the sea floor and sediments beneath it, guided by PSLÆs predictive geological model for gold distribution on the shelf. Cactus grab and vibro-core samples will be used to ground-truth the geophysics and provide stratigraphic, sedimentological and gold distribution data for incorporation into the geological model. Areas of interest identified by the geophysical and sampling data will be investigated in more detail, with closer-spaced geophysics and Mega-drill sampling to a maximum sediment depth of 20 m beneath the sea floor. These samples will be raised to the ship with air-lift suction technology, processed onboard for mineralogical and grade information, then returned to the sea floor. Environmental baseline data will be gathered from Van Veen grab samples of seabed sediment taken throughout the area during the prospecting programme.

Jan 1, 2005

By Virgil A. Marple

The objective of this contract was to investigate time-integrated and real-time methods for determining the diesel exhaust particulate concentration in underground mines, in particular, coal mines. The microorifice uniform deposit impactor (MOUDI) is recommended for obtaining the time-integrated measurement of the size distribution. The mass concentration of diesel exhaust particles can be obtained from the particle size distribution of mine aerosols. On a mass basis, diesel exhaust particles are primarily in the submicrometer size range while coal dust particles are larger. Size distribution measurements made in the laboratory and in three underground coal mines exhibited two distinct modes with the diesel exhaust particles in the smaller particle mode and the coal particles in the larger particle mode. The point of separation between the two modes occurred in the 0.7 to 1.0 pm size range. The separation was found to be independent of mass fraction of the diesel exhaust particles, particle concentration and sampling site. Methods recommended for further consideration as real-time monitors of diesel exhaust aerosols in mines are photometers and filter pressure drop techniques. A preclassifier would be required in both cases to separate the larger dust particles from the sample. The Metrex Mineral/Diesel Photometer should also be investigated further once the electronics problems are eliminated.

Jan 1, 1986